Search

In this study, actual swage waste activated sludge in batch reactors was employed to assess the synergistic effect of free nitrous acid and Fenton pre-treatments on enhancing methane production in the anaerobic digestion process. In addition to methane enhancement, the mechanisms driving the enhancement were also investigated via measuring enzymes activity and solubilisation of organic matter. This study revealed that the combined pre-treatments solubilised organic matter significantly more than the bioreactors pre-treated with individual FNA and Fenton. For understanding the influence of pre-treatments on solubilisation of organic matter, soluble protein, soluble polysaccharide and soluble chemical oxygen demand (SCOD) were measured before and after the treatments and it was shown that they respectively increased by 973%, 33% and 353% after the treatments. Protease and cellulase activity, as the key constituents of the microbial community in activated sludge, decreased considerably after the combined pre-treatments 42% and 32% respectively, which resulted in considerable methane enhancement. The results corroborate the synergy of the combined FNA and Fenton pre-treatment in degrading the organic and microbial constituents in waste activated sludge, paving the way for the big-scale implementation of these technologies.

The soda ash industry is a part of the chemical industry, which is responsible for the production of sodium carbonate, calcium chloride, absorbent masses, evaporated wet salt, food salt, pickling salt or salt tablets. During manufacturing of those products, strongly alkaline wastewater is generated. It could be characterised by a high electrolytic conductivity and concentration of ions: chlorides, sulfates, phosphates, calcium, sodium, magnesium, potassium and ammonium. The aim of the research was to test the effectiveness of removing sodium, potassium, calcium, magnesium and ammonium from wastewater after production of soda ash by three sorbents: Halosorb, Compakt and Damsorb K. The process was carried out using dynamic method with different flow of wastewater through the column with sorbent. It allowed to reduce concentrations of all cations tested. Moreover, it was found that sorbent type did not significantly affect the removal of any of the ions, but the deposit load had significant impact on the removal of all ions tested.

The aim of this work was to enhance the biodiesel quality and hydrocarbon content of green microalga B. braunii strain KMITL 2 cultivated outdoor under several salinity conditions in a batch production. The enhancement would be such that the microalgal biodiesel qualities met or exceeded the current standard so that it would be a good raw material for biodiesel production. The microalga production was in 300 L open oval ponds, among various salinity levels tested (0–20 ppt), 5 ppt was the best for hydrocarbon production, yielding 54.2 ± 0.9% hydrocarbon content and 5.1 ± 0.4 g L−1 biomass. As the microalga production was scaled up by cultivation in 3,675 L open raceway pond under the 5 ppt condition, the microalga yielded a bit higher hydrocarbon content (58.8 ± 2.9%) but much lower biomass (2.5 ± 0.5 g L−1). The production in both oval and raceway ponds yielded a nearly identical biodiesel property (61.06–67.42 cetane number) which exceeded the value specified in international standards. Therefore, it was concluded that B. braunii strain KMITL 2 can be batch cultivated in an open pond at optimum salinity to yield sufficient hydrocarbon and biomass for biodiesel production.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Sugarcane bagasse is a significant renewable energy source for the sugar and bioethanol industries. Bagasse ash is the waste from the combustion process and is mostly disposed of as landfill. Only a small quantity of bagasse ash is utilized as pozzolan in concrete, and a considerable quantity is left unused due to its high carbon and crystallite content. Generally, bagasse ash is rich in silica (SiO2), and it is thus an alternative source for silica extraction. In this paper, a low-energy and low-chemical consumption method is proposed to obtain silica from bagasse ash using alkali extraction and acid precipitation. The physical and chemical properties of the extracted silica are described. A silica yield of 80% and moisture absorption of 73% were achieved. The silica had amorphous phases and was light gray in color owing to the presence of carbon from incomplete combustion. Bagasse silica was used as an extender filler in an expensive photochromic pigment to increase the bulk volume. It was found that a pigment-to-silica mass ratio up to 1:10 could be used for thick-layer painting. However, a ratio of up to 1:3 is recommended for thin-layer screen-printing on fabrics. The bagasse ash silica-pigment blends have very good color fastness when washing; however, frequent aggressive washing should be avoided.

This work presents an alternative method for fabricating Li-ion electrodes in which the use of aluminum/copper current collectors and expensive binders is avoided. Low-cost natural cellulose fibers with a 2-mm length are employed as binder and support for the electrode. The objective of this method is to eliminate the use of heavy and inactive current collector foils as substrates and to replace conventional costly binders with cellulose fibers. Moreover, no harmful solvents, such as N-methylpyrrolidone, are employed for film fabrication. Water-soluble carbons are also utilized to reduce the preparation time and to achieve a better repartition of carbon in the electrode, thus improving the electrochemical performance. Flexible and resistant LiFePO4 (LFP), Li4Ti5O12 (LTO), organic 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA), and graphite electrodes are obtained with active mass loadings similar to those obtained by the current casting method. The initial discharge capacity of approximately 130 mAh·g−1 at 2 C is obtained for an LFP/LTO paper battery with an approximately 91.6% capacity retention after 1000 cycles. An all-organic prelithiated PTCDA/graphite cell without a transition metal is prepared and electrochemically tested. It is one of the first self-standing batteries that is composed of organic redox active molecules and biodegradable components reported in literature.

The prevention of decrease of quality caused by microbial activity in footwear materials entails the use of biocides. However, these substances may pose a hazard to humans and to the natural environment. The paper presents the results of antimicrobial effect investigation for cowhide leather treated with oregano oil. In these studies oil was applied by spraying onto the finished leather surface and examined to determine its antimicrobial activity by using the Agar Diffusion Plate Test. These results were compared with those where a cowhide leather was treated with oil at the stage of fatliquoring. In addition, the oregano oil toxicity level was assessed and compared with biocides used in the tanning industry. Introducing oregano oil into the leather at the stage of fatliquoring provides a better antimicrobial effect than by spraying, however hygienic finishing of leather can be obtained by introducing oil into the raw material by these both methods. The oregano oil is characterised by the lowest number of hazards and toxicity as compared with commercial biocides. The use of essential oils as natural biocides in the tanning industry seems to be especially important and suitable solution considering the harmful effects of synthetic biocides to humans and the environment.

Cellulose nanofiber (CNF) with high crystallinity has great mechanical stiffness and strength. However, its length is too short to be used for fibers of environmentally friendly structural composites. This paper presents a fabrication process of cellulose long fiber from CNF suspension by spinning, stretching and drying. Isolation of CNF from the hardwood pulp is done by using (2, 2, 6, 6-tetramethylpiperidine-1-yl) oxidanyl (TEMPO) oxidation. The effect of spinning speed and stretching ratio on mechanical properties of the fabricated fibers are investigated. The modulus of the fabricated fibers increases with the spinning speed as well as the stretching ratio because of the orientation of CNFs. The fabricated long fiber exhibits the maximum tensile modulus of 23.9 GPa with the maximum tensile strength of 383.3 MPa. Moreover, the fabricated long fiber exhibits high strain at break, which indicates high toughness. The results indicate that strong and tough cellulose long fiber can be produced by using ionic crosslinking, controlling spinning speed, stretching and drying.

The fluctuation of domestic wastewater characteristic inhibits the current conventional microbial-based treatment. The bioremediation fungi has received attention and reported to be an effective alternative to treat industrial wastewater. Similar efficient performance is envisaged for domestic wastewater whereby assessed performance of fungi for varying carbon-to-nitrogen ratios in domestic wastewater is crucial. Thus, the performance of pre-grown wild-Serbian Ganoderma lucidum mycelial pellets (GLMPs) was evaluated on four different synthetic domestic wastewaters under different conditions of initial pH (pH 4, 5, and 7) and chemical oxygen demand (COD) to nitrogen (COD/N) ratio of 3.6:1, 7.1:1, 14.2:1, and 17.8:1 (C3.6N1, C7.1N1, C14.2N1, and C17.8N1). The COD/N ratios with a constant concentration of ammonia–nitrogen (NH3–N) were chosen on the basis of the urban domestic wastewater characteristics sampled at the inlet basin of a sewage treatment plant (STP). The parameters of pH, COD, and NH3–N were measured periodically during the experiment. The wild-Serbian GLMPs efficiently removed the pollutants from the synthetic sewage. The COD/N ratio of C17.8N1 wastewater had the best COD and NH3–N removal, as compared to the lower COD/N ratio, and the shortest treatment time was obtained in an acidic environment at pH 4. The highest percentage for COD and NH3–N removal achieved was 96.0% and 93.2%, respectively. The results proved that the mycelium of GLMP has high potential in treating domestic wastewater, particularly at high organic content as a naturally sustainable bioremediation system.

High volumes of formation water comprising of complex mixture of hydrocarbons is generated during crude oil exploration. Owing to ecotoxicological concerns, the discharge of the formation water without remediation of hydrocarbonaceous pollutants is not permitted. Keeping this into mind, we carried out phycoremediation of hydrocarbons in formation water so that it can be safely discharged or re-used. For this, a native algal species was isolated from formation water followed by its morphological and 18S ribosomal RNA based identification confirming the algal isolate to be Chlorella vulgaris BS1 (NCBI GenBank Accession No. MH732950). The algal isolate exhibited high biomass productivity of 1.76 gm L−1 d−1 (specific growth rate: 0.21 d−1, initial inoculum: 1500 mg L−1) along with remediation of 98.63% petroleum hydrocarbons present in formation water within 14 days of incubation indicating an efficient hydrocarbon remediation process. Concomitantly, the hydrocarbon remediation process resulted in reduction of 75% Chemical Oxygen Demand (COD) load and complete removal of sulfate from formation water making it suitable for safe disposal or reuse as oil well injection water respectively. The present process overcomes the bottlenecks of external growth nutrient addition or dilution associated with conventional biological treatment resulting in a practically applicable and cost-effective technology for remediation of oil field formation water.

Biomass-based fly ash and wastewater are undesired products of the pulping industry. Recently, the use of biomass-based fly ash as an adsorbent (i.e., a valued material) for constituents of wastewater effluents was reported. In this work, the settling performance and properties of activated sludge were studied in the presence of fly ash. Upon mixing, fly ash increased the zeta potential of the sludge from −31 mV to −28 mV, which was due to the release of cationic ions from fly ash in the sludge suspension. The sludge settling and its flocculation affinity were improved through the complexation of flocs and released cation ions from fly ash. The relationships between the protein/polysaccharide (PN/PS) ratio and the content of extracellular polymeric substances (EPS) as well as the ratio and the properties of the sludge flocs were determined. A correlation between the total loosely bound-EPS (LB-EPS) content and the effluent suspended solids (ESS) (Pearson’s coefficient, rp = 0.83) was observed. The performance of sludge flocculation and settling were much more closely correlated with LB-EPS than with tightly bound EPS (TB-EPS). Scanning electron microscopy (SEM) analysis of sludge flocs before and after EPS extraction showed that the sludge flocs contained a large number of microorganisms, mainly Bacillus and Cocci. The amount of LB-EPS had an adverse influence on bioflocculation, effluent clarification and sludge settling affinity. The sludge properties had a moderate relationship with the PN/PS ratio of LB-EPS. Also, no correlation could be established between the ratio and the TB-EPS content.

Low permeability oil reservoirs are a widespread petroleum reservoir type all over the world. Therefore, methods to recover these reservoirs efficiently are of importance to guarantee energy supply. Here we report our novel stimulation of indigenous microbes by optimizing the water cut in low permeability reservoirs for green and enhanced oil recovery. We aimed to investigate the characteristics of indigenous bacterial communities with changes in water cut in reservoirs by high-throughput sequencing technology, and reveal the mechanism and characteristics of the crude oil biotreatment under different crude oil-water ratio conditions and the optimum activation time of indigenous functional microbial groups in reservoirs. The indigenous microbial metabolism products were characterized by gas chromatography mass spectrometry. Results showed that Acinetobacter (47.1%) and Pseudomones (19.8%) were the main functional genus of crude oil degradation at the optimal activation time, and can reduce the viscosity of crude oil from 8.33 to 5.75 mPa·s. The dominant bacteria genus for oil recovery after activation of the production fluids was similar to those in the reservoirs with water cut of 60–80%. Furthermore seven mechanism pathways of enhancing oil recovery by the synergistic of functional microbial groups and their metabolites under different water cut conditions in low permeability reservoirs have been established.

Industrial scale-up of microalgal cultures is often a protracted step prone to culture collapse and the occurrence of unwanted contaminants. To solve this problem, a two-stage scale-up process was developed – heterotrophically Chlorella vulgaris cells grown in fermenters (1st stage) were used to directly inoculate an outdoor industrial autotrophic microalgal production unit (2nd stage). A preliminary pilot-scale trial revealed that C. vulgaris cells grown heterotrophically adapted readily to outdoor autotrophic growth conditions (1-m3 photobioreactors) without any measurable difference as compared to conventional autotrophic inocula. Biomass concentration of 174.5 g L−1, the highest value ever reported for this microalga, was achieved in a 5-L fermenter during scale-up using the heterotrophic route. Inocula grown in 0.2- and 5-m3 industrial fermenters with mean productivity of 27.54 ± 5.07 and 31.86 ± 2.87 g L−1 d−1, respectively, were later used to seed several outdoor 100-m3 tubular photobioreactors. Overall, all photobioreactor cultures seeded from the heterotrophic route reached standard protein and chlorophyll contents of 52.18 ± 1.30% of DW and 23.98 ± 1.57 mg g−1 DW, respectively. In addition to providing reproducible, high-quality inocula, this two-stage approach led to a 5-fold and 12-fold decrease in scale-up time and occupancy area used for industrial scale-up, respectively.

Sludge bulking is a major problem that restricts the development of the activated sludge process. The microbial community responsible for sludge bulking varies depending on water quality and operational conditions. This study analysed the microbial community of bulking sludge in oxidation ditch with ultra-low sludge loading and long sludge retention time using high-throughput sequencing. The study found that the relative abundance of bacterial genus Saprospiraceae_norank was the highest in bulking sludge, reaching 13.39–28.83%, followed by Comamonadaceae_unclassified, Ardenticatenia_norank and Tetrasphaera, with the relative abundance of 4.59–11.08%, 0.52–16.60% and 0.17–8.92% respectively. In contrast, the relative abundance of bacteria that easily caused sludge bulking including Microthrix (0.54–2.47%), Trichococcus (0.32–1.71%), Gordonia (0.14–1.28%), and Thiothrix (0.01–0.06%) were relatively low. Saprospiraceae_norank was predominant and induced sludge bulking in oxidation ditch. The relative abundance of fungal genus Trichosporon was the highest in bulking sludge, reaching 16.95–24.98%, while other fungal genera were Saccharomycetales_unclassified (5.59–14.55%), Ascomycota_norank (1.45–13.51%), Galactomyces (5.23–11.23%), and Debaryomyces (7.69–9.42%), whereas Trichosporon was the dominant fungal genus in bulking sludge. This study reported that excessive Saprospiraceae_norank can induce sludge bulking for the first time, which provides important knowledge to control sludge bulking.

Whisky, as a high value product, is often adulterated, with adverse economic effects for both producers and consumers as well as potential public health impacts. Here we report the use of DAPCI-MS to analyse and chemically profile both genuine and counterfeit whisky samples employing a novel ‘direct from the bottle’ methodology with zero sample pre-treatment, zero solvent requirement and almost no sample usage. 25 samples have been analysed from a collection of blended Scotch whisky (n = 15) and known counterfeit whisky products (n = 10). Principal component analysis has been applied to dimensionally reduce the data and discriminate between sample groups. Additional chemometric modelling, a partial least squares regression, has correctly classified samples with 92% success rate. DAPCI-MS shows promise for simple, fast and accurate counterfeit detection with potential for generic aroma profiling and process quality monitoring applications.

To conserve freshwater resources, domestic and industrial wastewater is recycled. Algal systems have emerged as an efficient, low-cost option for treatment (phycoremediation) of nutrient-rich wastewater and environmental protection. However, industrial wastewater may contain growth inhibitory compounds precluding algal use in phycoremediation. Therefore, extremophyte strains, which thrive in hostile environments, are sought-after. Here, we isolated such an alga - a strain of Synechocystis sp. we found to be capable of switching from commensal exploitation of the nitrogen-fixing Trichormus variabilis, for survival in nitrogen-deficient environments, to free-living growth in nitrate abundance. In nitrogen depletion, the cells are tethered to polysaccharide capsules of T. variabilis using nanotubular structures, presumably for nitrate acquisition. The composite culture failed to establish in industrial/domestic waste effluent. However, gradual exposure to increasing wastewater strength over time untethered Synechocystis cells and killed off T. variabilis. This switched the culture to a stress-acclimated monoculture of Synechocystis sp., which rapidly grew and flourished in wastewater, with ammonium and phosphate removal efficiencies of 99.4% and 97.5%, respectively. Therefore, this strain of Synechocystis sp. shows great promise for use in phycoremediation, with potential to rapidly generate biomass that can find use as a green feedstock for valuable bio-products in industrial applications.

Ag-LaFeO3 molecularly imprinted polymers (ALMIPs) were fabricated, which provided special recognition sites to methanol. Then ALMIPs fiber 1, fiber 2 and fiber 3 were prepared using filter paper, silk and carbon fibers template, respectively. Based on the observation of X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Nitrogen adsorption surface area analyzer (BET), the structure, morphology and surface area of the fibers were characterized. The ALMIPs fibers (fiber 1, fiber 2 and fiber 3) show excellent selectivity and good response to methanol. The responses to 5 ppm methanol and the optimal operating temperature of ALMIPs fibers are 23.5 and 175 °C (fiber 1), 19.67 and 125 °C (fiber 2), 17.59 and 125 °C (fiber 3), and a lower response (≤10, 3, 2) to other test gases including formaldehyde, acetone, ethanol, ammonia, gasoline and benzene was measured, respectively.

In this paper, α-Fe2O3 nanoparticles (NPs)-reduced graphene oxide (RGO), α-FeOOH nanorods (NRs)-RGO and porous α-Fe2O3 NRs-RGO could be selectively synthesized by hydrothermal method. The investigations indicated that the obtained α-Fe2O3 NPs, α-FeOOH NRs and porous α-Fe2O3 NRs were either attached on the surface of RGO sheets or coated uniformly by the RGO sheets. And the as-prepared nanohybrids exhibited excellent microwave absorption performance, which was proved to be ascribed to the quarter-wavelength matching model. The optimum reflection loss (RL) values for α-Fe2O3 NPs-RGO, α-FeOOH NRs-RGO and porous α-Fe2O3 NRs-RGO were ca. −32.3, −37.4 and −71.4 dB, respectively. Moreover, compared to the obtained α-Fe2O3 NPs-RGO and α-FeOOH NRs-RGO, the as-prepared porous α-Fe2O3 NRs-RGO nanohybrids exhibited enhanced microwave absorption properties because of their special structure and synergetic effect. The possible enhanced microwave absorption mechanisms were discussed in details. Our results confirmed that the geometrical morphology had a great influence on their microwave absorption properties, which provided a promising approach to exploit high performance microwave absorbing materials.

Polyphenols based bioactive compounds from vegetables and fruits are known for impressive antioxidant activity. Ingestion of these antioxidants may promote human health against cardiovascular diseases and cancer. Mango is a popular tropical fruit with special taste, high nutritional value and health-enhancing metabolites. The aim was to investigate the diversity of phytochemicals between two mango cultivars of china at three stages of fruit maturity. We used ESI-QTRAP-MS/MS approach to characterize comprehensively the metabolome of two mango cultivars named Hongguifei (HGF) and Tainong (TN). HPLC was used to quantify selected catechin based phenolic compounds. Moreover, real-time qPCR was used to study the expression profiles of two key genes (ANR and LAR) involved in proanthocyanidin biosynthesis from catechins and derivatives. A total of 651 metabolites were identified, which include at least 257 phenolic compounds. Higher number of metabolites were differentially modulated in peel as compared to pulp. Overall, the relative quantities of amino acids, carbohydrates, organic acids, and other metabolites were increased in the pulp of TN cultivar. While the contents of phenolic compounds were relatively higher in HGF cultivar. Moreover, HPLC based quantification of catechin and derivatives exhibited cultivar specific variations. The ANR and LAR genes exhibited an opposite expression profile in both cultivars. Current study is the first report of numerous metabolites including catechin-based derivatives in mango fruit. These findings open novel possibilities for the use of mango as a source of bioactive compounds.

Made available in DSpace on 2021-06-25T10:15:02Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-12-01 The adoption of dicamba-tolerant soybean varieties has increased the concern and demand for new drift and volatility reduction technologies. Potential spray nozzles and adjuvants should be studied to determine its effects on drift and volatility of dicamba tank-mixtures. The objective of this study was to evaluate physicochemical characteristics of spray solutions containing dicamba; to analyze droplet size effect with air induction nozzles; and to assess dicamba volatilization on soybean plants with a proposed methodology. Treatments included dicamba only and mixtures with herbicides and adjuvants. Dicamba mixed with lecithin + methyl soybean oil + ethoxylated alcohol adjuvant had the greatest efficacy potential among treatments considering tank-mixture pH, surface tension, contact angle and droplet size. The MUG11003 nozzle produced the coarsest droplet size and was better suited for drift management among nozzle types. The proposed volatilization methodology successfully indicated dicamba volatilization in exposed soybean plants and among the evaluated treatments, it showed greater volatilization for dicamba with glyphosate + lecithin + propionic acid adjuvant. Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus

Fuels and their components accumulate in soil, and many soil organisms are exposed to this pollution. Compared to intensive research on the effect of conventional fuel on soil, very few studies have been conducted on soil ecotoxicity of biofuels. Considering the limited information available, the present study evaluated the changes caused by the presence of biodiesel and diesel fuel in soil. The reaction of higher plants and soil organisms (microbial communities and invertebrates) was analysed. Conventional diesel oil and two types of biodiesel (commercial and laboratory-made) were introduced into the soil. Two levels of contamination were applied—5 and 15% (w/w per dry matter of soil). The plate method was used to enumerate microorganisms from soil contaminated with biodiesel and diesel fuel. Phytotoxicity tests were conducted by a 3-day bioassay based on the seed germination and root growth of higher plant species (Sorghum saccharatum and Sinapis alba). Fourteen-day ecotoxicity tests on earthworm were performed using Eisenia fetida. Based on the results of the conducted tests it was found out that the organisms reacted to the presence of fuels in a diverse manner. As to the microorganisms, both the growth and reduction of their number were noted. The reaction depended on the group of microorganisms, type of fuel and dose of contamination. The lipolytic and amylolytic microorganisms as well as Pseudomonas fluorescens bacteria were particularly sensitive to the presence of fuels, especially biodiesel. Fuels, even at a high dose, stimulated the growth of fungi. Monocotyledonous sugar sorghum plants were more sensitive to the presence of fuels than dicotyledonous white mustard. There was also a significant negative impact of contamination level on plant growth and development. Biodiesel, to a greater extent than conventional fuel, adversely affected the survival and volume of earthworms.

Cellulose nanofibers were obtained from the Colombian fique (Furcraea bedinghausii) and Acrylic hydrogels (H) and reinforced acrylic hydrogels with fique nanofibres (HRFN) were synthesized, using the solution polymerization method. The extraction was carried out using a combined extraction method (chemical procedures and ultrasound radiation). The raw material (NAT-F), bleached fibers (B-F), hydrolyzed fibers and fibers treated with ultrasound (US-F) were characterized by infrared spectroscopy (FTIR) and thermal stability analysis; also, in order to have a comparison criterion, a commercial microcrystalline cellulose sample (CC) was analyzed, which demonstrated the extraction of fique cellulose. The surface morphology of the NAT-F and the B-F was determined by scanning electron microscopy and the average particle size of the nanofibers was made through transmission electron microscopy. In H y HRFN the strain percent and compression resistance (Rc) were measured. The fique nanofibers showed diameter and length averages of 25.2 ± 6.2 nm and 483.8 ± 283.2 nm respectively. Maximum degradation temperature was 317 °C. HRFN presented higher compression resistance (16.39 ± 4.30 kPa) and this resistance was 2.5 greater than the resistance of H (6.49 ± 2.48 kPa). The results indicate that fique lignocellulosic matrix has potential application for obtaining polymeric type composite materials.

Accumulation of the Municipal Sewage Sludge (MSS) is considered as one of the most harmful renewable ecological and human health problems. MSS is a renewable resource that could be used as a soil organic amendment. This study aims to reduce the Heavy Metals (HMs) from the sludge content and sludge compost. Furthermore, this study is considered the first to assess the mycotoxins content in sludge and sludge compost via a new biological treatment using the fungus Serendipita indica or a mixture of lactic acid bacteria, thus providing safer nutrients for the soil amendment for a longer time and preserving human health. The HMs and mycotoxins were determined. The results exhibited that the biotic remediation of bio-solid waste and sewage sludge compost succeeded; a new bio-treated compost with a very low content of heavy metals and almost mycotoxins-free contents was availed. Also, the results indicated that the Lactobacilli mixture realized the best results in reducing heavy metals contents and mycotoxins. Afterward, S. indica. biotic remediation of bio-solid waste and sewage sludge compost minimized the health risk hazards affecting the human food chain, allowing for the different uses of sludge to be safer for the environment.

Microbial fuel cell (MFC) technology is a simple way to accelerate the treatment of the oily sludge which is a major problem affecting the quality of oil fields and surrounding environment while generating electricity. To investigate the oil removal and the characteristics of changes in the composition of bacteria, sediment microbial fuel cells (SMFCs) supplemented with oily sludge was constructed. The results showed that the degradation efficiency of total petroleum hydrocarbon (TPH) of SMFC treatment was 10.1 times higher than the common anaerobic degradation. In addition, the degradation rate of n-alkanes followed the order of high carbon number > low carbon number > medium carbon number. The odd–even alkane predominance (OEP) increased, indicating that a high contribution of even alkanes whose degradation predominates. The OUT number, Shannon index, AEC index, and Chao1 index of the sludge treated with SMFC (YN2) are greater than those of the original sludge (YN1), showing that the microbial diversity of sludge increased after SMFC treatment. After SMFC treatment the relative abundance of Chloroflexi, Bacteroidia and Pseudomonadales which are essential for the degradation of the organic matter and electricity production increased significantly in YN2. These results will play a crucial role in improving the performance of oily sludge MFC.

Lipids in sewage sludge are considered to be high-class raw materials for biodiesel or other valuable products. We profiled the characteristics and assessed the reutilization potential of lipids from different sludge sources, including sludge from the primary sedimentation tank (PST sludge) and sludge from the secondary sedimentation tank in a conventional activated sludge system (CAS sludge), as well as sludge from ultrashort-sludge retention time (SRT) activated sludge systems with different SRTs (USAS sludge, with SRTs of 0.5, 1.0, 2.0, 3.0 and 4.0 d). The results showed that the lipids in the sludges were mainly composed of cellular lipids, free fatty acids (FFAs), wax and gum. The highest lipid content was found in the PST sludge (156.8 ± 11.9 mg/g, dry basis), followed by the USAS sludges (67.9 ± 11.0–132.2 ± 11.8 mg/g) and the CAS sludge (46.0 ± 16.5 mg/g). Lipid species such as Cer, So, PE, PC, and TG were abundant, comprising over 80% of the cellular lipids in the sludges. With higher lipid contents, the PST sludge and USAS sludge (0.5 d SRT) were suggested to have a higher reutilization potential for use in producing biodiesel. In addition, the CAS sludge was promising for resource reutilization and energy recovery due to the large amount of excess sludge.

Sensor data can be wirelessly transmitted from simple, battery-less tags using Radio Frequency Identification (RFID). RFID sensor tags consist of an antenna, a radio frequency integrated circuit chip (RFIC), and at least one sensor. An ideal tag can communicate over a long distance and be seamlessly integrated onto everyday objects. However, miniaturized antenna designs often have lower performance. Here we demonstrate compact, flexible sensor tags with read range comparable to that of conventional rigid tags. We compare fabrication techniques for flexible antennas and demonstrate that screen and stencil printing are both suitable for fabricating antennas; these different techniques are most useful at different points in the design cycle. We characterize two versions of flexible, screen printed folded dipoles and a meandered monopole operating in the 915 MHz band. Finally, we use these antennas to create passive sensor tags and demonstrate over the air communication of sensor data. These tags could be used to form a network of printed, flexible, passive, interactive sensor tags.

Agricultural wastes, such as wheat bran and swine wastewater, were used for bioremediation of oil-contaminated soil. Two optimised strains that could degrade oil efficiently were selected. The result showed that the best ratio of strain A to strain B was 7:3. Swine wastewater could be a replacement for nitrogen source and process water for bioremediation. Next, the Box-Behnken design was used to optimise the culture medium, and the optimal medium was as follows: microbial dosage of 97 mL/kg, wheat bran of 158 g/kg and swine wastewater of 232 mL/kg. Under the optimal medium, the oil degradation rate reached 68.27 ± 0.71% after 40 d. The urease, catalase, and dehydrogenase activities in oil-contaminated soil all increased, and the microbe quantity increased significantly with manual composting. These investigations might lay a foundation for reducing the pollution of agricultural wastes, exploring a late model for bioremediation of oil-contaminated soil.

Two-stage anaerobic digestion of palm oil mill effluent (POME) is a promising method for converting the waste from the largest agricultural industry in Southeast Asia into a clean and sustainable energy. This study investigates the degradation of acid-rich effluent from the dark fermentation stage for the production of biomethane (BioCH4) in a 30-L continuous stirred-tank reactor (CSTR). The continuous methanogenic process was operated with varied HRTs (10 - 1 day) and OLRs (4.6–40.6 gCOD/L.d−1) under thermophilic conditions. Methanothermobacter sp. was the dominant thermophilic archaea that was responsible for the production rate of 4.3 LCH4/LPOME.d−1 and methane yield of 256.77 LCH4kgCOD at HRT of 2 d, which is the lowest HRT reported in the literature. The process was able to digest 85% and 64% of the initial POME’s COD and TSS, respectively. The formation of methane producing granules (MPG) played a pivotal role in sustaining the efficient and productive anaerobic system. We report herein that the anaerobic digestion was not only beneficial in reducing the contaminants in the liquid effluent, but generating BioCH4 gas with a positive net energy gain of 7.6 kJ/gCOD.

The methods of separation of microalgae has a significant impact in the economic aspects of their cultivation. In this study, pine bark was used as a substrate for immobilization of microalgal biomass cultivated in raw municipal sewage. The experiment was conducted in cylindrical photobioreactors (PBRs) with circulation of wastewater. Biomass was cultivated for 42 days. After that time, abundant growth of the biofilm with microalgae on the surface of pine bark as well as improvement of the quality of treated sewage were observed. The efficiency of removal of nutrients from wastewater was 64–81% for total nitrogen and 97–99% for total phosphorus. Moreover, the concentration of suspended solids in sewage was reduced, which resulted in a decrease in turbidity by more than 90%. Colorimetric analysis and Volatile Matter (VM) content in the substrate showed a decrease in the Higher Heating Value (HHV) and concentration of VM due to the proliferation of biofilm.

The industrial wastewater disposal has been growing attention for environmental protection and resource substitution, current decades. Similarly, the durability enhancement of concrete has increased attention by microbial induced CaCO3 precipitation (MICP) process (biocalcification). However, ecofriendly utilization of industrial wastewater in concrete formation is unstudied so far. The present study was carried out to evaluate the effect of industrial wastewater on the formation of cement mortar, compressive strength and water absorption. The biocement mortar strength (y) increased (y = 0.5295×2 + 1.6019×+251.05; R2 = 0.9825) with increasing percentage of organic wastewater (x) (BM0 – BM100) by MICP, where highest strength (280.75 kgf/cm2) was observed on BM100 (100% wastewater), compared to control (252.05 kgf/cm2). The water absorption (y) of biocement mortar decreases (y = −0.0251×2–0.103× + 15.965; R2 = 0.9594) with increment of wastewater (x) (%) (BM0 – BM100), where a minimum-water-absorption (14.42%) observed on BM100, compared to control (15.89%). SEM micrograph and XRD shows the formation of most-distinctive CaCO3 crystallization (aragonite/calcite) (acicular, brick shape, massive and stacked structure) inside biocement mortar (BM100), which fills the pores within cement mortar to form a denser structure, by microbial organic wastewater. Thus, present findings implied a cost-effective of MICP technology to improve the concrete properties along with the mitigation of industrial wastewater pollution, which goes some way towards solving the problem of industrial wastewater pollution.

Phytoremediation is one of the environmental-friendly and cost-effective systems for the treatment of wastewater, including industrial wastewater such as palm oil mill effluent final discharge (POME FD). However, the effects of the wastewater on the phytoremediator plants, in term of growth performance, lignocellulosic composition, and the presence of nutrients and heavy metals in the plants are not yet well studied. In the present work, we demonstrated that POME FD increased the growth of P. purpureum. The height increment of P. purpureum supplied with POME FD (treatment) was 61.72% as compared to those supplied with rain water (control) which was 14.42%. For lignocellulosic composition, the cellulose percentages were 38.77 ± 0.29% (treatment) and 34.16 ± 1.01% (control), and the difference was significant. These results indicated that POME FD could be a source of plant nutrients, which P. purpureum can absorb for growth. It was also found that the heavy metals (Al, As, Cd, Co, Cr, Ni and Pb) inside the plant were below the standard limit of the World Health Organization (WHO). Since POME FD was shown to have no adverse effects on P. purpureum, further research regarding the potential application of P. purpureum following phytoremediation of POME FD such as biofuel production is warranted to evaluate its potential use to fit into the waste-to-wealth agenda.

Mining is an essential human activity, but results in several environmental impacts, notably the contamination of ground and surface water through the presence of toxic substances such as metals and sulfates in mine drainage. Permeable reactive barriers (PRB) have been applied to remediate this environmental impact, but the high costs associated with the maintenance of this system are still a challenge. The main objective of this study was to evaluate the use of kraft pulp mill alkaline residues, known as dregs and grits, as material for PRB, and to determine their capacity for retaining copper and sulfate. The work was carried out in laboratory adsorption kinetics assays, batch assays and column tests. Tests for elemental characterization, point of zero charge, acid neutralization capacity, total porosity, bulk density and moisture of the dregs and grits were conducted. The results showed high retention of Cu due to a chemical precipitation mechanism, notably for dregs (99%) at 5 min in adsorption kinetics. The grits presented similar results after 180 min for the same assay. Sulfate retention was effective at pH below 5, with an efficiency of 79% and 89% for dregs and grits, respectively. Dregs presented the best results for acid drainage remediation, notably with a solid:liquid (S:L) ratio of 1:10.

Vegetable Market have become major sources of organic waste. Some of such waste when being diverted to landfills not only increase the landfill loading but also contribute to increase greenhouse gas emission. Of the many technologies available in handling such hugely generated waste, composting has proven very effective for decades. Enzyme and non-enzyme mediated aerobic composting of vegetable market complex waste (VMCW) have been investigated. Conventional composting technique though being capable of handling large quantum of waste are found to consume more time. Proven to be disadvantages factor. In the present investigation, the pre-cultured seed inoculums used for vegetable market complex waste, shortened the typical composting period from 45 to 9 days for the first time. Also, rapid size and volume reduction of VMCW was witnessed. The organic degradation of VMCW was observed as 42% (82 ± 2.83% to 40.82 ± 0.61%), with a volume reduction from 0.012m3 to 0.003 m3 within 9 days. An enriched nutrients NPK level of compost bio-fertilizer was recorded as 0.91% w/w, 0.5% w/w and 1.029% w/w respectively. Compost maturity observed through the X-ray diffraction (XRD) analysis of the manure confirmed the conversion of the crystal structure of the compost particle to amorphous form and the mineralization of organic matter during the composting. Thus, the fermented pre-cultured seed inoculums favored an enhanced nutrients level with shortened composting time.

Cannabidiol (CBD) has become a buzzword in many products that have bloomed on the market. The scientific community and some authorities have recently raised concerns on the quality of these products. In particular, the discrepancy between the labelled and the real content of cannabidiol in liquids for e-cigarettes seems to be emerging as a major issue. Furthermore, to-date no studies have been carried out on the chemical stability upon storage of these type of products. The aim of this work was to investigate the accuracy in labelling of thirteen commercially e-liquids containing CBD and the effects of different storage conditions on their quality. The results showed that only 38% of samples were labelled within a ±10% variance from their labels. Stability tests showed a maximum degradation of CBD when samples were stored at 37 °C for 30 days with average values up to 20%. The effect of light was lower but still significant with averages values up to 15% degradation after 30 days. In conclusion, we believe that health authorities should regulate and control this market more stringently to protect customers and their health. Furthermore, our stability tests have shown that if clear indications are provided on the best storage conditions, the quality of these products can be mostly preserved.

Ineffectiveness of the chemicals applied so far for waterlogged wood conservation created the need to develop new more, efficient and reliable agents. As an alternative, a new method with the use of organosilicon compounds differing in chemical composition and molecular weight has been investigated. The results obtained show the potential of organosilicons as consolidants in waterlogged wood conservation able to effectively stabilise wood dimensions upon drying. The best wood stabilisers were low-molecular organosilicons enable to penetrate the cell wall as well as chemicals with functional groups capable of interacting with wood polymers and forming stabilising coatings on the cell wall surface. The best anti-shrink efficiency values were obtained for (3-Mercaptopropyl)trimethoxysilane, (3-Aminopropyl)triethoxysilane, 1,3-Bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane, reaching 98, 91 and 91%, respectively. Most of the applied organosilicons reduced wood hygroscopicity, which limits the risk of further dimensional changes of wood exposed to a variable air moisture content and potentially reduces wood biodegradation. In the light of our studies, the proposed method of waterlogged wood conservation with organosilicons is potentially reversible in the case of siloxanes and amino-silanes as well as retreatable, which complies with the requirements of the conservation ethics.

The management of large amounts of eggshell waste annually produced in the world is problematic as generally this material is only disposed at landfills with odor production and microbial growth. On the contrary, significant environmental and economic advantages could be obtained transforming this biowaste into new value-added products. Eggshell biowaste was the starting material for the synthesis of hydroxyapatite by a simple and sustainable procedure and applied for the removal of Co2+ from aqueous solutions. The effects of contact time and initial metal concentration were investigated in batch experiments. Eggshell-based hydroxyapatite (ESHAP) before and after Co2+ removal was characterized by X-ray diffraction and scanning electron microscopy. The process was rapid and reached equilibrium within 80 min. The removal efficiency was in the range 70–80% which is generally higher than other waste-derived adsorbents. Adsorption of Co2+ on the surface of ESHAP particles and ion exchange with Ca2+ resulting in the formation of a Co-phosphate are the main mechanisms of the metal removal. The conversion of eggshell waste to a low-cost adsorbent for the treatment of metal contaminated waters could contribute to a more sustainable and effective management of this biowaste.

The enhancement of composting technology to stabilize sludge pretreated by ozonation and ultrasonic was tested for 35 days. Secondary sludge produced by biological process are characterized with endogenous residue and inert solid matter which inhibit fully degrade bacterial cell walls. The composting process was performed with sludge pretreated with ozonatian and ultrasonics and green waste in a ratio of 2:1. The composting characteristics was evaluated for different physico-chemical and microbiological parameters in five different reactors. A high degree of composting quality was achieved with respect to significant reduction in volatile solids (VS) (32%), total organic carbon (TOC) (35.0%), C/N ratio (23.74), total coliform (TC) (168) along with the substantial increase in availability of nutrients like N (1.2%) and P (8.77%). High removal efficiency of TC and Fecal Coliform (FC) were observed in composting results, where simultaneous ultrasonic and ozonation were considered as primary-stabilization process. Therefore, applying integrated ultrasonic/ozonation with composting system for sludge stabilization is potentially useful technology in sustainable land restoration practices to meet standards and produce soil conditioner.

The present work investigates biomass wastes and their ashes for re-use in combination with mineralised CO2 in cement-bound construction products. A range of biomass residues (e.g., wood-derived, nut shells, fibres, and fruit peels) sourced in India, Africa and the UK were ashed and exposed to CO2 gas. These CO2-reactive ashes could mineralise CO2 gas and be used to cement ‘raw’ biomass in solid carbonated monolithic composites. The CO2 sequestered in ashes (125–414 g CO2/kg) and that emitted after incineration (400–500 g CO2/kg) was within the same range (w/w). The CO2-reactive ashes embodied significant amounts of CO2 (147–424 g equivalent CO2/kg ash). Selected ashes were combined with raw biomass and Portland Cement, CEM 1 and exposed to CO2. The use of CEM 1 in the carbonated products was offset by the CO2 mineralised (i.e. samples were ‘carbon negative’, even when 10% w/w CEM 1 was used); furthermore, biomass ashes were a suitable substitute for CEM 1 up to 50% w/w. The approach is conceptually simple, scalable, and can be applicable to a wide range of biomass ashes in a closed ‘emission-capture’ process ‘loop’. An extrapolation of potential for CO2 offset in Europe provides an estimate of CO2 sequestration potential to 2030.

This study investigates the influence of inoculated and uninoculated aeration pretreatment on nutrients and phytotoxicity of anaerobic digestion (AD) effluent. Swine manure AD effluent was inoculated with activated and anaerobic sludge, respectively. Our results show that aeration with the addition of activated sludge could reduce the phytotoxicity of AD effluent. Compared to the control treatment without any sludge addition, the addition of activated sludge resulted in a more significant reduction in the AD effluent salinity, NH4+ content, and organic matter (indicated by the chemical oxygen demand) when AD effluent was aerated for less than 8 hours. As a result, a much higher seed germination index (GI) was observed for the treatment with activated sludge addition, particularly when aerated for 4–5 hours, contributing the gas/water ratio of 20:1–30:1. On the other hand, no significant differences in the nutrient contents and GI value were observed for the control treatment and that with the addition of anaerobic sludge. Results from this study shed light on optimizing the management of AD effluent for agricultural application.

Wood chips or particles as well as shredded straw offer desired thermal insulation qualities. When exposed to a humid environment, however, fungal growth on wood and straw is an important consideration. An experimental investigation was conducted in order to evaluate the effectiveness of a simple treatment in mitigating fungal growth on wood- and straw-based insulation. This treatment involved blending of wood chips or particles, or shredded straw with an aerated slurry which offers the potential to mitigate fungal growth on biomass by a combination of physical and chemical effects without imposing a weight penalty. Experimental results verified the effectiveness of this treatment in controlling fungal growth on wood and straw subjected to different moisture conditions.

Nitrous oxide (N2O) is formed during wastewater nitrogen removal processes. It is a strong greenhouse gas, however, if properly captured it can also be used as a renewable energy source. In this study, a nosZ-deficient strain of Pseudomonas aeruginosa was constructed. During growth under denitrifying conditions, the nosZ-deficient strain was more highly transcribing other genes from the denitrification pathway (narG, nirS, and norB) than the wild-type strain. This strain could also convert 85% of NO2−-N to N2O when it was grown with acetate compared to 2−-N concentrations (700 mg/L) was inoculated with this strain, the N2O conversion efficiencies were >73% and N2O comprised 73~81% of the biogas being generated. The energy yield from wastewater in bioaugmented reactors also reached levels as high as 1260 kJ/m3. These results are significant and show that bioaugmentation of reactors during denitrification treatment processes with nosZ-deficient strains of Pseudomonas or other core denitrifying bacteria might be an effective way to enhance N2O recovery.

Freshwater metazoan biodiversity assessment using environmental DNA (eDNA) captured on filters offers new opportunities for water quality management. Filtering of water in the field is a logistical advantage compared to transport of water to the nearest lab, and thus, appropriate filter preservation becomes crucial for maximum DNA recovery. Here, the effect of four different filter preservation strategies, two filter types, and pre-filtration were evaluated by measuring metazoan diversity and community composition, using eDNA collected from a river and a lake ecosystem. The filters were preserved cold on ice, in ethanol, in lysis buffer and dry in silica gel. Our results show that filters preserved either dry or in lysis buffer give the most consistent community composition. In addition, mixed cellulose ester filters yield more consistent community composition than polyethersulfone filters, while the effect of pre-filtration remained ambiguous. Our study facilitates development of guidelines for aquatic community-level eDNA biomonitoring, and we advocate filtering in the field, using mixed cellulose ester filters and preserving the filters either dry or in lysis buffer. © The Author(s) 2018. Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

To understand the seasonal variation of the activated sludge (AS) bacterial community and identify core microbes in different wastewater processing systems, seasonal AS samples were taken from every biological treatment unit within 4 full-scale wastewater treatment plants. These plants adopted A2/O, A/O and oxidation ditch processes and were active in the treatment of different types and sources of wastewater, some domestic and others industrial. The bacterial community composition was analyzed using high-throughput sequencing technology. The correlations among microbial community structure, dominant microbes and process performance were investigated. Seasonal variation had a stronger impact on the AS bacterial community than any variation within different wastewater treatment system. Facing seasonal variation, the bacterial community within the oxidation ditch process remained more stable those in either the A2/O or A/O processes. The core genera in domestic wastewater treatment systems were Nitrospira, Caldilineaceae, Pseudomonas and Lactococcus. The core genera in the textile dyeing and fine chemical industrial wastewater treatment systems were Nitrospira, Thauera and Thiobacillus.

This study developed a high-strength molded fiber material (HMFM) using pulp fibers, which could be a good substitute for plastic and solid wood materials. The surface composition, microstructure and thermal properties of HMFM were investigated by XPS, SEM and DSC, respectively. The SEM observations showed that the obvious adhesive substances and agglomeration appeared among fibers, and the inter-fiber contact area and binding tightness increased after the light-delignification. The XPS examination showed that the oxygen-rich composition on the outer surface of HMFM were reduced, and the outer surface coverage of lignin increased from 70.05% to 90.15% after the light-delignification. The DSC observation showed that the thermal stability of HMFM decreased, the temperature for the maximum rate of mass loss decreased from 370 °C to 345.6 °C, and the enthalpy value required for decomposition was reduced from 110.8 J/g to 68.0 J/g after the light-delignification. The mechanical and hydrophobic properties of HMFM were obviously improved after the light-delignification. When the content of lignin decreased from 24.9% to 11.45%, the density of HMFM increased by 6.0%, the tensile strength increased by 22.0%, the bending strength increased by 23.9%, and the water contact angle increased from 64.3°–72.7° to 80.8°–84.3°.

To better understand the relationship between the environmental variables and microbial communities of activated sludge, we took winter samples from different biological treatment units (anaerobic, oxic, etc) from the WWTP’s of a number of Chinese cities. Differences in influent organic components and activated sludge microbial communities were identified by gas chromatography-mass spectrometry and high-throughput sequencing technology, respectively. Liquid nitrogen grinding pretreatment of samples was found to aid in the obtaining of a more bio-diversified sample. Influent type and dissolved oxygen concentration influenced the activated sludge microbial community structure. Nitrospira, Caldilineaceae and Anaerolineaceae were highly related to domestic wastewater treatment systems, whereas Thauera was the most abundant putative refractory aromatic hydrocarbon decomposer found in industrial wastewater treatment systems. Within the influent composition, we speculate that Thauera, Macellibacteroides and Desulfomicrobium are the key functional genera of the anaerobic environment of the textile dyeing industry wastewater treatment systems, whilst Thauera and Thiobacillus are key functional microbes in fine chemical wastewater treatment systems.

Competition of volatile fatty acids between anoxic denitrification and anaerobic phosphorus release is prominent. Therefore, low concentration wastewater has restricted effects on nitrogen and phosphorus removal. The purpose of this study is to treat dormitory sewage with a biochemical oxygen demand (BOD) ranging from 50 to 150 mg/L using dewatered alum sludge-based sequencing batch constructed wetland system. Vegetation in the wetland system was chosen to be Phragmites australis. Three parallel cases were carried out to assess impacts due to different hydraulic retention time (HRT) and artificial aeration. The results showed that this system is effective in removing total nitrogen (TN), ammonia nitrogen (NH3-N) and total phosphorus (TP) under different HRT. However, nitrous oxide (N2O) emission poses to be the greatest challenge in the high HRT cases. Artificial aeration could reduce N2O emission but is associated with high operational cost. Results indicate that dewatered alum sludge-based sequencing batch constructed wetland system is a promising bio-measure in the treatment of low concentration wastewater.

Efficient, fast and new micro-analytical methods for characterization of ultrastructures of fungal spores with electron microscopy are very much required and essential. SEM analysis of biological materials, especially fungi, requires optimal preparation of the specimen and often requires the usage of dried samples which demands a challenging sample preparation. In the present investigation, we described a fast and improved method for the preparation of fungal specimen for scanning electron microscopy (SEM). The fungus, Curvularia lunata was grown on the surface of sterile Whatman No.1 filter paper which was overlaid on Potato Dextrose Agar (PDA) medium, gold coated immediately after removal from the growth medium and subjected to imaging. Generally, SEM imaging is done with samples that were fixed with chemical fixatives, dehydrated and gold coated specimens, but here we describe an easy and more efficient sample preparation for SEM which enabled enhanced image quality and precision visualization of fungal cells, especially the spores. The developed method has enabled the analysis of even the robust samples like fungal spores that to eliminating special temperature requirement. The ultimate goal was to develop an improved protocol/method applied to analysis of fungal spores with greater coverage about fungal specimen preparation. This method permits the use of rapid sample preparation and will allow us to imaging of individual spore or conidia structures in the context of fungal cell architecture which clarifies our understanding in fungal taxonomy/biology.

A conventional anaerobic baffled reactors (ABRs) treating high strength sweet potato starch wastewater at ambient temperatures resulted in acidification and bad performances. After modification, the acidification was remitted and COD removal efficiencies reached 92.73% at high temperatures and were maintained at 71.19% at low temperatures. Moreover, as much as 1.014 ± 0.056 L CH4/L/d were collected at Stage III. The q-PCR results revealed that the largest methanogen populations emerged at Stage III as well, which was 5.29 × 108 mcrA copies per milliliter sludge. A comparable shift in the archaeal community structure at different stages and acetoclastic methanogens Methanosaeta predominated the archaeal community in every compartment in Stages I (63.73%) and II (48.63%). Finally, the net energy gains analysis at mesophilic, thermophilic, and ambient temperature revealed that modified ABR at ambient temperature was not only economical but also profitable and could generated 3.68 KJ energy per gram COD removed.

Few studies have addressed how to blend wastes for anaerobic co-digestion. This study investigated the effects of waste sources on anaerobic co-digestion (AcoD) performance, by varying the quality of food wastes (FWs) from six sources in Xi’an region, China that were individually co-digested with pre-treated corn straw and cattle manure. These effects were analysed in terms of their volatile solid (VS) ratios, C/N ratios, and the chemical composition of the FWs. The results indicated that the VS ratios were not suitable as a common mixture method because the VS ratios at which the best methane potentials occurred differed significantly among the six FW groups. The C/N ratios within a 17–24 range resulted in better methane potentials when the FWs were co-digested with other wastes. Synergistic effects were found among the carbohydrates, proteins, and lipids of the FWs; however, the optimum ratios of these components could not be determined. Thus, the C/N ratio is recommended as a mixture method when co-digesting FWs with other organic wastes in selected region.

In this work, roll-graphene oxide (Ro-GO), polyaniline (PANI) nano/microparticles, and PbS nanoparticles were prepared by modified Hammer, oxidative polymerization, and chemical bath deposition methods, respectively. These nano/microstructures were characterized, optimized, and designed to form PbS/Ro-GO/PANI nano/microcomposite. Also, the ratios of PbS and Ro-GO were optimized, and the optimized composition of the used composite was 0.4 g PANI, 0.125 g Ro-GO, and 0.075 g PbS. The band gap values for PANI, PbS, Ro-GO, and PbS/Ro-GO/PANI rocomposite were 3, 1.13, 2.86, (1.16, 2) eV, respectively. Two photoelectrode assemblies, Au/PbS/Ro-GO/PANI and PbS/Ro-GO/PANI/ITO/glass were used for the photoelectrochemical (PEC) hydrogen generation. In the first assembly 45 nm- Au layer was sputtered on the surface of a disk of PbS/Ro-GO/PANI composite. For the second assembly, a disk of PbS/Ro-GO/PANI composite was glued on ITO glass using Ag-THF paste. The lifetime efficiency values were 64.2 and 43.4% for the first and second electrode for 2 h, respectively. Finally, the incident photon-to-current conversion efficiency (IPCE) and photon-to-current efficiency (ABPE) were calculated under monochromatic illumination conditions. The optimum IPCE efficiency at 390 nm was 9.4% and 16.17%, whereas ABPE % efficiency was 1.01% and 1.75% for Au/PbS/Ro-GO/PANI and PbS/Ro-GO/PANI/ITO/glass, respectively.