Search

Objectives: This investigation evaluated the impact of multiple firings during the veneering process of anterior all-ceramic restorations on the fracture load (FL) of zirconia crowns veneered with different ceramics (ZRT, ZRO, HFZ, STR)., Methods: All-ceramic crowns with anatomically reduced zirconia frameworks were prepared using four different veneering ceramics (N = 192/n = 48 per veneering ceramic). The crowns were fired 2 and 10 times. Half of them were thermocycled (5000 cycles, 5 °C/55 °C, 20s). FL using Voss shear test was measured. Data was analyzed using ANOVA with partial eta squared and post-hoc Scheffé-test as well as t-test and Weibull analysis., Results: Regarding FL, greatest differences were among the number of firings (p<0.001, η p  = 0.369). FL was not influenced by the interaction of both number of firings and aging level (p = 0.231) and the interaction of number of firings and veneering ceramic (p = 0.222). Differences were found comparing FL values of ZRT and STR (p<0.001) and of HFZ and STR (p<0.001). No differences occurred among the veneering ceramics after 2 (p = 0.430) and after 10 firings (p = 0.057) in respect to initial FL. For all initially tested veneering ceramics, FL showed higher values after 10 firings (p≤0.001-0.014). When aged, ZRO, HFZ, and STR also provided higher FL values after 10 firings (p≤0.001). For ZRT, FL values differed between initial and aged testing after 2 firings (p = 0.001) with aged specimens providing higher FL values. After 10 firings, none of the veneering ceramics showed differences regarding FL values between initial and aged testing. Weibull modulus was higher for ZRT specimens after 10 firings when tested initially (m = 10.1) and for aged ZRT specimens after 2 firings (m = 11.1). Failures occurred either with chipping of the veneer or total fracture.2  = 0.369). FL was not influenced by the interaction of both number of firings and aging level (p = 0.231) and the interaction of number of firings and veneering ceramic (p = 0.222). Differences were found comparing FL values of ZRT and STR (p<0.001) and of HFZ and STR (p<0.001). No differences occurred among the veneering ceramics after 2 (p = 0.430) and after 10 firings (p = 0.057) in respect to initial FL. For all initially tested veneering ceramics, FL showed higher values after 10 firings (p≤0.001-0.014). When aged, ZRO, HFZ, and STR also provided higher FL values after 10 firings (p≤0.001). For ZRT, FL values differed between initial and aged testing after 2 firings (p = 0.001) with aged specimens providing higher FL values. After 10 firings, none of the veneering ceramics showed differences regarding FL values between initial and aged testing. Weibull modulus was higher for ZRT specimens after 10 firings when tested initially (m = 10.1) and for aged ZRT specimens after 2 firings (m = 11.1). Failures occurred either with chipping of the veneer or total fracture., Significance: Veneered zirconia restorations tested presented higher FL after 10 firings compared to 2 firings. Aging via thermocycling showed a positive effect on the FL., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Although FDA approved and clinically utilised, research on 45S5 Bioglass® and S53P4 including other bioactive glasses continues in order to advance their applicability for a range of alternate applications. For example, rendering these particles porous would enable incorporation of varying biological payloads (i.e. cells, drugs and growth factors) and making them spherical would enhance their flow properties enabling delivery to target sites via minimally invasive injection procedures. This paper reports on the manufacture of solid (non-porous; SGMS) and highly porous microspheres (PGMS) with large external pores and fully interconnected porosity from bioactive silicate glass formulations (45S5 and S53P4) via a single stage flame spheroidisation process and their physicochemical properties including in vitro biological response. Morphological and physical characterisation of the SGMS and PGMS revealed interconnected porosity up to 65 ± 5%. Mass loss studies comparing between SGMS and PGMS revealed 1.5 times higher mass loss for the PGMS over 28 days. Also, in vitro bioactivity studies using simulated body fluid (SBF) revealed hydroxyapatite (HA) formation at earlier time point for PGMS compared to their SGMS counterparts (i.e day 1 for PGMS and day 3 for SGMS of 45S5). In addition, HA layers were also formed in cell culture media, with the exception of SGMS of 45S5, which revealed CaP formation with a ratio of 1.52-1.78. Direct cell seeding and indirect cell culture studies (via incubation with microsphere degradation products) revealed mouse 3T3 cells were able to grow and undergo osteogenic differentiation in vitro , confirming cytocompatibility of both 45S5 and S53P4 SGMS and PGMS. More importantly and especially for orthobiologic applications, cells were observed to have migrated within the pores of the PGMS. As such, the PGMS developed from these bioactive silicate glasses are highly promising candidate materials for orthobiologics and alternate applications requiring delivery of biologic payloads.

Hydroxyapatite powder was mixed into photosensitive resin to form complex shape scaffold using SLA-3D printing technology, and then the final entity was obtained successively by debinding and sintering. It is crucial to confirm whether the prepared hydroxyapatite scaffold have the toxic effects after our designed printing, debinding, and sintering processes because the photosensitive resin in the starting printing paste is poisonous to cells. To investigate these issues in details, thermogravimetric analysis (TG), differential scanning calorimetry (DSC), in vitro cytotoxicity test, and implantation pre-experiment in the rabbit parietal were performed, aiming to develop the SLA-3D prepared hydroxyapatite scaffold. Through thermal analysis, it was proved that photosensitive resin would be completely pyrolyzed at temperature ranging from 350 °C to 580 °C, corresponding to a secondary chemical reaction mechanism. Combined with cytotoxicity test results, it is unquestionable that the toxic substances would be totally decomposed after debinding process and a good biocompatible HAP samples could be obtained. The finally prepared HAP samples with micro-holes showed good biosafety in pre-experiment of the rabbit parietal implantation., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

To evaluate the bioactivity and the cytocompatibility of experimental Bioglass-reinforced polyethylene-based root-canal filling materials. The thermal properties of the experimental materials were also evaluated using differential scanning calorimetry, while their radiopacity was assessed using a grey-scale value (GSV) aluminium step wedge and a phosphor plate digital system. Bioglass 45S5 (BAG), polyethylene and Strontium oxide (SrO) were used to create tailored composite fibres. The filler distribution within the composites was assessed using SEM, while their bioactivity was evaluated through infrared spectroscopy (FTIR) after storage in simulated body fluid (SBF). The radiopacity of the composite fibres and their thermal properties were determined using differential scanning calorimetry (DSC). The cytocompatibility of the experimental composites used in this study was assessed using human osteoblasts and statistically analysed using the Pairwise t-test (p<0.05). Bioglass and SrO fillers were well distributed within the resin matrix and increased both the thermal properties and the radiopacity of the polyethylene matrix. The FTIR showed a clear formation of calcium-phosphates, while, MTT and AlamrBlue tests demonstrated no deleterious effects on the metabolic activity of the osteoblast-like cells. BAG-reinforced polyethylene composites may be suitable as obturation materials for endodontic treatment. Since their low melting temperature, such innovative composites may be easily removed in case of root canal retreatment. Moreover, their biocompatibility and bioactivity may benefit proliferation of human osteoblast cells at the periapical area of the root., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

The present study reports on the influence of partial replacement of MgO by ZnO on the structure, crystallisation behaviour and bioactivity of alkali-free bioactive glass-ceramics (GCs). A series of glass compositions (mol%): 36.07 CaO-(19.24-x) MgO-x ZnO-5.61 P2O5-38.49 SiO2-0.59 CaF2 (x=2-10) have been synthesised by melt-quench technique. The structural changes were investigated by solid-state magic angle spinning nuclear magnetic resonance (MAS-NMR), X-ray diffraction and differential thermal analysis. The sintering and crystallisation behaviours of glass powders were studied by hot-stage microscopy and differential thermal analysis, respectively. All the glass compositions exhibited good densification ability resulting in well sintered and mechanically strong GCs. The crystallisation and mechanical behaviour were studied under non-isothermal heating conditions at 850 °C for 1h. Diopside was the primary crystalline phase in all the GCs followed by fluorapatite and rankinite as secondary phases. Another phase named petedunnite was identified in GCs with ZnO content >4 mol. The proliferation of mesenchymal stem cells (MSCs) and their alkaline phosphatase activity (ALP) on GCs was revealed to be Zn-dose dependent with the highest performance being observed for 4 mol% ZnO., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Exploring new applications of negative thermal expansion (NTE) materials is a recent research hotspot. In this work, the IV A element Sn was used to tailor the thermal expansion and dielectric properties of NTE material ZrMgMo 3 O 12 , and the samples Zr 1–x Sn x MgMo 3 O 12 (x = 0.05, 0.10, 0.15, 0.20, 0.25) can be used in the field of high-frequency dielectric ceramics. Both the substitution amount of Sn and sintering temperature have a certain effect on the properties of Zr 1-x Sn x MgMo 3 O 12. The coefficients of thermal expansion (CTE) can be adjusted between near zero thermal expansion (ZTE) (−0.24 × 10−6/K−1) and NTE (−8.16 × 10−6/K−1) and become larger toward negative as the amount of Sn increased under the same sintering temperature. The dielectric constants of Zr 1-x Sn x MgMo 3 O 12 can be adjusted in the range of 130∼155, which are about 25 times than ZrMgMo 3 O 12. The dissipation factors of Zr 1-x Sn x MgMo 3 O 12 were adjustable between 4.37 × 10−4 and 5.54 × 10−4, meeting the application requirements of high-frequency dielectric ceramics. This research shows that Sn can adjust the thermal expansion properties and significantly improves the dielectric properties of ZrMgMo 3 O 12 , so that Zr 1-x Sn x MgMo 3 O 12 materials have high value in the field of high-frequency dielectric ceramics. [ABSTRACT FROM AUTHOR]

Thermal camouflage technology can effectively hide an object by lowering its infrared emissivity and reducing its surface temperature. So far, it has been a challenge to realize thermal camouflage at high-temperatures with a single material. Here, we report a Ti 3 AlC 2 MAX phase material that exhibits excellent thermal camouflage properties from room temperature to 500 °C, and maintains a low emissivity of 0.25 at 500 °C, which is difficult to achieve for most metals due to the rapid increase in emissivity caused by oxidation. The thermal camouflage mechanism of Ti 3 AlC 2 was analyzed on the basis of experimental results and first-principles calculations, providing a feasible approach to select other MAX phases (such as Ti 3 SiC 2 , Cr 2 AlC, and Ti 2 AlC) with attractive thermal camouflage performance. Ti 3 AlC 2 and other MAX phases are promising candidates for thermal camouflage applications due to their low emissivity, high-temperature stability, good oxidation resistance and ease of fabrication. [ABSTRACT FROM AUTHOR]

This work investigates the behavior and properties of corundum and mullite ceramics at high temperatures and during very long exposures in a controlled atmosphere. The motivation of the work lies primarily in advanced applications in nuclear energy technology, specifically in the search for materials for helium-cooled reactors of the 4th generation. The studied ceramic samples Al63, Al70, Al76, Al96, Al100, where the number indicates the mass percentage of Al 2 O 3 , were exposed for 1000 h at a temperature of 900 °C in gaseous atmospheres of helium, nitrogen and air. The properties of the exposed and unexposed samples were evaluated by measuring the bending strength at room temperature (CMOR), hot modulus of rupture at high temperature (HMOR), and isothermal creep, BET method, and using electron microscopy. The color changes induced by the reducing atmosphere and temperature were also interpreted using a simple thermochemical model. The CMOR measurement results show that all ceramic samples do not significantly change their properties due to long-term exposure. The detected deviations in the exposed samples from the unexposed ones can be considered random caused by the inherent heterogeneous structure. A similar conclusion also applies in the case of the HMOR measurement results, except for the results for the Al63 sample, where the drop in the strength of the exposed samples by approx. 37 MPa (20 %) may be related with the highest proportion of polyvalent oxide admixtures of all studied ceramics, i.e. 1.01 wt % Fe 2 O 3 and 0.52 wt % TiO 2. The change in color indicates that the iron and titanium present are being reduced. However, none of the conducted experiments indicate that changes in the redox state associated with the formation of oxygen vacancies would significantly reduce strength at high temperatures or increase creep in mullite ceramics. [ABSTRACT FROM AUTHOR]

The concurrent enhancement of toughness, electrical conductivity, and thermal stability in polycrystalline diamond composites represents a formidable challenge. Here, a novel diamond-TiC composites (referred to as DTC) with high fracture toughness and conductivity were synthesized through a high-temperature and high-pressure reaction sintering process utilizing two precursors: diamond mixtures containing TiH 2 and Ti-coated diamonds. On the one hand, the inherent bonding and encasing of TiC onto the diamond matrix form a heterogeneous structure, providing high strength and excellent fracture toughness up to 11.6 MPa·m1/2. On the other hand, the established oxygen barrier and current pathway offer a thermal stability of 765 °C and high conductivity up to 837 S·m−1. Remarkably, this rare combination of mechanical, electrical, and thermal properties has been realized within a single material under relatively moderate sintering conditions, thus positioning diamond-TiC composites as a promising ceramic for electrical applications in high-stress environments. [ABSTRACT FROM AUTHOR]

Si3N4 ceramics with high mechanical properties and thermal conductivity, exhibiting fine and bimodal microstructure, were prepared by adjusting the Er2O3/MgO ratio and hot‐pressing sintering at 1800°C for 4 h. The microstructure, grain distribution, lattice oxygen content, mechanical properties, and crack propagation process of the sintered bulk samples were systematically investigated. It was found that a low Er2O3/MgO ratio contributed to the densification of Si3N4 ceramics, whereas a high Er2O3/MgO ratio favored the grain growth of Si3N4 ceramics. In this research, the grain size distribution and average diameters as well as their impact on mechanical properties were examined. When the ratio of Er2O3/MgO was 3:1, Si3N4 had a larger average diameter and higher thermal conductivity, but the mechanical properties were somewhat reduced. When the ratio of Er2O3/MgO was 2:2, the sample displayed enhanced mechanical performance, which can be explained by the formation of a bimodal structure. The research indicates that it is feasible to control the microstructure and optimize the mechanical properties of Si3N4 ceramics by tailoring the sintering additives. [ABSTRACT FROM AUTHOR]

Porous SiC ceramics with three different pore sizes (∼7, ∼45, and ∼98 μm) and two different porosities (∼54% and ∼63%) were prepared to investigate the effects of pore size on electrical and thermal properties of the porous ceramics. With an increase in pore size from ∼7 to ∼98 μm at the same porosity (∼54%), the electrical and thermal conductivities of the porous ceramics increased from ∼1.01 to ∼2.30 Ω−1·cm−1 and ∼14.3 to ∼26.2 W·m−1K−1, respectively. Similar trends have been obtained in the ceramics with ∼63% porosity. The porous SiC ceramic with larger pore size has smaller pore/strut interface area at the same porosity, which leads to less carrier scattering and phonon‐pore scattering at the pore/strut interfaces, resulting in higher electrical and thermal conductivities, respectively. These results suggest that the electrical and thermal properties of porous SiC ceramics can be successfully tuned by adjusting the pore size and porosity depending on the application. [ABSTRACT FROM AUTHOR]

In the thermal protection system of spacecraft, the bolts connecting the ceramic to the internal superalloy need to have low thermal conductivity and high strength. Two dense high entropy fluorite oxides (Zr 1/7 Hf 1/7 Ce 1/7 Y 2/7 La 2/7)O 2-δ (ZHCYL) and (Zr 1/8 Hf 1/8 Ce 1/8 Y 1/4 La 1/4 Pr 1/8)O 2-δ (ZHCYLP) were designed and synthesized by using the synergistic effect of plasma-assisted ball milling and spark plasma sintering(SPS). Through the synergistic effect of lattice distortion and oxygen vacancy guided by entropy regulation, ZHCYLP synthesized in this study has lower thermal conductivity(1.13 W·m−1·K−1), higher high temperature strength(192 MPa at 1000 °C) and high temperature phase stability up to 1600 °C than 8YSZ ceramics. The thermo-mechanical coupling finite element analysis results of high temperature bending test show that the variation trend of the maximum stress value of the sample is consistent with the experimental results. This shows that the mechanical and thermal properties of high entropy oxides can predict the variation trend of the maximum stress value in high temperature bending tests. It opens up a new way for designing and synthesizing high entropy oxide materials with low thermal conductivity and high strength which can be applied in the field of heat protection and load bearing. [ABSTRACT FROM AUTHOR]

Ceramic fibers are an important thermal insulation material that are not only widely used in extreme conditions, but also play an important role in energy conservation and energy efficiency for sustainable development. However, the practical application of conventional ceramic fibers has a high thermal conductivity in high-temperature environments, which hinders their widespread application. Here, a novel lamellar structured porous SiTiOC/C composite ceramic materials was designed and prepared with excellent thermal insulating properties. The unique microstructure endowed the porous SiTiOC/C composite ceramic materials with a high IR refractive index (93.81%) and an ultra-low thermal conductivity (0.0562 W·m−1 K−1 at 600 ℃). In addition, the porous SiTiOC/C composite ceramic materials not only exhibited excellent mechanical properties (4.46 MPa at 800 ℃), but also demonstrated impressive oxidation resistance and thermal stability. In summary, the proposed porous SiTiOC/C composite ceramic materials provide a reference for the development of high-temperature insulation with good mechanical properties. [ABSTRACT FROM AUTHOR]

Ceramic aerogels are promising candidates for high-temperature thermal resistance and thermal insulation materials. However, their application can be restricted by their brittleness when exposed to harsh conditions. Herein, this study has developed a novel synthesis process based on a sol-gel method and carbothermal reduction-nitridation to produce a porous TiN composite aerogel from an organic/inorganic hybrid. The resulting TiN displays a polyhedral particle size of around 30–60 nm with nanoscale pores. In addition, the TiN aerogel demonstrates a high BET-specific surface area of 653.42 m2/g and a very low thermal conductivity of 0.046 W/(m·K). Furthermore, the TiN aerogel composite displays a good thermal difference with no shrinkage and cracks of the morphology during the butane blazing torch at 1300 °C for 10 min under air environment, demonstrating its excellent thermal insulation property and anti-oxidation characteristics. The gas-solid reaction mechanism of TiN aerogel based on the Gibbs free energy calculations is also proposed. [ABSTRACT FROM AUTHOR]

Alumina‐based porous ceramics were fabricated via the starch consolidation casting route, using titanium oxide as a sintering additive. Alumina‐titania‐starch slurries with starch contents of 2.5, 5, 7.5, and 10 wt% relative to the alumina‐titania system were prepared. Titania was added to the slurries in proportions of 0, 1, 3, and 5 wt%, relative to alumina. The effects of starch and titania contents in the green bodies on the linear and volumetric shrinkage, as well as the total and open porosities of the sintered alumina product, were investigated. The effect of titania addition on mechanical, electrical, and thermal properties of the obtained porous alumina ceramics was studied. Microstructure and pores morphology were characterized by SEM. The alumina‐based ceramics obtained had external porosities that varied between 54 and 76 vol%. Thermal conductivities as low as 0.06–0.1 W/m.K were achieved and the volume electrical resistivity ranged from 3.6 to 600 GΩ·m, while compressive strengths up to 2.8 MPa for a titania ratio of 1 wt% were attained. [ABSTRACT FROM AUTHOR]

(KMg)3+ co-doped Sc 2 W 3 O 12 ceramics have been prepared via co-precipitation method. Effects of (KMg)3+ co-doping amount and sintering temperature on the phase constitution, microstructure, morphology, and negative thermal expansion (NTE) performance of K x Mg x Sc 2- x W 3 O 12 (0 ≤ x ≤ 1.25) ceramics were studied. Results indicate that: Sc3+ cations can be substituted by (KMg)3+ dual-cations and a composition-induced structural phase transition was observed in K x Mg x Sc 2- x W 3 O 12. For x ≤ 0.25, orthorhombic Sc 2 W 3 O 12 gradually changed into hexagonal K x Mg x Sc 2- x W 3 O 12 and coexisted. Single phase K x Mg x Sc 2- x W 3 O 12 with hexagonal symmetry can be prepared for 0.25 < x ≤ 1. When x ≥ 1.25, (KMg)3+ substitution reaches its solid solution limit in Sc 2 W 3 O 12 , and impurity MgWO 4 formed in the samples. As co-doping amount x increased, the NTE performance of the K x Mg x Sc 2- x W 3 O 12 (0 ≤ x ≤ 1) ceramics gradually enhanced. The coefficient of thermal expansion (CTE) of K x Mg x Sc 2- x W 3 O 12 (0 ≤ x ≤ 1) ceramics enhanced from −2.14 × 10−6 °C−1 to −19.68 × 10−6 °C−1 in 30–700 °C. With the increase of sintering temperature from 800 to 1100 °C, the grains grew up and the density of the K 0.75 Mg 0.75 Sc 1.25 W 3 O 12 ceramics increased as well, and the NTE performance was also improved. The linear CTE of K 0.75 Mg 0.75 Sc 1.25 W 3 O 12 ceramics enhances from −2.15 × 10−6 °C−1 to −14.70 × 10−6 °C−1 in 30–700 °C. [ABSTRACT FROM AUTHOR]

Lightweight phenolic matrix composites are highly potential in ablative thermal protective materials for future aerospace vehicles, and hybrid modification is considered as one of effective ways to improve the oxidation and ablation resistance of phenolic matrix. Herein, the co-continuous silica zirconium hybrid phenolic resin (SZRx) was synthesized, which can be used to prepare lightweight ablation resistant aerogel composites by the sol-gel method. The SZRx aerogel showed stable porous structure and excellent hydrophobicity, and the silicon zirconium hybrid greatly improved the high temperature carbon residue and oxidation resistance of phenolic resin. The SZRx aerogel composites also possessed excellent integrated characteristics of heat protection and insulation, with a linear ablation rate as low as 0.032 mm/s and a back temperature below 200 °C. The synergistic effect of silicon and zirconium formed the multiphase ceramic layer (C, SiO 2 , SiC and ZrO 2) with the sea-island-like structure on the surface of the composite material, which can effectively resist high-temperature ablation and aerodynamic exfoliation. This can indicate that silicon zirconium dual element hybrid phenolic resin is the highly competitive matrix for lightweight and ablation resistant composite materials. [Display omitted] [ABSTRACT FROM AUTHOR]

In pursuing enhanced performance for electronic applications, we synthesized ferroelectric materials, specifically Ba(1-x)Nd2x/3TiO3 (BNdTx) nanoceramics, utilizing solid-state reaction techniques coupled with microwave heating treatment. Our investigation involved varying Nd3+-doping levels (x = 0%, 2%, 4%, and 8%) to tailor the material's properties. XRD analysis confirmed the presence of a single-phase tetragonal perovskite structure (space group P4mm). A comprehensive examination of the partial density of states for both undoped and Nd3+-doped BaTiO3 was undertaken to discern the impact of Nd3+-doping on the energy bands. Microscopic analysis revealed the presence of pores in the samples, accompanied by a reduction in grain size with increasing Nd3+ content. The introduction of Nd3+ induced a shift in the Curie temperature (TC) towards room temperature. Simultaneously, the dielectric characteristics exhibited a consistent value above 1900, with a low loss of less than 5% observed across a range of temperatures (30–100 °C). Notably, the sample with x = 4% demonstrated thermally stable dielectric properties, suggesting its potential suitability as a material for Multilayer Ceramic Capacitor (MLCC) applications. Integrating microwave sintering and ball milling techniques is a significant development in advanced materials engineering, specifically in producing Multi-Layer Ceramic Capacitors (MLCC). The practical implementation of these novel methodologies is essential in decreasing particle size, which is a critical determinant in improving thermal stability. Ball milling further refines the particle size distribution, whereas microwave sintering guarantees a more uniform and fine-grained microstructure through its rapid and effective heating capabilities. The capacitors acquire enhanced thermal stability and a more refined material granularity through this synergistic combination. By achieving a more uniform and compact ceramic structure, these processes result in a finer particle size, enhancing the overall performance and dependability of MLCC capacitors. The increasing need for miniaturized and high-performance electronic components has focused on utilizing microwave sintering and ball milling. These processes are at the forefront of technological advancements in the pursuit of improved thermal properties and increased efficiency in manufacturing MLCC capacitors. [ABSTRACT FROM AUTHOR]

Ceramic thermal barrier coatings (TBCs) with high toughness and low thermal conductivity are important for developing aero engines with high thrust‐to‐weight ratio and thermal efficiency. In this work, the properties of tantalate Y1/6Yb5/6TaO4 (YYT) were optimized by introducing 8 wt.% yttria‐stabilized zirconia (8YSZ), synthesized using spark plasma sintering, as a second‐phase ceramic. The highest toughness (3.57 MPa m1/2) of the YYT/8YSZ composite ceramics was due to multiple toughening mechanisms. The underlying mechanisms of these processes were revealed based on the microstructures and residual stress of the YYT/8YSZ composite ceramics. A shift from an intergranular fracture to a transgranular fracture was caused by the difference between soft‐grain YYT and hard‐grain 8YSZ, which consumed the fracture energy. Furthermore, the formation of microcracks, crack deflection, bridging, and branching were analyzed based on the differences in Young's moduli and thermal expansion coefficients of YYT and 8YSZ. Internal defects and weak connections between the YYT and 8YSZ grains reduced the thermal conductivity of the composites until it reached its lowest value at 1.4 W m−1 K−1. The studied toughening mechanisms could be applied to various composites. Moreover, herein, we provide a new strategy to design and synthesize TBCs with enhanced performance. [ABSTRACT FROM AUTHOR]

In this study, a highly dense GdB 6 bulk ceramic material was fabricated using one-step in-situ reaction spark plasma sintering technology. The sample with a relative density of 96.7 % and a purity of 96.9 wt% was successfully obtained by sintering at 1800 °C for 30 min under a uniaxial pressure of 50 MPa. The Vickers hardness, elastic modulus and fracture toughness of the as-obtained GdB 6 bulk ceramics were 18.9 GPa, 209 GPa and 1.6 MPa·m1/2, respectively. The thermal conductivity of GdB 6 at room temperature was 28.68 W·m−1·K−1, 70 % of which was mainly attributed to phonon vibration, while the remaining 30 % to the electrical thermal conductivity. In addition, the as-obtained GdB 6 ceramics showed no phase transformation after heat treatment at a relatively high temperature of 2100 °C for 20 min in Ar atmosphere. The highly covalent octahedral boron framework played a critical role in maintaining the phase stability of the GdB 6 crystal lattice. This suggested that GdB 6 ceramics could be used as potential ultra-high temperature ceramics for aerospace applications and high-power vacuum electronic devices operated at high temperatures. [ABSTRACT FROM AUTHOR]

Rare earth compounds (RE 2 O 3), typically Eu 2 O 3 and Gd 2 O 3 , are considered as absorbing materials due to their long chain neutron absorbing ability and high efficiency of neutron absorption. In this paper, a specifically designed x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 (x = 0.6, 0.7, 0.8, 0.85) composite ceramics with excellent thermal properties were synthesized through direct thermal decomposition reactions followed a high-temperature sintering method under vacuum conditions. X-ray diffraction (XRD) and Raman spectroscopy analysis indicated that the obtained ceramics consisted of monoclinic Eu 2 O 3 and fluorite Gd 2 Zr 2 O 7 phases. The hardness of x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 ceramics (x = 0.8, 0.85) have no significantly changes in the test temperature range (25–350 °C). The thermal expansion coefficients (TECs) (7.3–10 ×10-6 K-1) are lower than Dy 2 TiO 5 (9.3–10.4 ×10-6 K-1), and the thermal expansion rate changes linearly with the increase of temperature, which indicates that the x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 ceramics exhibit excellent high temperature phase stability. Furthermore, the range of thermal conductivities is from 0.96 W·m-1·K-1 to 2.02 W·m-1·K-1 (25–800 °C), which is higher than Dy 2 TiO 5 (0.27–0.55 W/m·K, 220–650 °C). Compared with the state-of-art Dy 2 TiO 5 ceramics, x Eu 2 O 3 -(1-x)Gd 2 Zr 2 O 7 have superior thermal properties and are therefore expected to be the next generational of neutron absorbent materials used in ash rod. [ABSTRACT FROM AUTHOR]

This study utilizes modulation of ionic disorder and electronegativity differences for targeted component design of high-entropy ceramic compositions. A series of novel multicomponent ceramics with the general formula (LaGdYSm) x 2 Yb x 1 Zr 2 O 7 (x 1 +4x 2 = 2, x 1 = 0.6,0.4,0.2,0) were prepared by solid-state reaction. The evolution patterns of their microstructures were analyzed using XRD and TEM, and the anti-sintering ability and thermophysical properties were evaluated. The results confirm that the multicomponent ceramics gradually transform from the coexistence of pyrochlore/fluorite dual-phase structure to pyrochlore structure with the tuning of the size disorder degree. After 50h of exposure to air at 1500 °C, the ceramics retained excellent phase stability. Segregation of La and Yb elements with large differences in radius size occurs, forming a mixture of the La-rich pyrochlore and the Yb-rich fluorite phases. The specimen with the maximum size disorder exhibits the lowest grain growth rate and the greatest thermal insulation properties. Large lattice distortions and sluggish diffusion effects are responsible for the mutual inhibition of grain growth in the two-phase coexistence zone. The thermal insulation properties of the ceramics show well correlated with the degree of the size disorder, further validating the effectiveness of the component design. Meanwhile, the thermal expansion coefficients of prepared ceramic can reach 11.49 × ∼11.58 × 10−6 K−1 at 1000–1100 °C. The customization principles used in this work fill a gap in the compositional design methodology for multicomponent lanthanum zirconate-based high-entropy ceramics. It is essential for developing rare-earth zirconates with tunable thermophysical properties in the area of thermal barrier coatings. [ABSTRACT FROM AUTHOR]

Zirconium carbide (ZrC) ceramics have a high melting point, low neutron absorption cross section, and excellent resistance to the impact of fission products and are considered to be one of the best candidate materials for fourth-generation nuclear energy systems. ZrC ceramics with a high relative density of 99.1% were successfully prepared via pressureless sintering using a small amount of MoSi2 as an additive. The influence of the MoSi2 content on the densification behavior, microstructure, mechanical properties, and thermal properties of ZrC ceramics was systematically investigated. The results show that the densification of ZrC was significantly enhanced by the introduction of MoSi2 due to the formation of a liquid phase during sintering. In addition, the ZrC grains were refined due to the pinning effect of the generated silicon carbide. The flexural strength and Vickers hardness of ZrC ceramics with 2.5 vol% MoSi2 sintered at 1850 °C were 408 ± 12 MPa and 17.1 GPa, respectively, which were approximately 30% and 10% higher compared to the samples without the addition of MoSi2. The improved mechanical properties were mainly attributed to the high relative density (99.1%) and refined microstructure. [ABSTRACT FROM AUTHOR]

Al 2 O 3 /B 2 O 3 powder mixtures prepared at various ratios from 10.7 to 54.1 wt% B 2 O 3 were used to synthesize Al 18 B 4 O 33 powders by solid state calcination at 1300 °C for 1 h. Al 18 B 4 O 33 formation was completed at 44 wt% B 2 O 3 instead of stoichiometric ratio of 13.17 wt% B 2 O 3. In other words, B 2 O 3 -rich liquid phase accelerated Al 18 B 4 O 33 crystallization. Al 18 B 4 O 33 particles were not acicular in shape when first formed, but they were fully acicular for the 44 wt% and the 54.1 wt% B 2 O 3 mixtures. Anorthite-based glass and CaO were selected to induce liquid phase sintering. CaO considerably improved densification to 95.4 % relative density at 1350 °C. Both glass and mullite also enhanced densification to 94.8 %. Epitaxial nucleation of mullite on Al 18 B 4 O 33 particles resulted in a solid solution as well. Dielectric, mechanical and thermal properties of the samples were investigated and evaluated for possible applications. [ABSTRACT FROM AUTHOR]

An additively manufactured reaction‐bonded silicon carbide ceramic composite is fabricated using a bimodal powder feedstock and the binder‐jetting printing technique. On fabricating, the ceramic is investigated to report its composition, mechanical, and thermal properties at room temperature and high temperatures (up to 750∘C$^{\circ }C$). The ceramic has a density of 2.76 g/cc, and shows a hardness of 21.74 GPa, and a flexure strength of 207.5 MPa at room temperature. The mechanical property of flexure strength is used to estimate its failure probability under applied stress, using a Weibull distribution. The mechanical properties and failure probabilities are compared with those of conventionally fabricated reaction‐bonded silicon carbide ceramics reported in the literature. These ceramics were fabricated using methods such as slip‐casting, compacting, and tape‐casting. The comparison is used to elucidate the advantages and areas of improvement of the present additive manufacturing technique for reaction‐bonded ceramics. [ABSTRACT FROM AUTHOR]

Recently, CaO‐doped (≤4 mol.%) tetragonal zirconia (CaSZ) ceramic was recommended as a potential alternative to yttria‐stabilized ZrO2 (YSZ). Here, we investigate the limits of starting particle sizes on the stability of tetragonal (t) phase and other associated benefits on measured properties. Synthesized CaSZ powders calcined with different temperatures were used as a mono‐sized or mixed (i.e., two different calcination temperatures) batch fraction for making dense CaSZ ceramic. The mixed‐batch powders were found to be far more efficient in stabilizing the t‐phase in ceramic. Compared to YSZ, CaSZ recorded remarkable enhancement in toughness (up to 8.3 MPa m$\sqrt {\mathrm{m}} $). Contrary to YSZ, CaSZ ceramic demonstrated outstanding thermal stability. [ABSTRACT FROM AUTHOR]

High-entropy carbide ceramic materials exhibited excellent thermal and mechanical properties, making them highly sought after in high-temperature applications. However, the oxidation resistance of high-entropy carbide ceramic needed to be further improved. This work unraveled the oxidation behavior and mechanism of high-entropy carbide ceramic by introducing the Cr 3 C 2. The results indicated that the oxidation rate of (TiZrTaNbCr)C initially decreased with temperature up to 900 °C, followed by an increased with further temperature rise up to 1100 °C. At 800 and 900 °C, the parabolic oxidation rate constants were 0.70 and 0.17 mg2cm−4min−1, respectively. And the minimum thickness of oxidized layer was 60 µm at 900 °C for 120 min. This unusual phenomenon suggested the formation of different oxidation products. Specifically, the CrNbO 4 and Nb 2 Zr 6 O 17 oxide layer were formed at 900 °C, leading to an increased resistance to oxygen diffusion. Subsequently, loose oxidation products of Nb 2 O 5 were formed after 1000 °C, hindering the oxidation resistance. In the current study on oxidation resistance of high entropy carbides, this work showed a competitive performance. Overall, this study illustrated the oxidation mechanism and behavior of (TiZrTaNbCr)C and proposed a new avenue for the design of high-entropy ceramic components. [ABSTRACT FROM AUTHOR]

The (1−x)CaO-B2O3-SiO2(CBS)/xMg2SiO4 composites were prepared and the influence of CBS crystallizable glass content on the sintering properties, dielectric properties, and thermal properties of the composites were investigated. The primary crystal phases in the CBS/Mg2SiO4 composites were CaMgSi2O6 and CaB2O4. An appropriate amount of Mg2SiO4 reduced the crystallization temperature of the composite. For x = 0.30, a sintering temperature of 890°C with a holding time of 60 min resulted in a bulk density of 2.645 g/cm3, dielectric constant of 6.6, and dielectric loss of 2.54 × 10−3 at 10 kHz. Prolonged holding time promotes grain growth; when extended from 60 min to 180 min for x = 0.30, the permittivity increased from 6.5 to 6.6 and Q×f increased from 10,100 GHz to 15,700 GHz when x = 0.30 at 13 GHz. The CTE of 70 wt.% CBS + 30 wt.% Mg2SiO4 composite was 9.5 ppm/°C, which approached the value of a circuit board for a ceramic ball grid array package (CBGA). [ABSTRACT FROM AUTHOR]

The mechanical and thermal properties of ZrC x are strongly dependent on the composition and microstructure. In the present study, densified ZrC x (x = 0.5, 0.7 and 1.0) with relative density in the range of 99.2–99.7% have been prepared by a combination of spark plasma sintering (SPS) and vacuum arc melting (VAM). Both the Young's modulus and Vickers hardness monotonically increase with increasing C/Zr ratio. The maximum Young's modulus and Vickers hardness values of 488.1 ± 13.4 GPa and 28.8 ± 1.7 GPa, respectively, for dense ZrC have been obtained. With increasing the C/Zr ratio, the thermal conductivity of ZrC x increases. The thermal conductivity ZrC ranged from 25.17 W/m/K to 43.85 W/m/K from ambient to 1200 °C. Owing to the higher density of ZrC x , the present thermal conductivities and Young's modulus of ZrC x are higher than those of the previous studies. The present results are beneficial to design and preparation of ZrC x ceramics. [ABSTRACT FROM AUTHOR]

A novel NbSi 2 /Nb 2 O 5 -SiO 2 /MoSi 2 multilayer thermal protection ceramic coating is designed and fabricated via halide-activated pack cementation and liquid-plasma-assisted particle deposition and sintering technology, endowing the coating with multiple high-temperature protective properties. The incorporation of MoSi 2 nanoparticles not only gives superior high-temperature oxidation resistance/hot corrosion resistance of coating by forming a dense SiO 2 barrier layer, but also promotes passive radiative heat dissipation. When NbSi 2 /Nb 2 O 5 -SiO 2 /MoSi 2 coating was prolonged exposure to air at 1250 °C for 50 h of oxidation and at 900 °C for 100 h of corrosion, the mass gains are only 0.37 mg/cm2 and − 0.52 mg/cm2, respectively. The multilayer coating exhibits enhanced emissivity (>0.88) over the thermal infrared range of 3–20 µm, due to the lattice vibrational absorption-matching synergy of Nb 2 O 5 , SiO 2 , and MoSi 2 , as well as the mutual doping of SiO 2 /Nb 2 O 5 , mismatch of atoms at the interface, and a high degree of lattice distortion within the coating. [ABSTRACT FROM AUTHOR]

Reduced graphene oxide, due to its structure, exhibits anisotropic properties, which are particularly evident in electrical and thermal conductivity. This study focuses on examining the influence of reduced graphene oxide in silicon carbide on these properties in directions perpendicular and parallel to the direction of the aligned rGO flakes in produced composites. Reduced graphene oxide is characterized by very high in-plane thermal and electrical conductivity. It was observed that the addition of rGO increases thermal conductivity from 64 W/mK (reference sample) up to 98 W/mK for a SiC–3 wt.% rGO composite in the direction parallel to the rGO flakes. In the perpendicular direction, the values were slightly lower, reaching up to 84 W/mK. The difference observed in electrical conductivity values is more significant and is 1–2 orders of magnitude higher for the flakes' alignment direction. The measured electrical conductivity increased from 1.2710−8 S/m for the reference SiC sinter up to 1.55 × 10−5 S/m and 1.2410−4 S/m for the composites with 3 wt.% rGO for the perpendicular and parallel directions, respectively. This represents an enhancement of four orders of magnitude, with a clearly visible influence of the anisotropy of the rGO. The composite's enhanced electrical and thermal conductivity make it particularly attractive for electronic devices and high-power applications. [ABSTRACT FROM AUTHOR]

Polycrystalline samples of (1-x)K 0.5 Bi 0.5 TiO 3 - xBaTiO 3 [(1-x)KBT - xBT] were synthesized using a solid-state reaction pathway. X-ray diffraction analysis confirmed the presence of a single-phase perovskite structure. To explore relaxation and conduction mechanisms, complex impedance spectroscopy was employed. Reduction in Curie temperature was observed as BT content increased. The grain and grain boundary contributions to relaxation was examined through complex impedance and modulus plots and quantified via fitting experimental data to an equivalent circuit model. Examination of the Complex impedance spectra uncovered the existence of dielectric relaxation characteristic of a non-Debye nature. Furthermore, the activation energy determined suggests commonalities in governing the conduction and relaxation processes in relation to temperature-dependent conductivity and relaxation time. A negative temperature coefficient of resistance behaviour was obtained from the temperature-dependent conductive study. Dielectric spectra revealed that these ceramic capacitors are useful in reduction of signal interference, signal attenuation and impedance matching circuits applications. [ABSTRACT FROM AUTHOR]

The chemical corrosion resistance properties of newly developed oxide (mullite-, cordierite)-bonded SiC ceramics prepared using mixture of waste fly ash and metal oxide additives were investigated in environments containing Na2SO4 at temperature 1000 °C for 8 h. The thermal shock resistance to cooling were evaluated as a function of quenching cycles. The changes in weight, flexural strength, and morphology due to thermal and chemical corrosion were examined. The mechanisms of flexural strength degradation due to chemical and thermal corrosion were analyzed, and the results were compared with literature data. In the hot corrosion by Na2SO4, the cordierite component was severely attacked in the cordierite-bonded SiC ceramics resulted ~ 34% strength degradation after 8 h corrosion; on the contrary, mullite-bonded SiC ceramics exhibited ~ 4% improvement of flexural strength. The chemical and thermal shock resistance results suggest a potential advantage of porous SiC ceramics prepared using waste fly ash for several industrial applications. [ABSTRACT FROM AUTHOR]

Mullite fiber-based porous ceramics is one of the most commonly used high-temperature insulation materials. However, how to further reduce the thermal conductivity and improve the strength of such materials has been a challenge in the field of high-temperature insulation. In this paper, mullite micro/nano fiber-based porous ceramic was prepared by introducing mullite nanofibers into mullite microfiber-based porous ceramics and the effect of microfiber/nanofiber weight ratio on the samples properties were characterized and analyzed. Results showed that the compressive strength and high-temperature thermal insulation properties of the porous ceramics increased significantly with an increase in the nanofiber content. For the porous ceramics with similar density (about 0.50 g/cm3), the compressive strength of the sample with a microfibers/nanofibers weight ratio of 1:2 was 1.43 MPa, which was much higher than that of the porous ceramics prepared with only microfibers (0.26 MPa). Meanwhile, the backside thermal equilibrium temperature of the sample with a microfiber/nanofiber weight ratio of 1:2 at 900 °C environment was 355.8 °C, which was much lower than that of the porous ceramic prepared with only microfibers (476.5 °C). In addition, in order to investigate the temperature resistance of mullite micro/nano fiber-based porous ceramics, the sintering temperatures was increased from 1400 °C to 1500 °C. Results shows that the high-temperature thermal insulation performance of mullite micro/nano fiber-based porous ceramics with high mullite nanofiber content decays more seriously. The back-temperature test showed that the thermal equilibrium temperature of the samples with a mullite micron/nanofiber weight ratio of 1:1 in 900 °C environment increased rapidly from 386.3 °C to 454.2 °C when the sintering temperature was increased from 1400 °C to 1500 °C. The preparation of mullite micro/nanofiber-based porous ceramics provides a new strategy to improve the performance of fiber-based porous ceramics. [ABSTRACT FROM AUTHOR]

Ni-containing SiOC bulk ceramics have been prepared by spark plasma sintering at 1300 °C from polysiloxane at Ar atmosphere in the present work. The microstructure and properties of SiOC ceramics with different Ni content were studied. The resultant Ni-containing SiOC ceramics consists of in situ formed turbostractic layer carbon, CNTs (C nanotubes) and SiC crystals which dispersed in the SiOC matrix. With increasing content of Ni, the Ni-containing SiOC ceramics displayed less porosity. And the increasing Ni improved the mechanical, thermal and friction properties of SiOC ceramics. Ni-containing SiOC ceramics developed a carbon friction layer, which enhanced abrasion resistance to provide friction materials with stable friction coefficients and low abrasion values. A decrease in wear mass, from 2.06 to 0.18 mg was observed as the Ni content increasing from 0 to 2 wt%. The primary wear mechanisms of SiOC ceramics were recognized as abrasive wear, fatigue wear, and adhesion wear. [ABSTRACT FROM AUTHOR]

Entropy plays a crucial role in designing new functional materials or enhancing material performance. The design of high entropy ceramics (HECs) introduces a larger composition space, thus the understanding of the correlation between the composition, entropy effect, and the performance of HECs is becoming increasingly important. In this work, to pursue superior properties, a series of CeNbO 4 -based solid solution ceramics with a maximum of 9 species cations in a single sublattice were synthesized by using high entropy configuration strategy. The interaction of composition, size disorder, and configurational entropy on the properties of HECs was emphasized. The potential conflict between high resistivity and low material constant of thermosensitive ceramics was overcome and thus achieving excellent thermal sensitivity properties having an extremely wide temperature range from room temperature to 1623 K and long-term high-temperature stability. This will bring innovative prospects for the design and application of high-temperature functional ceramics. [ABSTRACT FROM AUTHOR]

Piezoelectric ceramics with excellent piezoelectric properties and a high Curie temperature are important for numerous electromechanical devices in a broad range of temperature environments. In this work, the relaxor ferroelectric Pb(Yb1/2Nb1/2)O3 end member was selected to be introduced into a BiScO3-PbTiO3 high-temperature piezoelectric ceramic to reduce the dielectric loss and improve the piezoelectric properties while slightly reducing the Curie temperature. The phase structure and dielectric, ferroelectric and piezoelectric properties of 0.025Pb(Yb1/2Nb1/2)O3-(0.975 − x)BiScO3-xPbTiO3 (0.60 ≤ x ≤ 0.63) ceramics were systematically analyzed, and the best electrical properties were observed in the morphotropic phase boundary region x = 0.61 with d33 = 370 pC/N, kp = 44%, Pr = 33.9 μC/cm2. Importantly, no significant depolarization was observed in the x = 0.61 ceramic from room temperature to 290 °C, demonstrating its good thermal stability and potential applications in a wide range of temperature environments. [ABSTRACT FROM AUTHOR]

In this study, according to the Dinger model, aqueous Si 3 N 4 slurries with a solid loading of 63 vol% and a viscosity lower than 1.0 Pa s were successfully prepared using two-grade Si 3 N 4 powders with D 50 = 7.2 μm and 9.4 μm as starting materials. These resulting slurries exhibited good rheological properties and suspension stability. Notably, the presence of β-Si 3 N 4 seeds existed in the starting materials effectively reduced the nucleation barrier by transforming homogeneous nucleation into heterogeneous nucleation. Consequently, it facilitated the reconstructive phase transformation of α-Si 3 N 4 to β-Si 3 N 4 , promoted the anisotropic growth of β-Si 3 N 4 nucleation, and resulted in the final formation of the bimodal microstructure. This unique microstructure significantly enhanced the mechanical properties of Si 3 N 4 ceramics, resulting in a high flexural strength of 1011.4 MPa and a fracture toughness of 14.8 MPa m1/2. These excellent properties were achieved through the combination of gelcasting and gas pressure sintering. Simultaneously, the Si 3 N 4 ceramics exhibited a low thermal conductivity of 47.7 W m−1 K−1, mainly owing to the low density of 95.3 %, the presence of low-thermal-conductivity silicate-based noncrystalline substances, and the possible existence of lattice oxygen in Si 3 N 4 crystals. [ABSTRACT FROM AUTHOR]

Lightweight ablative materials owing to their low density, high efficiency heat insulation and excellent designability, which are considered as the most promising candidate materials in the field of aerospace ablative thermal protection. In this work, a polycarbosilane (PCS) in-situ reinforced carbon felt/phenolic (PR/C f) aerogel composite is reported. The surface of aerogel and carbon fiber was coated with PCS protective layer by sol gel method and secondary vacuum impregnation process. The aerogel composite material possesses low density (0.264–0.307 g/cm3), hydrophobic, low thermal conductivity (0.121–0.178 W/(m·K)) and significant high compressive strength (12.89 MPa). When the oxygen acetylene flame with high heat flow density ablates for 20 s, it shows high efficiency in heat protection and insulation, and the linear ablation rate is as low as 0.089 mm/s. The PL/PR/C f aerogel composite shows competitive and broad application prospects in the field of ablation heat protection in the future. [ABSTRACT FROM AUTHOR]

Novel high-entropy (TiTaNbZrMo X)(CN) (x = 0, 5, 10, 15, and 20 at%) carbonitride ceramics were synthesised using the carbothermal reduction-nitridation and spark plasma sintering methods. The effects of Mo doping on the microstructure, mechanical properties, and thermal characteristics of these high-entropy ceramics were investigated. The increase in Mo contents caused increased grain size, uniform distribution of elements, improved Vickers hardness and fracture toughness, and reduced thermal conductivity at the same temperature. High-entropy (TiTaNbZrMo 0.2)(CN) ceramic displayed superior Vickers hardness of 21.41 GPa and fracture toughness of 4.34 MPa·m1/2, compared with 20.51 GPa and 3.94 MPa·m1/2 for (TiTaNbZr)(CN) ceramic, respectively. Density functional theory calculations indicated that adding Mo atoms promoted the hybridisation of metal and carbon elements, thereby preferentially enhancing electron filling in the bonding orbital due to high valence electrons. This, in turn, improved the mechanical properties of (TiTaNbZrMo x)(CN) ceramics. Additionally, the increased Mo contents strengthened covalent bonding and induced lattice distortion, reducing the thermal conductivity of high-entropy ceramics. [ABSTRACT FROM AUTHOR]

Textured process is considered an effective way to enhance the performance of piezoelectric ceramics. To obtain lead-free piezoelectric KNN-based ceramics with high performance, ⟨001⟩c-textured lead-free piezoelectric 0.915(K0.45Na0.5Li0.05)–0.075BaZrO3–0.01Bi0.5Na0.5TiO3 (KNLN–BZ–BNT) ceramics with the addition of 5 mol. % NaNbO3 templates were prepared, and the improved piezoelectric properties and thermal stability were expectedly achieved. For textured ceramics, the textured degree is one of the very important parameters and strongly depends on the amount of templates. Therefore, in this work, the effect of the amount of templates on the textured degree and electrical properties of ⟨001⟩c-textured KNLN–BZ–BNT ceramics were investigated in detail. It was found that the templates take a positive effect when the template amount is low, in which the textured degree and electrical properties increased with the amount of templates. In contrast, excess templates could induce a severe shift of stoichiometry within the textured ceramics, accompanied by degraded performances. As a result, for the ceramics with template amount less than 4 mol. %, enhanced textured degree and electrical properties were obtained. When the template amount exceeds 5 mol. %, the textured degree and electrical properties become degraded. The textured ceramic with the 4 mol. % template shows the highest textured degree of 93% and the highest piezoelectric constants of d33 = 360 pC/N and d 33 ∗ = 615 pm/V. Combining a vertical morphotropic phase boundary with an appropriate template amount of 4 mol. %, the ceramics exhibit superior thermal stability within the temperature range of 30–200 °C. [ABSTRACT FROM AUTHOR]

To date, the restricted capability to fabricate ceramics with independently tailored nano‐ and macroscopic features has hindered their implementation in a wide range of crucial technological areas, including aeronautics, defense, and microelectronics. In this study, a novel approach that combines self‐ and digital assembly to create polymer‐derived ceramics with highly controlled structures spanning from the nano‐ to macroscale is introduced. Polymerization‐induced microphase separation of a resin during digital light processing generates materials with nanoscale morphologies, with the distinct phases consisting of either a preceramic precursor or a sacrificial polymer. By precisely controlling the molecular weight of the sacrificial polymer, the domain size of the resulting material phases can be finely tuned. Pyrolysis of the printed objects yields ceramics with complex macroscale geometries and nanoscale porosity, which display excellent thermal and oxidation resistance, and morphology‐dependent thermal conduction properties. This method offers a valuable technological platform for the simplified fabrication of nanostructured ceramics with complex shapes. [ABSTRACT FROM AUTHOR]

To investigate the mechanism of the influence of the sintering additive ratio on the microstructure evolution of silicon nitride (Si 3 N 4) ceramics, Si 3 N 4 ceramics were prepared by gas pressure sintering using different ratios of Y 2 O 3 /MgSiN 2 as additives. Varying the ratio of Y 2 O 3 /MgSiN 2 changed the composition of the liquid phase, thereby affecting the densification process and phase transformation rate of Si 3 N 4 ceramics, and ultimately changing their microstructure. The reduction in the Y 2 O 3 /MgSiN 2 ratio raised the N/O and Si/O ratios in the system, which increased the liquid phase viscosity. The Si 3 N 4 grain distribution varied from "normal to bimodal". In the case of increasing the proportion of MgSiN 2 and prolonging the sintering time, more of the glass phase evaporated, which reduced the content of the low thermal conductivity phase and increased the continuity of Si 3 N 4 /Si 3 N 4. Therefore, Si 3 N 4 ceramics with 1 wt% Y 2 O 3 and 5 wt% MgSiN 2 exhibited excellent properties after sintering at 1900 °C for 12 h, with thermal conductivity, bending strength, and fracture toughness of 106.7 Wm−1K−1, 776 MPa, and 11.66 MPa m1/2, respectively. [ABSTRACT FROM AUTHOR]

In recent years, the MgO-Nd 2 Zr 2 O 7 composite ceramics inert matrix (IM) was proposed as a candidate for the transmutation of Pu and minor actinides (MA) in light water reactors (LWR) or accelerator driven sub-critical system (ADS). To take full advantage of the pyrochlore structure of Nd 2 Zr 2 O 7 to accommodate different types of MA and Pu, in this work, Y and Ce co-doped ω MgO-(1- ω)(Nd 1- x Y x) 2 (Zr 1- x Ce x) 2 O 7 (M-NYZC) composite ceramics used as a candidate IM for inert matrix fuel were prepared by solid-state one-step sintering method at 1500 °C for 3 h. The phase structure and microstructure of M-NYZC composite ceramics were characterized by XRD and SEM-EDS. Also, the thermal physical properties of M-NYZC composite ceramics including the thermal expansion coefficient and thermal conductivity were investigated systematically. Results from XRD and SEM-EDS showed that the magnesium oxide and NYZC pyrochlore solid solution are intermixed well with each other, and the M-NYZC samples present uniform element distribution with a grain size of about 1 μm. Also, the as-prepared samples possessed well densified microstructure, and the average relative density of all samples could exceed 95 %. Moreover, the thermal expansion coefficient and thermal conductivity of 0.5M-0.5NYZC (x = 0, 0.15, 0.2, 0.5, 0.9) samples were located in the range of 13.4 × 10-6–14.4 × 10-6 K-1 and 16.34–3.70 W·m-1·K-1 respectively. By comparison, the thermal physical properties of 0.5M-0.5NYZC samples are superior to that of traditional UO 2 and MOX fuels. It is suggested that the M-NYZC composite ceramics prepared in this study can meet the thermal physical performances of inert matrix fuel. [ABSTRACT FROM AUTHOR]

Ceramic sanitaryware products are produced using inorganic and non-metallic raw materials such as clay, kaolin, quartz and feldspar at certain rates. After mixing and grounding process, the slip is obtained. The products are shaped in gypsum or synthetic resin moulds. Green bodies are fired at 1250 °C for 16–18 h, and their water absorption values are less than 0.5%. Nowadays the most important issues are raw materials and energy costs. In this study, the sintering behaviour of Na-feldspar and K-feldspar, which are widely used in ceramic sanitaryware, is analysed by reducing to different grain sizes. The grain sizes of the samples containing Na-feldspar were reduced under 63 µm. It was found that the decrease in grain size of Na-feldspar contributed to the decrease in sintering temperature. Potassium feldspar was also added instead of Na-feldspar in order to develop deformation behaviour at higher temperature. The increase in the amount of K-feldspar contributed to the decrease in deformation values. However, the flexural strength of the bodies decreased. A decrease in grain size of Na-feldspar resulted in a reduction of 10 °C at the sintering temperature. The decrease in sintering temperature will provide a cost advantage of around 3%. It was also found that technical properties such as firing shrinkage, bulk density, and flexure strength increased as the grain size of Na-feldspar decreased. [ABSTRACT FROM AUTHOR]

The porous SiC-Mullite porous ceramics with different pore size were prepared by SiC particles, kaolin, Al(OH) 3 , and flake graphite, V 2 O 5 and AlF 3 were used as mineralizers, the pore size was controllable by adjusting the size of flake graphite. Then the improved empirical formula and grey theory were used to study the effect of the change in pore size on the material properties. The results showed that with the increase of mean pore size from 1.1 μm to 8.5 μm, the cold modulus of rupture and cold crushing strength decreased by 20.8 MPa and 13.7 MPa, respectively. And the thermal conductivity increased from 1.213 W⋅m−1⋅K−1 to 1.721 W⋅m−1⋅K−1 at 800 °C. The <5 μm pores were helped enhance the strength and decreased the thermal conductivity. [ABSTRACT FROM AUTHOR]

High-performance ceramics with low thermal conductivity, high mechanical properties, and idea thermal expansion coefficients have important applications in fields such as turbine blades and automotive engines. Currently, the thermal conductivity of ceramics has been significantly reduced by local doping/substitution or further high-entropy reconfiguration of the composition, but the mechanical properties, especially the fracture toughness, are insufficient and still need to be improved. In this work, based on the high-entropy titanate pyrochlore, TiO 2 was introduced for composite toughening and the high-entropy (Ho 0.2 Y 0.2 Dy 0.2 Gd 0.2 Eu 0.2) 2 Ti 2 O 7 -xTiO 2 (x = 0, 0.2, 0.4, 1.0 and 2.0) composites with high hardness (16.17 GPa), Young's modulus (289.3 GPa) and fracture toughness (3.612 MPa·m0.5), low thermal conductivity (1.22 W·m−1·K−1), and thermal expansion coefficients close to the substrate material (9.5 ×10−6/K) were successfully prepared by the solidification method. The fracture toughness of the composite toughened sample is 2.25 times higher than that before toughening, which exceeds most of the current low-thermal conductivity ceramics. • Preparation of high-entropy pyrochlore/TiO 2 composites by rapid melt solidification. • The composite toughened samples have ultrahigh fracture toughness (3.612 MPa·m0.5). • The solidified composites exhibit excellent mechanical and thermal properties. [ABSTRACT FROM AUTHOR]

Reaction-bonded SiC is a ceramic with excellent thermal properties, good corrosion resistance and the characteristic of near-net-shape manufacturing. However, the poor fracture toughness of free Si limits the applications of reaction-bonded SiC. In this study, TiC was added to reaction-bonded SiC and reacted with free Si to form Ti 3 SiC 2. The effects of TiC and carbon black on the mechanical properties of reaction-bonded SiC were investigated. The results demonstrated that the in-situ formation of Ti 3 SiC 2 and decrease in the content and size of free Si improved the mechanical properties of reaction-bonded SiC ceramics. The mechanical properties of TiC-added reaction-bonded SiC with 17.5 wt% carbon black were superior to those of TiC-added reaction-bonded SiC with 15 wt% carbon black. Moreover, increasing the TiC content of reaction-bonded SiC with 17.5 wt% carbon black from 0 to 7.5 wt% caused an increase in its bending strength from 183.92 to 424.43 MPa and an increase in fracture toughness from 3.7 to 5.24 MPa m1/2. [ABSTRACT FROM AUTHOR]

In Part 1 of this study, we investigated the macrokinetic parameters and phase formation mechanism in the combustion front of Zr–Nb–B mixtures. In the second part, we produced consolidated samples of solid solutions NbB 2 -(0.100%)ZrB 2 by hot pressing the combustion-derived powders at 1900 °C. By measuring the crystallographic parameters, mechanical and thermophysical properties of the produced bulk samples, we obtained valuable insights into the behavior of the solid solutions. Our results pave the way for the application-specific fine-tuning of the mechanical properties and thermal conductivity of diboride solid solutions in the Zr–Nb–B system for ultra-high temperature applications. Our findings have significant implications for the development of advanced materials with outstanding performance in extreme environments. [ABSTRACT FROM AUTHOR]

In this work, (20- x)MgO–20Al 2 O 3 –56SiO 2 –4B 2 O 3 - x CuO (x = 0, 0.25, 0.5, 0.75, 1, 1.25 mol%) glass-ceramics were synthesized by solid-state reaction method. The crystallization, microstructure, thermal and dielectric properties of (20- x)MgO–20Al 2 O 3 –56SiO 2 –4B 2 O 3 - x CuO glass-ceramics was discussed in detail. It was demonstrated that the CuO lowers the crystallization temperature of α-cordierite and promotes the crystallization process of MgO–Al 2 O 3 –SiO–B 2 O 3 glass-ceramics. Thus, the crystallization showed a substantial influence on the dielectric properties, as evidenced by an elevation in dielectric constant and a decrease in dielectric loss. Specifically, with the addition of 0.5 mol% CuO, the MgO–Al 2 O 3 –SiO–B 2 O 3 glass-ceramics sintered at 1050 °C shows excellent properties of: ε r = 5.04, tan δ = 2.2 × 10-4, κ = 3.4 W/mK and α = 1.75 × 10-6/°C. These works provide valuable insights into the design and development of (20- x)MgO–20Al 2 O 3 –56SiO 2 –4B 2 O 3 - x CuO glass-ceramics with tailored properties for structure/function integration in the electronics industry. [ABSTRACT FROM AUTHOR]