Search

We present a new route for obtaining surface-tethered polymer films containing pendant catechol functional groups via surface-initiated activators regenerated by electron-transfer atom-transfer radical polymerization (SI-ARGET ATRP) of glycidyl methacrylate (GMA) and post-polymerization modification of the resulting poly(glycidyl methacrylate) (pGMA) films with dopamine. This method enables a high degree of functionalization of pGMA films with catechol groups at a controlled level, depending on the duration of the post-polymerization modification reaction. The dopamine-pGMA films readily absorbs Al 3+ and Zn 2+ ions, as verified by quartz crystal microbalance with dissipation (QCM-D) under continuous flow conditions, and demonstrates a four-fold molar selectivity to Al 3+ over Zn 2+ . The ions desorb from the films upon rinsing with pure deionized (DI) water, which regenerates the catechol sites in the dopamine-pGMA film. Subsequent exposure to metal ions after rinsing steps yields reproducible levels of loading.

The design of electrode interfaces to achieve efficient electron transfer to biomolecules is important in many bioelectrochemical processes. Within the field of biohybrid solar energy conversion, constructing multilayered Photosystem I (PSI) protein films that maintain good electronic connection to an underlying electrode has been a major challenge. Previous shortcomings include low loadings, long deposition times, and poor connection between PSI and conducting polymers within composite films. Here, we show that PSI protein complexes can be deposited into monolayers within a 30 min timespan by leveraging the electrostatic interactions between the protein complex and the poly(3,4-ethylenedioxythiophene)-polystyrenesulfonate (PEDOT:PSS) polymer. Further, we follow a layer-by-layer (LBL) deposition procedure to produce up to 9-layer pairs of PSI and PEDOT:PSS with highly reproducible layer thicknesses as well as distinct changes in surface composition. When tested in an electrochemical cell employing ubiquinone-0 as a mediator, the photocurrent performance of the LBL films increased linearly by 83 ± 6 nA/cm 2 per PSI layer up to 6-layer pairs. The 6-layer pair samples yielded a photocurrent of 414 ± 13 nA/cm 2 , after which the achieved photocurrent diminished with additional layer pairs. The turnover number (TN) of the PSI-PEDOT:PSS LBL assemblies also greatly exceeds that of drop-casted PSI multilayer films, highlighting that the rate of electron collection is improved through the systematic deposition of the protein complexes and conducting polymer. The capability to deposit high loadings of PSI between PEDOT:PSS layers, while retaining connection to the underlying electrode, shows the value in using LBL assembly to produce PSI and PEDOT:PSS bioelectrodes for photoelectrochemical energy harvesting applications.

We report the preparation of pH-responsive, ester/carboxylic acid random copolymer films via simple modification of poly(norbornene diacyl chloride) (pNBDAC), prepared via surface-initiated ring-opening metathesis polymerization, with mixtures of water and ethanol to form carboxylic acid and ethyl ester side groups. The pNBDAC film serves as a compositionally versatile platform to controllably obtain copolymers with multiple functionalities. In modifying the pNBDAC to form the copolymer film, ethanol exhibits a significantly higher reactivity with acyl chloride groups within the film than does water. The magnitude and range of the pH-responsive performance are highly dependent on the carboxylic acid content in the copolymer films, which demonstrates the effect of film hydrophilicity on the pH-responsive switching of ionic barrier properties. The resistance of the film against ion transfer can be decreased by a factor of 10 4 through pH change, demonstrating pH-induced switching from hydrophobic and insulating to swollen and ion-permeable films. The interactions of the copolymer films with water at different pH values were also explored. When the copolymer contains 34% carboxylic acids, a 4× greater film thickness is obtained in high pH solution than in low pH solution due to ionically driven water swelling. The reversibility of the pH-responsive performance of these copolymer films is high based on measurements using quartz crystal microbalance with dissipation (QCM-D).

The photosynthetic protein complex, photosystem I (PSI), can be photoexcited with a quantum efficiency approaching unity and can be integrated into solar energy conversion devices as the photoactive electrode. The incorporation of PSI into conducting polymer frameworks allows for improved conductivity and orientational control in the photoactive layer. Polyviologens are a unique class of organic polycationic polymers that can rapidly accept electrons from a primary donor such as photoexcited PSI and subsequently can donate them to a secondary acceptor. Monomeric viologens, such as methyl viologen, have been widely used as diffusible mediators in wet PSI-based photoelectrochemical cells on the basis of their suitable redox potentials for accepting electrons. Polyviologens possess similar electronic properties to their monomers with the added advantage that they can shuttle electrons in the solid state. Depositing polyviologen directly onto a film of PSI protein results in significant photocurrent enhancement, which confirms its role as an electron-transport material. The polymer film not only improves the photocurrent by aiding the electron transfer but also helps preserve the protein film underneath. The composite polymer-PSI assembly enhances the charge-shuttling processes from individual protein molecules within the PSI multilayer, greatly reducing charge-transfer resistances. The resulting PSI-based solid-state platform demonstrates a much higher photocurrent than the corresponding photoelectrochemical cell built using a similar architecture.

Surface-attached polydicyclopentadiene (pDCPD) films were prepared on gold and silicon substrates via surface-initiated ring-opening metathesis polymerization (SI-ROMP) of dicyclopentadiene (DCPD). The films were grown utilizing monomer in both the vapor phase and the solution phase with the former process exhibiting rapid kinetics, producing ∼400-nm-thick pDCPD films in less than 1 min of polymerization. No significant differences in thickness were observed for films grown from monomer in the vapor phase with the different isomers (exo and endo) of DCPD. Decane was used as an inert additive to control the concentration of DCPD monomer in the vapor phase enabling the preparation of pDCPD films with thickness ranging from tens of nanometers to hundreds of nanometers. The thickness of pDCPD films polymerized using monomer in the vapor phase was enhanced by the presence of a rinse solvent on the surface of the ROMP-active gold substrates. The choice of ROMP catalyst was found to be an important consideration when SI-ROMP was conducted on different substrates. Electrochemical impedance spectroscopy was used to reveal that the films provide effective barriers to the diffusion of aqueous ions in excess of 1 × 10 6 Ω·cm 2 . The mechanical properties of the surface-tethered pDCPD films were quantified with AFM PeakForce quantitative nanomechanical mapping (QNM) with a measured reduced Young's modulus (E r ) of 15 GPa. The measured E r was greater than that of a non-cross-linked surface-tethered polymer, pNB, indicating that the pDCPD films are stiffer.

The interface between photoactive biological materials with two distinct semiconducting electrodes is challenging both to develop and analyze. Building off of our previous work using films of photosystem I (PSI) on p-doped silicon, we have deposited a crystalline zinc oxide (ZnO) anode using confined-plume chemical deposition (CPCD). We demonstrate the ability of CPCD to deposit crystalline ZnO without damage to the PSI biomaterial. Using electrochemical techniques, we were able to probe this complex semiconductor-biological interface. Finally, as a proof of concept, a solid-state photovoltaic device consisting of p-doped silicon, PSI, ZnO, and ITO was constructed and evaluated.

Over the course of a few billion years, nature has developed extraordinary nanomaterials for the efficient conversion of solar energy into chemical energy. One of these materials, photosystem I (PSI), functions as a photodiode capable of generating a charge separation with nearly perfect quantum efficiency. Because of the favorable properties and natural abundance of PSI, researchers around the world have begun to study how this protein complex can be integrated into modern solar energy conversion devices. This feature article describes some of the recent materials and methods that have led to dramatic improvements (over several orders of magnitude) in the photocurrents and photovoltages of biohybrid electrodes based on PSI, with an emphasis on the research activities in our laboratory.

Photosystem I (PSI) is a photoactive electron-transport protein found in plants that participates in the process of photosynthesis. Because of PSI's abundance in nature and its efficiency with charge transfer and separation, there is a great interest in applying the protein in photoactive electrodes. Here, we developed a completely organic, transparent, conductive electrode using reduced graphene oxide (RGO) on which a multilayer of PSI could be deposited. The resulting photoactive electrode demonstrated current densities comparable to that of a gold electrode modified with a multilayer film of PSI and significantly higher than that of a graphene electrode modified with a monolayer film of PSI. The relatively large photocurrents produced by integrating PSI with RGO and using an opaque, organic mediator can be applied to the facile production of more economic solar energy conversion devices.

This article reports the enhanced rate of the surface-initiated polymerization (SIP) of 5-(perfluoro-n-alkyl)norbornenes (NBFn) by combining two SIP techniques, namely surface-initiated atom-transfer polymerization (SI-ATRP) to grow a macroinitiator and surface-initiated ring-opening metathesis polymerization (SI-ROMP) to produce the final coating. This polymerization approach promotes the rapid growth of dense partially fluorinated coatings that are highly hydrophobic and oleophobic and yield thicknesses from 4-12 μm. Specifically, the growth rate and the limiting thickness of pNBFn with different side chain lengths (n = 4, 6, 8, and 10) at various monomer concentrations and temperatures are evaluated through two approaches: growing the polymer from an initiator-terminated monolayer (control) or from a modified poly(2-hydroxyethyl methacrylate) (PHEMA) macroinitiator. X-ray photoelectron spectroscopy (XPS) analysis shows that 38% of the hydroxyl termini in the macroinitiator react with a norbornenyl diacid chloride (NBDAC) molecule, and 7% of such anchored norbornenyl groups react with a catalyst molecule. The kinetic data have been modeled to determine the propagation velocity and the termination rate constant. The PHEMA macroinitiator provides thicker films and faster growth as compared to the monolayer, achieving a 12 μm thick coating of pNBF8 in 15 min. Increasing the monomer side chain length, n, from 4 to 10 improves the growth rate and the limiting polymer thickness. Performing the polymerization process at higher temperature increases the growth rate and the limiting thickness as evidenced by an increase in the film growth rate constant. Arrhenius plots show that the reactions involved in the macroinitiation process exhibit lower activation energies than those formed from a monolayer. Electrochemical impedance spectroscopy reveals that the films exhibit resistance against ion transport in excess of 1 × 10(10) Ω·cm(2).

We report the fabrication of a hybrid light-harvesting electrode consisting of photosystem I (PSI) proteins extracted from spinach and adsorbed as a monolayer onto electrically contacted, large-area graphene. The transparency of graphene supports the choice of an opaque mediator at elevated concentrations. For example, we report a photocurrent of 550 nA/cm(2) from a monolayer of PSI on graphene in the presence of 20 mM methylene blue, which yields an opaque blue solution. The PSI-modified graphene electrode has a total thickness of less than 10 nm and demonstrates photoactivity that is an order of magnitude larger than that for unmodified graphene, establishing the feasibility of conjoining these nanomaterials as potential constructs in next-generation photovoltaic devices.

Photosystem I (PSI) is a membrane protein complex that generates photoinduced electrons and transfers them across the thylakoid membrane during photosynthesis. The PSI complex, separated from spinach leaves, was spread onto the air-water interface as a monolayer and transferred onto a gold electrode surface that was precoated with a self-assembled monolayer (SAM). The electrochemical properties of the transferred PSI monolayer, including cyclic voltammetry and photoinduced chronoamperometry, were measured. The results showed that PSI retained its bioactivity after the manipulation. Its capability of converting photoenergy into electrical potential was demonstrated by its reducing an electron acceptor, dichloroindophenol (DCIP), and by oxidizing an electron donor, sodium ascorbate (ASC). We have shown that the protein has two possible orientations at the water interface. The orientation distribution was determined by comparing the controlled reductive and oxidative photocurrents generated from Langmuir-Blodgett and Langmuir-Schaefer monolayers.

Because of small surface area to volume ratios nanoscale devices can exhibit dominant surface forces that can quickly degrade unlubricated contacting surfaces. While fluorinated materials have been widely used as lubricants, because of their low critical surface tension and high thermal and mechanical stability, fluorinated monolayer coatings, which are suitable for lubricating nanoscale devices, are less effective as lubricants. Although fluorinated monolayers are more stable than their hydrocarbon counterparts against elevated temperature and humidity, they are known to exhibit higher frictional forces. To overcome this issue, here we study mixed monolayers composed of both hydrocarbon and fluorocarbon chains. Hydrocarbon-based monolayers have been widely studied and shown to improve frictional properties and device life. To investigate the frictional behavior of mixed fluorocarbon/hydrocarbon monolayers, molecular dynamics simulations of pure hydrogenated and fluorinated chains and mixed fluorinated/hydrogenated chains on silica surfaces have been performed. The adhesion and friction between the nanoconfined monolayers as a function of normal load, chain length, and chemical composition of the monolayer coating have been investigated, and mixed fluorocarbon/hydrocarbon monolayers found to outperform both pure fluorocarbon and pure hydrocarbon monolayers. Surface coverage was found to have a significant effect on the performance of all systems studied with higher surface coverage resulting in lower frictional forces. The simulations also show that when the hydrocarbon chains in the monolayer are longer than the fluorocarbon chains, a liquidlike layer is formed by the longer hydrocarbon chains that protrudes above the shorter fluorocarbon chains and aids in friction reduction. A frictional load dependence is also seen in these mixed monolayer systems because of repulsive interactions between the fluorocarbon base layer and the hydrocarbon liquidlike layer. A chain length difference of eight carbons between the base layer and the liquidlike layer was found to provide the lowest friction, while both a larger (because of increased entanglement) and a smaller (insufficient atoms between the contacting base layers to form a liquidlike layer) chain length difference increased friction.

Using the abundance of available electrons generated by immobilized multilayers of the photoactive protein complex Photosystem I (PSI), we have photoreduced platinum particles that are catalytically active for the H(2)/H(+) redox couple. The resulting platinized PSI films were optimized using electrochemical measurements and then characterized using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and scanning electrochemical microscopy (SECM). These results demonstrate a novel method for generating immobilized platinum catalysts that are readily available on the surface of a photoactive PSI multilayer.

We report the frictional performance and long-term tribological stability of various alkyl silane monolayer films on silicon by using pin-on-disk tribometry at ambient conditions. We show that the durability of monolayers derived from n-alkyltrichlorosilanes on silicon increases exponentially with the chain length of the silane precursor, which we relate to the cohesive energy of these monolayers through molecular dynamics simulations. X-ray photoelectron spectroscopy (XPS) was used to show that tribological damage consisted of the loss of molecular components that could be partially replaced upon exposure to a solution containing perfluorinated silane precursors. For monolayers derived from n-octadecyltrichlorosilane, a critical load was identified to be approximately 250 mN (200 MPa), above which failure of films occurred within 100 cycles of testing. Monolayers with hydroxyl surfaces exhibited reduced stabilities due to stronger tip-surface interactions. Monolayers with the capability for cross-linking exhibited much greater stabilities than monolayers where cross-linking was limited or prevented. Collectively, these results demonstrate that the mechanical durability of monolayers when subjected to a tribological load is greatly enhanced by maximizing dispersional interactions and cross-linking and minimizing tip-surface interactions.

Superhydrophobic polymethylene (PM) films provide remarkable protection against the transport of aqueous redox probes as a result of entrapped air at the water/polymer interface. The wetting properties and the topography for a set of superhydrophobic (SH) and nonsuperhydrophobic (NSH) PM films were established to compare their interfacial behavior using electrochemical impedance spectroscopy (EIS). EIS results show that SH PM films exhibit resistances against ion transfer that are approximately 3 orders of magnitude higher than those of NSH PM films. Rationalization of these results in the context of the Helmholtz theory reveals that the imaginary impedance or inverse capacitance of SH PM films exhibits positive deviations from that predicted by Helmholtz theory for smooth PM films. Here, we model the capacitance behavior of a SH film as a PM/air composite that acts as a circuit of capacitors. The resulting mathematical model of this analysis enables correlation of the effective dielectric properties of the film (d(effective), epsilon(effective)) to measurable properties such as thickness (d(film)) and the dielectric constant (epsilon(PM)) of the PM film. Finally, a sensitivity analysis shows that the limited contact area between the aqueous solution and PM in SH films is the primary reason for the enhancement in the barrier properties of the film.

The ability to chemically wire ionomer films to electrode surfaces can promote transport near interfaces and impact a host of energy-related applications. Here, we demonstrate proof-of-concept principles for the surface-initiated ring-opening metathesis polymerization (SI-ROMP) of norbornene (NB), 5-butylnorbornene (NBH4), and 5-perfluorobutylnorbornene (NBF4) from Pt-modified gold substrates and the subsequent sulfonation of olefins along the polymer backbones to produce ultrathin sulfonated polymer films. Prior to sulfonation, the films are hydrophobic and exhibit large barriers against ion transport, but sulfonation dramatically reduces the resistance of the films by providing pathways for proton diffusion. Sulfonated films derived from NBF4 and NBH4 yield more anodic potentials for oxygen reduction than those derived from NB or unfunctionalized electrodes. These improvements are consistent with hydrophobic structuring by the fluorocarbon or hydrocarbon side groups to minimize interfacial flooding and generate pathways for enhanced O(2) permeation near the interface. Importantly, we demonstrate that the sulfonated polymer chains remain anchored to the surface during voltammetry for oxygen reduction whereas short-chain thiolates that do not tether polymer are removed from the substrate. This approach, which we extend to unmodified gold electrodes at neutral pH, presents a method of cleaning the ionomer/electrode interface to remove molecular components that may hamper the performance of the electrode.

This Article presents a quantitative comparison of the frictional performance for monolayers derived from n-alkanethiolates on gold and n-alkyl trichlorosilanes on silicon. Monolayers were characterized by pin-on-disk tribometry, contact angle analysis, ellipsometry, and electrochemical impedance spectroscopy (EIS). Pin-on-disk microtribometry provided frictional analysis at applied normal loads from 10 to 1000 mN at a speed of 0.1 mm/s. At low loads (10 mN), methyl-terminated n-alkanethiolate self-assembled monolayers (SAMs) exhibited a 3-fold improvement in coefficient of friction over SAMs with hydroxyl- or carboxylic-acid-terminated surfaces. For monolayers prepared from both n-alkanethiols on gold and n-alkyl trichlorosilanes on silicon, a critical chain length of at least eight carbons is required for beneficial tribological performance at an applied load of 9.8 mN. Evidence for disruption of chemisorbed alkanethiolate SAMs with chain lengths n

The effect of 1-n-butyl-3-methylimidazolium nitrate ionic liquid (IL) on the shear dynamics and tribological properties of contacting ordered alkylsilane self-assembled monolayers (SAM) on SiO(2) surfaces was studied using molecular dynamics simulation. Use of the IL as a lubricant was found to reduce the friction between the contacting monolayers in the studied range of applied loads. At low applied loads, complex behavior in the dependency of the frictional force on the normal load in both lubricated and dry monolayers is observed and is shown to be due to the rearrangement of the SAM chains under shear. In contrast, this dependency was found to be linear at high normal loads. The simulations also indicate that the ordering of the SAM chains may be disrupted by penetrating lubricant molecules, suggesting that the IL could incorporate into a damaged area of the SAM coating and restore tribological properties. To our knowledge, this is the first simulation study of the effect of an IL lubricant on the frictional dynamics of SAMs.

Photosystem I (PSI) has drawn widespread interest for use in biomimetically inspired energy conversion devices upon extracting it from plants or cyanobacteria and assembling it at surfaces. Here, we demonstrate that a critically dense monolayer of spinach-derived PSI must be formed on an electrode surface to achieve optimal photocurrents, and we introduce a new method for preparing these dense PSI monolayers that reduces the time required for assembly by approximately 80-fold in comparison to that for adsorption from solution. This method consists of applying a vacuum above the aqueous PSI solution during assembly to concentrate PSI and precipitate it into a thick layer onto the surface of various self-assembled monolayers or directly onto the electrode surface. Rinsing with water yields a dense monolayer of PSI that draws approximately 100 nA/cm2 of light-induced current from the gold electrode in the presence of appropriate mediators.

We report the surface-initiated growth of poly(alkylnorbornene) films via ring-opening metathesis polymerization (ROMP). The films are grown by exposure of a vinyl-terminated self-assembled monolayer (SAM) on gold to Grubbs first-generation catalyst and the subsequent exposure to an alkylnorbornene monomer. We investigate the influence of alkyl side chains on the structure, barrier, surface properties, and the growth kinetics of surface-initiated ROMP-type poly(norbornene) films. Rate constants for film growth are estimated for the comparison of monomer reactivity. The rate constant for film growth decreases by 3 orders of magnitude from norbornene to decylnorbornene, indicating a strong effect of chain length on initiation and/or propagation rates. Reflectance-absorption infrared spectroscopy is used to show the molecular level packing within the poly(alkylnorbornene) films is disrupted by the alkyl side chains. Tapping-mode atomic force microscopy is used to show that norbornene, butylnorbornene, and hexylnorbornene polymerize from the surface to form dense coatings, whereas decylnorbornene polymerizes to form isolated polymer clusters. The methyl terminus of the alkyl side chains increases the hydrophobicity of the poly(alkylnorbornene) films (thetaA(H2O) = 109-114 degrees) beyond that of a typical poly(norbornene) film (thetaA(H2O) approximately 106 degrees). The additional hydrophobicity throughout the film correlates with superior resistances against redox probes (Rf approximately 105 Omega.cm2) for poly(hexylnorbornene) when compared to polynorbornene (Rf approximately 104 Omega.cm2). The resistance of the poly(decylnorbornene) film (Rf approximately 102 Omega.cm2) is consistent with its nonuniform, cluster-like morphology.

We report the formation of self-assembled monolayers (SAMs) onto gold substrates by exposure to lithium dialkyldithiocarbamate salts [(Li+(R2DTC-), where R = n-propyl, n-butyl, n-octyl, n-decyl, n-dodecyl, or n-octadecyl] in ethanol or methylene chloride. The crystallinity and composition of the monolayers were assessed by polarized modulation infrared reflection absorption spectroscopy (PM-IRRAS), wettability was characterized by contact angles of water and hexadecane, thickness was measured by spectroscopic ellipsometry, and barrier properties determined by electrochemical impedance spectroscopy. While the shorter R2DTC-s formed monolayers with liquid-like packing, monolayers prepared from the longest R2DTC- (where R = n-octadecyl) exhibit similar thickness, crystallinity, wettability, and capacitance as monolayers prepared from n-octadecanethiol. The hydrocarbon chains within the monolayers prepared from (C18)2DTC- are less canted on average than those prepared from n-octadecanethiol. Nonetheless, the (C18)2DTC- SAM exhibits an order of magnitude lower resistance against the penetration of redox probes, which is attributed to a higher density of pinhole defect sites.

We report a method to immobilize thiol-containing ligands onto self-assembled monolayers (SAMs) of alkanethiolates presenting chloracetylated hexa(ethylene glycol) groups. The chloroacetyl groups react with thiols under mild basic conditions, enabling the stable immobilization of biologically active ligands in a well-defined orientation. These SAMs on gold are well suited for studies of biospecific interactions of immobilized ligands with proteins and cells. As a demonstration, we functionalized these SAMs with thiol-containing derivatives of biotin and benzene sulfonamide and observed the specific binding of neutravidin and carbonic anhydrase, respectively. We also used this method to generate mixed SAMs presenting the Arg-Gly-Asp (RGD) peptide sequence and demonstrated the integrin-mediated adhesion of fibroblast cells to these SAMs. This approach would allow the immobilization of proteins and other sensitive biomolecules and ligands for a wide variety of applications in biotechnology.

We have developed a process to incorporate an integral membrane protein, Photosystem I (PSI), into an organic thin film at an electrode surface and thereby insulate the protein complex on the surface while mimicking its natural environment. The PSI complex, which is primarily more hydrophobic on the exterior than interior, is hydrophobically confined in vivo within the thylakoid membrane. To mimic the thylakoid membrane and entrap PSI on an electrode, we have designed a series of steps using a thin self-assembled monolayer (SAM) to adsorb and orient PSI followed by exposures to longer-chained methyl-terminated alkanethiols that place exchange with components of the original SAM in the interprotein domains. In this process, PSI is first adsorbed onto a HOC(6)S/Au substrate through a short exposure to a dilute solution of the protein to achieve a protein coverage of approximately 25%. The PSI/HOC(6)S/Au substrate is then placed into a solution containing one of various longer-chained alkanethiols including C(22)SH or C(18)OC(19)SH. Changes in thickness, interfacial capacitance, infrared spectra, and surface wettability were used to assess the extent of backfilling by the long-chained thiols. The coverage of the protein layer and the solvent used for backfilling affected the rate and quality of the SAM formed in the interprotein regions. After exposure of the PSI layer to solvents containing alkanethiols, there was only minor loss of protein on the surface and no real change in protein secondary structure as evidenced by reflectance absorption infrared spectroscopy.

We report the preparation of loosely packed hydroxyl-terminated self-assembled monolayers (SAMs) on gold by the adsorption of bis(11,11'-dithioundecyl)perfluoroheptanoate and base-mediated cleavage of the fluorocarbon terminal group. As shown through complementary characterization methods, the partially fluorinated SAM exhibits a structure in which the outer surface contains mostly -CF(3) groups, the fluorocarbon groups are slightly canted on average, and the hydrocarbon chains underneath are in a fluidlike state. Upon cleavage of the fluorocarbon group, the hydroxyl-terminated alkyl chains relax into an increasingly canted, fluidlike state. The resulting monolayer packing exposes both methylene and hydroxyl functionalities, yielding an intermediate surface energy (theta(a)(H(2)O) approximately 68 degrees ). As compared to a densely packed hydroxyl-terminated SAM prepared from bis(11-hydroxyundecyl)disulfide, the cleaved films are thinner because of the greater average chain cant and exhibit a approximately 50% higher capacitance and a factor of 5 lower charge-transfer resistance. The addition of THF to the electrolyte solution as a cosolvent intercalates into the loosely packed SAM to double the charge-transfer resistance and increase the capacitance by approximately 20% but does not affect the capacitance of the densely packed SAM. The loosely packed SAM is also more easily exchanged upon exposure to a solution of n-docosanethiol.

We report the first directed adsorption of Photosystem I (PSI) on patterned surfaces containing discrete regions of methyl- and hydroxyl-terminated self-assembled monolayers (SAMs) on gold. SAM and PSI patterns are characterized by scanning electrochemical microscopy (SECM). The insulating protein complex layer blocks the electron transfer of the SECM mediator, thereby reducing the electrochemical current significantly. Uniformly and densely packed adsorbed protein layers are observed with SECM. Pattern images correlate with our previous studies where we showed that low-energy surfaces (e.g., CH3-terminated) inhibit PSI adsorption in the presence of Triton X-100, whereas high-energy surfaces (e.g., OH-terminated) enable adsorption. Therefore, a SAM pattern with alternating methyl and hydroxyl surface regions allows PSI adsorption only on the hydroxyl surface, and this is demonstrated in the resulting SECM images.

We have used self-assembled monolayers (SAMs) prepared from omega-terminated alkanethiols on gold to generate model surfaces and examine the effect of surface composition on the adsorption of Photosystem I (PSI), stabilized in aqueous solution by Triton X-100. Triton-stabilized PSI adsorbs to high-energy surfaces prepared from HO- and HO2C-terminated alkanethiols but does not adsorb to low-energy surfaces. The inhibition of PSI adsorption at low-energy surfaces is consistent with the presence of a layer of Triton X-100 that adsorbs atop the hydrophobic SAM and presents a protein-resistant poly(ethylene glycol) (PEG) surface. While the presence of the PEG surface prevents the adsorption of PSI, the displacement of the inhibiting layer of Triton X-100 by dodecanol, a more active surfactant, greatly enhances the adsorption of PSI. This inhibiting effect by Triton X-100 can be extended to other protein systems such as bovine serum albumin.