Search

This study investigates the potential use of Yellow River sand (YRS) sourced from the lower reaches of the Yellow River in China as a sustainable and cost-effective substitute for quartz sand in Engineered Cementitious Composites (ECC). With an annual accumulation of approximately 400 million tons in this region, YRS presents a substantial resource. ECC specimens with 100% YRS replacement with quartz sand were subjected to various curing methods: natural, steam, standard, and sprinkler. Extensive mechanical testing including flexural, compressive, uniaxial tensile, and four-point flexural tests was conducted. Additionally, Scanning Electron Microscope (SEM) and Mercury Intrusion Porosimetry (MIP) analyses investigated microscopic mechanisms influencing macroscopic mechanical properties. Finally, the mechanical properties of the YRS-ECC test block after 14 days of standard curing and the traditional sand ECC test block were compared and analyzed. The results indicate that ECC specimens with 100% YRS substitution under natural curing show an optimal ultimate tensile strain of more than 4%, providing the best resistance to the reduction in ultimate flexural load and deflection due to aging. Steam curing enhances flexural and compressive strength, achieving an ultimate flexural load of 5 kN and a maximum deflection of 4.42 mm at 90 days. SEM analysis revealed lower C-S-H gel density under natural curing and higher under steam curing, enhancing fiber pull-out in steam-cured specimens. The MIP tests demonstrated that natural curing had the highest porosity (32.86%) and average pore size (51.69 nm), whereas steam curing resulted in the smallest average pore size, with 44% of pores under 50 nm. Compared with traditional sand, it is found that the ultimate bending load and deflection of YRS-ECC are 5.7% and 9.4% higher than those of traditional sand ECC, respectively, and its ultimate tensile strength and strain are also improved. These findings highlight YRS as a sustainable alternative to natural sand in ECC, with natural curing proving the most effective for superior mechanical performance, including tensile strain, crack resistance, and durability. [ABSTRACT FROM AUTHOR]

Before artificial ageing, extruded aluminium profiles are subjected to stretching with a small cold deformation in the range of 0.5–2%. This deformation improves the geometrical stability of the extruded product and causes changes in the microstructure of the profile, which leads to the strain hardening of the material after artificial ageing. The work has resulted in the creation of the prototype of an original device, which is unique in the world, for the dynamic stretching of the extruded profiles after quenching. The semi-industrial unit is equipped with a hydraulic system for stretching and a pneumatic system for cold dynamic deformation. The aim of this research paper is to produce advantageous microstructural changes and increase the strength properties of the extruded material. The solution of the dynamic stretching of the profiles after extrusion is a great challenge and an innovation not yet practised. The paper presents the results of microstructural and mechanical investigations carried out on extruded AlMgSi(Cu) alloys quenched on the run-out table of the press, dynamically stretched under different conditions, and artificially aged for T5 temper. Different stretching conditions were applied: a static deformation of 0.5% at a speed of 0.02 m/s, and dynamic deformation of 0.25%, 0.5%, 1%, and 1.5% at speeds of 0.05 and 2 m/s. After the thermomechanical treatment of the profiles, microstructural observations were carried out using an optical microscope (OM) and a scanning electron microscope (SEM). A tensile test was also carried out on the specimens stretched under different conditions. In all the cases, the dynamically stretched profiles showed higher strength properties, especially those deformed at a higher speed of 2 m/s, where the increase in UTS was observed in the range of 7–18% compared to the classical (static) stretching. The microstructure of the dynamically stretched profiles is more homogeneous with a high proportion of fine dispersoids. [ABSTRACT FROM AUTHOR]

Geopolymers, as a novel cementitious material, exhibit typical brittle failure characteristics under stress. To mitigate this brittleness, fibers can be incorporated to enhance toughness. This study investigates the effects of varying polypropylene fiber (PPF) content and fiber length on the flowability, mechanical properties, and flexural toughness of coal gangue-based geopolymers. Microstructural changes and porosity variations within the Fiber-Reinforced Geopolymer Mortar(GMPF) matrix were observed using scanning electron microscope (SEM) and Low field NMR(LF-NMR) to elucidate the toughening mechanism of PPF-reinforced geopolymers. The introduction of fibers into the geopolymer matrix demonstrated an initial bridging effect in the viscous geopolymer slurry, with a 3.0 vol% fiber content reducing fluidity by 5.6%. Early mechanical properties of GMPF were enhanced with fiber addition; at 1.5 vol% fiber content and 15 mm length, the 3-day flexural and compressive strengths increased by 30.81% and 17.4%, respectively. Furthermore, polypropylene fibers significantly improved the matrix's flexural toughness, which showed an increasing trend with higher fiber content. At a 3.0 vol% fiber content, the flexural toughness index increased by 198.35%. The data indicated that a fiber length of 12 mm yielded the best toughening effect, with an 84.03% increase in the flexural toughness index. SEM observations revealed a strong interfacial bond between fibers and the matrix, with noticeable damage on the fiber surface due to frictional forces, and fiber pull-out being the predominant failure mode. Porosity testing results indicated that fiber incorporation substantially improved the internal pore structure of the matrix, reducing the median pore diameter of mesopores and converting mesopores to micropores. Additionally, the number of harmless and less harmful pores increased by 23.01%, while the number of more harmful pores decreased by 30.43%. [ABSTRACT FROM AUTHOR]

This paper presents research results on biocomposites made from a combination of extruded apple pomace (EAP) and potato starch (SP). The aim of this work was to investigate the basic properties of biocomposites obtained from extruded apple pomace reinforced with potato starch. The products were manufactured by hot pressing using a hydraulic press with a mould for producing samples. The prepared biocomposites were subjected to strength tests, surface wettability was determined, and a colour analysis was carried out. A thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), and cross-sectioning observed in a scanning electron microscope (SEM) were also performed. The obtained test results showed that the combination of apple pomace (EAP) and starch (SP) enabled the production of compact biocomposite materials. At the same time, it was found that each increase in the share of starch in the mixture for producing biocomposites increased the strength parameters of the obtained materials. With the highest share of starch in the mixture, 40%, and a raw material moisture content of 14%, the material had the best strength parameters and was even characterised by hydrophobic properties. It was also found that materials with a high content of starch are characterised by increased temperature resistance. The analysis of SEM microscopic photos showed well-glued particles of apple pomace, pectin, and gelatinised starch and a smooth external structure of the samples. Research and analyses have shown that apple pomace reinforced only with the addition of starch can be a promising raw material for the production of simple, biodegradable biocomposite materials. [ABSTRACT FROM AUTHOR]

High-strength metastable β titanium alloys are promising structural materials to be used in aviation industries. In order to achieve a high strength level, solid solution treatment within β region and subsequent low-temperature aging are usually necessary to obtain fine α precipitates. The selection of the aging temperature is considered critical to the mechanical performance of metastable β titanium alloys. In this work, we investigated the effect of aging temperature on the microscopic structure and mechanical properties of a novel type of titanium alloy TB18 (Ti-4.5Al-5Mo-5V-6Cr-1Nb). A series of aging treatments were conducted on TB18 specimens at 510 °C, 520 °C, 530 °C, and 540 °C after the solid solution treatment at 870 °C. On the basis of the systematic results of scanning electron microscope and transmission electron microscope, the behavior of the α phases affected by the varied aging temperatures were studied. As the aging temperature rose, the grain width of the α phase increased from 60 nm (510 °C) to 140 nm (540 °C). For the TB18 samples aged at 510 °C and 540 °C, the tensile strength/yield strength/impact toughness values were 1365 ± 3 MPa/1260 ± 0.9 MPa/26.5 ± 1.2 J/cm2 and 1240 ± 0.9 MPa/1138 ± 0.8 MPa/36.2 ± 1.3 J/cm2, respectively. As a result, the tensile performance and the grain width of the α phase agreed well with the Hall–Petch relationship. This work offers valuable support for both theoretical analyses and the heat treatment strategies on the novel TB18 titanium alloy. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA) has been widely used in many fields because of its good biodegradability, biocompatibility, and renewability. This work studied the degradation behavior and mechanical properties of cellulose nanofiber (CNF)/PLA composites. In vitro degradation experiments of 3D-printed samples were conducted at elevated temperatures, and the degradation characteristics were evaluated by mechanical tests, gel permeation chromatography (GPC), differential scanning calorimetric (DSC), and scanning electron microscope (SEM). The results indicated that the addition of CNF (0.5 wt%) accelerated the degradation rate of PLA. The decreases in number average molecular weight ( M n ) and weight average molecular weight  (M w)  of composites were 7.96% and 4.91% higher than that of neat PLA, respectively. Furthermore, the tensile modulus of composites was 18.4% higher than that of neat PLA, while the strength was 7.4% lower due to poor interfacial bonding between CNF and PLA. A mapping relationship between accelerated and normal degradation showed that the degradation experienced during 60 days at 37 °C was equivalent to that undergone during 14 days at 50 °C; this was achieved by examining the alteration in  M n . Moreover, the degradation process caused a notable deformation in the samples due to residual stress generated during the 3D printing process. This study provided valuable insights for investigating the in vitro degradation behavior of 3D-printed products. [ABSTRACT FROM AUTHOR]

This paper presents an experimental study of the wet freeze–thaw (FT) durability of a fibre–polymer composite produced by vacuum infusion using an innovative bio-based unsaturated polyester resin (UPR) and basalt fibres. As the benchmark, an equivalent composite produced with a conventional (oil-based) UPR was also tested. The composites were preconditioned in water immersion for 30 days at 20 °C followed by exposure to wet FT for up to 300 cycles; each FT cycle consisted of 3 h in dry freezing condition (−20 °C) and 8 h in thawing condition (23 °C) submerged in water. The composites' properties were assessed after preconditioning and after 100, 200, and 300 FT cycles, through mechanical (tensile, compressive, in-plane shear, interlaminar shear) and thermomechanical (dynamic mechanical analysis) tests. Gravimetric and scanning electron microscope analyses were also carried out. The results obtained show that the preconditioning stage, involving water immersion, caused most of the damage, with property reductions of 5% to 39% in the bio-composite, while in the oil-composite they ranged between 4% and 22%, being higher for matrix-dominated properties. On the other hand, FT alone had an insignificant effect on the degradation of material properties; after exposure to FT, property recovery was observed, specifically in matrix-dominated properties, such as interlaminar shear strength, which recovered by 12% in the bio-composite during exposure to FT. The overall performance of the bio-composite was inferior to the conventional one, especially during the preconditioning stage, and this was attributed to the hydrophilicity of some of the components of its bio-based resin. [ABSTRACT FROM AUTHOR]

The current work investigates the possibility of fabricating additive manufacturing products in solid-state form, from AA2011-T6 of 40 mm diameter rods as a feedstock, using an additive friction stir deposition (A-FSD) technique. The use of large diameter feedstocks, especially high-strength aluminum alloys (2XXX series), is a challenge, as it necessitates high power and the critical selection of the optimal A-FSD parameters, such as feed rate and spindle rotation speed. The study included applying a wide range of spindle rotation speeds, ranging from 400 to 1200 rpm, at three levels of feeding rates of 1, 3, and 5 mm/min. The AA2011-T6 friction stir deposited parts (FSDPs) were visually evaluated. This was followed by an examination of macrostructures through the thickness of the fabricated specimens. The characterization of microstructures was also carried out using optical microscopy and a scanning electron microscope equipped with advanced EDS analysis. Furthermore, the mechanical properties in terms of hardness and compressive strength of the AA2011-T6 base material (BM) and deposited materials were evaluated. Sound, additively manufactured products were successfully fabricated from 40 mm diameter AA2011-T6 feedstocks using the suggested deposition variables of 600 and 800 rpm spindle speeds and feeding rates of 1, 3, and 5 mm/min. The results indicated that the spindle speed and feeding rate govern the quality of the FSDPs. Furthermore, the axial load during the A-FSD process increased with increasing these parameters. In comparison to the AA2011-T6 BM, the additively deposited materials showed a refined grain structure and uniform dispersion of the fragment precipitates in their continuous multi-layers. The reduction ratio in grain size attains 71.56%, 76%, and 81.31% for the FSDPs processed at 800 rpm spindle speed and feeding rates of 1, 3 and 5 mm/min, respectively, compared to the grain size of BM. The Al2Cu and Al7Cu2Fe intermetallics are detected in the AA2011-T6 BM, and their deposited parts are in different shapes of spherical, almost spherical, irregular, and rod-like shapes. The compressive strength and hardness of the deposited parts increased with increasing spindle speed and feeding speeds. At a spindle speed of 800 rpm and a 5 mm/min feeding rate, the higher hardness and compressive strength gained were 85% and 93%, respectively, from that of the AA2011-T6 feedstock. [ABSTRACT FROM AUTHOR]

This study examines the impacts of copper and boron in parts per million (ppm) on the microstructure and mechanical properties of spheroidal graphite cast iron (SCI). Boron's inclusion increases the ferrite content whereas copper augments the stability of pearlite. The interaction between the two significantly influences the ferrite content. Differential scanning calorimetry (DSC) analysis indicates that boron alters the enthalpy change of the α + Fe3C → γ conversion and the α → γ conversion. Scanning electron microscope (SEM) analysis confirms the locations of copper and boron. Mechanical property assessments using a universal testing machine show that the inclusion of boron and copper decreases the tensile strength and yield strength of SCI, but simultaneously enhances elongation. Additionally, in SCI production, the utilization of copper-bearing scrap and trace amounts of boron-containing scrap metal, especially in the casting of ferritic nodular cast iron, offers potential for resource recycling. This highlights the importance of resource conservation and recycling in advancing sustainable manufacturing practices. These findings provide critical insights into the effects of boron and copper on SCI's behavior, contributing to the design and development of high-performance SCI materials. [ABSTRACT FROM AUTHOR]

The effect of different heat inputs of 1.45 kJ/mm, 1.78 kJ/mm and 2.31 kJ/mm on the microstructure and mechanical properties of deposited metals of the self-developed AWS A5.28 E120C-K4 high strength steel flux-cored wire was studied by optical microscope, scanning electron microscope and mechanical property test. With the increase in heat input, the results showed that the microstructure of deposited metals became coarse. Acicular ferrite increased at first and then decreased, granular bainite increased and degenerated upper bainite and martensite decreased slightly. Under the low heat input of 1.45 kJ/mm, the cooling rate was fast and the element diffusion was uneven, which caused composition segregation and easy to form large size inclusions SiO2-TiC-CeAlO3 with weak binding to the matrix. Under the middle heat input of 1.78 kJ/mm, the composite rare earth inclusions in dimples were mainly TiC-CeAlO3. The dimples were small and uniformly distributed, and the dimple fracture mainly depended on the wall-breaking connection between medium-sized dimples rather than an intermediate media. Under the high heat input of 2.31 kJ/mm, SiO2 was easy to adhere to high melting point Al2O3 oxides to form irregular composite inclusions. Such irregular inclusions do not need to absorb too much energy to form necking. Finally, the integrated effects of microstructure and inclusions resulted in the optimum mechanical properties of deposited metals with a heat input of 1.78 kJ/mm, which was a tensile strength of 793 MPa and an average impact toughness at −40 °C of 56 J. [ABSTRACT FROM AUTHOR]

The setting time of alkali-activated slag (AAS) binders is extremely short, while traditional retarders of Portland cement may be invalid for AAS. To find an effective retarder with a less negative impact on strength, borax (B), sucrose (S), and citric acid (CA) were selected as potential retarders. The setting time of AAS with different admixtures dosages of 0%, 2%, 4%, 6%, and 8%, and the unconfined compressive strength and beam flexural strength of 3 d, 7 d, and 28 d AAS mortar specimens were tested. The microstructure of AAS with different additives was observed by scanning using an electron microscope (SEM), and the hydration products were analyzed by energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), and thermogravimetric analysis (DT-TGA) to explain the retarding mechanism of AAS with different additives. The results showed that the incorporation of borax and citric acid could effectively prolong the setting time of AAS more than that of sucrose, and the retarding effect is more and more obvious with the increase in borax and citric acid dosages. However, sucrose and citric acid negatively influence AAS's unconfined compressive strength and flexural stress. The negative effect becomes more evident with the increase in sucrose and citric acid dosages. Borax is the most suitable retarder for AAS among the three selected additives. SEM-EDS analysis showed that the incorporation of borax does three things: produces gels, covers the surface of the slag, and slows down the hydration reaction rate. [ABSTRACT FROM AUTHOR]

Al-Cu alloy has broad application prospects in the field of aerospace due to its excellent performance. In this paper, deposits with different Cu contents were prepared by the wire arc additive manufacturing (WAAM) process, and the effects of Cu content on the microstructure and mechanical properties were investigated. The microstructure of Al-Cu alloy was investigated by metallography, scanning electron microscope (SEM), energy-dispersive spectrometer (EDS), and transmission electron microscope (TEM). The results show that both the number and size of the precipitated θ phases (Al2Cu) in the as-deposited material increase with the increase of Cu content. After the T4 treatment, the solid solution amount of Cu in the matrix showed a trend of first increasing and then remaining stable. When the content of Cu was greater than 5.65%, as the Cu content increased, the number and size of the remaining θ phases both increased. In the peak ageing state, the amount of precipitated θ' phase showed a trend of increasing and then remaining stable. After the T6 treatment, the mechanical properties showed a trend of first increasing and then decreasing with the increase of the content of Cu. When the Cu content was 5.65%, the deposit achieved the best mechanical properties, and the anisotropy of the mechanical properties disappeared. The tensile strength, yield strength, and elongation reached 538 MPa, 478 MPa, and 10.5%, respectively. When the content of Cu was greater than 5.65%, the anisotropy of mechanical properties was obvious, and the fracture mode of the vertical specimen changed from ductile fracture to brittle fracture. [ABSTRACT FROM AUTHOR]

To reveal the deterioration process of magnesium oxychloride cement (MOC) in an outdoor, alternating dry–wet service environment, the evolution of the macro- and micro-structures of the surface layer and inner core of MOC samples as well as their mechanical properties and increasing dry–wet cycle numbers were investigated by using a scanning electron microscope (SEM), an X-ray diffractometer (XRD), a simultaneous thermal analyser (TG-DSC), a Fourier transform infrared spectrometer (FT-IR), and an microelectromechanical electrohydraulic servo pressure testing machine. The results show that as the number of dry–wet cycles increases, the water molecules gradually invade the interior of the samples, causing the hydrolysis of P 5 (5Mg(OH)2·MgCl2·8H2O) and hydration reactions of unreacted active MgO. After three dry–wet cycles, there are obvious cracks on the surface of the MOC samples, and they suffer from warped deformation. The microscopic morphology of the MOC samples changes from a gel state and a short, rod-like shape to a flake shape, which is a relatively loose structure. Meanwhile, the main phase composition of the samples becomes Mg(OH)2, and the Mg(OH)2 contents of the surface layer and inner core of the MOC samples are 54% and 56%, respectively, while the P 5 amounts are 12% and 15%, respectively. The compressive strength of the samples decreases from 93.2 MPa to 8.1 MPa and reduces by 91.3%, and their flexural strength declines from 16.4 MPa to 1.2 MPa. However, their deterioration process is delayed compared with the samples that were dipped in water continuously for 21 days whose compressive strength is 6.5 MPa. This is primarily ascribed to the fact that during the natural drying process, the water in the immersed samples evaporates, the decomposition of P 5 and the hydration reaction of unreacted active MgO both slow down, and the dried Mg(OH)2 may provide the partial mechanical properties, to some extent. [ABSTRACT FROM AUTHOR]

The effect of hydroxyapatite (HAp) synthesized by the chemical precipitation process on the morphology and properties of composites based on poly(lactic acid) (PLA) was investigated at various filler content ratios, i.e., 5, 10 and 15 wt%. Both neat PLA and PLA-based composites were first prepared using the solvent casting method, followed by melt compounding in an internal mixer, whereas tensile specimens were obtained by thermo-compression. The study revealed that the addition of 5 wt% of HAp into the PLA led to a slight improvement in both the thermal stability and tensile properties of the composite material in comparison with neat PLA and other composite samples. Indeed, the values of the tensile strength and modulus increased from approximately 61 MPa and 2.9 GPa for the neat PLA to almost 64 MPa and 3.057 GPa for the composite sample, respectively. Moreover, the degradation temperature at a 5 wt% mass loss also increased by almost 5 °C compared to other samples, due probably to a finer dispersion of the HAp particles in the PLA, as observed under a scanning electron microscope. Furthermore, the FT-IR spectra displayed some changes in the chemical structure of the PLA/HAp (5 wt%), indicating the occurrence of filler-matrix interactions. At a higher filler content ratio, a decrease in the properties of the PLA/HAp composites was observed, being more pronounced at 15 wt%. The PLA composite containing 5 wt% HAp presents the best compromise among the investigated properties. The study highlighted the possibility of using HAp without any prior surface treatment as a reinforcement in PLA composite materials. [ABSTRACT FROM AUTHOR]

The mechanical properties of (Ti, Nb)B/Ti2AlNb composites were expected to improve further by utilizing spark plasma sintering (SPS) and inducing the novel three-dimensional network architecture. In this study, (Ti, Nb)B/Ti2AlNb composites with the novel architecture were successfully fabricated by ball milling the LaB6 and Ti2AlNb mixed powders and subsequent SPS consolidation. The influence of the (Ti, Nb)B content on the microstructure and mechanical properties of the composites was revealed by using the scanning electron microscope (SEM), transmission electron microscopy (TEM) and electronic universal testing machine. The microstructural characterization demonstrated that the boride crystallized into a B27 structure and the α2-precipitated amount increased with the (Ti, Nb)B increasing. When the (Ti, Nb)B content reached 4.9 vol%, both the α2 and reinforcement exhibited a continuous distribution along the prior particle boundaries (PPBs). The tensile test displayed that the tensile strength of the composites presented an increasing trend with the increasing (Ti, Nb)B content followed by a decreasing trend. The composite with a 3.2 vol% reinforcement had the optimal mechanical properties; the yield strengths of the composite at 25 and 650 °C were 998.3 and 774.9 MPa, showing an 11.8% and 9.2% improvement when compared with the Ti2AlNb-based alloy. Overall, (Ti, Nb)B possessed an excellent strengthening effect and inhibited the strength weakening of the PPBs area at high temperatures; the reinforcement content mainly affected the mechanical properties of the (Ti, Nb)B/Ti2AlNb composites by altering the α2-precipitated amount and the morphology of (Ti, Nb)B in the PPBs area. Both the continuous precipitation of the brittle α2 phase and the agglomeration of the (Ti, Nb)B reinforcement dramatically deteriorated the mechanical properties. [ABSTRACT FROM AUTHOR]

This study shows the results of Ni replacement with Co in a W-Ni-Co-type tungsten heavy alloy (WHA) in terms of the structure and mechanical properties. Five alloys containing 92 wt. % of tungsten plus Ni and Co changing in the proportions (Co:Ni) of 1:9, 2:8, 3:7, 4:6, and 5:5 were prepared using liquid phase sintering (LPS). The specimens were studied directly after sintering and after solution heat treatment. The tensile strength, yield strength, and elongation were evaluated. The results of tensile tests were supplemented with microhardness measurements of tungsten grains and matrix. Light microscopy was used for the microstructure, and a scanning electron microscope (SEM) equipped with an EDS attachment was applied for the assessment of the fracture mode and chemical microanalysis. It was concluded that the replacement of Ni with Co led to a tensile property increase that was accompanied by a gradual decrease in elongation that started to be critical for a Co:Ni ratio higher than 4:6. [ABSTRACT FROM AUTHOR]

In this paper, glass fiber fabric reinforced polyphenylene sulfide composites were prepared by hot pressing. The effects of glass fibre modification and hot pressing temperature on the properties of the composites were investigated using a scanning electron microscope, infrared spectrometer, universal testing machine, and DIGEYE digital imaging colour measurement system. The results show that after the treatment with a silane coupling agent, the silane coupling agent was more uniformly distributed on the surface of the glass fibres, and the bonding effect between the glass fibre fabric and polyphenylene sulphide was significantly improved. The strength of the composites increased and then decreased with the increase of hot pressing temperature, and the surface colour of the composites became darker and darker. When the hot-pressing temperature is 310 °C, the mechanical properties of glass fabric-reinforced polyphenylene sulfide composites are at their best, the tensile strength reaches 51.9 MPa, and the bending strength reaches 78 MPa. [ABSTRACT FROM AUTHOR]

In this study, thermophysical and mechanical tests were conducted on sandstone samples from room temperature to 1000 °C. Based on the test results, the thermophysical properties (such as specific heat capacity, thermal conductivity, and thermal expansion coefficient) of sandstone after high-temperature treatment and the variations of mechanical properties (including peak strength, peak strain, elastic modulus, and whole stress-strain curve) with temperature were analyzed. Indeed, the deterioration law of sandstone after high-temperature treatment was also explored with the aid of a scanning electron microscope (SEM). The results show that with the increase in temperature, the specific heat capacity and thermal expansion coefficient of sandstone samples after high-temperature treatment increase first and then decrease, while the thermal conductivity gradually decreases. The range from room temperature to 1000 °C witnesses the following changes: As temperature rises, the peak strength of sandstone rises initially and falls subsequently; the elastic modulus drops; the peak strain increases at an accelerated rate. Temperature change has a significant effect on the deterioration rules of sandstone, and the increase in temperature contributes to the transition in the failure mode of sandstone from brittle failure to ductile failure. The experimental study on the thermophysical and mechanical properties of sandstone under the action of high temperature and overburden pressure has a guiding significance for the site selection and safety evaluation of UCG projects. [ABSTRACT FROM AUTHOR]

To study the effect of SAP incorporation on the early shrinkage of SAP internally cured concrete with the aim to solve the problems of early shrinkage and cracking of bridge leveling-layer concrete, using the SAP incorporation method as a parameter, the mechanical properties test of internally cured concrete, the shrinkage performance test of ring restraint and the scanning electron microscope observation test were carried out. The effects of the SAP content and incorporation method on the flowability, mechanical properties, shrinkage performance and microstructure of internally cured concrete were analyzed. The experimental results show that when the content of the SAP in concrete is 0.2% of the mass of cementitious materials, it has the least influence on the compressive strength of concrete. The addition of preabsorbed water to the SAP can delay early cement hydration, increase the later cement hydration rate and final hydration degree, and improve the concrete strength. Preabsorbed water mixed with an SAP can effectively improve the shrinkage of concrete, and the shrinkage reduction effect is more obvious than that from the dry addition of the SAP; the early cracking risk of concrete without an SAP is high, and it will crack before day 28. The addition of an SAP can strengthen the microstructure of concrete and improve its density and crack resistance, effectively avoiding concrete cracking. It is recommended that the water-absorbent resin be incorporated in a preabsorbent manner, and the SAP preabsorbent ratio is equal to the maximum water storage rate of the SAP. [ABSTRACT FROM AUTHOR]

In this work, mechanical properties of reinforced polypropylene composites were studied. PP in particulates shape with two different melt flow indexes (MFI) was used, i.e., 3 and 23 g/10 min, namely PP3 and PP23, respectively. Three different materials, namely TiO2 nanoparticle (nTiO2, spherical, 0D), micro-size short carbon fiber (SCF, fiber, 1D), and graphite nanoplatelet (GNP, sheet, 2D), were used as reinforcements/fillers. PP and fillers (in the desired composition) were first pre-mixed by a mechanical mixer. The mixture was then fed to a co-rotating twin-screw extruder for melt-compounding, followed by injection molding to fabricate testing samples. The microstructure and fracture surface of the composites were observed by a scanning electron microscope (SEM). Additionally, tensile, flexural, impact, and hardness tests were conducted to evaluate their mechanical properties. The SEM images stipulate that PP23 had better adhesion and dispersion with the fillers. The results from the SEM images support the mechanical testing results. PP23 composites exhibited more significant improvement in mechanical properties in comparison to PP3. At 5 wt. % filler loading, PP/GNP composite exhibited a greater improvement in mechanical properties compared with two other composites, which are PP/SCF and PP/nTiO2 composites for both PPs. [ABSTRACT FROM AUTHOR]

The effects of La and Y on the microstructure and mechanical properties of cast Al-Si-Cu alloys were investigated by X-ray diffractometer (XRD), optical microscope (OM), and scanning electron microscope (SEM). The results indicated that the addition of La and Y had a great effect on the refinement of α-Al grains, the modification of eutectic Si phase, and the reduction of β-Al5FeSi length in Al-Si-Cu alloys. The A380 + 0.6 wt.% La/Y alloy exhibited the best microstructure and mechanical properties. The UTS and EI of the A380 + 0.6 wt.% La/Y alloy were 215.3 MPa and 5.1%, which were 22.9% and 37.8% higher than those of the matrix alloy, respectively. In addition, neither Al11La3 nor Al3Y generated by the addition of La and Y could not serve as the nucleation core of α-Al grains, so the grain refinement of α-Al originated from the growth limitation and constitutional supercooling. Since La and Y promote twinning generation and constitutional supercooling, the eutectic Si phase also changed from stripe-like to short fibrous or even granular and was significantly refined. Furthermore, thermodynamic calculations indicated that the Al11La3 phase was formed first and the Al3Y phase was generated on the Al11La3 phase. [ABSTRACT FROM AUTHOR]

The application of CO2 curing on sludge ceramsite may improve its mechanical properties, and then increase the corresponding corrosion resistance. In this study, the influence of CO2-cured sludge ceramsite on the strength and long-term properties of cement concrete is investigated. CO2 curing time ranges from 0 h to 2 d. The cylinder compressive strength and water absorption rate of CO2-cured sludge ceramsite are first determined. Additionally, the flexural and compressive strengths, the chloride permeability and the freeze—thaw damage, as well as the corresponding thermal conductivity of cement concrete, are tested. Furthermore, the corrosion resistance of reinforcement inner-sludge-ceramsite cement concrete is measured. Finally, the scanning electron microscope photos of sludge ceramsite are obtained. Results show that the cylinder compressive strength of CO2-cured sludge ceramsite is 15.1, ~34.2% higher than that of sludge ceramsite. Meanwhile, the water absorption rate of CO2-cured sludge ceramsite is 39.6, ~82.4% higher than that of sludge ceramsite. The compressive strength and the flexural strength of cement concrete with CO2-cured sludge ceramsite are 11.4 and 18.7, ~21.6% and ~31.5% higher than the cement concrete with sludge ceramsite, respectively. The resistance of NaCl freeze—thaw cycles, determined by comparing the mass loss rate and the loss rates of mechanical strengths, is effectively improved by CO2 curing, while the thermal conductivity of cement concrete is decreased by CO2 curing. The corrosion resistance of inner reinforcement is improved by the application of CO2 curing on sludge ceramsite. [ABSTRACT FROM AUTHOR]

There is a need to develop new construction materials with improved mechanical performance and durability that are low-priced and have environmental benefits at the same time. This paper focuses on the rheological, mechanical, morphological, and durability properties of synthetic and steel fiber reinforced self-compacting concrete (SCC) containing 5–15% metakaolin (M) by mass as a green replacement for Portland cement. Testing of the fresh mixes included a slump-flow test, density, and porosity tests. Mechanical properties were determined through compression and flexural strength. A rapid chloride penetrability test (RCPT) and the chloride migration coefficient were used to assess the durability of the samples. A scanning electron microscope (SEM) with energy dispersion spectrometry (EDS) was used to study the concrete microstructure and the interfacial transition zone (ITZ). The results show that a combination of metakaolin and hybrid fibers has a negative effect on the flowability of SCC. In contrast, the inclusion of M and hybrid fibers has a positive effect on the compressive and flexural strength of SCC. The fracture of SCC samples without fibers was brittle and sudden, unlike the fiber-reinforced SCC samples, which could still transfer a considerable load with increasing crack mouth opening deflection. Overall, the chloride migration coefficients were reduced by up to 71% compared to the control mix. The chloride reduction is consistent with the resulting compact concrete microstructure, which exhibits a strong bond between fibers and the concrete matrix. [ABSTRACT FROM AUTHOR]

To study the heat-treatment process of a semi-solid copper alloy, a thixotropic back-extruded tin–bronze shaft sleeve was heat-treated at 630 °C, 660 °C, 690 °C and 720 °C for 1 h, respectively. Microstructure changes and mechanical properties under different solution temperatures of shaft sleeve were characterized using a metallographic microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM), hardness tester, and tensile tester. The results show that the tensile strength first increases and then decreases; the elongation decreases; and the Brinell hardness increases gradually with increasing solution temperature. When the solution treatment is at 690 °C, the tin–bronze shaft sleeve's microstructure and comprehensive mechanical properties are the best. The shape factor is 0.75, the average grain size is 82.52 μm, the Brinell hardness is 122 HBW, the tensile strength is 437 MPa, and the elongation is 17.4%, which is 3.4 times higher than that before solution treatment. [ABSTRACT FROM AUTHOR]

Industrial solid waste red mud discharge has caused serious environmental problems. This study utilized red mud as an additive to loessial silt being used for roadway subgrade material. In this study, unconfined compressive test, direct shear test, electrical resistivity test, and hydraulic conductivity test were conducted on red mud stabilized loessial silt (RMLS) with different red mud dosage (DR) to investigate DR effect on mechanical-electrical-hydro properties. Scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses were carried out to reveal the mechanism from micro perspective. The results showed addition of appropriate amount of red mud (30–42%) effectively improved unconfined compressive strength of treated loessial silt but reduced resistivity and hydraulic conductivity. Significant correlation between resistivity and strength performance of RMLS mixture was developed. Microscopic analysis indicates red mud addition will promote generation of hydration products such as calcium silicate hydrations (C-S-H), calcium silicate aluminates hydrations (C-A-S-H), and ettringite (Aft), which will tightly connect surrounding particles of loessial silt and hydrates. Red mud particles adhere to surface of soil particles and fill in pores between them improving a compact and stable structure. This study demonstrated the feasibility of using red mud as a stabilization material for roadway subgrade and proved that resistivity measurement is a nondestructive testing method to evaluate mechanical properties for RMLS mixture. [ABSTRACT FROM AUTHOR]

In the current work, mild steel used in shipbuilding applications was friction-stir-welded (FSWed) with the aim of investigating the microstructure and mechanical properties of the FSWed joints. Mild steel of 5 mm thickness was friction-stir-welded at a constant tool rotation rate of 500 rpm and two different welding speeds of 20 mm/min and 50 mm/min and 3° tool tilt angle. The microstructure of the joints was investigated using optical and scanning electron microscopes. Additionally, the grain structure and crystallographic texture of the nugget (NG) zone of the FSWed joints was investigated using electron backscattering diffraction (EBSD). Furthermore, the mechanical properties were investigated using both tensile testing and hardness testing. The microstructure of the low-welding-speed joint was found to consist of fine-grain ferrite and bainite (acicular ferrite) with an average grain size of 3 µm, which indicates that the temperature experienced above A1, where a ferrite and austenite mixture is formed, and upon cooling, the austenite transformed into bainite. The joint produced using high welding speed resulted in a microstructure consisting mainly of polygonal ferrite and pearlite. This could be due to the temperature far below A1 experienced during FSW. In terms of joint efficiency expressed in terms of relative ultimate tensile, the stress of the joint to the base material was found to be around 92% for the low-speed joint and 83% for the high-welding-speed joint. A reduction in welding was attributed to the microstructure, as well as the microtunnel defect formed near the advancing side of the joint. The tensile strain was preserved at 18% for low welding speed and increased to 24% for the high welding speed. This can be attributed to the NG zone microstructural constituents. In terms of crystallographic texture, it is dominated by a simple shear texture, with increased intensity achieved by increasing the welding speed. In both joints, the hardness was found to be significantly increased in the NG zone of the joints, with a greater increase in the case of the low-welding-speed joint. This hardness increase is mainly attributed to the fine-grained structure formed after FSW. [ABSTRACT FROM AUTHOR]

SiC-TiB2-TiC composites with matrices consisting of semiconductor material (SiC), conductive materials (TiB2-TiC), or their combination were fabricated by spark plasma sintering (SPS) at 2000 °C in a vacuum under a pressure of 80 MPa for 3 min. The composition and microstructure of the obtained composites were studied by X-ray diffraction and a scanning electron microscope equipped with an energy-dispersive detector. The flexural strength, Vickers hardness, and fracture toughness of SPSed samples were determined. Based on the observations in this work, three variations of the sintering process were proposed with different matrix compositions. The dense (99.7%) 60SiC-25TiB2-15TiC vol.% sintered ceramic composites exhibited the highest strength and hardness values of the studied composites, as well as a fracture toughness of 6.2 MPa·m1/2. [ABSTRACT FROM AUTHOR]

In the present paper, the designed thermomechanical process was applied to prepare ferrite/bainite multiphase microstructures in Si-rich low-alloy steel with a carbon content of 0.33 wt.% (0.33C) and 0.21 wt.% (0.21C). The microstructures were analyzed by scanning electron microscope, transmission electron microscope, and electron backscatter diffraction, and the mechanical properties (tensile and impact properties) were tested. The results showed that, on the premise of obtaining 15 vol.% ferrite in both steels, the ferrite grains in the 0.33C steel were polygonal with an average grain size of 2.2 μm, recrystallized more completely. However, the ferrite grains in the 0.21C steel were mainly long strip-shaped with a width of 2–4 μm, and the recrystallization degree was poor. In addition, upon increasing the austempering temperature, bainite ferrite laths were formed in the 0.33C steel, and the thickness was in the range of 81–123 nm. The morphology of bainite ferrite in the 0.21C steel gradually changed from lath to granular. Upon increasing the austempering temperature, the tensile strength and yield strength of both steels increased and the elongation decreased slightly. The impact energy of the two steels showed different trends upon increasing the austempering temperature, in which the impact energy of the 0.33C steel increased, while that of the 0.21C steel decreased. This is due to the difference size of the martensite-austenite constituents in the two steels. [ABSTRACT FROM AUTHOR]

Magnesium alloys are attractive for the production of lightweight parts in modern automobile and aerospace industries due to their advanced properties. Their mechanical properties are usually enhanced by the incorporation with reinforcement particles. In the current study, reinforced AZ31 magnesium alloy was fabricated through the addition of bulk Al and the incorporation of SiC nanoparticles using a stir casting process to obtain AZ31-SiC nanocomposites. Scanning electron microscope (SEM) investigations revealed the formation of Mg17Al12 lamellar intermetallic structures and SiC clusters in the nanocomposites. Energy dispersive spectroscopy (EDS) detected the uniform distribution of SiC nanoparticles in the AZ31-SiC nanocomposites. Enhancements in hardness and yield strength (YS) were detected in the fabricated nanocomposites. This behavior was referred to a joint strengthening mechanisms which showed matrix-reinforcement coefficient of thermal expansion (CTE) and elastic modulus mismatches, Orowan strengthening, and load transfer mechanism. The mechanical properties and wear resistance were gradually increased with an increase in SiC content in the nanocomposite. The maximum values were obtained from nanocomposites containing 1 wt% of SiC (AZ31-1SiC). AZ31-1SiC nanocomposite YS and hardness were improved by 27% and 30%, respectively, compared to AZ31 alloy. This nanocomposite also exhibited the highest wear resistance; its wear mass loss and depth of the worn surface decreased by 26% and 15%, respectively, compared to AZ31 alloy. [ABSTRACT FROM AUTHOR]

At present, the research on the high temperature degradation of concrete usually focuses on only the degradation of concrete itself without considering the effect of the plastering layer. It is necessary to take into account the influence of the plastering layer on the high temperature degradation of concrete. With an increase in the water/cement ratio, the explosion of concrete disappeared. Although increasing the water/cement ratio can alleviate the cracking of concrete due to lower pressure, it leads to a decrease in the mechanical properties of concrete after heating. It is proved that besides the water/cement ratio, the apparent phenomena and mechanical properties of concrete at high temperature can be affected by the plastering layer. The plastering layer can relieve the high temperature cracking of concrete, and even inhibit the high temperature explosion of concrete with 0.30 water/cement ratio. By means of an XRD test, scanning electron microscope test and thermogravimetric analysis, it is found that the plastering layer can promote the rehydration of unhydrated cement particles of 0.30 water/cement ratio concrete at high temperature and then promote the mechanical properties of concrete at 400 °C. However, the plastering layer accelerated the thermal decomposition of C-S-H gel of concrete with a water/cement ratio of 0.40 at high temperature, and finally accelerate the decline of mechanical property of concrete. To conclude, the low water/cement ratio and plastering layer can delay the deterioration of concrete at high temperature. [ABSTRACT FROM AUTHOR]

The aim of this paper is to promote the use of mine clay washing residues for the preparation of alkali activated materials (AAMs). In particular, the influence of the calcination temperature of the clayey by-product on the geopolymerization process was investigated in terms of chemical stability and durability in water. The halloysitic clay, a mining by-product, has been used after calcination and mixed with an alkaline solution to form alkali activated binders. Attention was focused on the influence of the clay's calcination treatment (450–500–600 °C) on the geopolymers' microstructure of samples, remaining in the lower limit indicated by the literature for kaolinite or illite calcination. The mixtures of clay and alkali activators (NaOH 8M and Na-silicate) were cured at room temperature for 28 days. The influence of solid to liquid ratio in the mix formulation was also tested in terms of chemical stability measuring the pH and the ionic conductivity of the eluate after 24-h immersion time in water. The results reported values of ionic conductivity higher for samples made with untreated clay or with low temperature of calcination (≥756 mS/m) compared with values of samples made with calcined clay (292 mS/m). This result suggests that without a proper calcination of the as-received clay it was not possible to obtain 25 °C-consolidated AAMs with good chemical stability and dense microstructure. The measures of integrity test, pH, and ionic conductivity in water confirmed that the best sample is made with calcined clay at 600 °C, being similar (53% higher ionic conductivity of the eluate) or equal (integrity test and pH) to values recorded for the metakaolin-based geopolymer considered the reference material. These results were reflected in term of reticulation and morphology of samples through the analysis with scanning electron microscope (SEM) and X-ray diffraction (XRD), which show a dense and homogeneous microstructure predominantly amorphous with minor amounts of quartz, halloysite, and illite crystalline phases. Special attention was dedicated to this by-product to promote its use, given that kaolinite (and metakaolin), as primary mineral product, has a strong impact on the environment. The results obtained led us to consider this halloysite clay very interesting as an aluminosilicate precursor, and extensively deepening its properties and reactivity for the alkaline activation. In fact, the heart of this work is to study the possibility of reusing this by-product of an industrial process to obtain more sustainable high-performance binders. [ABSTRACT FROM AUTHOR]

In the present paper, the Mg-11Gd-2Y-1Zn alloys with different Al addition were fabricated by the gravity permanent mold method. The effect of Al content on microstructure evolution and mechanical properties of as-cast Mg-11Gd-2Y-1Zn alloy was studied by metallographic microscope, scanning electron microscope, XRD and tensile testing. The experimental results showed that the microstructure of as-cast Mg-11Gd-2Y-1Zn alloy consisted of α-Mg phase and island-shaped Mg3 (RE, Zn) phase. When Al element was added, Al2RE phase and lamellar Mg12REZn (LPSO) phase were formed in the Mg-11Gd-2Y-1Zn alloy. With increasing Al content, LPSO phase and Mg3 (RE, Zn) phase gradually decreased, while Al2RE phase gradually increased. There were only α-Mg and Al2RE phases in the Mg-11Gd-2Y-1Zn-5Al alloy. With the increase of Al content, the grain size decreased firstly and then increased. When the Al content was 1 wt.%, the grain size of the alloy was the minimum value (28.9 μm). The ultimate tensile strength and elongation increased firstly and then decreased with increasing Al addition. And the fracture mode changed from intergranular fracture to transgranular fracture with increasing addition. When Al addition was 1 wt.%, the maximum ultimate tensile strength reached 225.6 MPa, and the elongation was 7.8%. When the content of Al element was 3 wt.%, the maximum elongation reached 10.2% and the ultimate tensile strength was 207.7 MPa. [ABSTRACT FROM AUTHOR]

Iron ore tailings (IOTs) are gradually used as building materials to solve the severe ecological and environmental problems caused by their massive accumulation. However, the bulk density of IOT as aggregate is too large, which seriously affects the concrete properties. Therefore, in this paper, the effect of hydroxypropyl methylcellulose (HPMC) on the workability, mechanical properties, and durability of concrete prepared from IOT recycled aggregate was studied. The action mechanism of HPMC on the workability and the mechanical properties of the IOT concrete was analyzed by mercury intrusion porosimetry (MIP) and scanning electron microscope (SEM). The results show that HPMC can effectively improve the segregation problem caused by the sinking and air entrainment of IOT aggregate and improve the crack resistance of concrete with little effect on its compressive strength and electric flux. These results are due to the air-entraining thickening effect of HPMC, which improves the slurry viscosity, hinders the sinking of aggregate, and improves the workability. At the same time, HPMC film, after concrete hardening, will bridge the slurry and aggregate through physical and chemical effects, hinder the propagation of microcracks, and improve the crack resistance. [ABSTRACT FROM AUTHOR]

Electrospinning is an innovative new fibre technology that aims to design and fabricate membranes suitable for a wide range of tissue engineering (TE) applications including vascular grafts, which is the main objective of this research work. This study dealt with fabricating and characterising bilayer structures comprised of an electrospun sheet made of polycaprolactone (PCL, inner layer) and an outer layer made of poly lactic-co-glycolic acid (PLGA) and a coaxial porous scaffold with a micrometre fibre structure was successfully produced. The membranes' propriety for intended biomedical applications was assessed by evaluating their morphological structure/physical properties and structural integrity when they underwent the degradation process. A scanning electron microscope (SEM) was used to assess changes in the electrospun scaffolds' structural morphology such as in their fibre diameter, pore size (μm) and the porosity of the scaffold surface which was measured with Image J software. During the 12-week degradation process at room temperature, most of the scaffolds showed a similar trend in their degradation rate except the 60 min scaffolds. The coaxial scaffold had significantly less mass loss than the bilayer PCL/PLGA scaffold with 1.348% and 18.3%, respectively. The mechanical properties of the fibrous membranes were measured and the coaxial scaffolds showed greater tensile strength and elongation at break (%) compared to the bilayer scaffolds. According to the results obtained in this study, it can be concluded that a scaffold made with a coaxial needle is more suitable for tissue engineering applications due to the improved quality and functionality of the resulting polymeric membrane compared to the basic electrospinning process. However, whilst fabricating a vascular graft is the main aim of this research work, the biological data will not present in this paper. [ABSTRACT FROM AUTHOR]

Polymer-modified concrete and fiber concrete are two excellent paving materials that improve the performance of some concrete, but the performance of single application material is still limited. In this paper, polymer-modified concrete with strong deformation and fiber concrete with obvious crack resistance and reinforcement effect were compounded by using the idea of composite material design so as to obtain a high-performance pavement material. The basic mechanical properties of high-content hybrid fiber–polymer-modified concrete, such as workability, compression, flexural resistance, and environmental durability (such as sulfate resistance) were studied by using the test regulations of cement concrete in China. The main results were as follows. (1) The hybrid fiber–polymer concrete displayed reliable working performance, high stiffness, and a modulus of elasticity as high as 35.93 GPa. (2) The hybrid fiber–polymer concrete had a compressive strength of 52.82 MPa, which was 31.2% higher than that of the plain C40 concrete (40.25 MPa); the strength of bending of the hybrid concrete was 11.51 MPa, 191.4% higher than that of the plain concrete (3.95 MPa). (3) The corrosion resistance value of the hybrid fiber–polymer concrete was 81.31%, indicating its adjustability to sulfate attack environments. (4) According to cross-sectional scanning electron microscope (SEM) images, the hybrid fiber–polymer concrete was seemingly more integrated with a dense layer of cementing substance on its surface along with fewer microholes and microcracks as when compared to the ordinary concrete. The research showed that hybrid fiber–polymer concrete had superior strength and environmental erosion resistance and was a pavement material with superior mechanical properties. [ABSTRACT FROM AUTHOR]

The paper deals with research related to the production of metal cellular aluminium systems, in which production is based on the application of sodium chloride particles. In this paper, the properties of porous aluminium materials that were produced by an unconventional method—by pressing salt particles into the melt of aluminium alloy—are described. The new methodology was developed and verified for the production of these materials. The main feature of this methodology is a hydraulic forming press and a simple-shaped foundry mould. For these purposes, four different groups of sodium chloride particle sizes (1 to 3, 3 to 5, 5 to 7 and 8 to 10 mm) were applied. The preferred aluminium foundry alloy (AlSi12) was used to produce the porous aluminium samples. Based upon this developed methodology, samples of porous aluminium materials were produced and analysed. Their weight and volume were monitored, their density and relative density were calculated, and their porosity was determined. In addition, the porosity of samples and continuity of their air cells were monitored as well. An industrial computed tomograph and a scanning electron microscope were applied for these purposes. [ABSTRACT FROM AUTHOR]