Search

Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

Point-of-care testing (POCT) for uropathogen detection and chemical screening has great benefits for the diagnosis of urinary tract infections (UTIs). The goal of this study was to develop a portable and inexpensive paper-based analytical device (PAD) for cultivating bacteria in situ and rapidly testing for nitrite on the same device. The PAD was fabricated using a wax printing technique to create a pattern on Whatman No. 1 filter paper, which was then combined with a cotton sheet to support bacterial growth. Nitrite detection was based on the principle of the Griess reaction, and a linear detection range of 0–1.6 mg/dL (R2 = 0.989) was obtained. Scanning electron microscopy (SEM) analysis demonstrated that the bacteria were able to grow and formed a cluster on the cellulose fibres within 2 hours. The enzyme β-glucuronidase, which is specifically produced by Escherichia coli, was able to convert the pre-immobilized 5-bromo-4-chloro-3-indolyl-β-D-glucuronide sodium salt (X-GlcA), a colourless substrate, generating a blue colour. Under optimum conditions, the proposed device allowed bacterial concentrations in the range of 104–107 colony forming units (CFU)/mL to be quantified within 6 hours. Moreover, the use of this device enables the identification of E. coli pathogens with selectivity in real urine samples. In conclusion, the PAD developed in this study for UTI screening provides a rapid, cost-effective diagnostic method for use in remote areas.

The amount of Paper Board Mill Effluent Treatment Plant Sludge (PBM-ETPS) dumped from paper mills are huge and its conversion into hydrochar for the purpose of energy has broad prospects. This study investigated the optimum conditions for the production of PBM-ETPS derived hydrochar (PBM-ETPSH) through Reponse Surface Methodology (RSM) for more surface area and pore volume with minimal hydrogen to carbon (H/C) and oxygen to carbon (O/C) ratios. The PBM-ETPSH had higher heating value (HHV) of 18.39 MJ kg−1 with fixed carbon percentage of 15.6. Our results showed a reduction in H/C (35.05%) and O/C (43.7%) ratios confirming the coalification of optimized PBM-ETPSH. Thermogravimetric investigations of blending PBM-ETPSH with coal in 1:1 ratio increased its HHV to 22.25 MJ kg−1 making it suitable as an energy alternative for paper mills.

As a two-dimensional material, graphene has attracted increasing attention as heat dissipation material owing to its excellent thermal transport property. In this work, we fabricated sisal nanocrystalline cellulose/functionalized graphene papers (NPGs) with high thermal conductivity by vacuum-assisted self-assembly method. The papers exhibit in-plane thermal conductivity as high as 21.05 W m−1 K−1 with a thermal conductivity enhancement of 403% from the pure cellulose paper. The good thermal transport properties of NPGs are attributed to the strong hydrogen-bonding interaction between nanocrystalline cellulose and functionalized graphene and the well alignment structure of NPGs.

Microfluidic paper-based analytical devices (microPADs) are emerging as cost-effective and portable platforms for point-of-care assays. A fundamental limitation of microPAD fabrication is the imprecise nature of most methods for patterning paper. The present work demonstrates that paper patterned via wax printing can be miniaturized by treating it with periodate to produce higher-resolution, high-fidelity microPADs. The optimal miniaturization parameters were determined by immersing microPADs in various concentrations of aqueous sodium periodate (NaIO4) for varying lengths of time. This treatment miniaturized microPADs by up to 80% in surface area, depending on the concentration of periodate and length of the reaction time. By immersing microPADs in 0.5-M NaIO4 for 48 hours, devices were miniaturized by 78% in surface area, and this treatment allowed for the fabrication of functional channels with widths as small as 301 µm and hydrophobic barriers with widths as small as 387 µm. The miniaturized devices were shown to be compatible with redox-based colorimetric assays and enzymatic reactions. This miniaturization technique provides a new option for fabricating sub-millimeter-sized features in paper-based fluidic devices without requiring specialized equipment and could enable new capabilities and applications for microPADs.

This work presents a cost-effective, label-free in point-of-care (POC) biosensor for the sensitive detection of 8-hydroxy-2′-deoxyguanosine (8-OHdG), the most abundant oxidative product of DNA, that may allow a premature assessment of cancer disease, thereby improving diagnosis, prognostics and survival rates. The device targets the direct detection of 8-OHdG by using for the first time a carbon-ink 3-electrode on a paper substrate coupled to Differential Pulse Voltammetry readings. This design was optimized by adding nanostructured carbon materials to the ink and the conducting polymer PEDOT, enhancing the electrocatalytic properties of the sensor towards 8-OHdG detection. Meanwhile, the ability of this oxidative stress biomarker to undertake an oxidation reaction enabled the development of the sensing electrochemical device without the need of chemical probes and long incubation periods. This paper-modified sensor presented high electrochemical performance on the oxidation of 8-OHdG with a wide linear range (50–1000 ng/ml) and a low detection limit (14.4 ng/ml). Thus, our results showed the development of a direct and facile sensor with good reproducibility, stability, sensitivity and more importantly, selectivity. The proposed carbon-based electrochemical sensor is a potential candidate to be miniaturized to small portable size, which make it applicable for in-situ 8-OHdG sensing in real biological samples.

Paper-based microfluidic devices have many applications in biomedical and environmental analysis. However, the process of prototyping device designs can be tedious, error-prone, and time-consuming. Here, we present a cross-platform, open-source software tool—AutoPAD—developed to quickly create and modify device designs and provide a free alternative to commercial design software. The capabilities that we designed to be inherent to AutoPAD (e.g., automatic zone alignment and design refactoring) highlight its potential use in nearly any paper-based microfluidic device application and for creating nearly any desired design, which we demonstrate through the recreation of numerous device designs from the literature.

For the first time, a paper-based fluorescence resonance energy transfer (FRET) determination with cyclic AMP (cAMP)-specific phosphodiesterase 4B (PDE4B) inhibitory assay using an inkjet-printing technique is proposed. Non-fabricated parchment paper is found to constitute a unique substrate to measure fluorescent energy transfer, due to its insignificant self-absorption, and enables efficient sample interaction. Here, we report the responsive FRET signals generated on paper, upon sequentially printing reaction components on parchment paper using a conventional inkjet printer equipped with four cartridges. After printing, the energy emitted by Eu chelate was transferred by FRET to ULight molecule on paper, detected at 665 nm. In the absence of free cAMP, a maximum FRET signal was achieved on paper, while a decrease in FRET signals was recorded when free cAMP produced by PDE4B inhibitors compete with Eu-cAMP, binding with ULight-mAb. The IM50 value was determined as 2.46 × 10−13 mole for roliparm and 1.86 × 10−13 mole for roflumilast, to effectively inhibit PDE4B activity. Inkjet printing-based FRET signal determination utilizes components that are less than the femtomole range, which was four-orders less than the standard assay method. The methodology reported here constitutes an innovative approach towards the determination of FRET signals generated on paper.

Peaches are known for their palatable flavor and abundant nutrients. However, peaches are perishable, and the existing preservation techniques for peaches are still immature. To further extend the shelf life and prevent nutrient loss of perishable peaches under ambient temperature in summer (approximately 25–32 °C), we conducted experiments wrapping peaches (Prunus persica cv ‘Baihua’) in single- and composite-treated vegetal fibrous papers that contained calcium carbonate, phytic acid, Na-alginate and vitamin C. The pathogenic fungi that primarily caused peach decay during storage belonged to the genera of Penicillium, Botrytis, Aspergillus, Alternaria, and Rhizopus. After analyzing quality attributes, including weight loss, firmness, soluble sugar content, respiration rate, relative electric conductivity, malonaldehyde content, peroxidase activity and the decay index, we proved that vitamin C within the preservative paper greatly contributes to peach preservation. Combined with phytic acid and Na-alginate, the composite vitamin C preservative papers played significant roles in delaying fruit senescence, and 0.4% (w/v) vitamin C preservative paper with 1% Na-alginate could maintain quality and extend shelf life with the best effect. This preservation technique significantly postponed the respiration peak by 2–3 days and is a significant contribution to contemporary commercial production.

3D printed and paper-based microfluidics are promising formats for applications that require portable miniaturized fluid handling such as point-of-care testing. These two formats deployed in isolation, however, have inherent limitations that hamper their capabilities and versatility. Here, we present the convergence of 3D printed and paper formats into hybrid devices that overcome many of these limitations, while capitalizing on their respective strengths. Hybrid channels were fabricated with no specialized equipment except a commercial 3D printer. Finger-operated reservoirs and valves capable of fully-reversible dispensation and actuation were designed for intuitive operation without equipment or training. Components were then integrated into a versatile multicomponent device capable of dynamic fluid pathing. These results are an early demonstration of how 3D printed and paper microfluidics can be hybridized into versatile lab-on-chip devices.

Triboelectric nanogenerators (TENGs) offer an emerging market of self-sufficient power sources, converting the mechanical energy of the environment to electricity. Recently reported high power densities for the TENGs provide new applications opportunities, such as self-powered sensors. Here in this research, a flexible graphene oxide (GO) paper was fabricated through a straightforward method and utilized as the electrode of TENGs. Outstanding power density as high as 1.3 W.m−2, an open-circuit voltage up to 870 V, and a current density of 1.4 µA.cm−2 has been extracted in vertical contact-separation mode. The all-flexible TENG has been employed as a self-powered humidity sensor to investigate the effect of raising humidity on the output voltage and current by applying mechanical agitation in two forms of using a tapping device and finger tapping. Due to the presence of superficial functional groups on the GO paper, water molecules are inclined to be adsorbed, resulting in a considerable reduction in both generated voltage (from 144 V to 14 V) and current (from 23 µA to 3.7 µA) within the range of relative humidity of 20% to 99%. These results provide a promising applicability of the first suggested sensitive self-powered GO TENG humidity sensor in portable/wearable electronics.

In offset printing process, poor mechanical properties and printability of paper substrate usually result in printing problems, low quality of print and waste of paper materials. Therefore, many researches focus on the quality improvement of paper substrates using suitable additives. In this work, N-methylated chitosan, including N, N-dimethyl chitosan (DMC) and N, N, N-trimethyl chitosan (TMC), were prepared and employed as coating agents to ameliorate the mechanical properties and printability of paper sheets. Analysis results showed that the mechanical strength of coated papers with DMC and TMC were largely improved, because the fibers with negative charges were prone to form electrostatic bonding with the positively charged N-methylated chitosan, thus enhancing paper strength. Particularly, compared with chitosan and DMC, the TMC-coated paper exhibited better mechanical properties, printability and surface properties due to the high cationic charge density of TMC. Therefore, surface coating with TMC is of great benefit to decrease the printing problem of paper sheets and enhance the operation speed in offset printing. This work provides a valuable reference for the amelioration of the printability and physical properties of high-quality paper products for many promising applications.

Spatially uniform reconstitution of dried reagents is critical to the function of paper microfluidic devices. Advancing fluid fronts in paper microfluidic devices drive (convect) and concentrate rehydrated reagents to the edges, causing steep chemical gradients and imperfect mixing. This largely unsolved problem in paper microfluidics is exacerbated by increasing device dimensions. In this article, we demonstrate that mixing of dried reagents with a rehydrating fluid in paper microfluidics may be significantly enhanced by stacking paper layers having different wicking rates. Compared to single-layer paper membranes, stacking reduced the “non-reactive area”, i.e. area in which the reconstituted reagents did not interact with the rehydrating fluid, by as much as 97% in large (8 cm × 2 cm) paper membranes. A paper stack was designed to collect ~0.9 ml liquid sample and uniformly mix it with dried reagents. Applications of this technology are demonstrated in two areas: (i) collection and dry storage of sputum samples for tuberculosis testing, and (ii) salivary glucose detection using an enzymatic assay and colorimetric readout. Maximizing the interaction of liquids with dried reagents is central to enhancing the performance of all paper microfluidic devices; this technique is therefore likely to find important applications in paper microfluidics.

A novel strategy for the direct analysis of non-conjugated steroids in water using paper spray mass spectrometry (PS-MS) has been developed. PS-MS was used in the identification and quantification of non-conjugated (free) steroids in fish tank water samples. Data shown herein indicates that individual amounts of free steroids can be detected in aqua as low as; 0.17 ng/µL, 0.039 ng/µL, 0.43 ng/µL, 0.0076 ng/µL for aldosterone, corticosterone, cortisol, and β-estrone, respectively, and with an average relative standard deviation of ca. in aqua.

Microfluidic paper-based analytical devices (µPADs) have provided a breakthrough in portable and low-cost point-of-care diagnostics. Despite their significant scope, the complexity of fabrication and reliance on expensive and sophisticated tools, have limited their outreach and possibility of commercialization. Herein, we report for the first time, a facile method to fabricate µPADs using a commonly available laser printer which drastically reduces the cost and complexity of fabrication. Toner ink is used to pattern the µPADs by printing, without modifying any factory configuration of the laser printer. Hydrophobic barriers are created by heating the patterned paper which melts the toner ink, facilitating its wicking into the cross-section of the substrate. Further, we demonstrate the utilization of the fabricated device by performing two assays. The proposed technique provides a versatile platform for rapid prototyping of µPADs with significant prospect in both developed and resource constrained region.

In this paper we report a cheap, paper electronics based solid state gas sensor to detect NH3 gas selectively with a detection capability of better than 1 ppm. The sensor uses perovskite halide CH3NH3PbI3 (MAPI) as the active sensor material grown on a paper. This paper based sensor works at room temperature. The current through the paper sensor increases by one order on exposure to only 10 ppm NH3 gas. The calibrated sensitivity is ~55% for 1 ppm of NH3 gas in Nitrogen or Air. The current noise limited resolution estimated to be ~10 ppb. This work establishes perovskite halide as a new solid state gas sensing material that can reach sub ppm sensitivity using simple paper electronics. Use of paper and also solution method used to grow the active material makes the sensor cost effective and easy to manufacture. This type of disposable high sensitive paper sensor can be used for detection of NH3 as a marker in exhaled breathes for non-invasive diagnosis. The sensor formed on the paper, since it supports unheated operation, needs less than few nanowatt power for its operation.

The recent Zika virus (ZIKV) outbreak has prompted the need for field-ready diagnostics that are rapid, easy-to-use, handheld, and disposable while providing extreme sensitivity and specificity. To meet this demand, we developed a wax-printed paper microfluidic chip utilizing reverse transcription loop-mediated isothermal amplification (RT-LAMP). The developed simple and sensitive ZIKV assay was demonstrated using undiluted tap water, human urine, and diluted (10%) human blood plasma. Paper type, pore size, and channel dimension of various paper microfluidic chips were investigated and optimized to ensure proper filtration of direct-use biological samples (tap water, urine, and plasma) during capillary action-driven flow. Once ZIKV RNA has flowed and reached to a detection area of the paper microfluidic chip, it was excised for the addition of an RT-LAMP mixture with a pH indicator, then placed on a hot plate at 68 °C. Visible color changes from successful amplification were observed in 15 minutes and quantified by smartphone imaging. The limit of detection was as low as 1 copy/μL. The developed platform can also be used for identifying other flaviviruses, such as Chikungunya virus (CHIKV) and Dengue virus (DENV), and potentially other quickly transmitted virus pathogens, towards field-based diagnostics.

When a fire strikes libraries or archives, physical deterioration of the paper is so severe that its chemical properties are often regarded as less important. However, knowledge of the chemical changes of the papers upon nearly burning is necessary to design a subsequent conservation treatment. In the present study, we have examined a rag paper object, which partially survived a fire, and analysed its chemical properties by various methods. The polymeric state of cellulose, as well as its low-molar mass degradation products, were assessed. Comparison to an identical, unharmed duplicate provided a more profound understanding of the changes caused by the fire. Light scattering analysis revealed conformational changes of the cellulose molecule after high-temperature impact, and a chemical cross-linking was observed. In our study, we found the integrity of cellulose to depend on the temperature profile induced by the fire. The low thermal conductivity of cellulose protects the material even in close proximity to the burned edges.

Graphene oxide (GO) has shown a high potential to adsorb and store water molecules due to the oxygen-containing functional groups on its hydrophilic surface. In this study, we characterized the water absorbing properties of graphene oxide in the form of papers. We fabricated three kinds of graphene oxide papers, two with rich oxygen functional groups and one with partial chemical reduction, to vary the oxygen/carbon ratio and found that the paper with high oxygen content has higher moisture adsorption capability. For the GO paper with reduction, the overall moisture absorbance was reduced. However, the absorbance at high humidity was significantly improved due to direct formation of multilayer water vapor in the system, which derived from the weak interaction between the adsorbent and the adsorbate. To demonstrate one application of GO papers as a desiccant, we tested grape fruits with and without GO paper. The fruits with a GO paper exhibited longer-term preservation with delayed mold gathering because of desiccation effect from the paper. Our results suggest that GO will find numerous practical applications as a desiccant and is a promising material for moisture desiccation and food preservation.

There has been an increasing interest in recent years in isolating cellulose nanofibers from unbleached cellulose pulps for economic, environmental, and functional reasons. In the current work, cellulose nanofibers isolated from high-lignin unbleached neutral sulfite pulp were compared to those isolated from bleached rice straw pulp in making thin-film ultrafiltration membranes by vacuum filtration on hardened filter paper. The prepared membranes were characterized in terms of their microscopic structure, hydrophilicity, pure water flux, protein fouling, and ability to remove lime nanoparticles and purify papermaking wastewater effluent. Using cellulose nanofibers isolated from unbleached pulp facilitated the formation of a thin-film membrane (with a shorter filtration time for thin-film formation) and resulted in higher water flux than that obtained using nanofibers isolated from bleached fibers, without sacrificing its ability to remove the different pollutants.

Due to the high electric conductivity and large surface area of nanographites, such as graphene and graphite nanoplatlets, these materials have gained a large interest for use in energy storage devices. However, due to the thin flake geometry, the viscosity of aqueous suspensions containing these materials is high even at low solids contents. This together with the use of high viscosity bio-based binders makes it challenging to coat in a roll-to-roll process with sufficient coating thickness. Electrode materials for commercial energy storage devices are often suspended by organic solvents at high solids contents and coated onto metal foils used as current-collectors. Another interesting approach is to coat the electrode onto the separator, to enable large-scale production of flat cell stacks. Here, we demonstrate an alternative, water-based approach that utilize slot-die coating to coat aqueous nanographite suspension with nanocellulose binder onto the paper separator, and onto the current collector as reference, in aqueous metal-free supercapacitors. The results show that the difference in device equivalent series resistance (ESR) due to interfacial resistance between electrode and current collector was much lower than expected and thus similar or lower compared to other studies with a aqueous supercapacitors. This indicates that electrode coated paper separator substrates could be a promising approach and a possible route for manufacturing of low-cost, environmentally friendly and metal-free energy storage devices.

Proper drying of hands after washing is an integral part of hand hygiene. An experimental study on 30 subjects using multiple comparisons of six hand drying methods including 1) drying on own clothes, 2) drying with one paper towel, 3) drying with two paper towels, 4) drying with a warm air dryer while holding hands stationary for 20 s, 5) drying with a warm air dryer while hand rubbing for 20 s, and 6) drying with a jet air dryer until complete dryness was achieved. It aimed to determine the effectiveness of different hand drying methods for removing bacteria from washed hands, so as to identify the optimum method using minimum resources. Our study demonstrated that the use of jet air dryers is the best method to eliminate bacteria on hands, whereas drying hands on one’s own clothes is the least effective. Drying hands in a stationary position could remove more bacteria than rubbing hands when using a warm air dryer for 20 s, which mimics people’s usual hand-drying practice. No significant difference in bacteria reduction was detected between the use of one or two paper towels for hand drying; therefore, using fewer resources is recommended to maintain environmental sustainability.

This work presents an alternative method for fabricating Li-ion electrodes in which the use of aluminum/copper current collectors and expensive binders is avoided. Low-cost natural cellulose fibers with a 2-mm length are employed as binder and support for the electrode. The objective of this method is to eliminate the use of heavy and inactive current collector foils as substrates and to replace conventional costly binders with cellulose fibers. Moreover, no harmful solvents, such as N-methylpyrrolidone, are employed for film fabrication. Water-soluble carbons are also utilized to reduce the preparation time and to achieve a better repartition of carbon in the electrode, thus improving the electrochemical performance. Flexible and resistant LiFePO4 (LFP), Li4Ti5O12 (LTO), organic 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA), and graphite electrodes are obtained with active mass loadings similar to those obtained by the current casting method. The initial discharge capacity of approximately 130 mAh·g−1 at 2 C is obtained for an LFP/LTO paper battery with an approximately 91.6% capacity retention after 1000 cycles. An all-organic prelithiated PTCDA/graphite cell without a transition metal is prepared and electrochemically tested. It is one of the first self-standing batteries that is composed of organic redox active molecules and biodegradable components reported in literature.

The prevention of decrease of quality caused by microbial activity in footwear materials entails the use of biocides. However, these substances may pose a hazard to humans and to the natural environment. The paper presents the results of antimicrobial effect investigation for cowhide leather treated with oregano oil. In these studies oil was applied by spraying onto the finished leather surface and examined to determine its antimicrobial activity by using the Agar Diffusion Plate Test. These results were compared with those where a cowhide leather was treated with oil at the stage of fatliquoring. In addition, the oregano oil toxicity level was assessed and compared with biocides used in the tanning industry. Introducing oregano oil into the leather at the stage of fatliquoring provides a better antimicrobial effect than by spraying, however hygienic finishing of leather can be obtained by introducing oil into the raw material by these both methods. The oregano oil is characterised by the lowest number of hazards and toxicity as compared with commercial biocides. The use of essential oils as natural biocides in the tanning industry seems to be especially important and suitable solution considering the harmful effects of synthetic biocides to humans and the environment.

Polyphenols based bioactive compounds from vegetables and fruits are known for impressive antioxidant activity. Ingestion of these antioxidants may promote human health against cardiovascular diseases and cancer. Mango is a popular tropical fruit with special taste, high nutritional value and health-enhancing metabolites. The aim was to investigate the diversity of phytochemicals between two mango cultivars of china at three stages of fruit maturity. We used ESI-QTRAP-MS/MS approach to characterize comprehensively the metabolome of two mango cultivars named Hongguifei (HGF) and Tainong (TN). HPLC was used to quantify selected catechin based phenolic compounds. Moreover, real-time qPCR was used to study the expression profiles of two key genes (ANR and LAR) involved in proanthocyanidin biosynthesis from catechins and derivatives. A total of 651 metabolites were identified, which include at least 257 phenolic compounds. Higher number of metabolites were differentially modulated in peel as compared to pulp. Overall, the relative quantities of amino acids, carbohydrates, organic acids, and other metabolites were increased in the pulp of TN cultivar. While the contents of phenolic compounds were relatively higher in HGF cultivar. Moreover, HPLC based quantification of catechin and derivatives exhibited cultivar specific variations. The ANR and LAR genes exhibited an opposite expression profile in both cultivars. Current study is the first report of numerous metabolites including catechin-based derivatives in mango fruit. These findings open novel possibilities for the use of mango as a source of bioactive compounds.

Made available in DSpace on 2021-06-25T10:15:02Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-12-01 The adoption of dicamba-tolerant soybean varieties has increased the concern and demand for new drift and volatility reduction technologies. Potential spray nozzles and adjuvants should be studied to determine its effects on drift and volatility of dicamba tank-mixtures. The objective of this study was to evaluate physicochemical characteristics of spray solutions containing dicamba; to analyze droplet size effect with air induction nozzles; and to assess dicamba volatilization on soybean plants with a proposed methodology. Treatments included dicamba only and mixtures with herbicides and adjuvants. Dicamba mixed with lecithin + methyl soybean oil + ethoxylated alcohol adjuvant had the greatest efficacy potential among treatments considering tank-mixture pH, surface tension, contact angle and droplet size. The MUG11003 nozzle produced the coarsest droplet size and was better suited for drift management among nozzle types. The proposed volatilization methodology successfully indicated dicamba volatilization in exposed soybean plants and among the evaluated treatments, it showed greater volatilization for dicamba with glyphosate + lecithin + propionic acid adjuvant. Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus

Fuels and their components accumulate in soil, and many soil organisms are exposed to this pollution. Compared to intensive research on the effect of conventional fuel on soil, very few studies have been conducted on soil ecotoxicity of biofuels. Considering the limited information available, the present study evaluated the changes caused by the presence of biodiesel and diesel fuel in soil. The reaction of higher plants and soil organisms (microbial communities and invertebrates) was analysed. Conventional diesel oil and two types of biodiesel (commercial and laboratory-made) were introduced into the soil. Two levels of contamination were applied—5 and 15% (w/w per dry matter of soil). The plate method was used to enumerate microorganisms from soil contaminated with biodiesel and diesel fuel. Phytotoxicity tests were conducted by a 3-day bioassay based on the seed germination and root growth of higher plant species (Sorghum saccharatum and Sinapis alba). Fourteen-day ecotoxicity tests on earthworm were performed using Eisenia fetida. Based on the results of the conducted tests it was found out that the organisms reacted to the presence of fuels in a diverse manner. As to the microorganisms, both the growth and reduction of their number were noted. The reaction depended on the group of microorganisms, type of fuel and dose of contamination. The lipolytic and amylolytic microorganisms as well as Pseudomonas fluorescens bacteria were particularly sensitive to the presence of fuels, especially biodiesel. Fuels, even at a high dose, stimulated the growth of fungi. Monocotyledonous sugar sorghum plants were more sensitive to the presence of fuels than dicotyledonous white mustard. There was also a significant negative impact of contamination level on plant growth and development. Biodiesel, to a greater extent than conventional fuel, adversely affected the survival and volume of earthworms.

Accumulation of the Municipal Sewage Sludge (MSS) is considered as one of the most harmful renewable ecological and human health problems. MSS is a renewable resource that could be used as a soil organic amendment. This study aims to reduce the Heavy Metals (HMs) from the sludge content and sludge compost. Furthermore, this study is considered the first to assess the mycotoxins content in sludge and sludge compost via a new biological treatment using the fungus Serendipita indica or a mixture of lactic acid bacteria, thus providing safer nutrients for the soil amendment for a longer time and preserving human health. The HMs and mycotoxins were determined. The results exhibited that the biotic remediation of bio-solid waste and sewage sludge compost succeeded; a new bio-treated compost with a very low content of heavy metals and almost mycotoxins-free contents was availed. Also, the results indicated that the Lactobacilli mixture realized the best results in reducing heavy metals contents and mycotoxins. Afterward, S. indica. biotic remediation of bio-solid waste and sewage sludge compost minimized the health risk hazards affecting the human food chain, allowing for the different uses of sludge to be safer for the environment.

Sensor data can be wirelessly transmitted from simple, battery-less tags using Radio Frequency Identification (RFID). RFID sensor tags consist of an antenna, a radio frequency integrated circuit chip (RFIC), and at least one sensor. An ideal tag can communicate over a long distance and be seamlessly integrated onto everyday objects. However, miniaturized antenna designs often have lower performance. Here we demonstrate compact, flexible sensor tags with read range comparable to that of conventional rigid tags. We compare fabrication techniques for flexible antennas and demonstrate that screen and stencil printing are both suitable for fabricating antennas; these different techniques are most useful at different points in the design cycle. We characterize two versions of flexible, screen printed folded dipoles and a meandered monopole operating in the 915 MHz band. Finally, we use these antennas to create passive sensor tags and demonstrate over the air communication of sensor data. These tags could be used to form a network of printed, flexible, passive, interactive sensor tags.

Agricultural wastes, such as wheat bran and swine wastewater, were used for bioremediation of oil-contaminated soil. Two optimised strains that could degrade oil efficiently were selected. The result showed that the best ratio of strain A to strain B was 7:3. Swine wastewater could be a replacement for nitrogen source and process water for bioremediation. Next, the Box-Behnken design was used to optimise the culture medium, and the optimal medium was as follows: microbial dosage of 97 mL/kg, wheat bran of 158 g/kg and swine wastewater of 232 mL/kg. Under the optimal medium, the oil degradation rate reached 68.27 ± 0.71% after 40 d. The urease, catalase, and dehydrogenase activities in oil-contaminated soil all increased, and the microbe quantity increased significantly with manual composting. These investigations might lay a foundation for reducing the pollution of agricultural wastes, exploring a late model for bioremediation of oil-contaminated soil.

Two-stage anaerobic digestion of palm oil mill effluent (POME) is a promising method for converting the waste from the largest agricultural industry in Southeast Asia into a clean and sustainable energy. This study investigates the degradation of acid-rich effluent from the dark fermentation stage for the production of biomethane (BioCH4) in a 30-L continuous stirred-tank reactor (CSTR). The continuous methanogenic process was operated with varied HRTs (10 - 1 day) and OLRs (4.6–40.6 gCOD/L.d−1) under thermophilic conditions. Methanothermobacter sp. was the dominant thermophilic archaea that was responsible for the production rate of 4.3 LCH4/LPOME.d−1 and methane yield of 256.77 LCH4kgCOD at HRT of 2 d, which is the lowest HRT reported in the literature. The process was able to digest 85% and 64% of the initial POME’s COD and TSS, respectively. The formation of methane producing granules (MPG) played a pivotal role in sustaining the efficient and productive anaerobic system. We report herein that the anaerobic digestion was not only beneficial in reducing the contaminants in the liquid effluent, but generating BioCH4 gas with a positive net energy gain of 7.6 kJ/gCOD.

The methods of separation of microalgae has a significant impact in the economic aspects of their cultivation. In this study, pine bark was used as a substrate for immobilization of microalgal biomass cultivated in raw municipal sewage. The experiment was conducted in cylindrical photobioreactors (PBRs) with circulation of wastewater. Biomass was cultivated for 42 days. After that time, abundant growth of the biofilm with microalgae on the surface of pine bark as well as improvement of the quality of treated sewage were observed. The efficiency of removal of nutrients from wastewater was 64–81% for total nitrogen and 97–99% for total phosphorus. Moreover, the concentration of suspended solids in sewage was reduced, which resulted in a decrease in turbidity by more than 90%. Colorimetric analysis and Volatile Matter (VM) content in the substrate showed a decrease in the Higher Heating Value (HHV) and concentration of VM due to the proliferation of biofilm.

The industrial wastewater disposal has been growing attention for environmental protection and resource substitution, current decades. Similarly, the durability enhancement of concrete has increased attention by microbial induced CaCO3 precipitation (MICP) process (biocalcification). However, ecofriendly utilization of industrial wastewater in concrete formation is unstudied so far. The present study was carried out to evaluate the effect of industrial wastewater on the formation of cement mortar, compressive strength and water absorption. The biocement mortar strength (y) increased (y = 0.5295×2 + 1.6019×+251.05; R2 = 0.9825) with increasing percentage of organic wastewater (x) (BM0 – BM100) by MICP, where highest strength (280.75 kgf/cm2) was observed on BM100 (100% wastewater), compared to control (252.05 kgf/cm2). The water absorption (y) of biocement mortar decreases (y = −0.0251×2–0.103× + 15.965; R2 = 0.9594) with increment of wastewater (x) (%) (BM0 – BM100), where a minimum-water-absorption (14.42%) observed on BM100, compared to control (15.89%). SEM micrograph and XRD shows the formation of most-distinctive CaCO3 crystallization (aragonite/calcite) (acicular, brick shape, massive and stacked structure) inside biocement mortar (BM100), which fills the pores within cement mortar to form a denser structure, by microbial organic wastewater. Thus, present findings implied a cost-effective of MICP technology to improve the concrete properties along with the mitigation of industrial wastewater pollution, which goes some way towards solving the problem of industrial wastewater pollution.

Phytoremediation is one of the environmental-friendly and cost-effective systems for the treatment of wastewater, including industrial wastewater such as palm oil mill effluent final discharge (POME FD). However, the effects of the wastewater on the phytoremediator plants, in term of growth performance, lignocellulosic composition, and the presence of nutrients and heavy metals in the plants are not yet well studied. In the present work, we demonstrated that POME FD increased the growth of P. purpureum. The height increment of P. purpureum supplied with POME FD (treatment) was 61.72% as compared to those supplied with rain water (control) which was 14.42%. For lignocellulosic composition, the cellulose percentages were 38.77 ± 0.29% (treatment) and 34.16 ± 1.01% (control), and the difference was significant. These results indicated that POME FD could be a source of plant nutrients, which P. purpureum can absorb for growth. It was also found that the heavy metals (Al, As, Cd, Co, Cr, Ni and Pb) inside the plant were below the standard limit of the World Health Organization (WHO). Since POME FD was shown to have no adverse effects on P. purpureum, further research regarding the potential application of P. purpureum following phytoremediation of POME FD such as biofuel production is warranted to evaluate its potential use to fit into the waste-to-wealth agenda.

Mining is an essential human activity, but results in several environmental impacts, notably the contamination of ground and surface water through the presence of toxic substances such as metals and sulfates in mine drainage. Permeable reactive barriers (PRB) have been applied to remediate this environmental impact, but the high costs associated with the maintenance of this system are still a challenge. The main objective of this study was to evaluate the use of kraft pulp mill alkaline residues, known as dregs and grits, as material for PRB, and to determine their capacity for retaining copper and sulfate. The work was carried out in laboratory adsorption kinetics assays, batch assays and column tests. Tests for elemental characterization, point of zero charge, acid neutralization capacity, total porosity, bulk density and moisture of the dregs and grits were conducted. The results showed high retention of Cu due to a chemical precipitation mechanism, notably for dregs (99%) at 5 min in adsorption kinetics. The grits presented similar results after 180 min for the same assay. Sulfate retention was effective at pH below 5, with an efficiency of 79% and 89% for dregs and grits, respectively. Dregs presented the best results for acid drainage remediation, notably with a solid:liquid (S:L) ratio of 1:10.

Vegetable Market have become major sources of organic waste. Some of such waste when being diverted to landfills not only increase the landfill loading but also contribute to increase greenhouse gas emission. Of the many technologies available in handling such hugely generated waste, composting has proven very effective for decades. Enzyme and non-enzyme mediated aerobic composting of vegetable market complex waste (VMCW) have been investigated. Conventional composting technique though being capable of handling large quantum of waste are found to consume more time. Proven to be disadvantages factor. In the present investigation, the pre-cultured seed inoculums used for vegetable market complex waste, shortened the typical composting period from 45 to 9 days for the first time. Also, rapid size and volume reduction of VMCW was witnessed. The organic degradation of VMCW was observed as 42% (82 ± 2.83% to 40.82 ± 0.61%), with a volume reduction from 0.012m3 to 0.003 m3 within 9 days. An enriched nutrients NPK level of compost bio-fertilizer was recorded as 0.91% w/w, 0.5% w/w and 1.029% w/w respectively. Compost maturity observed through the X-ray diffraction (XRD) analysis of the manure confirmed the conversion of the crystal structure of the compost particle to amorphous form and the mineralization of organic matter during the composting. Thus, the fermented pre-cultured seed inoculums favored an enhanced nutrients level with shortened composting time.

Cannabidiol (CBD) has become a buzzword in many products that have bloomed on the market. The scientific community and some authorities have recently raised concerns on the quality of these products. In particular, the discrepancy between the labelled and the real content of cannabidiol in liquids for e-cigarettes seems to be emerging as a major issue. Furthermore, to-date no studies have been carried out on the chemical stability upon storage of these type of products. The aim of this work was to investigate the accuracy in labelling of thirteen commercially e-liquids containing CBD and the effects of different storage conditions on their quality. The results showed that only 38% of samples were labelled within a ±10% variance from their labels. Stability tests showed a maximum degradation of CBD when samples were stored at 37 °C for 30 days with average values up to 20%. The effect of light was lower but still significant with averages values up to 15% degradation after 30 days. In conclusion, we believe that health authorities should regulate and control this market more stringently to protect customers and their health. Furthermore, our stability tests have shown that if clear indications are provided on the best storage conditions, the quality of these products can be mostly preserved.

Ineffectiveness of the chemicals applied so far for waterlogged wood conservation created the need to develop new more, efficient and reliable agents. As an alternative, a new method with the use of organosilicon compounds differing in chemical composition and molecular weight has been investigated. The results obtained show the potential of organosilicons as consolidants in waterlogged wood conservation able to effectively stabilise wood dimensions upon drying. The best wood stabilisers were low-molecular organosilicons enable to penetrate the cell wall as well as chemicals with functional groups capable of interacting with wood polymers and forming stabilising coatings on the cell wall surface. The best anti-shrink efficiency values were obtained for (3-Mercaptopropyl)trimethoxysilane, (3-Aminopropyl)triethoxysilane, 1,3-Bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane, reaching 98, 91 and 91%, respectively. Most of the applied organosilicons reduced wood hygroscopicity, which limits the risk of further dimensional changes of wood exposed to a variable air moisture content and potentially reduces wood biodegradation. In the light of our studies, the proposed method of waterlogged wood conservation with organosilicons is potentially reversible in the case of siloxanes and amino-silanes as well as retreatable, which complies with the requirements of the conservation ethics.

The enhancement of composting technology to stabilize sludge pretreated by ozonation and ultrasonic was tested for 35 days. Secondary sludge produced by biological process are characterized with endogenous residue and inert solid matter which inhibit fully degrade bacterial cell walls. The composting process was performed with sludge pretreated with ozonatian and ultrasonics and green waste in a ratio of 2:1. The composting characteristics was evaluated for different physico-chemical and microbiological parameters in five different reactors. A high degree of composting quality was achieved with respect to significant reduction in volatile solids (VS) (32%), total organic carbon (TOC) (35.0%), C/N ratio (23.74), total coliform (TC) (168) along with the substantial increase in availability of nutrients like N (1.2%) and P (8.77%). High removal efficiency of TC and Fecal Coliform (FC) were observed in composting results, where simultaneous ultrasonic and ozonation were considered as primary-stabilization process. Therefore, applying integrated ultrasonic/ozonation with composting system for sludge stabilization is potentially useful technology in sustainable land restoration practices to meet standards and produce soil conditioner.

The present work investigates biomass wastes and their ashes for re-use in combination with mineralised CO2 in cement-bound construction products. A range of biomass residues (e.g., wood-derived, nut shells, fibres, and fruit peels) sourced in India, Africa and the UK were ashed and exposed to CO2 gas. These CO2-reactive ashes could mineralise CO2 gas and be used to cement ‘raw’ biomass in solid carbonated monolithic composites. The CO2 sequestered in ashes (125–414 g CO2/kg) and that emitted after incineration (400–500 g CO2/kg) was within the same range (w/w). The CO2-reactive ashes embodied significant amounts of CO2 (147–424 g equivalent CO2/kg ash). Selected ashes were combined with raw biomass and Portland Cement, CEM 1 and exposed to CO2. The use of CEM 1 in the carbonated products was offset by the CO2 mineralised (i.e. samples were ‘carbon negative’, even when 10% w/w CEM 1 was used); furthermore, biomass ashes were a suitable substitute for CEM 1 up to 50% w/w. The approach is conceptually simple, scalable, and can be applicable to a wide range of biomass ashes in a closed ‘emission-capture’ process ‘loop’. An extrapolation of potential for CO2 offset in Europe provides an estimate of CO2 sequestration potential to 2030.

Efficient, fast and new micro-analytical methods for characterization of ultrastructures of fungal spores with electron microscopy are very much required and essential. SEM analysis of biological materials, especially fungi, requires optimal preparation of the specimen and often requires the usage of dried samples which demands a challenging sample preparation. In the present investigation, we described a fast and improved method for the preparation of fungal specimen for scanning electron microscopy (SEM). The fungus, Curvularia lunata was grown on the surface of sterile Whatman No.1 filter paper which was overlaid on Potato Dextrose Agar (PDA) medium, gold coated immediately after removal from the growth medium and subjected to imaging. Generally, SEM imaging is done with samples that were fixed with chemical fixatives, dehydrated and gold coated specimens, but here we describe an easy and more efficient sample preparation for SEM which enabled enhanced image quality and precision visualization of fungal cells, especially the spores. The developed method has enabled the analysis of even the robust samples like fungal spores that to eliminating special temperature requirement. The ultimate goal was to develop an improved protocol/method applied to analysis of fungal spores with greater coverage about fungal specimen preparation. This method permits the use of rapid sample preparation and will allow us to imaging of individual spore or conidia structures in the context of fungal cell architecture which clarifies our understanding in fungal taxonomy/biology.

Reduction of CO2 emissions associated with cement production is challenging in view of the increasing cement demand and the fact that major part of the emissions originates from the main raw material used - limestone - which can be only to extremely low amount substituted. A Carbon Capture and Utilization (CCU) approach based on mineralization of fines derived from concrete appears to be a viable alternative to reduce these emissions. The CO2 sequestration and the reactivity of the obtained carbonated recycled fines is experimentally demonstrated for lab as well as industrial materials for different mineralization conditions. It is shown that all CO2 originally released by limestone calcination during clinker production can be sequestered by the full carbonation of the fines within a short time. Upon full carbonation, gels with pozzolanic properties form in the fines irrespective of the conditions tested. The carbonated fines have specific CO2 savings more than 30% higher than the simple clinker replacement by limestone.

Halving the proportion of the people without sustainable access to safe drinking water and basic sanitation is among the Sustainable Development Goals (SDG). Lack of access to safe drinking water has been associated with the prevalence of waterborne diseases. Due to this reported association, the development of household water treatment devices has been an alternative to improve the quality supply of domestic water. In this study, we aimed to evaluate the performance of a ceramic silver-impregnated pot filter (CSF) system coupled with an adsorption process, composed of silver-impregnated granular activated carbon and zeolite (CSF + GAC-Z), to remove waterborne bacteria Escherichia coli and Salmonella spp. from spiked water. The performance of this system was compared with the conventional CSF system. In this respect, we evaluated six CSF and six CSF + GAC-Z using spiked water with 103 and 102 CFU/mL of E. coli and Salmonella spp. The mean percentage of removals ranged between 98% and 99.98%. The highest bacterial removal efficiency was recorded by the CSF + GAC-Z (99%) and CSF (99.98%) for E. coli and Salmonella spp., respectively, but no significant statistical differences were found between filtration systems. Our findings suggest that the CSF + GAC-Z system was effective in the removal of waterborne bacteria from spiked water.

The acute problem of eutrophication increasing in the environment is due to the increase of industrial wastewater, synthetic nitrogen, urine, and urea. This pollutes groundwater, soil and creates a danger to aquatic life. Therefore, it is advantageous to use these waste materials in the form of urea as fuel to generate power using Microbial Fuel Cell (MFC). In this work, we studied the compost soil MFC(CSMFC) unlike typical MFC with urea from the compost as fuel and graphite as a functional electrode. The electrochemical techniques such as Cyclic Voltammetry, Chronoamperometry are used to characterise CSMFC. It is observed that the CSMFC in which the compost consists of urea concertation of 0.5 g/ml produces maximum power. Moreover, IV measurement is carried out using polarization curves in order to study its sustainability and scalability. Bacterial studies were also playing a significant role in power generation. The sustainability study revealed that urea is consumed in CSMFC to generate power. This study confirmed that urea has a profound effect on the power generation from the CSMFC. Our focus is to get power from the soil processes in future by using waste like urine, industrial wastewater, which contains much amount of urea.

Shake-flask cultures of microorganisms involve flame sterilization during sampling, which produces combustion gas with high CO2 concentrations. The gaseous destination has not been deeply analyzed. Our aim was to investigate the effect of flame sterilization on the headspace of the flask and on the shake-flask culture. In this study, the headspace CO2 concentration was found to increase during flame sterilization ~0.5–2.0% over 5–20 s empirically using the Circulation Direct Monitoring and Sampling System. This CO2 accumulation was confirmed theoretically using Computational Fluid Dynamics; it was 9% topically. To evaluate the influence of CO2 accumulation without interference from other sampling factors, the flask gas phase formed by flame sterilization was reproduced by aseptically supplying 99.8% CO2 into the headspace, without sampling. We developed a unit that can be sampled in situ without interruption of shaking, movement to a clean bench, opening of the culture-plug, and flame sterilization. We observed that the growth behaviour of Escherichia coli, Pelomonas saccharophila, Acetobacter pasteurianus, and Saccharomyces cerevisiae was different depending on the CO2 aeration conditions. These results are expected to contribute to improving microbial cell culture systems.

Simultaneous saccharification and fermentation (SSF) with delayed yeast extract feeding (DYEF) was conducted in a 2-L bioreactor equipped with in-situ recovery using a gas stripping in order to enhance biobutanol production from lignocellulosic biomass of oil palm empty fruit bunch (OPEFB). This study showed that 2.88 g/L of biobutanol has been produced from SSF with a similar yield of 0.23 g/g as compared to separate hydrolysis and fermentation (SHF). An increase of 42% of biobutanol concentration was observed when DYEF was introduced in the SSF at 39 h of fermentation operation. Biobutanol production was further enhanced up to 11% with a total improvement of 72% when in-situ recovery using a gas stripping was implemented to reduce the solvents inhibition in the bioreactor. In overall, DYEF and in-situ recovery were able to enhance biobutanol production in SSF.

The current study analyzed and optimized the concentration of NaOH for alkaline pretreatment of kitchen refuse for biogas production. Also, the benefits of microwave assistance in enhanced biogasification of kitchen refuse were evaluated. The TS, VS and structural changes were compared using standard experimental techniques. Molecular dynamics was investigated for the molecular level changes leading to higher biogasification in NaOHmicrowave combined pretreatment. The methane and biogas yields were calculated to validate the benefits of microwave assistance in efficient biogasification. The NaOH-microwave combined pretreatment showed higher VS production. Microwave treatment degraded and removed lignin more efficiently. Molecular dynamics studies revealed the induction of configurational instability in lignin and cellulose molecules with variable temperatures. The methane and biogas production increased with 6% NaOH concentration, and decreased at higher NaOH concentration till 10%. Microwave assistance declined the required NaOH concentration further to 4%. Thus, as compared to 6% NaOH concentration required for an efficient pretreatment, the kitchen refuse was efficiently pretreated with 4% NaOH concentration when combined with a 30 min duration microwaving. The experimental and computational data provided a detailed analysis proposing an optimized, novel and promising method to pretreat kitchen refuse for efficient and enhanced biogas production.

Recently, historical and conservation studies have attached an increasing importance to investigating the materials used in historic documents. In particular, the identification of the animal species from which parchments are made is of high importance and is currently performed by either genetic or proteomic methods. Here, we introduce an innovative, non-invasive optical method for identifying animal species based on light-parchment interaction. The method relies on conservation of light energy through reflection, transmission and absorption from the sample, as well as on statistical processing of the collected optical data. Measurements are performed from ultraviolet (UV) to near-infrared (NIR) spectral ranges by a standard spectrophotometer and data are processed by Principal Component Analysis (PCA). PCA data from modern parchments, made of sheep, calf and goat skins, are used as a database for PCA analysis of historical parchments. Using only the first two principal components (PCs), the method confirmed visual diagnostics about parchment appearance and aging, and was able to recognise the origin species of historical parchment of among database clusters. Furthermore, taking into account the whole set of PCs, species identification was achieved, with all results matching perfectly their proteomic counterparts used for method assessment. The validated method compares favourably with genetic and proteomic methods used for the same purpose. In addition to animals’ proteomic and genetic signatures, a unique “optical fingerprint” of the parchments’ origin species is revealed here. This new method is non-invasive, straightforward to implement, potentially cheap and accessible to scholars and conservators, with minimal training. In the context of cultural heritage, the method could help solving questions related to parchment production and, more generally, medieval writing production.

The preservation of cultural heritage is one of the major challenges of today’s society. Parchments, a semi-solid matrix of collagen produced from animal skin, are a significant part of the cultural heritage, being used as writing material since ancient times. Due to their animal origin, parchments easily undergo biodeterioration: the most common biological damage is characterized by isolated or coalescent purple spots, that often lead to the detachment of the superficial layer and the consequent loss of written content. Although many parchments with purple spot biodegradative features were studied, no common causative agent had been identified so far. In a previous study a successional model has been proposed, basing on the multidisciplinary analysis of damaged versus undamaged samples from a moderately damaged document. Although no specific sequences were observed, the results pointed to Halobacterium salinarum as the starting actor of the succession. In this study, to further investigate this topic, three dramatically damaged parchments were analysed; belonging to a collection archived as Faldone Patrizi A 19, and dated back XVI-XVII century A.D. With the same multidisciplinary approach, the Next Generation Sequencing (NGS, Illumina platform) revealed DNA sequences belonging to Halobacterium salinarum; the RAMAN spectroscopy identified the pigment within the purple spots as haloarchaeal bacterioruberin and bacteriorhodopsine, and the LTA technique quantified the extremely damaged collagen structures through the entire parchments, due to the biological attack to the parchment frame structures. These results allowed to propose a model of the progressive degradation pattern of the parchment collagen. Overall, these data validate a multi-phase microbial succession model. This demonstration is pivotal to possible new restoration strategies, important for a huge number of ancient documents.

Activated sludge from wastewater treatment plants was seeded into a sequencing batch reactor (SBR) in which synthetic wastewater was used as the influent. The sludge was bulked by decreasing the concentration of dissolved oxygen (DO). By adding a 30 min step of anaerobic stirring after the water inflow, the sludge bulking was rapidly inhibited after 10 running cycles, and the sludge volume index (SVI) decreased from 222 to 74 mL·g−1. The results of high-throughput sequencing showed that the relative abundance of bacteria Thiothrix, bacteria norank_o_Sphingobacteriales and fungi Trichosporon was increased by 6.3, 4.3 and 81.2%, after initial SBR stages, but these bacteria were inhibited by the addition of an anaerobic step, as their relative abundances decreased by 0.7, 0.8 and 14.7%, respectively. The proliferation of Thiothrix, norank_o_Sphingobacteriales and Trichosporon was the primary reason for the observed sludge bulking in the reactor. After the anaerobic step was added, the sludge extracellular polymeric substances (EPS) concentration was increased from 84.4 to 104.0 mg·(gMLSS)−1 (grams of mixed liquor suspended solids). Thus, the addition of an anaerobic step can inhibit the growth of filamentous bacteria, increasing the sludge EPS concentration and promoting the precipitation of activated sludge.