Search

Nanorod structures exhibit a high surface-to-volume ratio, enhancing the accessibility of electrolyte ions to the electrode surface and providing an abundance of active sites for improved electrochemical sensing performance. In this study, tetragonal α-MnO2 with a large K+-embedded tunnel structure, directly grown on microfibrous carbon paper to form densely packed nanorod arrays, is investigated as an electrocatalytic material for non-enzymatic glucose sensing. The MnO2 nanorods electrode demonstrates outstanding catalytic activity for glucose oxidation, showcasing a high sensitivity of 143.82 µA cm−2 mM−1 within the linear range from 0.01 to 15 mM, with a limit of detection (LOD) of 0.282 mM specifically for glucose molecules. Importantly, the MnO2 nanorods electrode exhibits excellent selectivity towards glucose over ascorbic acid and uric acid, which is crucial for accurate glucose detection in complex samples. For comparison, a gold electrode shows a lower sensitivity of 52.48 µA cm−2 mM−1 within a linear range from 1 to 10 mM. These findings underscore the superior performance of the MnO2 nanorods electrode in both sensitivity and selectivity, offering significant potential for advancing electrochemical sensors and bioanalytical techniques for glucose monitoring in physiological and clinical settings. [ABSTRACT FROM AUTHOR]

In the realm of electrochemical nitrite detection, the potent oxidizing nature of nitrite typically necessitates operation at high detection potentials. However, this study introduces a novel approach to address this challenge by developing a highly sensitive electrochemical sensor with a low reduction detection potential. Specifically, a copper metal nanosheet/carbon paper sensitive electrode (Cu/CP) was fabricated using a one-step electrodeposition method, leveraging the catalytic reduction properties of copper's high occupancy d-orbital. The Cu/CP sensor exhibited remarkable performance in nitrite detection, featuring a low detection potential of −0.05 V vs. Hg/HgO, a wide linear range of 10~1000 μM, an impressive detection limit of 0.079 μM (S/N = 3), and a high sensitivity of 2140 μA mM−1cm−2. These findings underscore the efficacy of electrochemical nitrite detection through catalytic reduction as a means to reduce the operational voltage of the sensor. By showcasing the successful implementation of this strategy, this work sets a valuable precedent for the advancement of electrochemical low-potential nitrite detection methodologies. [ABSTRACT FROM AUTHOR]

Skin-based wearable devices have gained significant attention due to advancements in soft materials and thin-film technologies. Nevertheless, traditional wearable electronics often entail expensive and intricate manufacturing processes and rely on metal-based substrates that are susceptible to corrosion and lack flexibility. In response to these challenges, this paper has emerged with an alternative substrate for wearable electrodes due to its cost-effectiveness and scalability in manufacturing. Paper-based electrodes offer an attractive solution with their inherent properties of high breathability, flexibility, biocompatibility, and tunability. In this study, we introduce carbon nanotube-based paper composites (CPC) electrodes designed for the continuous detection of biopotential signals, such as electrooculography (EOG), electrocardiogram (ECG), and electroencephalogram (EEG). To prevent direct skin contact with carbon nanotubes, we apply various packaging materials, including polydimethylsiloxane (PDMS), Eco-flex, polyimide (PI), and polyurethane (PU). We conduct a comparative analysis of their signal-to-noise ratios in comparison to conventional gel electrodes. Our system demonstrates real-time biopotential monitoring for continuous health tracking, utilizing CPC in conjunction with a portable data acquisition system. The collected data are analyzed to provide accurate heart rates, respiratory rates, and heart rate variability metrics. Additionally, we explore the feasibility using CPC for sleep monitoring by collecting EEG signals. [ABSTRACT FROM AUTHOR]

Herein, we developed a colorimetric method for the determination of Cu2+ and Zn2+ using NBD-G as a novel selective metal sensor. NBD-G was easily synthesized by a nucleophilic substitution reaction between 4-chloro-7-nitro-2,1,3-benzoxadiazole (NBD-Cl) and Girard's Reagent P. The NBD-G solution is yellow, but when it reacts with Cu2+ and Zn2+, its color changes selectively to red (510 nm) and orange (480 nm), respectively. NBD-G was used as a sensor for Cu2+ and Zn2+, showing a high sensitivity down to 0.77 µM for Cu2+ and 1.66 µM for Zn2+. NBD-G could determine both metals simultaneously; thus, it was applied to determine them in multimineral supplements, which showed excellent recoveries. Next, a filter paper impregnated with NBD-G was prepared as a test paper, and a simple, selective, and rapid onsite method for quantifying Cu2+ was developed as, interestingly, the paper showed no change upon the addition of Zn2+. Next, Cu2+ could be quantified with high selectivity and accuracy by photographing the color change with a smartphone camera and processing the image with Image J. The detection limit for Cu2+ using this method was 3.9 µM. Finally, the NBD-G test paper method was able to satisfactorily quantify Cu2+ spiked into the rainwater. [ABSTRACT FROM AUTHOR]

The increase in anthropogenic pollution raises serious concerns regarding contamination of water bodies and aquatic species with potential implications on human health. Pharmaceutical compounds are a type of contaminants of emerging concern that are increasingly consumed and, thus, being frequently found in the aquatic environment. In this sense, an electrochemical sensor based on an unmodified and untreated carbon fiber paper (CPS—carbon paper sensor) was simply employed for the analysis of trimethoprim antibiotic in fish samples. First, the analytical conditions were thoroughly optimized in order for the CPS to achieve maximum performance in trimethoprim determination. Therefore, an electrolyte (0.1 M Britton–Robinson buffer) pH of 7 was selected and for square wave voltammetry parameters, optimum values of amplitude, frequency and step potential corresponded to 0.02 V, 50 Hz, and 0.015 V, respectively, whereas the deposition of analyte occurred at +0.7 V for 60 s. In these optimum conditions, the obtained liner range (0.05 to 2 µM), sensitivity (48.8 µA µM−1 cm−2), and LOD (0.065 µM) competes favorably with the commonly used GCE-based sensors or BDD electrodes that employ nanostructuration or are more expensive. The CPS was then applied for trimethoprim determination in fish samples after employing a solid phase extraction procedure based on QuEChERS salts, resulting in recoveries of 105.9 ± 1.8% by the standard addition method. [ABSTRACT FROM AUTHOR]

Vibration sensors are widely used in many fields like industry, agriculture, military, medicine, environment, etc. However, due to the speedy upgrading, most sensors composed of rigid or even toxic materials cause pollution to the environment and give rise to an increased amount of electronic waste. To meet the requirement of green electronics, biodegradable materials are advocated to be used to develop vibration sensors. Herein, a vibration sensor is reported based on a strategy of pencil-drawing graphite on paper. Specifically, a repeated pencil-drawing process is carried out on paper with a zigzag-shaped framework and parallel microgrooves, to form a graphite coating, thus serving as a functional conductive layer for electromechanical signal conversion. To enhance the sensor's sensitivity to vibration, a mass is loaded in the center of the paper, so that higher oscillation amplitude could happen under vibrational excitation. In so doing, the paper-based sensor can respond to vibrations with a wide frequency range from 5 Hz to 1 kHz, and vibrations with a maximum acceleration of 10 g. The results demonstrate that the sensor can not only be utilized for monitoring vibrations generated by the knuckle-knocking of plastic plates or objects falling down but also can be used to detect vibration in areas such as the shield cut head to assess the working conditions of machinery. The paper-based MEMS vibration sensor exhibits merits like easy fabrication, low cost, and being environmentally friendly, which indicates its great application potential in vibration monitoring fields. [ABSTRACT FROM AUTHOR]

As power sources for Internet-of-Things sensors, thermoelectric generators must exhibit compactness, flexibility, and low manufacturing costs. Stretchable and flexible painted thermoelectric generators were fabricated on Japanese paper using inks with dispersed p- and n-type single-walled carbon nanotubes (SWCNTs). The p- and n-type SWCNT inks were dispersed using the anionic surfactant of sodium dodecylbenzene sulfonate and the cationic surfactant of dimethyldioctadecylammonium chloride, respectively. The bundle diameters of the p- and n-type SWCNT layers painted on Japanese paper differed significantly; however, the crystallinities of both types of layers were almost the same. The thermoelectric properties of both types of layers exhibited mostly the same values at 30 °C; however, the properties, particularly the electrical conductivity, of the n-type layer increased linearly, and of the p-type layer decreased as the temperature increased. The p- and n-type SWCNT inks were used to paint striped patterns on Japanese paper. By folding at the boundaries of the patterns, painted generators can shrink and expand, even on curved surfaces. The painted generator (length: 145 mm, height: 13 mm) exhibited an output voltage of 10.4 mV and a maximum power of 0.21 μW with a temperature difference of 64 K at 120 °C on the hot side. [ABSTRACT FROM AUTHOR]

The use of enzyme-based biosensors for the detection and quantification of analytes of interest such as contaminants of emerging concern, including over-the-counter medication, provides an attractive alternative compared to more established techniques. However, their direct application to real environmental matrices is still under investigation due to the various drawbacks in their implementation. Here, we report the development of bioelectrodes using laccase enzymes immobilized onto carbon paper electrodes modified with nanostructured molybdenum disulfide (MoS2). The laccase enzymes were two isoforms (LacI and LacII) produced and purified from the fungus Pycnoporus sanguineus CS43 that is native to Mexico. A commercial purified enzyme from the fungus Trametes versicolor (TvL) was also evaluated to compare their performance. The developed bioelectrodes were used in the biosensing of acetaminophen, a drug widely used to relieve fever and pain, and of which there is recent concern about its effect on the environment after its final disposal. The use of MoS2 as a transducer modifier was evaluated, and it was found that the best detection was achieved using a concentration of 1 mg/mL. Moreover, it was found that the laccase with the best biosensing efficiency was LacII, which achieved an LOD of 0.2 µM and a sensitivity of 0.108 µA/µM cm2 in the buffer matrix. Moreover, the performance of the bioelectrodes in a composite groundwater sample from Northeast Mexico was analyzed, achieving an LOD of 0.5 µM and a sensitivity of 0.015 µA/µM cm2. The LOD values found are among the lowest reported for biosensors based on the use of oxidoreductase enzymes, while the sensitivity is the highest currently reported. [ABSTRACT FROM AUTHOR]

This study presents a portable, low-cost, point-of-care (POC) system for the simultaneous detection of blood glucose and hematocrit. The system consists of a disposable origami microfluidic paper-based analytical device (μPAD) for plasma separation, filtration, and reaction functions and a 3D-printed cassette for hematocrit and blood glucose detection using a smartphone. The origami μPAD is patterned using a cost-effective label printing technique instead of the conventional wax printing method. The 3D-printed cassette incorporates an array of LED lights, which mitigates the effects of intensity variations in the ambient light and hence improves the accuracy of the blood glucose and hematocrit concentration measurements. The hematocrit concentration is determined quantitatively by measuring the distance of plasma wicking along the upper layer of the origami μPAD, which is pretreated with sodium chloride and Tween 20 to induce dehydration and aggregation of the red blood cells. The filtered plasma also penetrates to the lower layer of the origami μPAD, where it reacts with embedded colorimetric assay reagents to produce a yellowish-brown complex. A color image of the reaction complex is captured using a smartphone inserted into the 3D-printed cassette. The image is analyzed using self-written RGB software to quantify the blood glucose concentration. The calibration results indicate that the proposed detection platform provides an accurate assessment of the blood glucose level over the range of 45–630 mg/dL (R2 = 0.9958). The practical feasibility of the proposed platform is demonstrated by measuring the blood glucose and hematocrit concentrations in 13 human whole blood samples. Taking the measurements obtained from commercial glucose and hematocrit meters as a benchmark, the proposed system has a differential of no more than 6.4% for blood glucose detection and 9.1% for hematocrit detection. Overall, the results confirm that the proposed μPAD is a promising solution for cost-effective and reliable POC health monitoring. [ABSTRACT FROM AUTHOR]

Specialized cancer treatments have the potential to exploit glutamine dependence to increase patient survival rates. Glutamine diagnostics capable of tracking a patient's response to treatment would enable a personalized treatment dosage to optimize the tradeoff between treatment success and dangerous side effects. Current clinical glutamine testing requires sophisticated and expensive lab-based tests, which are not broadly available on a frequent, individualized basis. To address the need for a low-cost, portable glutamine diagnostic, this work engineers a cell-free glutamine biosensor to overcome assay background and signal-to-noise limitations evident in previously reported studies. The findings from this work culminate in the development of a shelf-stable, paper-based, colorimetric glutamine test with a high signal strength and a high signal-to-background ratio for dramatically improved signal resolution. While the engineered glutamine test is important progress towards improving the management of cancer and other health conditions, this work also expands the assay development field of the promising cell-free biosensing platform, which can facilitate the low-cost detection of a broad variety of target molecules with high clinical value. [ABSTRACT FROM AUTHOR]

A simple, equipment-free, direct fluorometric method, employing paper-based analytical devices (PADs) as sensors, for the selective determination of quinine (QN) is described herein. The suggested analytical method exploits the fluorescence emission of QN without any chemical reaction after the appropriate pH adjustment with nitric acid, at room temperature, on the surface of a paper device with the application of a UV lamp at 365 nm. The devices crafted had a low cost and were manufactured with chromatographic paper and wax barriers, and the analytical protocol followed was extremely easy for the analyst and required no laboratory instrumentation. According to the methodology, the user must place the sample on the detection area of the paper and read with a smartphone the fluorescence emitted by the QN molecules. Many chemical parameters were optimized, and a study of interfering ions present in soft drink samples was carried out. Additionally, the chemical stability of these paper devices was considered in various maintenance conditions with good results. The detection limit calculated as 3.3 S/N was 3.6 mg L−1, and the precision of the method was satisfactory, being from 3.1% (intra-day) to 8.8% (inter-day). Soft drink samples were successfully analyzed and compared with a fluorescence method. [ABSTRACT FROM AUTHOR]

A pipette-free and fully integrated device that can be used to accurately recognize the presence of infectious pathogens is an important and useful tool in point-of-care testing, particularly when aiming to decrease the unpredictable threats posed by disease outbreak. In this study, a paper device is developed to integrate the three main processes required for detecting infectious pathogens, including DNA extraction, loop-mediated isothermal amplification (LAMP), and detection. All key reagents, including sodium dodecyl sulfate (SDS), NaOH, LAMP reagents, and carmoisine, are placed on the paper device. The paper device is operated simply via sliding and folding without using any bulky equipment, and the results can be directly observed by the naked eye. The optimized concentrations of sodium dodecyl sulfate (SDS), sodium hydroxide (NaOH), and carmoisine were found to be 0.1%, 0.1 M, and 0.5 mg/mL, respectively. The paper device was used to detect Enterococcus faecium at concentrations as low as 102 CFU/mL within 60 min. Also, E. faecium spiked in milk was successfully detected using the paper device, demonstrating the feasible application in real sample analysis. [ABSTRACT FROM AUTHOR]

Aptamers are short oligonucleotides designed to possess high binding affinity towards specific target compounds (ions, molecules, or cells). Due to their function and unique advantages, aptamers are considered viable alternatives to antibodies as biorecognition elements in bioassays and biosensors. On the other hand, paper-based devices (PADs) have emerged as a promising and powerful technology for the fabrication of low-cost analytical tools, mainly intended for on-site and point-of-care applications. The present work aims to provide a comprehensive overview of paper-based aptasensors. The review describes the fabrication methods and working principles of paper-based devices, the properties of aptamers as bioreceptors, the different modes of detection used in conjunction with aptasensing PADs, and representative applications for the detection of ions, small molecules, proteins, and cells. The future challenges and prospects of these devices are also discussed. [ABSTRACT FROM AUTHOR]

Image compression is a vital component for domains in which the computational resources are usually scarce such as automotive or telemedicine fields. Also, when discussing real-time systems, the large amount of data that must flow through the system can represent a bottleneck. Therefore, the storage of images, alongside the compression, transmission, and decompression procedures, becomes vital. In recent years, many compression techniques that only preserve the quality of the region of interest of an image have been developed, the other parts being either discarded or compressed with major quality loss. This paper proposes a study of relevant papers from the last decade which are focused on the selection of a region of interest of an image and on the compression techniques that can be applied to that area. To better highlight the novelty of the hybrid methods, classical state-of-the-art approaches are also analyzed. The current work will provide an overview of classical and hybrid compression methods alongside a categorization based on compression ratio and other quality factors such as mean-square error and peak signal-to-noise ratio, structural similarity index measure, and so on. This overview can help researchers to develop a better idea of what compression algorithms are used in certain domains and to find out if the presented performance parameters are of interest for the intended purpose. [ABSTRACT FROM AUTHOR]

This document is a summary of a special issue of the journal Sensors, titled "Emerging AI+X-Based Sensor and Networking Technologies including Selected Papers from ICGHIT 2022–2023." The special issue features selected papers from the 10th and 11th International Conferences on Green and Human Information Technology (ICGHITs), which were held in Korea and Thailand. The conferences focused on the theme of "Emerging Artificial Intelligent (AI)+X technology" and "Hyper Automation + Human AI" respectively. The selected papers cover various topics such as network security, routing protocols, signal detection, and clustering mechanisms, all incorporating AI-based methods. The issue also includes papers on topics like secure authentication, distance estimation in RFID systems, energy optimization in smart homes, blockchain technology, and radar signal detection. The authors emphasize the importance of both technology and humanity in advancing green and information technologies. [Extracted from the article]

This paper presents the development of cheap and selective Paper-based Analytical Devices (PADs) for selective Pd(II) determination from very acidic aqueous solutions. The PADs were obtained by impregnating two cm-side squares of filter paper with an azoic ligand, (2-(tetrazolylazo)-1,8 dihydroxy naphthalene-3,6,-disulphonic acid), termed TazoC. The so-obtained orange TazoC-PADs interact quickly with Pd(II) in aqueous solutions by forming a complex purple-blue-colored already at pH lower than 2. The dye complexes no other metal ions at such an acidic media, making TazoC-PADs highly selective to Pd(II) detection. Besides, at higher pH values, other cations, for example, Cu(II) and Ni(II), can interact with TazoC through the formation of stable and pink-magenta-colored complexes; however, it is possible to quantify Pd(II) in the presence of other cations using a multivariate approach. To this end, UV-vis spectra of the TazoC-PADs after equilibration with the metal ions solutions were registered in the 300–800 nm wavelength range. By applying Partial Least Square regression (PLS), the whole UV-vis spectra of the TazoC-PADs were related to the Pd(II) concentrations both when present alone in solution and also in the presence of Cu(II) and Ni(II). Tailored PLS models obtained with matrix-matched standard solutions correctly predicted Pd(II) concentrations in unknown samples and tap water spiked with the metal cation, making the method promising for quick and economical sensing of Pd(II). [ABSTRACT FROM AUTHOR]

Iodine is an essential micronutrient for humans due to its fundamental role in the biosynthesis of thyroid hormones. As a key parameter to assess health conditions, iodine intake needs to be monitored to ascertain and prevent iodine deficiency. Iodine is available from various food sources (such as seaweed, fish, and seafood, among others) and dietary supplements (multivitamins or mineral supplements). In this work, a microfluidic paper-based analytical device (μPAD) to quantify iodide in seaweed and dietary supplements is described. The developed μPAD is a small microfluidic device that emerges as quite relevant in terms of its analytical capacity. The quantification of iodide is based on the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) by hydrogen peroxide in the presence of iodine, which acts as the catalyst to produce the blue form of TMB. Additionally, powder silica was used to intensify and uniformize the colour of the obtained product. Following optimization, the developed μPAD enabled iodide quantification within the range of 10–100 µM, with a detection limit of 3 µM, and was successfully applied to seaweeds and dietary supplements. The device represents a valuable tool for point-of-care analysis, can be used by untrained personnel at home, and is easily disposable, low-cost, and user-friendly. [ABSTRACT FROM AUTHOR]

Paper-based biosensors are a potential paradigm of sensitivity achieved via microporous spreading/microfluidics, simplicity, and affordability. In this paper, we develop decorated paper with graphene and conductive polymer (herein referred to as graphene conductive polymer paper-based sensor or GCPPS) for sensitive detection of biomolecules. Planetary mixing resulted in uniformly dispersed graphene and conductive polymer ink, which was applied to laser-cut Whatman filter paper substrates. Scanning electron microscopy and Raman spectroscopy showed strong attachment of conductive polymer-functionalized graphene to cellulose fibers. The GCPPS detected dopamine and cytokines, such as tumor necrosis factor-alpha (TNF-α), and interleukin 6 (IL-6) in the ranges of 12.5–400 µM, 0.005–50 ng/mL, and 2 pg/mL–2 µg/mL, respectively, using a minute sample volume of 2 µL. The electrodes showed lower detection limits (LODs) of 3.4 µM, 5.97 pg/mL, and 9.55 pg/mL for dopamine, TNF-α, and IL-6 respectively, which are promising for rapid and easy analysis for biomarkers detection. Additionally, these paper-based biosensors were highly selective (no serpin A1 detection with IL-6 antibody) and were able to detect IL-6 antigen in human serum with high sensitivity and hence, the portable, adaptable, point-of-care, quick, minute sample requirement offered by our fabricated biosensor is advantageous to healthcare applications. [ABSTRACT FROM AUTHOR]

Traces of mercury ions in environmental water can harm humans and animals. Paper-based visual detection methods have been widely developed for the rapid detection of mercury ions; however, existing methods are not sensitive enough to be used in real environments. Here, we developed a novel, simple and effective visual fluorescent sensing paper-based chip for the ultrasensitive detection of mercury ions in environmental water. CdTe-quantum-dots-modified silica nanospheres were firmly absorbed by and anchored to the fiber interspaces on the paper's surface to effectively avoid the unevenness caused by liquid evaporation. The fluorescence of quantum dots emitted at 525 nm can be selectively and efficiently quenched with mercury ions, and the ultrasensitive visual fluorescence sensing results attained using this principle can be captured using a smartphone camera. This method has a detection limit of 2.83 µg/L and a fast response time (90 s). We successfully achieved the trace spiking detection of seawater (from three regions), lake water, river water and tap water with recoveries in the range of 96.8–105.4% using this method. This method is effective, low-cost, user-friendly and has good prospects for commercial application. Additionally, the work is expected to be utilized in the automated big data collection of large numbers of environmental samples. [ABSTRACT FROM AUTHOR]

In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. The antenna size of 40 mm × 40 mm × 0.44 mm with a partial ground, covers wireless and mobile bands ranging from 1.91 GHz to 6.75 GHz. The parametric analysis is performed to achieve optimized design parameters of the antenna. The U-shaped and C-shaped emitters are meant to function at 2.4 GHz and 5.9 GHz, respectively, while the primary emitter is designed to operate at 3.5 GHz. The proposed antenna achieved peak gain and radiation efficiency of 3.4 dBi and 90%, respectively. Simulated and measured results of the reflection coefficient, radiation pattern, gain, and efficiency show that the antenna design is in favorable agreement. Since the proposed antenna achieved wideband (1.91–6.75 GHz) using PIN diode configuration, using this technique the need for numerous electronic components to provide multiband frequency is avoided. [ABSTRACT FROM AUTHOR]

Home-based rehabilitation programs for older adults have demonstrated effectiveness, desirability, and reduced burden. However, the feasibility and effectiveness of balance-intervention training delivered through traditional paper-versus novel smartphone-based methods is unknown. Therefore, the purpose of this study was to evaluate if a home-based balance-intervention program could equally improve balance performance when delivered via smartphone or paper among adults over the age of 65. A total of 31 older adults were randomized into either a paper or phone group and completed a 4-week asynchronous self-guided balance intervention across 12 sessions for approximately 30 min per session. Baseline, 4-week, and 8-week walking and standing balance evaluations were performed, with exercise duration and adherence recorded. Additional self-reported measures were collected regarding the enjoyment, usability, difficulty, and length of the exercise program. Twenty-nine participants completed the balance program and three assessments, with no group differences found for any outcome measure. Older adults demonstrated an approximately 0.06 m/s faster gait velocity and modified balance strategies during walking and standing conditions following the intervention protocol. Participants further self-reported similar enjoyment, difficulty, and exercise effectiveness. Results of this study demonstrated the potential to safely deliver home-based interventions as well as the feasibility and effectiveness of delivering balance intervention through a smartphone-based application. [ABSTRACT FROM AUTHOR]

Multiband (MB) optical transmission targets increasing the capacity of operators' optical transport networks. However, nonlinear impairments (NLI) affect each optical channel in the C+L+S bands differently, and, therefore, the routing and spectrum assignment (RSA) problem needs to be complemented with fast and accurate tools to consider the quality of transmission (QoT) within the provisioning process. This paper proposes a digital twin-assisted approach for lightpath provisioning to provide a complete solution for the RSA problem that ensures the required QoT in MB optical networks. The OCATA time domain digital twin is proposed, not only to estimate the QoT of a selected path but also to support the QoT-based channel assignment process. OCATA is based on a Deep Neural Network (DNN) to model the propagation of the optical signal. However, because of the different impacts of nonlinear noise on each channel and the large number of channels that need to be considered in C+L+S MB scenarios, OCATA needs to be adapted to make it scalable, while keeping its high accuracy and fast QoT estimation characteristics. In consequence, a complete methodology is proposed in this work that limits the number of channels being modeled to just a few. Moreover, OCATA-MB helps to mitigate NLI noise by programming the receiver at the provisioning time and thus with very little complexity compared to its equivalent implemented during the operation. NLI noise mitigation can be applied in the case when a lightpath cannot be provisioned because none of the available channels can provide the required QoT, making it an advantageous tool for reducing connection blocking. Exhaustive simulation results demonstrate the remarkable accuracy of OCATA-MB in estimating the QoT for any channel. Interestingly, by utilizing the proposed OCATA-MB-assisted lightpath provisioning approach, a reduction of the blocking ratio exceeding 50% when compared to traditional approaches is shown when NLI noise mitigation is not applied. If NLI mitigation is implemented, an additional over 50% blocking reduction is achieved. [ABSTRACT FROM AUTHOR]

Hydrogen sulfide (H2S) is known to participate in bacteria-induced inflammatory response in periodontal diseases. Therefore, it is necessary to quantify H2S produced by oral bacteria for diagnosis and treatment of oral diseases including halitosis and periodontal disease. In this study, we introduce a paper-based colorimetric assay for detecting bacterial H2S utilizing silver/Nafion/polyvinylpyrrolidone membrane and a 96-well microplate. This H2S-sensing paper showed a good sensitivity (8.27 blue channel intensity/μM H2S, R2 = 0.9996), which was higher than that of lead acetate paper (6.05 blue channel intensity/μM H2S, R2 = 0.9959). We analyzed the difference in H2S concentration released from four kinds of oral bacteria (Eikenella corrodens, Streptococcus sobrinus, Streptococcus mutans, and Lactobacillus casei). Finally, the H2S level in Eikenella corrodens while varying the concentration of cysteine and treatment time was quantified. This paper-based colorimetric assay can be utilized as a simple and effective tool for in vitro screening of H2S-producing ability of many bacteria as well as salivary H2S analysis. [ABSTRACT FROM AUTHOR]

The paper describes the development of an electrochemical sensor to be used for the determination of synthetic food colorants such as Sunset Yellow FCF (SY) and Tartrazine (TZ). The sensor is a carbon paper (CP) electrode, manufactured by using hot lamination technology and volume modified with fine-grained graphite powder (GrP). The sensor (GrP/CP) was characterized by scanning electron microscopy, energy dispersive spectrometry, electrochemical impedance analysis, cyclic, linear sweep and differential pulse voltammetry. The mechanism of SY and TZ electrochemical oxidation on GrP/CP was studied. The developed sensor has good electron transfer characteristics and low electron resistance, high sensitivity and selectivity. Applying the differential pulse mode, linear dynamic ranges of 0.005–1.0 μM and 0.02–7.5 μM with limits of detection of 0.78 nM and 8.2 nM for SY and TZ, respectively, were obtained. The sensor was used to detect SY and TZ in non-alcoholic and alcoholic drinks. The results obtained from drink analysis prove good reproducibility (RSD ≤ 0.072) and accuracy (recovery 96–104%). [ABSTRACT FROM AUTHOR]

In this paper, the paper cups were used as the research objects, and the machine vision detection technology was combined with different image processing techniques to investigate a non-contact optical automatic detection system to identify the defects of the manufactured paper cups. The combined ring light was used as the light source, an infrared (IR) LED matrix panel was used to provide the IR light to constantly highlight the outer edges of the detected objects, and a multi-grid pixel array was used as the image sensor. The image processing techniques, including the Gaussian filter, Sobel operator, Binarization process, and connected component, were used to enhance the inspection and recognition of the defects existing in the produced paper cups. There were three different detection processes for paper cups, which were divided into internal, external, and bottom image acquisition processes. The present study demonstrated that all the detection processes could clearly detect the surface defect features of the manufactured paper cups, such as dirt, burrs, holes, and uneven thickness. Our study also revealed that the average time for the investigated Automatic Optical Detection to detect the defects on the paper cups was only 0.3 s. [ABSTRACT FROM AUTHOR]

The distinct properties and affordances of paper provide benefits that enabled paper to maintain an important role in the digital age. This is so much so, that some pen–paper interaction has been imitated in the digital world with touchscreens and stylus pens. Because digital medium also provides several advantages not available to physical paper, there is a clear benefit to merge the two mediums. Despite the plethora of concepts, prototypes and systems to digitise handwritten information on paper, these systems require specially prepared paper, complex setups and software, which can be used solely in combination with paper, and, most importantly, do not support the concurrent precise interaction with both mediums (paper and touchscreen) using one pen only. In this paper, we present the design, fabrication and evaluation of the Hybrid Stylus. The Hybrid Stylus is assembled with the infinity pencil tip (nib) made of graphite and a specially designed shielded tip holder that is attached to an active stylus. The stylus can be used for writing on a physical paper, while it still maintains all the features needed for tablet interaction. Moreover, the stylus also allows simultaneous digitisation of handwritten information on the paper when the paper is placed on the tablet screen. In order to evaluate the concept, we also add a user-friendly manual alignment of paper position on the underlying tablet computer The evaluation demonstrates that the system achieves almost perfect digitisation of strokes (98.6% of strokes were correctly registered with only 1.2% of ghost strokes) whilst maintaining excellent user experience of writing with a pencil on the paper. [ABSTRACT FROM AUTHOR]

We present the development of an electrochemical paper-based analytical device (ePAD) for the detection of methamphetamine. Methamphetamine is a stimulant that young people use as an addictive narcotic, and it must be detected quickly since it may be hazardous. The suggested ePAD has the advantages of being simple, affordable, and recyclable. This ePAD was developed by immobilizing a methamphetamine-binding aptamer onto Ag-ZnO nanocomposite electrodes. The Ag-ZnO nanocomposites were synthesized via a chemical method and were further characterized via scanning electron microscopy, Fourier transform infrared spectroscopy, and UV-vis spectrometry in terms of their size, shape, and colloidal activity. The developed sensor showed a limit of detection of about 0.1 μg/mL, with an optimum response time of about 25 s, and its extensive linear range was between 0.01 and 6 μg/mL. The application of the sensor was recognized by spiking different beverages with methamphetamine. The developed sensor has a shelf life of about 30 days. This cost-effective and portable platform might prove to be highly successful in forensic diagnostic applications and will benefit those who cannot afford expensive medical tests. [ABSTRACT FROM AUTHOR]

To stabilize the detection signal of palladium-based hydrogen sensors on paper substrates, a graphite intermediate layer was painted on the surface of paper. The graphite-on-paper (GOP) substrate offers advantages such as good thermo-electrical conductivity, low cost, and uncomplicated preparation technology. Quasi-1-dimensional palladium (Pd) thin films with 8 nm and 60 nm thicknesses were deposited on the GOP substrates using the vacuum evaporation technique. Thanks to the unique properties of the GOP substrate, a continuous Pd microfiber network structure appeared after deposition of the ultra-thin Pd film. Additionally, the sensing performance of the palladium-based hydrogen sensor was not affected, whether using GOP or paper substrate at 25 °C. Surprisingly, heating-induced loss of sensitivity was restrained due to the increased electrical conductivity of the GOP substrate at 50 °C. [ABSTRACT FROM AUTHOR]

A novel, rapid, and facile method for the colorimetric determination of calcium using micro-analytical paper-based devices (μ-PADs) was developed. The proposed analytical method utilizes the color differences developing, after the addition of calcium, on the surface of the devices because of the complexation reaction of calcium with Methylthymol Blue (MTB) at room temperature, in alkaline pH. The devices were manufactured with chromatographic paper, using wax barriers, and the analytical protocol was easily implemented without the need of any experimental apparatus except for a simple imaging device. The user must regulate the pH, add the solutions on the paper, and measure the color intensity of the formed Ca(II)–MTB complex with a flatbed scanner. The experimental conditions for optimum color development, the possible interfering substances, and the reliability of the paper devices in different preserving conditions were optimized, with satisfactory results. The method exhibited acceptable detection limits (2.9 mg L−1) with sufficiently good precision, which varied from 4.2% (intra-day) to 6.4% (inter-day). Saliva samples from healthy volunteers were successfully analyzed, and the calcium levels were calculated in the range of 30.71 to 84.15 mg L−1. [ABSTRACT FROM AUTHOR]

The direct integration of paper-based microfluidic fuel cells (μFC's) toward creating autonomous lateral flow assays has attracted attention. Here, we show that an air-breathing paper-based μFC could be used as a power supply in pregnancy tests by oxidizing the human urine used for the diagnosis. We present an air-breathing paper-based μFC connected to a pregnancy test, and for the first time, as far as we know, it is powered by human urine without needing any external electrolyte. It uses TiO 2 -Ni as anode and Pt/C as cathode; the performance shows a maximum value of voltage and current and power densities of ∼0.96 V, 1.00 mA cm − 2 , and 0.23 mW cm − 2 , respectively. Furthermore, we present a simple design of a paper-based μFC's stack powered with urine that shows a maximum voltage and maximum current and power densities of ∼1.89 V, 2.77 mA cm − 2 and 1.38 mW cm − 2 , respectively, which powers the display of a pregnancy test allowing to see the analysis results. [ABSTRACT FROM AUTHOR]

Adolescent idiopathic scoliosis (AIS) is a common disease that, in many cases, can be conservatively treated through bracing. High adherence to brace prescription is fundamental to gaining the maximum benefit from this treatment approach. Wearable sensors are available that objectively monitor the brace-wearing time, but their use, combined with other interventions, is poorly investigated. The aims of the current review are as follows: (i) to summarize the real compliance with bracing reported by studies using sensors; (ii) to find out the real brace wearing rate through objective electronic monitoring; (iii) to verify if interventions made to increase adherence to bracing can be effective according to the published literature. We conducted a systematic review of the literature published on Medline, EMBASE, CINAHL, Scopus, CENTRAL, and Web of Science. We identified 466 articles and included examples articles, which had a low to good methodological quality. We found that compliance a greatly varied between 21.8 and 93.9% (weighted average: 58.8%), real brace wearing time varied between 5.7 and 21 h per day (weighted average 13.3), and specific interventions seemed to improve both outcomes, with compliance increasing from 58.5 to 66% and brace wearing increasing from 11.9 to 15.1 h per day. Two comparative studies showed positive effects of stand-alone counseling and information on the sensors' presence when added to counseling. Sensors proved to be useful tools for objectively and continuously monitoring adherence to therapy in everyday clinical practice. Specific interventions, like the use of sensors, counseling, education, and exercises, could increase compliance. However, further studies using high-quality designs should be conducted in this field. [ABSTRACT FROM AUTHOR]

In conclusion, the papers collected in this Special Issue summarize significant advances in the field of optical sensors, with specific contributions in sensor technology and applications of fiber Bragg gratings, resonators and spectroscopy. The performance of this integrated sensor is demonstrated using glucose solutions (0.05-0.3 g/mL) and the sensor response is shown to be dynamic and reversible. The refractive index sensor exhibits a linear response in the refractive index range of 1.333-1.358 RIU (refractive index unit), with a sensitivity of 32.4 RIU SP -1 sp and a resolution of 2 × 10 SP -3 sp RIU at the refractive index of water. Today, optical sensors are the subject of a very significant number of studies and applications. [Extracted from the article]

Since the determination of the high toxicity of bisphenol A, alternative structures for bisphenols have been synthesized, resulting in bisphenols C, E, F, S, and Z. These bisphenols have replaced bisphenol A in plastic bottles, toys, and cans used for preserving food. Later, the toxicity and negative effects of all of these bisphenols on people's health were proven. Therefore, there is a need for a fast ultrasensitive screening method that is able to detect the presence of these bisphenols in any condition directly from food samples. This paper presented a disposable device based on the utilization of a 2D disposable paper stochastic sensor for the fast ultrasensitive screening of food samples for bisphenols A, C, E, F, S, and Z. The 2D disposable sensor was obtained by the deposition of graphene and silver nanolayers on paper using cold plasma. Furthermore, the active side of the sensor was modified using 2,3,7,8,12,13,17,18-octaethyl-21H,23H Mn porphyrin. The limits of quantification of these bisphenols were 1 fmol L−1 for bisphenols C and E, 10 fmol L−1 for bisphenols A and F, 10 pmol L−1 for bisphenol S, and 1 pmol L−1 for bisphenol Z. The recoveries of these bisphenols in milk, canned fruits, vegetables, and fish were higher than 99.00% with RSD (%) values lower than 1.50%. [ABSTRACT FROM AUTHOR]

Soil tests for plant-available phosphorus (P) are suggested to provide offsite P analysis required to monitor P fertilizer application and reduce P losses to downstream water. However, procedural and cost limitations of current soil phosphate tests have restricted their widespread use and have made them accessible only in laboratories. This study proposes a novel paper-based reagentless electrochemical soil phosphate sensor to extract and detect soil phosphate using an inexpensive and simple approach. In this test, concentrated Mehlich-3 and molybdate ions were impregnated in filter paper, which served as the phosphate extraction and reaction zone, and was followed by electrochemical detection using cyclic voltammetry signals. Soil samples from 22 sampling sites were used to validate this method against inductively coupled plasma optical emission spectroscopy (ICP) soil phosphate tests. Regression and correlation analyses showed a significant relationship between phosphate determinations by ICP and the proposed method, delivering a correlation coefficient, r, of 0.98 and a correlation slope of 1.02. The proposed approach provided a fast, portable, low-cost, accessible, reliable, and single-step test to extract and detect phosphate simultaneously with minimum waste (0.5 mL per sample), which made phosphate characterization possible in the field. [ABSTRACT FROM AUTHOR]

The role of humidity sensors in different industries and field applications, such as agriculture, food monitoring, biomedical equipment, heating, and ventilation, is well known. However, most commercially available humidity sensors are based on polymers or electronic materials that are not degradable and thus contribute to electronic waste. Here, we report a low-cost, flexible, easy-to-fabricate, and eco-friendly parallel-plate capacitive humidity sensor for field applications. The sensor is fabricated from copper tape and tissue paper, where copper tape is used to create the plates of the capacitor, and tissue paper is used as a dielectric sensing layer. Along with the low cost, the high sensitivity, better response and recovery times, stability, and repeatability make this sensor unique. The sensor was tested for relative humidity (RH), ranging from 40% to 99%, and the capacitance varied linearly with RH from 240 pF to 720 pF, as measured by an Arduino. The response time of the sensor is ~1.5 s, and the recovery time is ~2.2 s. The experiment was performed 4–5 times on the same sensor, and repeatable results were achieved with an accuracy of ±0.1%. Furthermore, the sensor exhibits a stable response when tested at different temperatures. Due to the above advantages, the presented sensor can find ready applications in different areas. [ABSTRACT FROM AUTHOR]

The electrocardiogram (ECG) signal describes the heart's electrical activity, allowing it to detect several health conditions, including cardiac system abnormalities and dysfunctions. Nowadays, most patient medical records are still paper-based, especially those made in past decades. The importance of collecting digitized ECGs is twofold: firstly, all medical applications can be easily implemented with an engineering approach if the ECGs are treated as signals; secondly, paper ECGs can deteriorate over time, therefore a correct evaluation of the patient's clinical evolution is not always guaranteed. The goal of this paper is the realization of an automatic conversion algorithm from paper-based ECGs (images) to digital ECG signals. The algorithm involves a digitization process tested on an image set of 16 subjects, also with pathologies. The quantitative analysis of the digitization method is carried out by evaluating the repeatability and reproducibility of the algorithm. The digitization accuracy is evaluated both on the entire signal and on six ECG time parameters (R-R peak distance, QRS complex duration, QT interval, PQ interval, P-wave duration, and heart rate). Results demonstrate the algorithm efficiency has an average Pearson correlation coefficient of 0.94 and measurement errors of the ECG time parameters are always less than 1 mm. Due to the promising experimental results, the algorithm could be embedded into a graphical interface, becoming a measurement and collection tool for cardiologists. [ABSTRACT FROM AUTHOR]

With a growing number of electronic devices surrounding our daily life, it becomes increasingly important to create solutions for clear and simple communication and interaction at the human machine interface (HMI). Haptic feedback solutions play an important role as they give a clear direct link and response to the user. This work demonstrates multifunctional haptic feedback devices based on fully printed piezoelectric transducers realized with functional polymers on thin paper substrate. The devices are flexible; lightweight and show very high out-of-plane deflection of 213 µm at a moderate driving voltage of 50 Vrms (root mean square) achieved by an innovative multilayer design with up to five individually controllable active layers. The device creates a very clear haptic sensation to the human skin with a blocking force of 0.6 N at the resonance frequency of 320 Hz, which is located in the most sensitive range of the human fingertip. Additionally the transducer generates audible information above two kilohertz with a remarkable high sound pressure level. Thus the paper-based approach can be used for interactive displays in combination with touch sensation; sound and color prints. The work gives insights into the manufacturing process; the electrical characteristics; and an in-depth analysis of the 3D deflection of the device under variable conditions [ABSTRACT FROM AUTHOR]

Microneedle (MN) is a novel technique of the biomedical engineering field because of its ability to evaluate bioinformation via minimal invasion. One of the urgent requirements for ground-breaking health care monitoring is persistent monitoring. Hollow microneedles are extremely attractive to extract skin interstitial fluid (ISF) for analysis, which makes them perfect for sensing biomarkers and facilitating diagnosis. Nevertheless, its intricate fabrication process has hampered its extensive application. The present research demonstrates an easy one-step preparation approach for hollow MNs on the foundation of the refraction index variations of polyethylene glycol diacrylate (PEGDA) in the process of photopolymerization. The fabricated hollow microneedle exhibited ideal mechanical characteristics to penetrate the skin. Hydrodynamic simulations showed that the liquid was risen in a hollow microneedle by capillary force. Furthermore, a paper-based glucose sensor was integrated with the hollow microneedle. We also observed that the MN array smoothly extracted ISF in vitro and in vivo by capillary action. The outcomes displayed the applicability of the MN patch to persistent blood glucose (GLU) monitoring, diagnosis-related tests for patients and pre-diabetic individuals. [ABSTRACT FROM AUTHOR]

In recent years, the wide application of deep neural network models has brought serious risks of intellectual property rights infringement. Embedding a watermark in a network model is an effective solution to protect intellectual property rights. Although researchers have proposed schemes to add watermarks to models, they cannot prevent attackers from adding and overwriting original information, and embedding rates cannot be quantified. Therefore, aiming at these problems, this paper designs a high embedding rate and tamper-proof watermarking scheme. We employ wet paper coding (WPC), in which important parameters are regarded as wet blocks and the remaining unimportant parameters are regarded as dry blocks in the model. To obtain the important parameters more easily, we propose an optimized probabilistic selection strategy (OPSS). OPSS defines the unimportant-level function and sets the importance threshold to select the important parameter positions and to ensure that the original function is not affected after the model parameters are changed. We regard important parameters as an unmodifiable part, and only modify the part that includes the unimportant parameters. We selected the MNIST, CIFAR-10, and ImageNet datasets to test the performance of the model after adding a watermark and to analyze the fidelity, robustness, embedding rate, and comparison schemes of the model. Our experiment shows that the proposed scheme has high fidelity and strong robustness along with a high embedding rate and the ability to prevent malicious tampering. [ABSTRACT FROM AUTHOR]

Microfluidic paper-based analytical devices (µPADs) represent one of the promising green analytical strategies for low-cost and simple determination of various analytes. The actual task is the development of such devices for quantitation of antioxidants, e.g., flavonoids. In this paper, possibilities of a novel three-reagent µPAD including silver nitrate, 4-nitrophenyldiazonium tetrafluoroborate, and iron(III) chloride as reagents are assessed with respect to the determination of dihydroquercetin. It is shown that all the three reagents produce different colorimetric responses that can be detected by a mini-spectrophotometer–monitor calibrator or by a smartphone. The method is applicable to direct measuring high contents of dihydroquercetin (the linearity range is 0.026–1 mg mL−1, and the limit of detection is 7.7 µg mL−1), which is favorable for many dietary supplements. The analysis of a food supplement was possible with the relative standard deviations of 9–26%, which is satisfactory for quantitative and semiquantitative determinations. It was found that plotting a calibration graph in 3D space of the three reagents' responses allows us to distinguish dihydroquercetin from its close structural analogue, quercetin. [ABSTRACT FROM AUTHOR]

By focusing our attention on nitrogen components in plants, which are important for cultivation management in data-driven agriculture, we developed a simple, rapid, non-chemical and simultaneous quantification method for proteinic and nitrate nitrogen in a leaf model based on near-infrared (NIR) spectroscopic information obtained using a compact Fourier Transform NIR (FT-NIR) spectrometer. The NIR spectra of wet leaf models impregnated with a protein–nitric acid mixed solution and a dry leaf model obtained by drying filter paper were acquired. For spectral acquisition, a compact MEMS (Micro Electro Mechanical Systems) FT-NIR spectrometer equipped with a diffuse reflectance probe accessory was used. Partial least square regression analysis was performed using the spectral information of the extracted absorption bands based on the determination coefficients between the spectral absorption intensities and the contents of the two-dimensional spectral analysis between NIR and mid-infrared spectral information. Proteinic nitrogen content in the dry leaf model was well predicted using the MEMS FT-NIR spectroscopic method. Additionally, nitrate nitrogen in the dry leaf model was also determined by the provided method, but the necessity of adding the data for a wider range of nitric acid concentrations was experimentally indicated for the prediction of nitrate nitrogen content in the wet leaf model. Consequently, these results experimentally suggest the possibility of the application of the compact MEMS FT-NIR for obtaining the bioinformation of crops at agricultural on-sites. [ABSTRACT FROM AUTHOR]

This Special Issue compiles papers submitted by the Editorial Board Members of the Vehicular Sensing Section and outstanding scholars in this field. Thus, this paper proposes a deep learning approach, which consists of a two-stage process using an autoencoder and long short-term memory, to detect anomalies in electrical power steering sensor data. The presented topics range from physical models and components to advanced control systems for automated vehicles, including driver monitoring, comfort considerations, communication and cooperative systems, perception sensors and solutions to issues related to electric vehicles. The authors test these types of sensors under different weather conditions and employ fake targets between the sensor and the tracked vehicle. [Extracted from the article]

Internet of Things (IoT) architectures generally focus on providing consistent performance and reliable communications. The convergence of IoT, edge, fog, and cloud aims to improve the quality of service of applications, which does not typically emphasize energy efficiency. Considering energy in IoT architectures would reduce the energy impact from billions of IoT devices. The research presented in this paper proposes an optimization framework that considers energy consumption of nodes when selecting a node for processing an IoT request in edge-fog-cloud layered architecture. The IoT use cases considered in this paper include smart grid, autonomous vehicles, and eHealth. The proposed framework is evaluated using CPLEX simulations. The results provide insights into mechanisms that can be used to select nodes energy-efficiently whilst meeting the application requirements and other network constraints in multi-layered IoT architectures. [ABSTRACT FROM AUTHOR]

The detection of hydrogen peroxide and the control of its concentration are important tasks in the biological and chemical sciences. In this paper, we developed a simple and quantitative method for the non-enzymatic detection of H2O2 based on the selective etching of Au@Ag nanorods with embedded Raman active molecules. The transfer of electrons between silver atoms and hydrogen peroxide enhances the oxidation reaction, and the Ag shell around the Au nanorod gradually dissolves. This leads to a change in the color of the nanoparticle colloid, a shift in LSPR, and a decrease in the SERS response from molecules embedded between the Au core and Ag shell. In our study, we compared the sensitivity of these readouts for nanoparticles with different Ag shell morphology. We found that triangle core–shell nanoparticles exhibited the highest sensitivity, with a detection limit of 10−4 M, and the SERS detection range of 1 × 10−4 to 2 × 10−2 M. In addition, a colorimetric strategy was applied to fabricate a simple indicator paper sensor for fast detection of hydrogen peroxide in liquids. In this case, the concentration of hydrogen peroxide was qualitatively determined by the change in the color of the nanoparticles deposited on the nitrocellulose membrane. [ABSTRACT FROM AUTHOR]

Engine oil oxidation is one of the major reasons for oil aging which can result in variations in the physical and chemical properties of oil. Organic acids generated by oil oxidation can react with water to form inorganic acids and acidic substances (including organic and inorganic acids) that corrode engine parts, resulting in the generation of rust or damage to engine parts. This is one of the important reasons why oil should be regularly changed. One of the most commonly applied methods for judging the aging degree of engine oil is monitoring its acid number (AN). However, generally, the effect of oil water content on acid value measurement is not considered. When oils are used in engines, they are often contaminated by water due to condensation, which accelerates engine oil aging. Therefore, it is crucial to explore the water content effect on AN in the process of engine oil aging. In this research, a water content sensor was applied to characterize moisture content in oxidized oil samples. The sensor could also obtain oil sample electrical conductivity which corresponded to its dielectric constant. Using a mid-infrared spectrometer to measure oil sample AN at this point to obtain the variation in AN with oxidation time, oil sample AN was connected in series with the water content, dielectric constant and electrical conductivity. These parameters were monitored through sensors, and the effect of water content on AN was studied. Experimental results revealed that with the increase in oxidation time, the water content, electrical conductivity, dielectric constant increase and AN of oil were increased. At the same time, since the temperature had a greater effect on electrical conductivity, the application of an air-conditioned constant-temperature environment removed the effect of temperature change on electrical conductivity. [ABSTRACT FROM AUTHOR]

In this work, the authors explored the interaction of a suite of fluorescent zinc complexes with H2S. The authors provide evidence that HS− binds the zinc center of all the complexes under investigation, allowing them to possibly function as sensors by a 'coordinative-based' approach. Naked-eye color changes occur when treating the systems with HS−, so the fluorescence responses are modulated by the presence of HS−, which has been related to a change in the energy level and coupling of excited states through a computational study. The results show the potential of the systems to function as HS−/H2S colorimetric and fluorescent sensors. Paper-strip-based sensing experiments foresee the potential of using this family of complexes as chemosensors of HS− in more complex biological fluids. [ABSTRACT FROM AUTHOR]

Handwritten signatures are widely used for identity authorization. However, verifying handwritten signatures is cumbersome in practice due to the dependency on extra drawing tools such as a digitizer, and because the false acceptance of a forged signature can cause damage to property. Therefore, exploring a way to balance the security and user experiment of handwritten signatures is critical. In this paper, we propose a handheld signature verification scheme called SilentSign, which leverages acoustic sensors (i.e., microphone and speaker) in mobile devices. Compared to the previous online signature verification system, it provides handy and safe paper-based signature verification services. The prime notion is to utilize the acoustic signals that are bounced back via a pen tip to depict a user's signing pattern. We designed the signal modulation stratagem carefully to guarantee high performance, developed a distance measurement algorithm based on phase shift, and trained a verification model. In comparison with the traditional signature verification scheme, SilentSign allows users to sign more conveniently as well as invisibly. To evaluate SilentSign in various settings, we conducted comprehensive experiments with 35 participants. Our results reveal that SilentSign can attain 98.2 % AUC and 1.25 % EER. We note that a shorter conference version of this paper was presented in Percom (2019). Our initial conference paper did not finish the complete experiment. This manuscript has been revised and provided additional experiments to the conference proceedings; for example, by including System Robustness, Computational Overhead, etc. [ABSTRACT FROM AUTHOR]

Capacitive equipment refers to its insulation design using the principle of capacitance of electrical equipment, mainly by a variety of different capacitive components in series. Most of the equipment in the substation is capacitive equipment. Once an insulation failure occurs, it will lead to extremely serious consequences. Monitoring grid overvoltage and insulation degradation of capacitive equipment is an effective means to ensure the stable operation of the power system. Therefore, in order to enhance the health management of capacitive equipment, including transformers, bushings, and current transformers, and to mitigate the risk of severe failures, it is imperative to conduct broad-spectrum frequency-domain online monitoring of overvoltages, dielectric losses, and partial discharge. However, the current monitoring work requires the utilization of multiple detection apparatuses. Aiming at the disadvantage that the existing inspection is not well integrated and requires a combination of multiple devices. This paper proposes a smart grid overvoltage identification system that utilizes partial discharge (PD) signals in correlation with dielectric loss detection. The system achieves synchronous detection of dielectric loss and high-frequency partial discharge by synchronously and in real-time acquiring four current signals from the power grid, enhancing the integration level of the hardware system. [ABSTRACT FROM AUTHOR]

Photochromic inks have shown disadvantages, such as poor durability and high cost. Self-healable hydrogels have shown photostability and durability. Herein, a viologen-based covalent polymer was printed onto a paper surface toward the development of a multi-stimuli responsive chromogenic sheet with thermochromic, photochromic, and vapochromic properties. Viologen polymer was created by polymerizing a dialdehyde-based viologen with a hydroxyl-bearing dihydrazide in an acidic aqueous medium. The viologen polymer was well immobilized as a colorimetric agent into a polyvinyl alcohol (PVA)/tricarboxy cellulose (TCC)-based self-healable hydrogel. The viologen/hydrogel nanocomposite films were applied onto a paper surface. The coloration measurements showed that when exposed to ultraviolet light, the orange layer printed on the paper surface switched to green. The photochromic film was used to develop anti-counterfeiting prints using the organic hydrogel composed of a PVA/TCC composite and a viologen polymer. Reversible photochromism with strong photostability was observed when the printed papers were exposed to UV irradiation. A detection limit was monitored in the range of 0.5–300 ppm for NH3(aq). The exposure to heat (70 °C) was found to reversibly initiate a colorimetric change. [ABSTRACT FROM AUTHOR]