Search

Rapid and accurate bioburden detection has become increasingly necessary for food, health, pharmaceutical and environmental applications. To detect bioburden accurately, and in a highly sensitive manner, we have fabricated a novel microfluidic device with an integrated filter to trap the cells. Bioburden is detected on the filter paper in situ using the redox reaction of fluorescent label resorufin and a portable multichannel fluorometer is used for fluorescence measurement. The microfluidic device was fabricated in a facile, low-cost, and rapid way with microwave-induced thermally assisted bonding. To characterize the bonding quality of the microfluidic cassettes, different tests were performed, and the filter paper material and size were optimized. Primary Bacillus subtilis culture bacterial samples were filtered through the device to validate and investigate the performance parameters. Our results show that a limit of detection (LOD) of 0.037 CFU/mL can be achieved through this microfluidic device whereas the LOD in a normal microfluidic cassette in the fluorometer and the golden standard spectrophotometer are 0.378 and 0.128 CFU/mL respectively. The results depict that three to ten times LOD improvement is possible through this microfluidic cassette and more sensitive detection is possible depending on the volume filtered within a rapid 3 min. This novel microfluidic device along with the fluorometer can be used as a rapid portable tool for highly sensitive, accurate and high-throughput bacterial detection for different applications. [ABSTRACT FROM AUTHOR]

Abstract Paper spray ionization (PSI) mass spectrometry (MS) is an emerging tool for ambient reaction monitoring via microdroplet reaction acceleration. PSI-MS was used to accelerate and monitor the time course of the reaction of dansyl chloride with aniline, in acetonitrile, to produce dansyl aniline. Three distinct PSI arrangements were explored in this study representing alternative approaches for sample loading and interaction; conventional single tip as well as two novel setups, a dual-tip and a co-axial arrangement were designed so as to limit any on-paper interaction between reagents. The effect on product abundance was investigated using these different paper configurations as it relates to the time course and distance of microdroplet travel. It was observed that product yield increases at a given distance and then decreases thereafter for all PSI configurations. The fluorescent property of the product (dansyl aniline) was used to visually inspect the reaction progress on the paper substrate during the spraying process. Amongst the variety of sample loading methods the novel dual-tip arrangement showed an increased product yield and microdroplet density, whilst avoiding any on-paper interaction between the reagents.

There has been growing interest in the development of paper-based biosensors because their simplicity and low cost are attractive for point-of-care diagnosis, especially in low-resource areas. However, only a limited range of paper materials - primarily chromatography papers - have been incorporated into diagnostics thus far. Here, we investigate the performance of different types of paper in order to develop an aptamer- and MoS 2 nanosheet-based sensor relying on fluorescence resonance energy transfer (FRET) to signal the presence of a target protein. An aptamer which binds to a malarial biomarker, Plasmodium lactate dehydrogenase (pLDH), is chosen for this study, as point-of-care diagnostics would be especially advantageous in low-resource areas, such as those where malaria is prevalent. We observe that of all papers tested, a measurable and specific fluorescence recovery can only be produced on the sensor created with printer paper, while no significant fluorescence recovery is generated on sensors made from other types of paper, including chromatography, lens, and filter papers. Therefore, our findings demonstrate the importance of careful material selection for the development of a paper-based diagnostic test, and suggest that commercially-available products such as printer paper may serve as viable materials to develop cost-effective and simple diagnostics.

Abstract Low energy surface coatings have found wide range of applications for generating hydrophobic and superhydrophobic surfaces. Most of the studies have been related to use of a single coating material over a single substrate or using a single technique. The degree of hydrophobicity is highly dependent on fabrication processes as well as materials being coated and as such warrants a high-level study using experimental optimization leading to the evaluation of the parametric behavior of coatings and their application techniques. Also, a single platform or system which can predict the required set of parameters for generating hydrophobic surface of required nature for given substrate is of requirement. This work applies the powerful machine learning algorithms (Levenberg Marquardt using Gauss Newton and Gradient methods) to evaluate the various processes affecting the anti-wetting behavior of coated printable paper substrates with the capability to predict the most optimized method of coating and materials that may lead to a desirable surface contact angle. The major application techniques used for this study pertain to dip coating, spray coating, spin coating and inkjet printing and silane and sol–gel base coating materials.

Abstract Achieving an efficient catalyst in the ATRP system with a simple design, preparation from available materials, and high recyclability is a significant challenging issue. To attain the goal, herein, we used chitosan (CS)-modified cellulose filter paper (FP) as a green support for the synthesis of dip catalyst. The preparation of this catalyst involved surface treatment of the FP strips by CS coating through a dipping method, which increased the affinity of the substrate for adsorbing copper ions in the next step. The Cu@CS-FP catalyst was prepared without the requirement of any ligands. The synthesized dip-catalyst, in the form of the strips, was employed for the first time in the ATRP reaction of methyl methacrylate to assay catalytic activity. Catalytic insertion/ removal (ON/OFF) experiments were carried out during the polymerization. A reasonable control over the molecular weight with high conversion (68%) and polydispersity index of 1.32 under mild reaction conditions were obtained. Significantly, because of the facile separation of the catalyst, the amount of copper that remained in the polymer was very low (2.7 ppm). Also, the recyclability of the catalyst was investigated for five runs. The conversion in the final run was 64% without a loss of catalyst efficiency.

Abstract Cyanide-based blood poisoning can seriously damage fire victims and cause death if not detected quickly. Previous conventional methods require laboratory equipment, which are expensive and increase the duration of the analysis. Here, a simple origami based microfluidic device was introduced for point of need detection of blood cyanide concentration in people involved in fire. The device is made of four layers of paper. Each layer was in the size of 1 × 1 cm folded on each other. In this work, the blood sample was acidified by trichloroacetic acid to separate cyanide from methaemoglobin in the form of HCN gas. The produced gas released into borate buffer to recover free cyanide ions which interacted with the Pt complex ([Pt(p-MeC6H4)2(phen)]) used as a receptor in this study. Optimized conditions were applied to have a suitable interaction causing the color of the receptor to change from yellow to colorless. The color changes were recorded by a smartphone, and the sensor response was calculated by the routine image analysis software. The assay was capable of determining cyanide ions at different concentrations in the range of 1.0 to 100.0 µmol L−1. The detection limit of these determination was equal to 0.4 µmol L−1. The assay responses were not affected by the interfering species. As a practical analysis, the proposed sensor was applied to determine cyanide ions in the blood sample of 20 studied fire survivors and 10 controls with high accuracy.

For shaped charge blasting projects in mining, civil engineering, and similar fields, it is proposed to modify the charge structure by combining slotted tubes and shaped charge liners to obtain a new type of charge structure. This aims to achieve directional rock breaking through the focused action of the shaped charge. The influence of different slotted pipe materials on the directional rock-breaking effect of concentrated energy using a new charge structure is explored through theoretical analysis combined with model test study, high-speed camera, stress–strain gauge, and other equipment. A comparison is made between slotted pipes made of aluminum, kraft paper, and PVC, with the cutting width of 2 mm. Based on the characteristics of the cracks formed after blasting, the new charge structure made of aluminum slotted pipe produces a penetrating crack that is almost consistent with the pre-cracking direction. Based on the corresponding characteristics of successively released blasting energy, the guiding and convergence effect of the new charge structure made of aluminum slotted pipe on the explosion energy is greater than that of the new charge structure made of the other two types of slotted pipe material. According to the strain data measured after blasting, the peak arrival time of the strain peak in the direction of the slotted pipe on one side of the shaped hood is shorter than that in the other two directions, and the peak strain is greater than that in the other two directions while having a better energy gathering effect. Based on the findings, the new charge structure with directional energy concentration has a damage reduction effect. Furthermore, the material of aluminum slotted pipe is found to be better than PVC slotted pipe, whereas the material of PVC slotted pipe is better than kraft paper slotted pipe in achieving directional rock breaking. [ABSTRACT FROM AUTHOR]

Abstract This study introduces an applicable colorimetric sensor array for the detection of pesticides in the vapor phase. The array consisted of six metal nanoparticles spotted on the piece of filter paper. 3D-origami pattern was used for the fabrication of a paper-based sensor to decrease the effect of the nanoparticles leaching after exposure to analytes. Exposure to pesticide aerosols caused changes in the color of the array due to the aggregation of nanoparticles. These changes provided selective responses to thion pesticides such as malathion, parathion, chlorpyrifos, and diazinon. The sensing assay could also differentiate between aliphatic and aromatic thions and discriminate amine-containing compounds from the other studied analytes. These finding results are clearly confirmed by both visual detection and multivariate statistical methods. The proposed sensor was successfully developed for the quantitative measurement of pesticide aerosols at a very low concentration. The limit of detection of this method determined for malathion, parathion, chlorpyrifos and diazinon were 58.0, 103.0, 81.0 and 117.0, respectively. Moreover, the array could be employed to simultaneously analyze four studied pesticides. The statistcal results confirmed that the method has high performance for concurrent detection of thions as a major air pollutant without the interference of other species.

Abstract Graphite pencil stroked electrodes for paper-based Microfluidic devices are gaining immense attention due to their electrochemical properties, cost efficiency, and ease-of-use. However, their widespread use has been hindered by the challenges associated with their manual fabrication such as non-uniformity in graphite deposition, applied pressure, etc. This work presents the design and development of an automated graphite pencil stroking device for graphite electrode fabrication with high efficiency through a compact, inexpensive and automatic process, with reduced fabrication time and human intervention leading to more uniformity. The motion platform of Graphtec plotter was used to create multiple strokes with the help of the proposed device. Such inexpensive graphite electrodes (less than the US $1) have been observed to be porous in nature, acting as diffusion agents. The automated graphite electrodes were used to study the performance of microfluidic paper fuel cells (MPFCs) with formic acid, oxygen, and sulphuric acid acting as fuel, oxidising agent and electrolyte respectively. From this configuration, the maximum current density and power density were measured to be 1,305.5 µA cm−2 and 135.5 µW cm−2, respectively at 0.3 V stable OCP at 100 strokes. Overall, the study enumerates the development of an automated pencil stroke device for fabricating graphite electrodes, which can potentially be harnessed in numerous miniaturized paper based applications.

Abstract Development of paper-based microfluidic devices that perform colorimetric measurements requires quantitative image analysis. Because the design geometries of paper-based microfluidic devices are not standardized, conventional methods for performing batch measurements of regularly spaced areas of signal intensity, such as those for well plates, cannot be used to quantify signal from most of these devices. To streamline the device development process, we have developed an open-source program called ColorScan that can automatically recognize and measure signal-containing zones from images of devices, regardless of output zone geometry or spatial arrangement. This program, which measures color intensity with the same accuracy as standard manual approaches, can rapidly process scanned device images, simultaneously measure identified output zones, and effectively manage measurement results to eliminate requirements for time-consuming and user-dependent image processing procedures.

Invasive species can be particularly disruptive when they intersect with organisms of conservation concern. Stabilizing the declining eastern migratory population of monarch butterflies (Danaus plexippus) is projected to require extensive habitat restoration across multiple land use sectors including metropolitan areas. Numerous conservation programs encourage urban citizens to plant gardens with milkweeds, the obligate larval host plants of the monarch. Here, we show that predation by Polistes dominula, an invasive paper wasp that is particularly abundant in urban settings, can turn such sites into ecological traps for monarch larvae. Polistes dominula was the predominant paper wasp seen foraging in central Kentucky pollinator gardens. In 120 observed encounters with monarch larvae on milkweeds in gardens, most second to fourth instars were killed, whereas most fifth instars escaped by thrashing or dropping. The wasps bit and carried off second instars whole, whereas third and fourth instar kills were first gutted, then processed and carried away piecemeal. Predation on sentinel larvae was much higher in urban gardens than in rural settings. The wasps exploited ornamental butterfly "hibernation boxes" in pollinator gardens as nesting habitat. Polistes dominula is an under-recognized predator that may diminish the urban sector's contributions to monarch habitat restoration. [ABSTRACT FROM AUTHOR]

Abstract Analyzing electrolytes in urine, such as sodium, potassium, calcium, chloride, and nitrite, has significant diagnostic value in detecting various conditions, such as kidney disorder, urinary stone disease, urinary tract infection, and cystic fibrosis. Ideally, by regularly monitoring these ions with the convenience of dipsticks and portable tools, such as cellphones, informed decision making is possible to control the consumption of these ions. Here, we report a paper-based sensor for measuring the concentration of sodium, potassium, calcium, chloride, and nitrite in urine, accurately quantified using a smartphone-enabled platform. By testing the device with both Tris buffer and artificial urine containing a wide range of electrolyte concentrations, we demonstrate that the proposed device can be used for detecting potassium, calcium, chloride, and nitrite within the whole physiological range of concentrations, and for binary quantification of sodium concentration.

We present a simple all-in-one paper-based sensor for E. coli detection using a composite ink made of a fluorogenic DNAzyme probe for bacterial recognition and signal generation, lysozyme that lyses whole bacterial cells, and pullulan/trehalose sugars that stabilize printed bioactive molecules. The paper sensor is capable of producing a fluorescence signal as a readout within 5 minutes upon contacting E. coli, can achieve a limit of detection of 100 cells/mL, in a variety of sample matrixes, without sample enrichment, and remains stable for at least 6 months when stored at ambient temperature. Therefore, this simple paper sensor provides rapid bacterial testing on site, and can be shipped and stored under ambient conditions to benefit users living in resource-limited regions.

Peaches are known for their palatable flavor and abundant nutrients. However, peaches are perishable, and the existing preservation techniques for peaches are still immature. To further extend the shelf life and prevent nutrient loss of perishable peaches under ambient temperature in summer (approximately 25-32 °C), we conducted experiments wrapping peaches (Prunus persica cv 'Baihua') in single- and composite-treated vegetal fibrous papers that contained calcium carbonate, phytic acid, Na-alginate and vitamin C. The pathogenic fungi that primarily caused peach decay during storage belonged to the genera of Penicillium, Botrytis, Aspergillus, Alternaria, and Rhizopus. After analyzing quality attributes, including weight loss, firmness, soluble sugar content, respiration rate, relative electric conductivity, malonaldehyde content, peroxidase activity and the decay index, we proved that vitamin C within the preservative paper greatly contributes to peach preservation. Combined with phytic acid and Na-alginate, the composite vitamin C preservative papers played significant roles in delaying fruit senescence, and 0.4% (w/v) vitamin C preservative paper with 1% Na-alginate could maintain quality and extend shelf life with the best effect. This preservation technique significantly postponed the respiration peak by 2-3 days and is a significant contribution to contemporary commercial production.

The high cost, complexity and reliance on electricity, specialized equipment and supplies associated with conventional diagnostic methods limit the scope and sustainability of newborn screening for sickle cell disease (SCD) in sub-Saharan Africa and other resource-limited areas worldwide. Here we describe the development of a simple, low-cost, rapid, equipment- and electricity-free paper-based test capable of detecting sickle hemoglobin (HbS) in newborn blood samples with a limit of detection of 2% HbS. We validated this newborn paper-based test in a cohort of 159 newborns at an obstetric hospital in Cabinda, Angola. Newborn screening results using the paper-based test were compared to conventional isoelectric focusing (IEF). The test detected the presence of HbS with 81.8% sensitivity and 83.3% specificity, and identified SCD newborns with 100.0% sensitivity and 70.7% specificity. The use of the paper-based test in a two-stage newborn screening process could have excluded about 70% of all newborns from expensive confirmatory testing by IEF, without missing any of the SCD newborns in the studied cohort. This study demonstrates the potential utility of the newborn paper-based test for reducing the overall cost of screening newborns for SCD and thus increasing the practicality of universal newborn SCD screening programs in resource-limited settings.

To achieve integrated resource utilization of graphite tailings to improve their water-holding capacity, river silt and cow dung powder were added to graphite tailings as organic matter improvers. Improver ratios were designed using 4 g cow dung powder and 20, 30, and 50 g river silt. Soil–water characterization tests were performed using a combined tensiometer and filter paper method based on optimum density measurements. Analysis of the influence of river silt dosing on the soil–water characteristic curves of improved graphite tailing specimens was performed with data fitting using the Van Genuchten model. Here, we investigated the effect of river silt dosing on the internal pore structure and water-holding capacity of modified graphite tailing samples and verified the applicability of the model to graphite tailings. Our results demonstrate that the organic matter improver incorporated into graphite tailings can improve the internal structural compactness of graphite tailings, improving the water holding capacity. With an increase in river silt dosage, the saturated water content is larger, and the residual water content increases and then decreases. When river silt dosage is 30 g, the residual water content is the highest at a value of 3.32%. The van Genuchten model was highly accurate for assessing the graphite tailings. With an increase in river silt doping, the internal pore space first decreased and then increased, and the internal structure gradually became compact and loosened. The internal structure was in the optimal state in the experimental study when the dosage of cow dung powder was 4 g and the dosage of river silt was 30 g. The water holding capacity was optimal at this time. The results of this study provide a theoretical foundation for graphite-tailing-based mine reclamation and play a guiding role in exploring the value of the hydraulic characteristic index parameters when applying graphite tailings engineering. [ABSTRACT FROM AUTHOR]

Abstract We present a prototype for conducting rapid, inexpensive and point-of-care-compatible nucleic acid amplification tests (NAATs) for tuberculosis (TB). The fluorescent isothermal paper-and-plastic NAAT (FLIPP-NAAT) uses paper-based loop mediated isothermal amplification (LAMP) for DNA detection. The cost of materials required to build a 12-test-zone device is $0.88 and the cost of reagents per reaction is $0.43. An inexpensive imaging platform enables filter-free fluorescence detection of amplified DNA using a cell-phone camera. FLIPP-NAAT can be operated by an untrained user and only requires a regular laboratory incubator as ancillary equipment. All reagents can be dry-stored in the device, facilitating storage and transportation without cold chains. The device design is modular and the assay demonstrated high specificity to Mycobacterium tuberculosis (Mtb), analytical sensitivity of the order of 10 copies of Mtb gDNA, and tolerance to complex samples. The clinical sensitivity and specificity of sputum-based FLIPP NAAT tests were 100% (zero false negatives) and 68.75% (five false positives), respectively (N = 30), using Xpert MTB/RIF assay as the reference standard. FLIPP-NAAT has the potential to provide affordable and accessible molecular diagnostics for TB in low- and middle-income countries, when used in conjunction with an appropriate sample preparation technique. Although demonstrated for the detection of TB, FLIPP-NAAT is a platform technology for amplification of any nucleic acid sequence.

Polymers are often combined with magnetostrictive materials to enhance their toughness. This study reports a cellulose nanofibril (CNF)-based composite paper containing dispersed CoFe2O4 particles (CNF–CoFe2O4). Besides imparting magnetization and magnetostriction, the incorporation of CoFe2O4 particles decreased the ultimate tensile strength and increased the fracture elongation of the CNF–CoFe2O4 composite paper. CNF was responsible for the tensile properties of CNF–CoFe2O4 composite paper. Consequently, the magnetic and magnetostrictive properties and tensile properties of CNF–CoFe2O4 composite paper can be controlled by changing the mixture ratio of CNF and CoFe2O4 particles. [ABSTRACT FROM AUTHOR]

Metagenomics has revolutionized access to genomic information of microorganisms inhabiting the gut of herbivorous animals, circumventing the need for their isolation and cultivation. Exploring these microorganisms for novel hydrolytic enzymes becomes unattainable without utilizing metagenome sequencing. In this study, we harnessed a suite of bioinformatic analyses to discover a novel cellulase-degrading enzyme from the camel rumen metagenome. Among the protein-coding sequences containing cellulase-encoding domains, we identified and subsequently cloned and purified a promising candidate cellulase enzyme, Celcm05-2, to a state of homogeneity. The enzyme belonged to GH5 subfamily 4 and exhibited robust enzymatic activity under acidic pH conditions. It maintained hydrolytic activity under various environmental conditions, including the presence of metal ions, non-ionic surfactant Triton X-100, organic solvents, and varying temperatures. With an optimal temperature of 40 °C, Celcm05-2 showcased remarkable efficiency when deployed on crystalline cellulose (> 3.6 IU/mL), specifically Avicel, thereby positioning it as an attractive candidate for a myriad of biotechnological applications spanning biofuel production, paper and pulp processing, and textile manufacturing. Efficient biodegradation of waste paper pulp residues and the evidence of biopolishing suggested that Celcm05-2 can be used in the bioprocessing of cellulosic craft fabrics in the textile industry. Our findings suggest that the camel rumen microbiome can be mined for novel cellulase enzymes that can find potential applications across diverse biotechnological processes. [ABSTRACT FROM AUTHOR]

Sensitive, specific, rapid, inexpensive and easy-to-use nucleic acid tests for use at the point-of-need are critical for the emerging field of personalised medicine for which companion diagnostics are essential, as well as for application in low resource settings. Here we report on the development of a point-of-care nucleic acid lateral flow test for the direct detection of isothermally amplified DNA. The recombinase polymerase amplification method is modified slightly to use tailed primers, resulting in an amplicon with a duplex flanked by two single stranded DNA tails. This tailed amplicon facilitates detection via hybridisation to a surface immobilised oligonucleotide capture probe and a gold nanoparticle labelled reporter probe. A detection limit of 1 × 10 -11  M (190 amol), equivalent to 8.67 × 10 5 copies of DNA was achieved, with the entire assay, both amplification and detection, being completed in less than 15 minutes at a constant temperature of 37 °C. The use of the tailed primers obviates the need for hapten labelling and consequent use of capture and reporter antibodies, whilst also avoiding the need for any post-amplification processing for the generation of single stranded DNA, thus presenting an assay that can facilely find application at the point of need.

Enzyme linked immunosorbent assay (ELISA) is one of the most widely used laboratory disease diagnosis methods. However, performing ELISA in low-resource settings is limited by long incubation time, large volumes of precious reagents, and well-equipped laboratories. Herein, we developed a simple, miniaturized paper/PMMA (poly(methyl methacrylate)) hybrid microfluidic microplate for low-cost, high throughput, and point-of-care (POC) infectious disease diagnosis. The novel use of porous paper in flow-through microwells facilitates rapid antibody/antigen immobilization and efficient washing, avoiding complicated surface modifications. The top reagent delivery channels can simply transfer reagents to multiple microwells thus avoiding repeated manual pipetting and costly robots. Results of colorimetric ELISA can be observed within an hour by the naked eye. Quantitative analysis was achieved by calculating the brightness of images scanned by an office scanner. Immunoglobulin G (IgG) and Hepatitis B surface Antigen (HBsAg) were quantitatively analyzed with good reliability in human serum samples. Without using any specialized equipment, the limits of detection of 1.6 ng/mL for IgG and 1.3 ng/mL for HBsAg were achieved, which were comparable to commercial ELISA kits using specialized equipment. We envisage that this simple POC hybrid microplate can have broad applications in various bioassays, especially in resource-limited settings.

This work demonstrates the fabrication of partially mineralized scaffolds fabricated in 3D shapes using paper by folding, and by supporting deposition of calcium phosphate by osteoblasts cultured in these scaffolds. This process generates centimeter-scale free-standing structures composed of paper supporting regions of calcium phosphate deposited by osteoblasts. This work is the first demonstration that paper can be used as a scaffold to induce template-guided mineralization by osteoblasts. Because paper has a porous structure, it allows transport of O2 and nutrients across its entire thickness. Paper supports a uniform distribution of cells upon seeding in hydrogel matrices, and allows growth, remodelling, and proliferation of cells. Scaffolds made of paper make it possible to construct 3D tissue models easily by tuning material properties such as thickness, porosity, and density of chemical functional groups. Paper offers a new approach to study mechanisms of biomineralization, and perhaps ultimately new techniques to guide or accelerate the repair of bone.

In this study, we developed a new type of paper-based analytical device (PAD), the three-dimensional (3D) slip-PAD, to detect infectious human norovirus for global healthcare. The 3D configuration of the papers combined with a slip design provides unique features and versatility that overcome the limitations of fluidic manipulation and sensitivity in point-of-care (POC) tests. The assay can be carried out in a single step based on a moveable slip design, making it suitable for unskilled users. The 3D fluidic network developed by layered construction of wax-patterned papers provides different fluidic paths for the sequential delivery of multiple fluids without the need for peripheral equipment. The release and mixing of enhancement reagents on the device improved the sensitivity and detection limit. The assay results could be visualized by naked eye within 10 min, with subsequent amplification of the signal over time (<60 min). The device showed a broad dynamic range of detection and high sensitivity, with a detection limit of 9.5 × 10(4) copies ml(-1) for human norovirus. These results demonstrate that the 3D slip-PAD is a sensitive diagnostic assay for detecting human norovirus infection that is particularly suitable for POC testing in regions where resources are scarce.

A paper-based upconversion fluorescence resonance energy transfer assay device is proposed for sensitive detection of CEA. The device is fabricated on a normal filter paper with simple nano-printing method. Upconversion nanoparticles tagged with specific antibodies are printed to the test zones on the test paper, followed by the introduction of assay antigen. Upconversion fluorescence measurements are directly conducted on the test zones after the antigen-to-antibody reactions. Furthermore, a multi-channel test paper for simultaneous detection of multiple cancer biomarkers was established by the same method and obtained positive results. The device showed high anti-interfere, stability, reproducible and low detection limit (0.89 ng/mL), moreover it is very easy to fabricate and operate, which is a promising prospect for a clinical point-of-care test.

The properties of paper products depend on the structure of the cellulose fibres therein. Although fibre properties in virgin pulps can be modified by a refining process, this is more difficult in pulp from recovered fibre, particularly waste from office shredders that tend to shorten fibres during shredding. The shorter fibres in shredded paper make it difficult to easily reconstitute them into high-quality paper products. Moreover, because of high energy usage during the recycling process and transportation inefficiencies, there is a need to determine how to responsibly shred paper to alleviate this environmental burden. With this in mind, the influence of initial fibre length on the tensile properties of paper was investigated. Changes in initial fibre length significantly influenced many pulp and paper properties. It was found that cutting the paper into pieces with an area less than 25 mm2 caused significant changes in the important morphological parameters of the fibres and a sharp decrease in the tensile properties of the reconstituted paper. [ABSTRACT FROM AUTHOR]