Search

Cordierite-mullite composite ceramics were prepared by solid-state method using Panzhihua low-grade Ti-rich clay, talc, and alumina. Influences of cordierite/mullite ratio, sintering temperature, and the chemical composition of clay on the phase composition, microstructure, physical properties, and thermal properties were investigated in detail. The results showed that the impurity oxides inside the Ti-rich clay had a great ability of forming liquid. Above 1300 °C, the reaction between TiO 2 of the clay and Al 2 O 3 produced stable Al 2 TiO 5 , which was conducive to decreasing the coefficient of thermal expansion (CTE). At 1300–1350 °C, the secondary mullitization caused the volumetric expansion, decreasing the bending strength and increasing the CTE. The optimum ratio of cordierite to mullite ranged from 90:10 to 80:20, and the sample fired at 1400 °C exhibited the lowest water absorption and porosity (0.64 % and 1.56 %, respectively), optimal bulk density, and bending strength (2.59 g cm−3 and 87.79 MPa), as well as better CTE, thermal conductivity, and thermal storage density (2.91 × 10−6 °C−1, 4.11 W/(m⋅K) (30 °C), and 1181 kJ kg−1, respectively). Compared with the reported values of cordierite-based thermal storage ceramics prepared by using the high-grade clay or minerals, the obtained samples showed the advantages such as lower costs for raw materials, higher bending strength, higher thermal conductivity (1.63–2 times higher), low CTE, and high thermal storage density. This study demonstrated that the low-grade Ti/Fe-rich clay has excellent cost-effective potential for the preparation of thermal storage ceramics. [ABSTRACT FROM AUTHOR]

In the domain of personal thermal protection, there is a growing demand for lightweight and efficient ceramic thermal insulation materials. However, conventional ceramic membranes face challenges such as brittleness, structural collapse, and pulverization, hindering their practical application. To address this issue, aluminum hydroxide-enhanced silica-zirconia ceramic membranes (SZ@ANFMs) have been successfully fabricated using electrospinning followed by subsequent calcination processes, and their properties have been comprehensively evaluated. The results demonstrate that SZ@ANFMs exhibit outstanding high-temperature resistance under an alcohol lamp, along with an extremely low thermal conductivity (only 0.041 W/m·K), excellent tensile strength (2.3 MPa), and flexible characteristics. This makes them highly promising in the domain of personal thermal protection. The study builds upon existing research in lightweight and efficient thermal insulation materials, offering improvements and robust support for the further development of personal thermal protection technology. [ABSTRACT FROM AUTHOR]

In this study, composite phase change materials (CPCMs) comprising hexadecylamine (HDA) (C 16 H 35 N), disodium hydrogen phosphate dodecahydrate (DHPD) (Na 2 HPO 4 ·12H 2 O), and expanded graphite (EG) were prepared using the demulsification method. These CPCMs exhibit high latent heat and stable thermal properties. This approach effectively mitigates the issues of substantial supercooling and poor thermal conductivity commonly associated with DHPD and HDA. Additionally, the inclusion of EG imparts superior morphological stability to the CPCMs. The HDA/DHPD/EG CPCMs demonstrated robust thermal and morphological stability at temperatures below 100 °C. Their latent heat reached up to 221 J/g and remained stable at this value even after 50 cold-heat cycles, thereby indicating excellent cycling stability. When EG was incorporated at 2 wt%, the thermal conductivity of the HDA/DHPD/EG CPCMs increased to 0.751 W/(m·K), indicating that the three-dimensional network structure of EG facilitates heat conduction and offers exceptional photothermal conversion capabilities, with a photothermal conversion efficiency of up to 97.1 %. The aforementioned results highlight the promising potential of the prepared CPCMs for applications in low-temperature waste heat recovery. [ABSTRACT FROM AUTHOR]

BiCuSeO, an oxide thermoelectric material with a superlattice structure, presents the advantages of affordability, low toxicity, and environmental friendliness. However, its intrinsic low electrical conductivity has impeded its possible applications. To address this challenge, we put tiny PbZr 0.52 Ti 0.48 O 3 (PZT) with varying weight percentages (x = 0, 5, 7, 9, 11) into BiCuSeO (BCSO) to fabricate thermoelectric nanocomposites. Through the spark plasma sintering process, PZT particles underwent in-situ decomposition, generating nano-sized second phases such as PbO 2 , TiO 2 , and PbZrO 3 , which are homogenously distributed within BCSO matrix (validated by XRD and TEM). The introduced PbO 2 , TiO 2 , and PbZrO 3 second phases served a dual purpose: inhibiting the grain growth of BCSO and introducing additional nano-grain boundaries. This resulted in more effective phonon scattering sites, thereby reducing lattice thermal conductivity. Simultaneously, the Pb element derived from PZT decomposition was doped into the Bi site of the BCSO matrix, causing a reduction in the band gap of BCSO from 0.49 eV to 0.388 eV and a significant increase in carrier concentration. Consequently, this doping enhanced the electrical conductivity of BCSO-based composites, with the composite with 11 wt% PZT additive amount exhibiting a remarkable 318-fold increase, reaching 550 S/cm compared to pristine BCSO. Notably, the composite with 7 wt% PZT additive amount achieved an exceptionally low lattice thermal conductivity of 0.333 W m−1 K−1 at 823 K. Through the synergistic optimization of electrical and thermal transport properties, the BCSO-based composite with 7 wt% PZT additive amount obtained a ZT value of ∼0.9 at 873 K, representing a 2.45-fold increase compared to pristine BiCuSeO. This straightforward method presents a cost-effective and scalable approach to enhance the thermoelectric performance of various materials, opening new avenues for potential commercial applications. [ABSTRACT FROM AUTHOR]

Glass foams and glass-ceramic foams exhibit great potential in thermal insulation of buildings, consequently reducing the necessity for heating or cooling, and ultimately contributing to energy saving. In this study, we prepared glass-ceramic foams utilizing silicate glass as starting material and CaCO 3 as foaming agent through a thermochemical process. Foams with varying degrees of relative crystallinity were produced by controlling temperature and duration of isothermal heat treatment. The foaming mechanism in the glass-ceramics was discussed by analyzing how the heat flow, mass, and volume evolve within the powder mixture during dynamic heating. The crystallization in glass did not show any clear trend on the compressive strength of glass foams. On the other hand, the thermal conductivity of the glass-ceramic foams increases with increasing relative crystallinity. The calculated solid thermal conductivity exhibited a minimum at low relative crystallinity (<20 %). These findings are crucial for designing high performance glass-ceramic foams for thermal insulation, potentially also for fabricating glass-ceramic foams using waste glasses. [ABSTRACT FROM AUTHOR]

Thermal protection was always a prominent issue in the aerospace industry. For vehicle safety, reliability and payload requirements, thermal protection materials were usually expected to possess low density, superior mechanical and thermal insulation properties. Here, lightweight and high-strength porous mullite-silica ceramics were manufactured using particle-stabilized foaming technique. The strength and thermal insulation properties of porous ceramics modified with hollow silica spheres were significantly enhanced. A 10 wt% hollow spheres addition achieved a 28.9 % increase in strength and a 33.4 % decrease in thermal conductivity with almost constant porosity (from 86.39 % to 87.04 %). Considering the characteristics of light weight, high compression strength and superior thermal insulation performance, porous ceramics could be applied as thermal protection materials in the aerospace sector. [ABSTRACT FROM AUTHOR]

Porous high-entropy transition metal compounds, an important type of ultra-high temperature material, have attracted increasing attention in the applications of extreme environments due to their low density, good thermal insulation and stable chemical properties. A robust, flame-retardant and high-temperature resistant high-entropy carbonitride (Ti 1/5 V 1/5 Mo 1/5 Nb 1/5 Ta 1/5)(C 0.55 N 0.45) (HECN) porous ceramic was synthesized and thoroughly characterized. It exhibited a porosity of 93.5 %, a compressive strength of 1.3 MPa and a good high-temperature stability up to 1673 K, which, along with its outstanding fire-retardancy, and low thermal conductivity (as low as 0.150 W m−1 K−1 at 298 K), made it a good candidate material for thermal insulation applications in ultra-high temperature environments. Moreover, the Density functional theory (DFT) calculations predict that the [N]/([C]+[N]) ratio in HECN foam affects its lattice thermal conductivity which is decreased by 67 % upon increasing the ratio from 0 to 1/2. [ABSTRACT FROM AUTHOR]

New C/SiC composites with continuous fibers were produced through impregnation of carbon fiber preforms and consolidation by hot pressing. The resulting sintered material was investigated as a potential target for nuclear applications, such as radioisotope production. Desired properties include high porosity and high thermal conductivity to allow isotope release from the targets while working at high temperature. To this end, porosimetry and thermal and mechanical characterizations were conducted up to 1250°C. It was shown that the addition of fibers resulted in high porosity, about 40%, while maintaining a very high thermal conductivity, 40 W/m∙K at 1250°C, a value particularly attractive for the intended application. Emissivity at 1250°C was 0.76, compressive strength at room temperature was 134 MPa, and flexural strength passed from about 90 MPa before thermal conductivity measurements to 50 MPa after the tests. [ABSTRACT FROM AUTHOR]

During the machining of Inconel 718 using SiAlON ceramics, the tool life can be significantly influenced by diffusion wear. To investigate this crucial wear behavior, this study focuses on the thermochemical interactions in the diffusion couple between SiAlON ceramics and Inconel 718 superalloy. So, we examine the microstructural characteristics and phase formation behavior in the reacted layer between these two materials. The interfaces between these two materials exhibit distinguishable elemental contrasts and phase formations. Particularly, the phases indicate vitrification or devitrification in the diffusion layer, influenced by the chemical composition. This issue in the diffusion couple was analyzed with thermophysical properties using light flash analysis (LFA). After, it was confirmed that the vitrification of the diffusion layer can be induced by the conduction behavior of heat trapped between SiAlON and Inconel 718 during supercooling. These characterizations verify that the devitrification of the welding layer (diffusion layer), resulting from the reaction between SiAlON ceramics and Inconel 718 superalloy, can depend on the thermal conductivity of the prepared ceramics. Furthermore, we discovered a possibility that this could contribute to improving tool performance by suppressing diffusion wear. [ABSTRACT FROM AUTHOR]

This work addresses the problem of obtaining of Ca 3 Co 4 O 9+δ -based ceramics with enhanced thermoelectric performance. Phase-inhomogeneous layered calcium cobaltite ceramics with cationic nonstoichiometry were prepared by solid-state reactions method and a field assisted sintering technology (FAST). Comprehensive experimental characterizations were conducted on the prepared bulk samples, focusing on their phase composition, as well as thermal (including thermal expansion, thermal diffusivity, and thermal conductivity), electrical (encompassing electrical conductivity and the Seebeck coefficient), and functional properties (such as power factor and figure-of-merit). The FAST technique allowed to obtain ceramics with low porosity and high electrical conductivity, which increased as the Ca:Co ratio within the samples decreased, while sample phase inhomogeneity considerably increased the Seebeck coefficient. The best thermoelectric performance was demonstrated for cationic nonstoichiometric Ca 3 Co 4.4 O 9+δ , which power factor and figure-of-merit values at 825 °C reached 427 μW⋅m−1⋅K−2 and 0.146, respectively. • Ca 3 Co 4 O 9+δ -based ceramics prepared by field assisted sintering technology possessed low porosity and high conductivity. • Electrical conductivity of bulk samples increased at decreasing Ca:Co ratio. • Phase inhomogeneity of prepared ceramics increased the Seebeck coefficient. • Ca 3 Co 4.4 O 9+δ ceramics showed the best thermoelectric performance. [ABSTRACT FROM AUTHOR]

YBCO openwork structures were 3D-printed as cuboids with 4.5 × 4.5 × 2 mm dimensions and various filling degrees. Initial pycnometric data showed a slight variation in specimen densities (∼6.153 g/cm3), proving the production process uniformity. The consistency of YBCO superconducting phase (Y-123) was confirmed by Raman spectroscopy, X-ray diffraction and X-ray absorption spectroscopy. Microstructural and chemical homogeneity was proven by scanning electron microscopy with microprobe analysis. Transport (electrical and thermal) measurements accompanied by simulations of magnetic flux density at the produced structures revealed that they are heavily dependent of filling ratio and geometry. Additionally, this work proves that the 3D printing is an excellent method of fabricating high-quality superconducting structures of desired shapes accordingly to applicational demands. [ABSTRACT FROM AUTHOR]

High-entropy ceramics have garnered significant attention in recent years owing to their exceptional properties and structural diversity. In this work, single-phase medium/high entropy ceramics, namely (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.5 Ti 0.5)O 3 and (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.1 Ti 0.9)O 3 , were successfully designed and prepared utilizing Spark Plasma Sintering (SPS). A comprehensive investigation was conducted into the phase structure, microscopic morphology, dielectric properties, and thermal behavior of these ceramics. It was observed that all ceramics maintained a cubic perovskite structure (space group: Pm 3 ‾ m), and the introduction of multi-element doping rendered them more stable across a wide frequency and temperature range. Notably, (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.5 Ti 0.5)O 3 exhibited remarkably low dielectric loss (0.0001 at 1 kHz) at room temperature, along with excellent dielectric temperature stability (25–400 °C). By reducing the zirconium concentration in (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.1 Ti 0.9)O 3 , a slight decrease in dielectric temperature stability was observed (25–350 °C); however, it demonstrated lower thermal conductivity (0.41 W/(m·K), 1200 °C) and maintained good high-temperature stability. The discovery highlights the promising practicality of both ceramics for high-temperature dielectric applications. [ABSTRACT FROM AUTHOR]

Aluminum nitride (AlN), prized for its high thermal conductivity and electronic insulating properties, finds widespread use in electronic applications, particularly as a substrate material. However, its relatively low fracture toughness limits its application. In this study, to enhance both the thermal and mechanical properties of AlN ceramics, we thoroughly investigate the microstructure, thermal, and mechanical properties of self-reinforced AlN ceramics fabricated by spark plasma sintering, with self-reinforcement achieved through the integration of AlN whiskers within the AlN matrix. Unlike previous studies utilizing conventional pressureless sintering with limited sintering conditions, this work employs spark plasma sintering with a wide range of temperatures (1600–1900 °C) and holding times (10–30 min), providing a comprehensive understanding of the sintering behavior. Microstructural features, observed through optical and scanning electron microscopy, reveal distinct toughening mechanisms via crack deflection and branching, with a maximum 20% enhancement. The self-reinforced AlN ceramics exhibit remarkable improvements in thermal conductivity, reaching up to 150 W m−1 K−1, surpassing reported values for spark plasma-sintered AlN ceramics. Adding AlN whiskers enhances the thermal and mechanical properties of AlN simultaneously, particularly at 1800 °C for 10 min with controlled grain size and nicely integrated AlN whiskers. This work not only contributes valuable insights into the complex relationship between processing parameters, microstructure, and resulting thermal and mechanical properties but also highlights the enhanced thermal and mechanical properties of self-reinforced AlN ceramics. [ABSTRACT FROM AUTHOR]

The thermal barrier coatings (TBCs) system, a pivotal technology for advanced aviation engines and ground gas turbines, mitigates direct interaction between high-temperature gas and high-temperature alloy substrates. In this investigation, a series of high-entropy Eu 2 B 2 O 7 (where B = Y, Yb, Ce, Zr, Hf, Ta, and Nb) oxides were synthesized through solid-state reactions. By manipulating B-site cations and introducing substantial atomic size disparities, as well as mass and charge disorder, we synthesized a highly disordered high-entropy Eu 2 B 2 O 7 oxide. This oxide exhibits a disordered fluorite structure and commendable thermal insulation attributes. The observed thermal conductivity of Eu 2 (Y 0.2 Yb 0.2 Zr 0.2 Nb 0.2 Ta 0.2) 2 O 7 ranges from 0.94 to 1.13 W·m–1·K–1, which can be ascribed to amplified lattice anharmonicity and disorder causing supplementary phonon scattering. In addition, It also shows the thermal expansion coefficient of 10.52 × 10−6 K−1 and high-temperature stability. These results denote that the high-entropy Eu 2 B 2 O 7 oxide may become a prospective contender for thermal barrier coatings and thermal insulators. [ABSTRACT FROM AUTHOR]

The effects of Ta doping on the thermal and electrical properties of SnO 2 varistors were researched. The results showed that the thermal conductivity is 2.01 WK−1m−1, the nonlinearity coefficient is 43, and the leakage current density is 0.7 μA/cm2 when the Ta doping level reaches 0.2 mol%. According to the measurement results of the EPR, SEM/EDS, and XRD, the Ta dopant can reduce the oxygen vacancy concentration, which was generated during the sintering. The decline of the oxygen vacancy concentration reduces the phonon scattering, then the thermal conductivity of the varistors is improved. On the other hand, the reduction of the oxygen vacancy concentration elevates the barrier height, so the nonlinearity coefficient is improved and the leakage current density is declined. [ABSTRACT FROM AUTHOR]

In present work, high entropy (MoTaTiVW)C X ceramics with different carbon stoichiometries (X = 3–6) were produced using spark plasma sintering. The microstructure, mechanical properties, and thermal properties of (MoTaTiVW)C X with different carbon stoichiometries were studied. At X = 3, the carbon deficiency resulted in a multiphase structure of the sample, (MoTaTiVW)C 3 with a Mo-rich carbide phase. At X = 3.5, the single-phase rock salt structure was formed despite carbon vacancies of up to 30 %. The relative density of (MoTaTiVW)C X gradually decreases as the carbon stoichiometry increases from X = 3 to X = 6. The concentration of carbon vacancies affects the sintering activation energy, which can enhance mass transfer and promote the densification process. The Vickers hardness of (MoTaTiVW)C X shows an overall decreasing trend as the carbon stoichiometry increases from X = 3.5 to X = 6, peaking at 20.4 ± 0.4 GPa at X = 3.5. The fracture toughness increases and then decreases, peaking at 4.4 ± 0.2 MPa m1/2 at X = 4. The thermal conductivity of (MoTaTiVW)C X gradually increases, then decreases and finally increases with the increase of carbon stoichiometry. At room temperature, the maximum value of thermal conductivity is 6.35 ± 0.29 W/m·K of (MoTaTiVW)C 5 and the minimum value is 5.32 ± 0.35 W/m·K of (MoTaTiVW)C 5.5. At 1000 °C, the thermal conductivity of (MoTaTiVW)C X ranges from 15.94 ± 0.37 W/m·K to 19.56 ± 0.45 W/m·K. As the concentration of carbon vacancies decreases, the decrease in point defect concentration will reduce the degree of lattice distortion, thereby reducing phonon scattering and affecting thermal conductivity. The study suggests that carbon stoichiometry can be used to adjust the microstructure, mechanical properties, and thermal properties of high entropy carbide ceramics. [ABSTRACT FROM AUTHOR]

First-principles computations are used to investigate the structural, stability, mechanical, optical, thermal, and electronic characteristics of perovskite material. A novel RbBa 2 Ti 3 O 10 perovskite material is studied by using the generalized gradient approximation (GGA) suggested by Perdew, Burke, and Ernzerhof (PBE) approach in the CASTEP code. According to findings, the compound structure is tetragonal in nature with a space group of 123 (p4/mmm), a lattice parameter, and a volume. RbBa 2 Ti 3 O 10 exhibits indirect bandgap semiconductor behavior, according to its electronic characteristics. The Kramer-Kroning (KK) relations are used for determining optical properties to observe light-matter interaction. Perovskites' mechanical attributes, including their ductility, compressibility, elastic anisotropy, modulus, and mechanical index, were assessed and assigned. The thermal properties of the compound are examined, including its density, minimum thermal conductivity, melting temperature, and Debye temperature. Our investigation shows that RbBa 2 Ti 3 O 10 has potential use in photocatalytic applications. • The compound structure is tetragonal with a space group of 123 (p4/mmm). • RbBa 2 Ti 3 O 10 exhibits indirect bandgap (1.66 eV) semiconductor behavior. • Perovskites' mechanical attributes, like compressibility, anisotropy, modulus, and mechanical index, were assessed. • The thermal properties are examined, including its minimum thermal conductivity, melting temperature, and Debye temperature. • RbBa 2 Ti 3 O 10 has potential use in photocatalytic applications to separate water for H 2 and O 2 production. [ABSTRACT FROM AUTHOR]

Gadolinium Zirconate nanoparticles were synthesized by Co-precipitation and Ball milling techniques. In this study, the effect of the synthesis technique and calcination temperature on the structural, morphological and thermal properties were investigated. The thermal properties examined showed that the GZ nanoparticles obtained from CP technique suffered two-fold weight loss as compared to BM technique. The SEM results revealed the formation of agglomerated particles. However, TEM results confirms the formation of nanoparticles of 10.5 nm and 8 nm by BM and CP techniques respectively. GZ particles obtained through CP technique showed better uniformity of particle size over BM technique. The functional groups of the nanoparticle were studied using FT-IR spectroscopy analysis. The XRD results confirm the formation of defect-fluorite structure and pyrochlore structure for the samples calcined at 1100 °C and 1400 °C (BM) respectively. The formation of the corresponding structures was further confirmed by Raman Spectroscopy. The thermal conductivity of the nanoparticle produced by ball milling and co-precipitation technique is almost same. As compared to NiCrAlY and uncoated substrate materials, the micro hardness of the GZ coatings has the maximum hardness of 594.6 HV, indicating the improved hardness behavior of TBC system. [ABSTRACT FROM AUTHOR]

Cubic boron nitride (cBN) has been used as a tool material for several decades due to its high hardness and thermal stability. Various binders are commonly added to cBN to synthesise cBN composites for better cutting performance. However, most studies have only investigated properties such as hardness and bulk modulus, without comprehensively studying elastic properties through experiments. In this study, the sound velocities and elastic properties of cBN with AlN binder were determined by using the ultrasonic interferometry technique. The bulk and shear moduli with their pressure dependence were determined as B 0 = 351 (3) GPa, G 0 = 344 (3) GPa, B 0 ′ = 4.32 (4) and G 0 ′ = 1.74 (2) using the finite strain equation-of-state approaches. Elasticity-related thermal properties, such as Debye temperature, Grüneisen parameter, thermal conductivity and coefficient of thermal expansion were also estimated. The results show that the elastic properties of the cBN composite with vol. 8.8% AlN-binder are comparable to the pure cBN compact. Additionally, the thermal conductivity and coefficient of thermal expansion have little effect on cBN composite with AlN binder compared to pure cBN. [ABSTRACT FROM AUTHOR]

The properties of rare-earth (RE) monosilicates can be regulated by solid solution engineering based on the mixture rule. The combination and number of RE principals are critical factors for better performances. In the present study, four single-phase equimolar multicomponent RE-monosilicate solid solutions including (Dy 1/3 Er 1/3 Yb 1/3) 2 SiO 5 , (Ho 1/3 Er 1/3 Yb 1/3) 2 SiO 5 , (Y 1/4 Er 1/4 Tm 1/4 Lu 1/4) 2 SiO 5 and (Dy 1/4 Er 1/4 Tm 1/4 Yb 1/4) 2 SiO 5 were synthesized by solid-state reaction and hot-pressing method. The microstructures, thermal and mechanical properties, and corrosion resistance to high-temperature water vapor were systematically investigated. Compared to the single-principal and ternary RE-monosilicates, the quaternary RE-monosilicates exhibited lower thermal conductivity of 1.32 Wm−1K−1 at 400 °C, matched thermal expansion coefficients (3.3 × 10−6/oC ∼ 5.8 × 10−6/oC from 200 °C to 1000 °C) with SiC, and much lower weight loss during water vapor corrosion. The results indicate that the increase of the RE element number can promote the grain growth, lower the thermal conductivity and thermal expansion coefficient, and enhance corrosion resistance. [ABSTRACT FROM AUTHOR]

There is a notable scarcity of reference data on the thermal conductivity of orthohydrogen in both vapor and liquid phases within the open literature, compared to parahydrogen and normal hydrogen. An improved corresponding states principle (CSP) model is proposed to predict the thermal conductivity of orthohydrogen by employing an optimized shape factor, which is expressed as a correlation with respect to pressure and temperature from the triple point to 300 K and at pressures up to 20 MPa. Critical parameters, ideal state thermal properties, and eccentricity factor are involved in the calculation as input parameters. The feasibility and accuracy of the proposed CSP model is verified by using experimental data of parahydrogen and some theoretical data of orthohydrogen. The estimated uncertainty of the model against high-precision experimental data of parahydrogen is within ±2.82 %. When the model is applied to dilute gas orthohydrogen, the predictions exhibit a deviation of less than ±5 % compared to other methods found in the literature. In addition, a correlation for thermal conductivity of parahydrogen, presented as a single function of temperature, is also proposed along the vapor-liquid equilibrium at temperatures from the triple point to the critical point, with an uncertainty of ±3 %. [ABSTRACT FROM AUTHOR]

In the thermal protection system of spacecraft, the bolts connecting the ceramic to the internal superalloy need to have low thermal conductivity and high strength. Two dense high entropy fluorite oxides (Zr 1/7 Hf 1/7 Ce 1/7 Y 2/7 La 2/7)O 2-δ (ZHCYL) and (Zr 1/8 Hf 1/8 Ce 1/8 Y 1/4 La 1/4 Pr 1/8)O 2-δ (ZHCYLP) were designed and synthesized by using the synergistic effect of plasma-assisted ball milling and spark plasma sintering(SPS). Through the synergistic effect of lattice distortion and oxygen vacancy guided by entropy regulation, ZHCYLP synthesized in this study has lower thermal conductivity(1.13 W·m−1·K−1), higher high temperature strength(192 MPa at 1000 °C) and high temperature phase stability up to 1600 °C than 8YSZ ceramics. The thermo-mechanical coupling finite element analysis results of high temperature bending test show that the variation trend of the maximum stress value of the sample is consistent with the experimental results. This shows that the mechanical and thermal properties of high entropy oxides can predict the variation trend of the maximum stress value in high temperature bending tests. It opens up a new way for designing and synthesizing high entropy oxide materials with low thermal conductivity and high strength which can be applied in the field of heat protection and load bearing. [ABSTRACT FROM AUTHOR]

The pyrochlore oxide La 2 Hf 2 O 7 (LHO) has attracted extensive attention in thermal management applications. Accurate determination and comprehensive understanding of thermal conductivity (κ) stand as imperative prerequisites for the effective utilization and manipulation of LHO in various applications. In this study, with the assistance of machine learning interatomic potential, we investigate the microscopic mechanisms of phonon thermal transport in LHO crystals. Our findings show that the thermal transport in LHO defies a precise explication through the conventional framework of the Boltzmann transport equation (BTE) due to the emergence of diffusive phonon modes, engendered by strong anharmonicity. Using the state-of-the-art dual-phonon model incorporating both propagating and diffusive modes, we successfully reproduce the experimentally measured results in both magnitude and temperature dependence. It is also shown that the thermal conduction in LHO crystals is dominated by the propagating modes at low temperatures while by the diffusive modes at high temperatures, which synergistically lead to a low κ for LHO crystals. The novel insights into phonon thermal transport provide a stepping stone for regulating the thermal transport properties of LHO crystals. [ABSTRACT FROM AUTHOR]

Pr doped La 2 Zr 2 O 7 (LPZ) TBCs have been deposited by electron beam physical vapor deposition. This work concentrates on the thermophysical properties and microstructure evolution of LPZ/YSZ duplex TBCs before and after thermal cyclic so as to probe into the merit and the application feasibility. The thermal expansion, thermal conductivity and phase structure have been measured and analyzed in comparison to other classical TBCs materials. Typical feathery microstructure and intra-columnar gaps did not provide desired thermal cyclic counts for LPZ/YSZ TBCs. Two principal categories of degradation mechanism limited the cyclic lifetime. The first principal degradation mode is the pulverization of LPZ after thermal cyclic due to the Pr rare earth elements modification in lanthanum Zirconates. Pr instability created the pulverization degradation mode instead of spalling. The second degradation mode is the cracks extension paralleled to interface inside TGO due to the brittle spinel generated by excessive oxidation. This study of thermal properties and degradation mechanism might offer thought and inspiration for other advanced TBCs. [ABSTRACT FROM AUTHOR]

By applying the high-entropy strategy, one can develop stable mixed oxide by populating a single sublattice with many distinct cations. Two kinds of rare-earth high-entropy hexaaluminates (La 1/5 Nd 1/5 Sm 1/5 Eu 1/5 Gd 1/5)MAl 11 O 19 (M = Mg and Zn) were successfully synthesized, and their mechanical and thermal properties were analyzed. We highlight that the Zn-containing sample displays a significant increase in fracture toughness (2.48 MPa m1/2) and a decrease in thermal conductivity (1500 °C, 1.2 W m−1 K−1) as compared to the Mg-containing sample. The diffusion of fine grains in platelet-like grains observed only in the Zn-containing sample is considered to be responsible for its outstanding mechanical properties. This work demonstrates the excellent thermal-mechanical properties of the Zn-containing sample and indicates the promising use of high-entropy hexaaluminate in the aerospace field acting as thermal barrier coating materials. [ABSTRACT FROM AUTHOR]

This work describes the preparation and properties of a novel category of thermosetting microwave absorbing composite materials. The composites were prepared by a simple solution casting process, employing high temperature resistant polysilylaryl-enyne (abbreviated as PSAE) resin as matrix and perovskite CaMnO 3 (abbreviated as CMO) ceramic filler as absorbent filler. The microstructure, electromagnetic, wave absorbing and thermal properties of the CMO-PSAE composites were all examined. The results showed that the increasing fraction of CaMnO 3 filler not only densified the microstructure of the composites, but also greatly improved their temperature resistance, thermal conductivity and wave absorption properties. The CMO-PSAE composite doped with 50 vol% CaMnO 3 ceramic filler showed the strongest ability to absorb electromagnetic waves, with an effective absorption bandwidth (EAB) of 4.16 GHz and a minimum reflection loss is −53.01 dB. Besides, the thermal conductivity of the composite reached 1.106 W/(m·K). Furthermore, this composite material has exceptional thermal resistance, with the highest T d5 reaching 650 °C. Composites with varying doping levels can be used for specific performance needs in practical scenarios. Thus, such novel CMO-PSAE composites exhibit potential applications in the electromagnetic countermeasure field under high-temperature environments. [ABSTRACT FROM AUTHOR]

[Display omitted] • CNTs-related composite PCMs are categorized in a new way: CNTs are usd as nanoadditives, porous supporters, and secondary network. • The research progress in the mechanism of heat transfer and phase transition of CNTs-related composite PCMs is introduced in detail. • In-depth insights into the micro-mechanism of heterogeneous interactions induced by CNTs are revealed. • The current challenges of designing CNTs-related composite PCMs are summarized. With the merits of inherent physicochemical properties of hollow structure, high mechanical strength, thermal stability, ultrahigh light absorption capacity, and ultrahigh thermal conductivity, carbon nanotubes (CNTs) are extensively used to enhance the thermal storage capabilities of solid–liquid phase change materials (PCMs). Interestingly, CNTs can act as thermally conductive additives and supporting skeletons when marring with PCMs. The state-of-the-art reviews on PCMs pay attention to carbon-based porous composite PCMs or nanoparticle dispersed PCMs, CNTs-derived PCMs only share a small part, lacking of a comprehensive review for multifunctional CNTs compounded PCMs. Herein, focusing on the enhancement effects of CNTs on PCMs, we retrospectively describe composite PCMs with a novel category way, by using CNTs as nanoadditives, porous supporters, and secondary network. We emphasize the micro-mechanism of heterogeneous interactions induced by CNTs: crystallization behavior, interfacial thermal resistance, thermal conductivity, phonon transport. Simultaneously, we provide in-depth insight into relationship between micro structural and thermal properties of CNT-derived PCMs. As a result, some different pathways of modern utilization based on the improved PCMs are presented. Finally, we outline the current challenges of designing CNTs to enable advanced functional thermal storage materials. The review aims to inspire clever use of CNTs into PCMs for targeted applications. [ABSTRACT FROM AUTHOR]

In this study, a highly dense GdB 6 bulk ceramic material was fabricated using one-step in-situ reaction spark plasma sintering technology. The sample with a relative density of 96.7 % and a purity of 96.9 wt% was successfully obtained by sintering at 1800 °C for 30 min under a uniaxial pressure of 50 MPa. The Vickers hardness, elastic modulus and fracture toughness of the as-obtained GdB 6 bulk ceramics were 18.9 GPa, 209 GPa and 1.6 MPa·m1/2, respectively. The thermal conductivity of GdB 6 at room temperature was 28.68 W·m−1·K−1, 70 % of which was mainly attributed to phonon vibration, while the remaining 30 % to the electrical thermal conductivity. In addition, the as-obtained GdB 6 ceramics showed no phase transformation after heat treatment at a relatively high temperature of 2100 °C for 20 min in Ar atmosphere. The highly covalent octahedral boron framework played a critical role in maintaining the phase stability of the GdB 6 crystal lattice. This suggested that GdB 6 ceramics could be used as potential ultra-high temperature ceramics for aerospace applications and high-power vacuum electronic devices operated at high temperatures. [ABSTRACT FROM AUTHOR]

Rare earth compounds (RE 2 O 3), typically Eu 2 O 3 and Gd 2 O 3 , are considered as absorbing materials due to their long chain neutron absorbing ability and high efficiency of neutron absorption. In this paper, a specifically designed x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 (x = 0.6, 0.7, 0.8, 0.85) composite ceramics with excellent thermal properties were synthesized through direct thermal decomposition reactions followed a high-temperature sintering method under vacuum conditions. X-ray diffraction (XRD) and Raman spectroscopy analysis indicated that the obtained ceramics consisted of monoclinic Eu 2 O 3 and fluorite Gd 2 Zr 2 O 7 phases. The hardness of x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 ceramics (x = 0.8, 0.85) have no significantly changes in the test temperature range (25–350 °C). The thermal expansion coefficients (TECs) (7.3–10 ×10-6 K-1) are lower than Dy 2 TiO 5 (9.3–10.4 ×10-6 K-1), and the thermal expansion rate changes linearly with the increase of temperature, which indicates that the x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 ceramics exhibit excellent high temperature phase stability. Furthermore, the range of thermal conductivities is from 0.96 W·m-1·K-1 to 2.02 W·m-1·K-1 (25–800 °C), which is higher than Dy 2 TiO 5 (0.27–0.55 W/m·K, 220–650 °C). Compared with the state-of-art Dy 2 TiO 5 ceramics, x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 have superior thermal properties and are therefore expected to be the next generational of neutron absorbent materials used in ash rod. [ABSTRACT FROM AUTHOR]

The order-disorder transition (ODT) of RE zirconate (RE 2 Zr 2 O 7) has received much attention due to its potential applications in the design of thermal barrier coatings (TBCs). A series of high entropy RE zirconates (RE = La, Sm, Gd, Er and Lu) were designed and synthesized in order to regulate the fluorite-pyrochlore phases, and to investigate the effect of phase composition on the microstructures and performances. The results showed that the sintering temperature, as well as equivalent ion radius, played an important role in regulating the phase transformation of fluorite-pyrochlore. The coexistence of pyrochlore-fluorite phases not only can result in the decrease in grain size but also increased the lattice strain of each phase, thereby enhancing the phonon scattering and contributing to the reduction in the thermal conductivity. The CMAS corrosion resistance was mainly related to phase compositions, and the thicknesses of reaction layer decreased gradually with the increasing fluorite phase content. The results will provide theoretical guidance for the microstructural design of high entropy RE zirconates as next generation TBC materials in future. [ABSTRACT FROM AUTHOR]

Microwave heating has been applied to improve cement-based materials (CBMs) structures deicing efficiency, which reduce the effect of icing on their service life. Moreover, the enhanced thermal properties of CBMs can further improve their deicing efficiency. In this study, silicon carbide (SiC) ceramic particles with favorable thermal properties were used to prepare the SiC cement-based materials (SCBMs). The effect of SiC ceramic on the mechanical strength of CBMs was investigated. Next, the heat transfer and storage ability of CBMs were investigated to analyze the changes in their thermal-physical parameters. Then, the surface thermal responses of the CBMs during microwave heating and off were recorded to characterize their temperature evolution in a low-temperature condition. Furthermore, the deicing efficiency of CBMs was determined using the ice layer shedding time (ILST) as the index. The results show that the filling effect of SiC ceramic on CBMs improved their mechanical strength within a certain content range. However, a large content of SiC ceramic caused an increase in the weak area and porosity within the CBMs, further reducing their mechanical properties. The thermal-physical parameters of CBMs were improved after adding SiC ceramic. The thermal conductivity and thermal effusivity of SCBMs-100 were 13.17 W/(m·K) and 1.44 W/(mm2·K), respectively, 7.90 and 2.35 times higher than the control group. Due to the favorable thermal properties of SCBMs, their heating rate and surface temperature field distribution characteristics were further improved. Furthermore, with the increase of SiC ceramic content, the ILST of SCBMs was further reduced during microwave heating. Therefore, the SiC ceramic was a favorable material, improving the thermal properties and deicing efficiency of CBMs to a certain extent. However, considering its effect on the deterioration of the mechanical properties of CBMs, the optimal content of SiC ceramic might be 75%. [ABSTRACT FROM AUTHOR]

The rapid development of micro-electronics has a growing demand on the heat dissipation performance of devices, especially thermal management materials. However, recent researches focus on the improvement of single ability, such as thermal or mechanical properties. Herein, a strategy that simultaneously improves thermal and mechanical performance of thermal manager material was proposed, which was achieved by preparing Cu-SiC w composites via the co-electrodeposition technology. The influence of electroplating parameters, such as temperature, current density and reinforcement contents, on the microstructure evolution, mechanical and thermal conductivity were investigated systematically. The fabricated SiC w composite displayed excellent shear strength up to 420 MPa, which is resulted from the Orowan strengthening and load transferring. Additionally, the thermal conductivity of 340 W/(m·K) was obtained, owing to the uniform distribution of whiskers and good interface between the Cu matrix and whiskers. Therefore, the presented work provided an effective method for fabricating comprehensive thermal-mechanical properties and homogeneous heat dissipation capacity Cu-SiC w composites and paved the way for the practical application in the field of the connector between the power devices and heat sinks. [ABSTRACT FROM AUTHOR]

The mechanical and thermal properties of ZrC x are strongly dependent on the composition and microstructure. In the present study, densified ZrC x (x = 0.5, 0.7 and 1.0) with relative density in the range of 99.2–99.7% have been prepared by a combination of spark plasma sintering (SPS) and vacuum arc melting (VAM). Both the Young's modulus and Vickers hardness monotonically increase with increasing C/Zr ratio. The maximum Young's modulus and Vickers hardness values of 488.1 ± 13.4 GPa and 28.8 ± 1.7 GPa, respectively, for dense ZrC have been obtained. With increasing the C/Zr ratio, the thermal conductivity of ZrC x increases. The thermal conductivity ZrC ranged from 25.17 W/m/K to 43.85 W/m/K from ambient to 1200 °C. Owing to the higher density of ZrC x , the present thermal conductivities and Young's modulus of ZrC x are higher than those of the previous studies. The present results are beneficial to design and preparation of ZrC x ceramics. [ABSTRACT FROM AUTHOR]

Flexible SiC nanowire aerogel felt has excellent foldability, high-temperature resistance, and thermal insulation properties. However, the large-scale and high-efficiency production of SiC nanofiber aerogel felt remains a challenge. In this work, a three-dimensional network-structured short-chopped carbon fiber felt was used as a template for preparing SiC nanowire aerogel felt. The short-chopped carbon fibers were combed and dispersed using an airflow in a carding machine to obtain the desired felt. This method enables rapid and uniform preparation of carbon fiber felt, enhancing the efficiency of SiC nanowire aerogel felt production. The experimental results showed that the aerogel felt was mainly composed of β-SiC nanowires with a density of 5.29 g/cm3. Additionally, the SiC nanofiber aerogel felt exhibited remarkable superelasticity and low thermal conductivity (0.013 W/m·K). This research contributes to the practical application of flexible SiC nanowire aerogel felt in the field of thermal insulation. • Carding machine dispersed carbon fiber. • Fabrication of large size SiC nanofiber aerogel felt. • SiC nanofiber aerogel felt has flexibility and low thermal conductivity. [ABSTRACT FROM AUTHOR]

Current highly integrated devices require heat interface materials with excellent heat conductivity. A simple approach was employed to synthesize thermally conductive and outstanding thermal stability nanocomposite. Calcium carbonate nanoparticles (nano CaCO 3) reinforced with reduced graphene oxide (rGO) nanoparticles (rGO/CaCO 3) are synthesized using a novel process, and the effect of rGO in CaCO 3 structure is examined by Field Emission Scanning Electron Microscope, X-ray diffraction, TGA-DTA, and thermal conductivity. The experimental results show that adding rGO resulted in higher crystallinity and thermal stability. As the wt.% of rGO increases from 1 to 5%, the crystallite size was suppressed by 21.06%, 27.39%, 32.48%, 41.5%, and 45.30%, respectively, compared to the pure nano-CaCO 3. Additionally, rGO enhances the thermal conductivity by 35.31% and thermal diffusivity to 1.834 mm2/s by adding 5% rGO. [ABSTRACT FROM AUTHOR]

Among the family of high-quality fiber materials, mullite fiber membrane is a promising one that possesses abilities of both the thermal resistance and oxidation resistance under high temperature. High-purity mullite nanofibrous membranes were prepared by electrospinning method with low-cost aluminum chloride hexahydrate (AC) as the aluminum source. The effects of sintering temperature and AC content on the phase structure, microstructure, thermal and mechanical properties of the mullite nanofibrous membranes were investigated. The results show that the sintering temperature as low as 1000 °C is the very appropriate temperature for obtaining the high-purity mullite nanofibers with smooth surface. The minimum thermal conductivity of 0.029 W m−1 K−1 and maximum tensile strength of 6.11 MPa are gained from the mullite nanofibrous membranes with AC content of 2 mmol. The mullite nanofibrous membranes with excellent properties can be selected as an ideal candidate for thermal insulation and reinforced applications. [ABSTRACT FROM AUTHOR]

Conducting in-situ measurements of planetary environments is a key scientific goal in the geoscience field for the extraterrestrial exploration, such as the Moon or Mars. Among these measurements, determining the thermal properties of regolith is particularly challenging due to the material's inhomogeneities. In this paper, an active thermal probing technique is proposed, utilizing a transient hot-wire technique with a needle-like probe structure integrated with temperature sensors and a heater. It is capable of measuring in-situ temperature variations and inner heat flux without disturbing the surrounding regolith. In addition, a machine-learning-based method is proposed for inverting in-situ thermophysical properties, including density, thermal conductivity, and heat capacity. An embedded artificial neural network model has been developed and trained with data sets from both finite element simulations and experiments. This machine learning model is capable of efficiently predicting temperature responses for different lunar regolith simulants. For total 12 parameters, the errors of ten cases are less than 10%, and other two cases are 12.23% and 13.17%. Finally, the proposed method is verified by heat measurement experiments under normal pressure and vacuum, and the variation of thermal properties with different compactness is obtained. The proposed probing technique provides novel ideas to measure the in-situ thermal properties of extraterrestrial regolith. [ABSTRACT FROM AUTHOR]

It is difficult to obtain X2-type rare-earth monosilicates that have the advantages of low thermal conductivity and a thermal expansion coefficient that matches that of ceramic matrix composites, and thus, the efficient use of these materials in extreme environments is challenging. In this study, we developed a novel component regulation method, which significantly reduced thermal conductivity and helped achieve a suitable thermal expansion coefficient for monosilicates. Monosilicates have low thermal diffusion coefficients mainly due to the effect of extrinsic phonon scattering mechanisms. We analyzed different extrinsic phonon scattering mechanisms associated with point defect, disorder, grain boundary, lattice distortion, dislocation, and symmetry. • A variety of monosilicates with suitable coefficients of thermal expansion were synthesized. • The thermal conductivity of monosilicates was significantly reduced. • The various extrinsic phonon scattering mechanisms related to point defect, disorder, and more were analyzed. [ABSTRACT FROM AUTHOR]

The excellent thermal properties of diamond/SiC composites are mainly attributed to the addition of diamond particles. In order to further increase the diamond content, a novel preparation method was used to regulate the distribution of bimodal diamond particles. Moreover, in order to achieve better performance, the effects of particle size ratios on the properties were studied. The results show that with the increase of small diamond particle size, the bimodal diamond packing will change from unmixing mechanism to mixing mechanism, and the critical ratio (small/large) of entrance for 400 µm diamond particles is between 0.37 and 0.5. When the particle size ratio is 0.25, the thermal conductivity reaches the maximum, reaching 812.27 W/mK (break through 800 W/mK for the first time). In addition, the influence of particle size ratio on coefficient of thermal expansion is also discussed. [ABSTRACT FROM AUTHOR]

Hollow-structured ceramic fibers with multiple components are ideal as lightweight insulation materials. In this study, tetraethyl orthosilicate, boric acid, and zirconia octahydrate were used as raw materials for fabricating SiZrBOC hollow ceramic fibers through coaxial electrospinning. These ceramic fibers exhibit a low thermal conductivity and an excellent temperature resistance. The electrospun SiZrBOC hollow ceramic fibers display a clean and compact morphology with internal folds. Fourier-transform infrared spectroscopy and thermogravimetric analysis (TGA) were used to assess the transformation process and thermal behavior of the hollow ceramic fibers. The results suggest that the incorporation of B promotes the formation of Si–O–B bonds within the system, leading to a maximum yield of 75.49 wt% for the production of the SiZrBOC hollow ceramic fibers. The phase composition and microstructure of the SiZrBOC hollow ceramic fibers were analyzed via X-ray diffraction (XRD) measurements. The pyrolysis at 1000 °C resulted in the appearance of diffraction peaks corresponding to SiO 2 and SiC in the XRD patterns of the SiZrBOC hollow ceramic fibers. Laser thermal conductivity measurements reveal that the SiZrBOC hollow ceramic fibers exhibit a thermal conductivity of only 0.06 W‧m−1K−1 at 25 °C and 0.124 W‧m−1K−1 at 500 °C, indicating a significantly superior thermal insulation performance compared with conventional solid SiZrBOC ceramic fibers. [ABSTRACT FROM AUTHOR]

In transportation applications, filling high pressurised hydrogen tanks within a few minutes implies a fast and large temperature increase that can compromise the structural integrity of the storage system and the safety of the process. Common approaches to control this temperature increase mainly involve hydrogen pre-cooling using complex and energy-demanding refrigeration systems. This study proposes and assesses alternative and energy efficient thermal management strategies for fast filling of hydrogen tanks including the modification of the liner's thermal properties and the use of existing on-board refrigeration systems. The analysis is performed by means of a Computational Fluid Dynamics model validated against experimental observations. Results show that proposed solutions provide a robust and efficient alternative to hydrogen pre-cooling, potentially simplifying the hydrogen supply system, reducing its associated energy demand, maintaining the hydrogen temperature below admissible limits and increasing the state of charge of the tank. • Strategies are based on liner pre-cooling and its thermal properties modification. • Similar H 2 temperature is achieved when pre-cooling it or changing liner properties. • Energy consumption of liner pre-cooling is up to 42–68% lower than H 2 pre-cooling. • Liner heat capacity increase is more effective than thermal conductivity increase. • Strategies increase the SOC up to 3.5% points compared to H 2 pre-cooling. [ABSTRACT FROM AUTHOR]

In this study, we designed four groups of A-substituted medium-entropy perovskites, synthesized (Ba 0.4 Sr 0.4 Ca 0.1 La 0.1)ZrO 3 , a non-equimolar medium-entropy perovskite, and studied its microstructural uniformity. The medium entropy of these perovskites imparts unique mechanical and thermal properties. Compared to pure BaZrO 3 , the cold moduli of rupture of the four samples improved by 164.29%, 121.22%, 91.49%, and 81.87%, respectively, and the relative density increased from 69.47% to over 90%. The thermal conductivities of these materials were lower than those of conventional low-thermal-conductivity perovskite materials, with a minimum value of 1.513 W/(m·K). The high strengths and low thermal conductivities of these novel perovskite materials could provide vast opportunities for various future applications. [ABSTRACT FROM AUTHOR]

Dichromatic phosphor-in-glass films (PiFs) are recognized as ideal color converters for high-quality laser lighting, but photon reabsorption among multiple phosphor degrades the luminescence performance. Therefore, there is urgent to design a suitable PiF structure to alleviate this problem. Herein, the green-emitting phosphor YAGG:Ce and the orange-yellow-emitting phosphor GdYAG:Ce are mixed with silicate glass powder respectively, and print on the sapphire plate with high thermal conductivity (TC) to prepare spatially separated structure PiF (SS-YG PiF). Under the excitation of blue LD with power of 6.15 W, the luminous flux (LF) of SS-YG PiF reaches 1020.4 lm, and the corresponding luminous efficiency (LE) reaches 165.92 lm/W and CRI∼80. Notably, the perfect white light color coordinates (0.3354, 0.3253) are obtained at 6.15 W. In addition, SS-YG PiF has a lower surface temperature and a higher TC (9.89 W m−1K−1), reflecting the excellent luminescence performance and thermal properties of SS-YG PiF. [ABSTRACT FROM AUTHOR]

Core-shell structured copper-boron nitride (Cu@BN) spherical fillers were synthesized to fabricate thermally conductive composites. To enhance the interaction between the fillers and the matrix, polysilazane (PSZ) was coated on the surface of the filler. The resultant composite exhibited remarkable characteristics, including a substantial tensile strength of 32.36 MPa, excellent electrical insulation properties, and impressive thermal conductivity of 3.47 W/mK. When applied in a light-emitting diode (LED) application, the composite effectively managed heat, reducing the operating temperature by 34 °C. The epoxy/PSZ-Cu@BN composites hold great promise for improving thermal management in electronic devices. • The copper-boron nitride (CuBN) core-shell structured filler was fabricated. • The PSZ coating of CuBN reinforced thermal and mechanical properties of composites. • The Epoxy/PSZ-CuBN composites achieved high thermal management performance. [ABSTRACT FROM AUTHOR]

Building and construction waste contributes to global carbon emissions, leading to the need to seek alternative materials that are more environmentally friendly. Mycelium Biocomposite (MB) is a sustainable material that utilizes agricultural waste as its main substrate and can be degraded after-use. This study aimed to investigate mechanical performance of additional layers in sandwich panel fabrication of MB. The experiment was conducted in two phases including (1) Composite 1: Oil Palm Empty Fruit Bunch (OPEFB) fiber layer with pine resin and (2) Composite 2: MB sandwich panel. In Composite 1, the mechanical test results showed the S50 sample (50 % fiber and 50 % resin) had the highest tensile strength of 0.18 N/mm² and was selected as the surface layer. In Composite 2, the variable of layer binder was produced using mycelium hyphae (MB-M) and resin (MB-R). The results of the physical, mechanical, and thermal properties tests were compared with the JIS A 5905:2003 standard and previous studies. The MB sample (no layer) had the best mechanical and thermal conductivity values due to the binding method effects, such as flexural strength at 25.38 N/mm² and bending strength at 0.53 N/mm². MB-M showed incomplete drying that caused lower tensile strength and higher thermal conductivity. Meanwhile, MB-R showed mechanical values similar to MB, such as flexural strength at 21.22 N/mm² and bending strength at 0.52 N/mm². Yet, MB had higher thermal conductivity, where MB-R showed 0.1558 W/mK and MB showed 0.1037 W/mK, due to Composite 1 addition. This study suggests the development of MB thermal values and considers its application as non-structural insulation panels. • Sustainable alternative material: Mycelium Biocomposite (MB) with additional layer in sandwich panel fabrication. • Oil Palm Empty Fruit Bunch (OPEFB) with pine sap bioresin binder as additional layer. • Investigating physical, mechanical and thermal properties of Mycelium Biocomposite (MB). • Mycelium Biocomposite (MB) sample with no additional layer has a high mechanical and thermal conductivity value. • MBs exhibit potential as renewable materials and alternative insulation panels for non-structural insulation panels. [ABSTRACT FROM AUTHOR]

To design such a hybrid battery thermal management system (BTMS), it is crucial to establish a practical and realistic approach from the point of view of: i. simulated operating conditions, ii. assumed materials/compounds, iii. Fast-charging performance test. To avoid oversizing, this work considers the World Harmonized Light-duty Vehicle Test Procedure Class 3 (WLTP3) driving cycle, instead of constant charge/discharge rates. Power requirements of a medium-sized vehicle during this WLTP3 cycle have been used to estimate the heat generated by the proposed battery module (18650 NMC cylindrical cells, hexagonal arrangement). This allows the minimum mass required by the phase change materials (PCM) to maintain the battery module at a given temperature threshold to be determined. Once this PCM mass requirement was established, a comprehensive optimization of the key thermal properties that characterize PCMs was carried out, investigating carbon-based additives (CBAs) to improve the low thermal conductivity of PCMs. The results show that the proposed approach can sustain up to 10 consecutive WLTP3 driving profiles without the need for additional energy input. This approach passively minimizes energy consumption during operation and absorbs up to 27 % of the heat emitted by the cell during fast charging, reducing the liquid cooling power requirement. • A hybrid BTMS composed of ssPCMs and liquid cooling is optimized. • WLTP3 drive cycle used instead of constant rates are used to size PCM thickness. • Hexagonal cell arrangement ensures minimum space use in battery packs. • Optimal properties: Cp eff ∼85 kJ/(kg·K) and k eff ∼8 W/(m·K) with 20 wt% additive. • SsPCM holder absorbs 27 % of battery heat during fast charging. [ABSTRACT FROM AUTHOR]

This study investigates the unidirectional (UD) jute/snake plant fiber-reinforced epoxy composites with various fiber weight percentages (100/0, 75/25, 50/50, 25/75, and 0/100) manufactured by the hand lay-up technique. Their mechanical properties (tensile, flexural, and impact), thermal properties (thermal conductivity, heat resistance, thermal stability, and thermal transitions (e.g., melting, crystallization, and T g)), water absorption, and morphologies are then evaluated. It is found that the UD hybrid composite made with 25 % jute and 75 % snake plant exhibits better tensile modulus and strength of 4.02 GPa and 112.83 MPa, respectively, and maximum impact strength of 185.18 kJ/m2, whereas the UD hybrid composite of 50 % jute/50 % snake plant shows a maximum flexural strength of 159.89 MPa. The thermal conductivity of UD composites increases with the increase in snake plant fiber, and the UD hybrid composite consisting of 75 % jute/25 % snake plant displays the minimum thermal conductivity (0.20 W/mK). Thermogravimetric and differential scanning calorimetry analyses show that all UD composites offer moderate thermal stability at high temperatures. The degree of water absorption of UD composites decreases with increasing snake plant fiber, and the UD composite of 25 % jute/75 % snake plant shows minimum water absorption. The outcome of this study indicates that the UD hybrid composites with comparatively higher contents of snake plant fiber can potentially be used for applications where significant mechanical properties are required with moderate thermal stability (e.g., aircraft interior panels, car door panels, seat foundations, the inner structure of trains, helmets, surfboards, and so on). [Display omitted] • Composite comprising 25 % jute and 75 % snake plant exhibits better tensile properties and impact strength. • Flexural strength increases with increasing snake plant fiber except for slight inconsistency. • Failures of composites occur predominately due to fiber pull-out, fracture of fibers, fiber-matrix debonding, and voids. • Thermal conductivity of composites rises with the increase in snake plant fiber. • All composites represent moderate thermal stability at high temperatures. [ABSTRACT FROM AUTHOR]

With the increasing demand for highly integrated circuits to optimize energy efficiency, reduce weight, and improve mechanical properties, finding a Magnesium (Mg) matrix material with excellent mechanical strength and high thermal conductivity poses a significant challenge. In this work, titanium (Ti) particles were introduced into AZ91 (Mg-9Al-1Zn) alloy to fabricate Ti/AZ91 composites, employing a combination of stir casting, extrusion and rolling processes. This strategy simultaneously enhances the mechanical properties and thermal conductivity of the Ti/AZ91 composites compared with AZ91 alloy. The incorporation of Ti particles serves to refine grains, expediting the formation of Mg 17 Al 12 phase within the Mg matrix. Optimal comprehensive mechanical properties are attained in 10 wt% Ti/AZ91 composite, exhibiting an ultimate tensile strength of 365 MPa, an elongation of 11.9 %, and a significantly low wear rate of 4.548×10−3 mm3/m. Notably, the 10 wt% Ti/AZ91 composite shows a 41.1 % reduction in wear rate relative to the AZ91 alloy, attributed to the incorporation of hard Ti particles. Furthermore, the thermal conductivity of the 2.5 wt% Ti/AZ91 composite exhibits a significant enhancement over that of the AZ91 alloy. Detailed discussions are provided on the fundamental mechanisms responsible for strengthening, wear resistance, and thermally conductive in Ti/AZ91 composites. These results highlight the substantial potential of Ti/AZ91 composites for lightweight structural applications, such as highly integrated circuits requiring excellent mechanical properties and high thermal conductivity. [Display omitted] • The 10Ti/AZ91 composite demonstrates a remarkable improvement in UTS, EL and wear resistance. • Enhanced mechanical properties results from the deformable Ti particles, refined grains, and weakening of texture. • The Ti/AZ91 composites possess exceptional thermal conductivity while maintaining high strength. [ABSTRACT FROM AUTHOR]