Search

Large-bandwidth pulses produced by cutting-edge X-ray free-electron lasers (FELs) are of great importance in research fields like material science and biology. In this paper, a new method to generate high-power ultrashort FEL pulses with tunable spectral bandwidth with spectral coherence using a dielectric-lined waveguide without interfering operation of linacs is proposed. By exploiting the passive and dephasingless wakefield at terahertz frequency excited by the beam, stable energy modulation can be achieved in the electron beam and large-bandwidth high-intensity soft X-ray radiation can be generated. Three-dimensional start-to-end simulations have been carried out and the results show that coherent radiation pulses with duration of a few femtoseconds and bandwidths ranging from 1.01% to 2.16% can be achieved by changing the undulator taper profile. [ABSTRACT FROM AUTHOR]

With fast advances in enhancing the focusing/imaging resolution of Fresnel zone plate lenses toward sub-10 nm, low diffraction efficiency in connection with their rectangular zone shape still remains a big issue in both soft and hard X-ray microscopy. In hard X-ray optics, encouraging progress has recently been reported in our earlier attempts of high focusing efficiency by 3D kinoform shaped metallic zone plates, formed by greyscale electron beam lithography. This paper addresses our efforts towards high focusing/imaging efficiency by developing a novel dielectric kinoform zone plate lens for soft X-rays. The effects of the zone materials and zone shapes on the focusing/imaging quality were first theoretically investigated by a modified thin-grating-approximation method, revealing superior efficiencies of dielectric kinoform zone plates over rectangular ones in metals. Optical characterizations of replicated dielectric kinoform zone plates by greyscale electron beam lithography demonstrate a focusing efficiency of 15.5% with a resolution of 110 nm in the water window of X-rays. Apart from high efficiency, the novel kinoform zone plate lenses developed in this work exhibit significant advantages over conventional zone plates, i.e. simplified process, low cost and no need for a beamstop. [ABSTRACT FROM AUTHOR]

MAX IV is a fourth‐generation, or diffraction‐limited, synchrotron light source with a number of state‐of‐the‐art beamlines. The performance of a beamline is, to a high degree, set by the energy resolution it can achieve, which in turn is governed to a large extent by the monochromator. During the design phase of a monochromator, the mechanical requirements must be fully understood and met with margin. During commissioning, the performance must be verified and optimized. In this paper, six soft X‐ray monochromators at MAX IV beamlines (Bloch, Veritas, HIPPIE, SPECIES, FinEstBeAMS and SoftiMAX) are examined with a focus on their resolving power, energy range and the time required to change measurement range, as those parameters are dependent on each other. The monochromators have a modern commercial design, planned and developed in close collaboration with the vendors. This paper aims to present the current status of the commissioning at MAX IV with emphasis on elucidating the mechanical limitations on the performance of the monochromators. It contains analysis of the outcome and our approach to achieve fast and high‐resolution monochromators. [ABSTRACT FROM AUTHOR]

The Shanghai Soft X-ray Free-Electron Laser (SXFEL) is the first X-ray freeelectron laser facility in China. The SASE beamline, which consists of a pinkbeam branch and a mono-beam branch, is one of the two beamlines in the Phase-I construction. The pink-beam branch opened for users in 2023 after successful first-round beamline commissioning. In this paper, the design of the beamline is presented and the performance of the pink-beam branch is reported. The measured energy-resolving power of the online spectrometer is over 6000 @ 400 eV. The focusing spot size of the pink beam is less than 3 μm in both the horizontal and vertical at the endstation. [ABSTRACT FROM AUTHOR]

In this paper the design of the free‐electron laser (FEL) in the SXL (Soft X‐ray Laser) project at the MAX IV Laboratory is presented. The target performance parameters originate in a science case put forward by Swedish users and the SXL FEL is foreseen to be driven by the existing MAX IV 3 GeV linac. The SXL project is planned to be realized in different stages and in this paper the focus is on Phase 1, where the basic operation mode for the FEL will be SASE (self‐amplified spontaneous emission), with an emphasis on short pulses. Simulation results for two linac bunches (high and low charge) with different pulse duration are illustrated, as well as the performance for two‐color/two‐pulses mode and power enhancement through tapering. Besides standard SASE and optical klystron configurations, the FEL setup is also tailored to allow for advanced seeding schemes operations. Finally possible upgrades that will be implemented in a second phase of the project are discussed. [ABSTRACT FROM AUTHOR]

This article presents a demonstration of the improved performance of an X‐ray free‐electron laser (FEL) using the optical klystron mechanism and helical undulator configuration, in comparison with the common planar undulator configuration without optical klystron. The demonstration was carried out at Athos, the soft X‐ray beamline of SwissFEL. Athos has variable‐polarization undulators, and small magnetic chicanes placed between every two undulators to fully exploit the optical klystron. It was found that, for wavelengths of 1.24 nm and 3.10 nm, the required length to achieve FEL saturation is reduced by about 35% when using both the optical klystron and helical undulators, with each effect accounting for about half of the improvement. Moreover, it is shown that a helical undulator configuration provides a 20% to 50% higher pulse energy than planar undulators. This work represents an important step towards more compact and high‐power FELs, rendering this key technology more efficient, affordable and accessible to the scientific community. [ABSTRACT FROM AUTHOR]

Calculations and measurements of polarization-dependent soft X-ray scattering intensity are presented during a magnetic hysteresis cycle. It is confirmed that the dependence of the intensity on the magnetic moment can be linear, quadratic or a combination of both, depending on the polarization of the incident X-ray beam and the direction of the magnetic moment. With a linearly polarized beam, the scattered intensity will have a purely quadratic dependence on the magnetic moment when the magnetic moment is parallel to the scattering plane. However, with the magnetic moment perpendicular to the scattering plane, there is also a linear component. This means that, when measuring the hysteresis with linear polarization during a hysteresis cycle, the intensity will be an even function of the applied field when the change in the magnetic moment (and field) is confined within the scattering plane but becomes more complicated when the magnetic moment is out of the scattering plane. Furthermore, with circular polarization, the dependence of the scattered intensity on the moment is a combination of linear and quadratic. With the moment parallel to the scattering plane, the linear component changes with the helicity of the incident beam. Surprisingly, in stark contrast to absorption studies, even when the magnetic moment is perpendicular to the scattering plane there is still a dependence on the moment with a linear component. This linear component is completely independent of the helicity of the beam, meaning that the hysteresis loops will not be inverted with helicity. [ABSTRACT FROM AUTHOR]

Synchrotron light sources can provide the required spatial coherence, stability and control to support the development of advanced lithography at the extreme ultraviolet and soft X-ray wavelengths that are relevant to current and future fabricating technologies. Here an evaluation of the optical performance of the soft X-ray (SXR) beamline of the Australian Synchrotron (AS) and its suitability for developing interference lithography using radiation in the 91.8 eV (13.5 nm) to 300 eV (4.13 nm) range are presented. A comprehensive physical optics model of the APPLE-II undulator source and SXR beamline was constructed to simulate the properties of the illumination at the proposed location of a photomask, as a function of photon energy, collimation and monochromator parameters. The model is validated using a combination of experimental measurements of the photon intensity distribution of the undulator harmonics. It is shown that the undulator harmonics intensity ratio can be accurately measured using an imaging detector and controlled using beamline optics. Finally, the photomask geometric constraints and achievable performance for the limiting case of fully spatially coherent illumination are evaluated. [ABSTRACT FROM AUTHOR]

FlexPES is a soft X-ray beamline on the 1.5 GeV storage ring at MAX IV Laboratory, Sweden, providing horizontally polarized radiation in the 40-1500 eV photon energy range and specializing in high-resolution photoelectron spectroscopy, fast X-ray absorption spectroscopy and electron-ion/ion-ion coincidence techniques. The beamline is split into two branches currently serving three endstations, with a possibility of adding a fourth station at a free port. The refocusing optics provides two focal points on each branch, and enables either focused or defocused beam on the sample. The endstation EA01 at branch A (Surface and Materials Science) is dedicated to surface- and materials-science experiments on solid samples at ultra-high vacuum. It is well suited not only to all flavours of photoelectron spectroscopy but also to fast (down to sub-minute) high-resolution X-ray absorption measurements with various detectors. Branch B (Low-Density Matter Science) has the possibility to study gas-phase/liquid samples at elevated pressures. The first endstation of this branch, EB01, is a mobile setup for various ion-ion and electron-ion coincidence techniques. It houses a versatile reaction microscope, which can be used for experiments during single-bunch or multi-bunch delivery. The second endstation, EB02, is based on a rotatable chamber with an electron spectrometer for photoelectron spectroscopy studies on primarily volatile targets, and a number of peripheral setups for sample delivery, such as molecular/cluster beams, metal/semiconductor nanoparticle beams and liquid jets. This station can also be used for non-UHV photoemission studies on solid samples. In this paper, the optical layout and the present performance of the beamline and all its endstations are reported. [ABSTRACT FROM AUTHOR]

A numerical study of the effect of betatron oscillations on the second harmonic generation in free‐electron lasers (FELs) is presented. Analytical expressions for the effective coupling strength factors are derived that clearly distinguish all contributions in subharmonics and each polarization of the radiation. A three‐dimensional time‐dependent numerical FEL code that takes into account the main FEL effects and the individual contribution of each electron to the second harmonic generation is presented. Also, the X‐ and Y‐polarizations of the second harmonic are analyzed. The second harmonic was detected in experiments at the Advanced Photon Source (APS) Low Energy Undulator Test Line (LEUTL) and Linac Coherent Light Source (LCLS) in the soft X‐ray regime. The approach presented in the article can be useful for a comprehensive study and diagnostics of XFELs. In the paper, the LCLS and Pohang Accelerator Laboratory X‐ray Free‐Electron Laser (PAL‐XFEL) experiments are modeled. The simulation results are in a good agreement with the experimental data. [ABSTRACT FROM AUTHOR]

X‐ray absorption is a sensitive and versatile tool for chemical speciation. However, when high doses are used, the absorbed energy can change the composition, amount and structure of the native material, thereby changing the aspects of the absorption process on which speciation is based. How can one calculate the dose when X‐ray irradiation affects the chemistry and changes the amount of the material? This paper presents an assumption‐free approach which can retrieve from the experimental data all dose‐sensitive parameters – absorption coefficients, composition (elemental molecular units), material densities – which can then be used to calculate accurate doses as a function of irradiation. This approach is illustrated using X‐ray damage to a solid film of a perfluorosulfonic acid fluoropolymer in a scanning transmission soft X‐ray microscope. This new approach is compared against existing dose models which calculate the dose by making simplifying assumptions regarding the material quantity, density and chemistry. While the detailed measurements used in this approach go beyond typical methods to experimental analytical X‐ray absorption, they provide a more accurate quantitation of radiation dose, and help to understand mechanisms of radiation damage. [ABSTRACT FROM AUTHOR]

This work investigates the performance of the electrospray aerosol generator at the European X-ray Free Electron Laser (EuXFEL). This generator is, together with an aerodynamic lens stack that transports the particles into the X-ray interaction vacuum chamber, the method of choice to deliver particles for single-particle coherent diffractive imaging (SPI) experiments at the EuXFEL. For these experiments to be successful, it is necessary to achieve high transmission of particles from solution into the vacuum interaction region. Particle transmission is highly dependent on efficient neutralization of the charged aerosol generated by the electrospray mechanism as well as the geometry in the vicinity of the Taylor cone. We report absolute particle transmission values for different neutralizers and geometries while keeping the conditions suitable for SPI experiments. Our findings reveal that a vacuum ultraviolet ionizer demonstrates a transmission efficiency approximately seven times greater than the soft X-ray ionizer used previously. Combined with an optimized orifice size on the counter electrode, we achieve >40% particle transmission from solution into the X-ray interaction region. These findings offer valuable insights for optimizing electrospray aerosol generator configurations and data rates for SPI experiments. [ABSTRACT FROM AUTHOR]

The SPECIES beamline has been transferred to the new 1.5 GeV storage ring at the MAX IV Laboratory. Several improvements have been made to the beamline and its endstations during the transfer. Together the Ambient Pressure X‐ray Photoelectron Spectroscopy and Resonant Inelastic X‐ray Scattering endstations are capable of conducting photoelectron spectroscopy in elevated pressure regimes with enhanced time‐resolution and flux and X‐ray scattering experiments with improved resolution and flux. Both endstations offer a unique capability for experiments at low photon energies in the vacuum ultraviolet and soft X‐ray range. In this paper, the upgrades on the endstations and current performance of the beamline are reported. [ABSTRACT FROM AUTHOR]

In this paper the back‐side‐illuminated Percival 2‐Megapixel (P2M) detector is presented, along with its characterization by means of optical and X‐ray photons. For the first time, the response of the system to soft X‐rays (250 eV to 1 keV) is presented. The main performance parameters of the first detector are measured, assessing the capabilities in terms of noise, dynamic range and single‐photon discrimination capability. Present limitations and coming improvements are discussed. [ABSTRACT FROM AUTHOR]

The impressive progress in the performance of synchrotron radiation sources is nowadays driven by the so‐called 'ultimate storage ring' projects which promise an unprecedented improvement in brightness. Progress on the detector side has not always been at the same pace, especially as far as soft X‐ray 2D detectors are concerned. While the most commonly used detectors are still based on microchannel plates or CCD technology, recent developments of CMOS (complementary metal oxide semiconductor)‐type detectors will play an ever more important role as 2D detectors in the soft X‐ray range. This paper describes the capabilities and performance of a camera equipped with a newly commercialized backside‐illuminated scientific CMOS (sCMOS‐BSI) sensor, integrated in a vacuum environment, for soft X‐ray experiments at synchrotron sources. The 4 Mpixel sensor reaches a frame rate of up to 48 frames s−1 while matching the requirements for X‐ray experiments in terms of high‐intensity linearity (>98%), good spatial homogeneity (<1%), high charge capacity (up to 80 ke−), and low readout noise (down to 2 e− r.m.s.) and dark current (3 e− per second per pixel). Performance evaluations in the soft X‐ray range have been carried out at the METROLOGIE beamline of the SOLEIL synchrotron. The quantum efficiency, spatial resolution (24 line‐pairs mm−1), energy resolution (<100 eV) and radiation damage versus the X‐ray dose (<600 Gy) have been measured in the energy range from 40 to 2000 eV. In order to illustrate the capabilities of this new sCMOS‐BSI sensor, several experiments have been performed at the SEXTANTS and HERMES soft X‐ray beamlines of the SOLEIL synchrotron: acquisition of a coherent diffraction pattern from a pinhole at 186 eV, a scattering experiment from a nanostructured Co/Cu multilayer at 767 eV and ptychographic imaging in transmission at 706 eV. [ABSTRACT FROM AUTHOR]

This paper presents a novel cantilevered liquid‐nitrogen‐cooled silicon mirror design for the first optic in a new soft X‐ray beamline that is being developed as part of the Advanced Light Source Upgrade (ALS‐U) (Lawrence Berkeley National Laboratory, USA). The beamline is optimized for photon energies between 400 and 1400 eV with full polarization control. Calculations indicate that, without correction, this design will achieve a Strehl ratio greater than 0.85 for the entire energy and polarization ranges of the beamline. With a correction achieved by moving the focus 7.5 mm upstream, the minimum Strehl ratio is 0.99. This design is currently the baseline plan for all new ALS‐U insertion device beamlines. [ABSTRACT FROM AUTHOR]

Based on the the third‐order aberration theory of plane‐symmetric optical systems, this paper studies the effect on aberrations of the second‐order accuracy of aperture‐ray coordinates and the extrinsic aberrations of this kind of optical system; their calculation expressions are derived. The resultant aberration expressions are then applied to calculate the aberrations of two design examples of soft X‐ray and vacuum ultraviolet (XUV) optical systems; images are compared with ray‐tracing results using SHADOW software to validate the aberration expressions. The study shows that the accuracy of the aberration expressions is satisfactory. [ABSTRACT FROM AUTHOR]

The characterization of X-ray focal spots is of great significance for the diagnosis and performance optimization of focusing systems. X-ray free-electron lasers (XFELs) are the latest generation of X-ray sources with ultrahigh brilliance, ultrashort pulse duration and nearly full transverse coherence. Because each XFEL pulse is unique and has an ultrahigh peak intensity, it is difficult to characterize its focal spot size individually with full power. Herein, a method for characterizing the spot size at the focus position is proposed based on coherent diffraction imaging. A numerical simulation was conducted to verify the feasibility of the proposed method. The focal spot size of the Coherent Scattering and Imaging endstation at the Shanghai Soft X-ray Free Electron Laser Facility was characterized using the method. The full width at half-maxima of the focal spot intensity and spot size in the horizontal and vertical directions were calculated to be 2.10 ± 0.24 mm and 2.00 ± 0.20 mm, respectively. An ablation imprint on the silicon frame was used to validate the results of the proposed method. [ABSTRACT FROM AUTHOR]

A phase-merging enhanced harmonic generation free-electron laser (FEL) was proposed to increase the harmonic conversion efficiency of seeded FELs and promote the radiation wavelength towards the X-ray spectral region. However, this requires a specially designed transverse gradient undulator (TGU) as the modulator to couple the transverse and longitudinal phase space of the electron beam. In this paper, the generation of the phase-merging effect is explored using the natural field gradient of a normal planar undulator. In this method, a vertical dispersion on the electron beam is introduced and then the dispersed beam travels through a normal modulator in a vertical off-axis orbit where the vertical field gradient is selected properly in terms of the vertical dispersion strength and modulation amplitude. The phase-merging effect will be generated after passing through the dispersive chicane. Theoretical analysis and numerical simulations for a seeded soft X-ray FEL based on parameters of the Shanghai Soft X-ray FEL project are presented. Compared with a TGU modulator, using the natural gradient of a normal planar modulator has the distinct advantage that the gradient can be conveniently tuned in quite a large range by adjusting the beam orbit offset. [ABSTRACT FROM AUTHOR]

The Paul Scherrer Institute is implementing laser-based seeding in the soft X-ray beamline (Athos) of its free-electron laser, SwissFEL, to enhance the temporal and spectral properties of the delivered photon pulses. This technique requires, among other components, two identical modulators for coupling the electron beam with an external laser with a wavelength range between 260 and 1600 nm. The design, magnetic measurements results, alignment, operation and also details of the novel and exotic magnetic configuration of the prototype are described. [ABSTRACT FROM AUTHOR]

Elliptical polarized undulators (EPUs) are broadly used in the soft X‐ray energy range. They have the advantage of providing photons with both varied energy and polarization through adjustments to the value of the gap and/or shift magnet arrays in an undulator. Yet these adjustments may create a disturbance on the stability of the electron beam in a storage ring. To correct such a disturbance, it is necessary to establish a feed‐forward table of key nodes in the gap‐shift‐defined two‐dimensional parameter space. Such a table can only be scanned during machine‐study time. For a free‐walking mode, whereby an undulator is allowed to manoeuvre in the whole gap‐shift space, all the key nodes need to be scanned at the expense of a large amount of machine‐study time. This will greatly delay the employment of a full‐polarization capable undulator (especially circularly polarized). By analyzing data‐collecting patterns of user experiments, this paper defines a reduced set of key nodes in gap‐shift parameter space, with the number of key nodes to be scanned for feed‐forwarding scaled down to one‐third of the original; and introduces a new walking mode for EPUs: confined‐walking mode, whereby the undulator is manoeuvred only within the reduced set of key nodes. Such a mode is firstly realized on the EPUs at the DREAMLINE beamline at Shanghai Synchrotron Radiation Facility (SSRF). Under confined‐walking mode, the undulator movements are stable and there is no obvious disturbance to the electron beam with the feed‐forward system in operation. Successful experiments have been carried out using the circularly polarized light obtained via the new walking mode. This mode is expected to be applied to future EPUs at SSRF with the increasing requirements for various polarization modes. [ABSTRACT FROM AUTHOR]

This report presents testing of a prototype cantilevered liquid-nitrogen-cooled silicon mirror. This mirror was designed to be the first mirror for the new soft X-ray beamlines to be built as part of the Advanced Light Source Upgrade. Test activities focused on fracture, heat transfer, modal response and distortion, and indicated that the mirror functions as intended. [ABSTRACT FROM AUTHOR]

A picosecond pump-probe resonant soft X-ray scattering measurement system has been developed at the Photon Factory storage ring for highly efficient data collection. A high-repetition-rate high-power compact laser system has been installed to improve efficiency via flexible data acquisition to a sub-MHz frequency in time-resolved experiments. Data are acquired by gating the signal of a channel electron multiplier with a pulse-counting mode capable of discriminating single-bunch soft X-ray pulses in the dark gap of the hybrid operation mode in the storage ring. The photoinduced dynamics of magnetic order for multiferroic manganite SmMn2O5 are clearly demonstrated by the detection of transient changes in the resonant soft X-ray scattering intensity around the Mn LIII- and O K-edges. [ABSTRACT FROM AUTHOR]

Soft X-ray monochromators for synchrotron radiation sources have been continuously developed over the years, improving energy resolution and stability. Great effort has been made in improving the surface quality of the optics involved, reaching values permitting diffraction-limited images. Still, one problem has not been solved, nor fully understood, yet: groove placing errors. Nowadays, these are one of the major factors responsible for resolving the power reduction of diffraction-gratings-based X-ray monochromators. Despite decades of use of gratings, there is not yet a universally established method for predicting and simulating the effect of groove placing errors on monochromator performance. This is especially important in the new scenario of high-coherent X-ray sources, i.e. diffraction-limited storage rings and free-electron lasers. To address this problem, in this article an approach based on WISER (Wavefront propagatIon Simulation codE libRary) is presented. WISER is a physical optics simulation package, also available in the user-friendly Orange Synchrotron Radiation Suite - OASYS. Even though it was originally conceived to assess the focusing performance of X-ray mirrors in the presence of height defects, it perfectly simulates the performance of a periodic (or quasi-periodic) structure like a diffraction grating. In this article, the way to use WISER and its application to a specific case, e.g. the design of a monochromator for the upgrade of a beamline at the Advanced Light Source, are shown. A simple rule for estimating how well the grooves are placed on a grating, based on calculation of the Strehl ratio, is also presented. [ABSTRACT FROM AUTHOR]

Monochromators for synchrotron radiation beamlines typically use perfect crystals for the hard X-ray regime and gratings for soft X-rays. There is an intermediate range, typically 1-3 keV (tender X-rays), which common perfect crystals have difficulties covering and gratings have low efficiency, although some less common crystals with high d-spacing could be suitable. To evaluate the suitability of these crystals for a particular beamline, it is useful to evaluate the crystals' performance using tools such as ray-tracing. However, simulations for double-crystal monochromators are only available for the most used crystals such as Si, Ge or diamond. Here, an upgrade of the SHADOW ray-tracing code and complementary tools in the OASYS suite are presented to simulate high dspacing crystals with arbitrary, and sometimes complex, structures such as beryl, YB66, muscovite, etc. Isotropic and anisotropic temperature factors are also considered. The YB66 crystal with 1936 atomic sites in the unit cell is simulated, and its applicability for tender X-ray monochromators is discussed in the context of new low-emittance storage rings. [ABSTRACT FROM AUTHOR]

The use of soft X-rays near the carbon edge of absorption (270-300 eV) greatly enhances studies in various branches of science. However, the choice of reflecting coatings for mirrors operating in free-electron and X-ray free-electron laser (FEL and XFEL) beamlines in this spectral range is not so evident and experimental justifications of the mirror efficiency are rather limited. In the present paper it is demonstrated experimentally that the reflectivity of B4C- and Ni-coated grazing-incidence mirrors is high enough for their operation in FEL or XFEL beamlines near the carbon K-edge of absorption. The minimal reflectivity of both mirrors proves to exceed 80% near the carbon absorption edge at a grazing angle of 0.6°. An in-depth profile of the chemical elements composing the reflecting coatings is reconstructed based on analysis of a set of reflectivity curves measured versus the grazing angle at different photon energies in the soft X-ray spectral region. This allows us to predict correctly the mirror reflectivity at any X-ray energy and any grazing angle. [ABSTRACT FROM AUTHOR]

Boron carbide is a prominent material for high-brilliance synchrotron optics as it remains stable up to very high temperatures. The present study shows a significant change taking place at 550 °C in the buried interface region formed between the Cr adhesive layer and the native oxide layer present on the silicon substrate. An in situ annealing study is carried out at the Indus-1 Reflectivity beamline from room temperature to 550°C (100°C steps). The studied sample is a mirror-like boron carbide thin film of 400 A ° thickness deposited with an adhesive layer of 20 A ° Cr on a silicon substrate. The corresponding changes in the film structure are recorded using angle-dependent soft X-ray reflectivity measurements carried out in the region of the boron K-edge after each annealing temperature. Analyses performed using the Parratt recursive formalism reveal that the top boron carbide layer remains intact but interface reactions take place in the buried Cr-SiO2 region. After 300°C the Cr layer diffuses towards the substrate. At higher temperatures of 500°C and 550 °C the Cr reacts with the native oxide layer and tends to form a low-density compound of chromium oxysilicide (CrSiOx). Depth profiling of Si and Cr distributions obtained from secondary ion mass spectroscopy measurements corroborate the layer model obtained from the soft X-ray reflectivity analyses. Details of the interface reaction taking place near the substrate region of boron carbide/Cr sample are discussed. [ABSTRACT FROM AUTHOR]

The newly constructed time-resolved atomic, molecular and optical science instrument (TMO) is configured to take full advantage of both linear accelerators at SLAC National Accelerator Laboratory, the copper accelerator operating at a repetition rate of 120 Hz providing high per-pulse energy as well as the superconducting accelerator operating at a repetition rate of about 1 MHz providing high average intensity. Both accelerators power a soft X-ray freeelectron laser with the new variable-gap undulator section. With this flexible light source, TMO supports many experimental techniques not previously available at LCLS and will have two X-ray beam focus spots in line. Thereby, TMO supports atomic, molecular and optical, strong-field and nonlinear science and will also host a designated new dynamic reaction microscope with a submicrometer X-ray focus spot. The flexible instrument design is optimized for studying ultrafast electronic and molecular phenomena and can take full advantage of the sub-femtosecond soft X-ray pulse generation program. [ABSTRACT FROM AUTHOR]

The soft X-ray photoelectron momentum microscopy (PMM) experimental station at the UVSOR Synchrotron Facility has been recently upgraded by additionally guiding vacuum ultraviolet (VUV) light in a normal-incidence configuration. PMM offers a very powerful tool for comprehensive electronic structure analyses in real and momentum spaces. In this work, a VUV beam with variable polarization in the normal-incidence geometry was obtained at the same sample position as the soft X-ray beam from BL6U by branching the VUV beamline BL7U. The valence electronic structure of the Au(111) surface was measured using horizontal and vertical linearly polarized (s-polarized) light excitations from BL7U in addition to horizontal linearly polarized (p-polarized) light excitations from BL6U. Such highly symmetric photoemission geometry with normal incidence offers direct access to atomic orbital information via photon polarization-dependent transition-matrix-element analysis. [ABSTRACT FROM AUTHOR]

The beamline optics and endstations at branch B of the Versatile Soft X-ray (VerSoX) beamline B07 at Diamond Light Source are described. B07-B provides medium-flux X-rays in the range 45-2200 eV from a bending magnet source, giving access to local electronic structure for atoms of all elements from Li to Y. It has an endstation for high-throughput X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine-structure (NEXAFS) measurements under ultrahigh-vacuum (UHV) conditions. B07-B has a second endstation dedicated to NEXAFS at pressures from UHV to ambient pressure (1 atm). The combination of these endstations permits studies of a wide range of interfaces and materials. The beamline and endstation designs are discussed in detail, as well as their performance and the commissioning process. [ABSTRACT FROM AUTHOR]

Synchrotron radiation can induce sample damage, whether intended or not. In the case of sensitive samples, such as biological ones, modifications can be significant. To understand and predict the effects due to exposure, it is necessary to know the ionizing radiation dose deposited in the sample. In the case of aqueous samples, deleterious effects are mostly induced by the production of reactive oxygen species via water radiolysis. These species are therefore good indicators of the dose. Here the application of a microfluidic cell specifically optimized for low penetrating soft X‐ray radiation is reported. Sodium benzoate was used as a fluorescent dosimeter thanks to its specific detection of hydroxyl radicals, a radiolytic product of water. Measurements at 1.28 keV led to the determination of a hydroxyl production yield, G(HO.), of 0.025 ± 0.004 µmol J−1. This result is in agreement with the literature and confirms the high linear energy transfer behavior of soft X‐rays. An analysis of the important parameters of the microfluidic dosimetry cell, as well as their influences over dosimetry, is also reported. [ABSTRACT FROM AUTHOR]

The mutual optical intensity (MOI) model is extended to the simulation of the interference pattern produced by extreme ultraviolet lithography with partially coherent light. The partially coherent X‐ray propagation through the BL08U1B beamline at Shanghai Synchrotron Radiation Facility is analysed using the MOI model and SRW (Synchrotron Radiation Workshop) method. The fringe intensity at the exposure area is not uniform but has similar envelope lines to Fresnel diffraction, which is explained by the diffraction from the finite grating modelled as a single aperture. By balancing the slit size and photon stop size, the fringe visibility, photon flux and intensity slope can be optimized. Further analysis shows that the effect of pink light on the aerial images is negligible, whereas the third‐harmonic light should be considered to obtain a balance between high fringe visibility and high flux. Two grating interference exposure experiments were performed in the BL08U1B beamline. The aerial image depth showed that the polymethyl methacrylate photoresist depth was determined by the X‐ray coherence properties. [ABSTRACT FROM AUTHOR]

This paper describes the development of new instrumentation at the Linac Coherent Light Source for conducting THz excitation experiments in an ultra high vacuum environment probed by soft X-ray diffraction. This consists of a cantilevered, fully motorized mirror system which can provide 600 kV cm−1 electric field strengths across the sample and an X-ray detector that can span the full Ewald sphere with in-vacuum motion. The scientific applications motivated by this development, the details of the instrument, and spectra demonstrating the field strengths achieved using this newly developed system are discussed. [ABSTRACT FROM AUTHOR]

The Diffraction and Projection Imaging (DiProI) beamline at FERMI, the Elettra free-electron laser (FEL), hosts a multi-purpose station that has been opened to users since the end of 2012. This paper describes the core capabilities of the station, designed to make use of the unique features of the FERMI-FEL for performing a wide range of static and dynamic scattering experiments. The various schemes for time-resolved experiments, employing both soft X-ray FEL and seed laser IR radiation are presented by using selected recent results. The ongoing upgrade is adding a reflection geometry setup for scattering experiments, expanding the application fields by providing both high lateral and depth resolution. [ABSTRACT FROM AUTHOR]

A scanning soft X‐ray spectromicroscope was recently developed based mainly on the photon‐in/photon‐out measurement scheme for the investigation of local electronic structures on the surfaces and interfaces of advanced materials under conditions ranging from low vacuum to helium atmosphere. The apparatus was installed at the soft X‐ray beamline (BL17SU) at SPring‐8. The characteristic features of the apparatus are described in detail. The feasibility of this spectromicroscope was demonstrated using soft X‐ray undulator radiation. Here, based on these results, element‐specific two‐dimensional mapping and micro‐XAFS (X‐ray absorption fine structure) measurements are reported, as well as the observation of magnetic domain structures from using a reference sample of permalloy micro‐dot patterns fabricated on a silicon substrate, with modest spatial resolution (e.g. ∼500 nm). Then, the X‐ray radiation dose for Nafion® near the fluorine K‐edge is discussed as a typical example of material that is not radiation hardened against a focused X‐ray beam, for near future experiments. [ABSTRACT FROM AUTHOR]

Anaerobic ammonium‐oxidizing (anammox) bacteria play a key role in the global nitrogen cycle and in nitrogenous wastewater treatment. The anammox bacteria ultrastructure is unique and distinctly different from that of other prokaryotic cells. The morphological structure of an organism is related to its function; however, research on the ultrastructure of intact anammox bacteria is lacking. In this study, in situ three‐dimensional nondestructive ultrastructure imaging of a whole anammox cell was performed using synchrotron soft X‐ray tomography (SXT) and the total variation‐based simultaneous algebraic reconstruction technique (TV‐SART). Statistical and quantitative analyses of the intact anammox bacteria were performed. High soft X‐ray absorption composition inside anammoxosome was detected and verified to be relevant to iron‐binding protein. On this basis, the shape adaptation of the anammox bacteria response to iron was explored. [ABSTRACT FROM AUTHOR]

The optical design of a Hettrick–Underwood‐style soft X‐ray spectrometer with Wolter type 1 mirrors is presented. The spectrometer with a nominal length of 3.1 m can achieve a high resolving power (resolving power higher than 10000) in the soft X‐ray regime when a small source beam (<3 µm in the grating dispersion direction) and small pixel detector (5 µm effective pixel size) are used. Adding Wolter mirrors to the spectrometer before its dispersive elements can realize the spatial imaging capability, which finds applications in the spectroscopic studies of spatially dependent electronic structures in tandem catalysts, heterostructures, etc. In the pump–probe experiments where the pump beam perturbs the materials followed by the time‐delayed probe beam to reveal the transient evolution of electronic structures, the imaging capability of the Wolter mirrors can offer the pixel‐equivalent femtosecond time delay between the pump and probe beams when their wavefronts are not collinear. In combination with some special sample handing systems, such as liquid jets and droplets, the imaging capability can also be used to study the time‐dependent electronic structure of chemical transformation spanning multiple time domains from microseconds to nanoseconds. The proposed Wolter mirrors can also be adopted to the existing soft X‐ray spectrometers that use the Hettrick–Underwood optical scheme, expanding their capabilities in materials research. [ABSTRACT FROM AUTHOR]

A lipid droplet (LD) core of a cell consists mainly of neutral lipids, triacylglycerols and/or steryl esters (SEs). The structuration of these lipids inside the core is still under debate. Lipid segregation inside LDs has been observed but is sometimes suggested to be an artefact of LD isolation and chemical fixation. LD imaging in their native state and in unaltered cellular environments appears essential to overcome these possible technical pitfalls. Here, imaging techniques for ultrastructural study of native LDs in cellulo are provided and it is shown that LDs are organized structures. Cryo soft X‐ray tomography and deep‐ultraviolet (DUV) transmittance imaging are showing a partitioning of SEs at the periphery of the LD core. Furthermore, DUV transmittance and tryptophan/tyrosine auto‐fluorescence imaging on living cells are combined to obtain complementary information on cell chemical contents. This multimodal approach paves the way for a new label‐free organelle imaging technique in living cells. [ABSTRACT FROM AUTHOR]

The unique diagnostic possibilities of X‐ray diffraction, small X‐ray scattering and phase‐contrast imaging techniques applied with high‐intensity coherent X‐ray synchrotron and X‐ray free‐electron laser radiation can only be fully realized if a sufficient dynamic range and/or spatial resolution of the detector is available. In this work, it is demonstrated that the use of lithium fluoride (LiF) as a photoluminescence (PL) imaging detector allows measuring of an X‐ray diffraction image with a dynamic range of ∼107 within the sub‐micrometre spatial resolution. At the PETRA III facility, the diffraction pattern created behind a circular aperture with a diameter of 5 µm irradiated by a beam with a photon energy of 500 eV was recorded on a LiF crystal. In the diffraction pattern, the accumulated dose was varied from 1.7 × 105 J cm−3 in the central maximum to 2 × 10−2 J cm−3 in the 16th maximum of diffraction fringes. The period of the last fringe was measured with 0.8 µm width. The PL response of the LiF crystal being used as a detector on the irradiation dose of 500 eV photons was evaluated. For the particular model of laser‐scanning confocal microscope Carl Zeiss LSM700, used for the readout of the PL signal, the calibration dependencies on the intensity of photopumping (excitation) radiation (λ = 488 nm) and the gain have been obtained. [ABSTRACT FROM AUTHOR]

Spectro-ptychography offers improved spatial resolution and additional phase spectral information relative to that provided by scanning transmission X-ray microscopes. However, carrying out ptychography at the lower range of soft X-ray energies (e.g. below 200 eV to 600 eV) on samples with weakly scattering signals can be challenging. Here, results of soft X-ray spectro-ptychography at energies as low as 180 eV are presented, and its capabilities are illustrated with results from permalloy nanorods (Fe 2p), carbon nanotubes (C 1s) and boron nitride bamboo nanostructures (B 1s, N 1s). The optimization of low-energy X-ray spectro-ptychography is described and important challenges associated with measurement approaches, reconstruction algorithms and their effects on the reconstructed images are discussed. A method for evaluating the increase in radiation dose when using overlapping sampling is presented. [ABSTRACT FROM AUTHOR]

Transmission measurements of the soft X-ray beamline to the Small Quantum Systems (SQS) scientific instrument at the SASE3 undulator of European XFEL are presented. Measurements are reported for a wide range of photon energies (650 eV to 2400 eV), using X-ray gas monitors as well as a bolometric radiometer. The results are in good agreement with simulations for the beam transport and show a transmission of up to 80% over the whole photon energy range. The contribution of second- and third-harmonic radiation of the soft X-ray undulator is determined at selected photon energies by performing transmission measurements using a gas absorber to provide variable attenuation of the incoming photon flux. A comparison of the results with semi-analytic calculations for the generation of free-electron laser pulses in the SASE3 undulator reveals an influence of apertures along the beam transport on the exact harmonic content to be accounted for at the experiment. The secondharmonic content is measured to be in the range of 0.1% to 0.3%, while the third-harmonic contributed a few percent to the SASE3 emission. For experiments at the SQS instrument, these numbers can be reduced through specific selections of the mirror reflection angles. [ABSTRACT FROM AUTHOR]

A compact and portable magnet system for measuring magnetic dichroism in resonant inelastic soft X-ray scattering (SX-RIXS) has been developed at the beamline BL07LSU in SPring-8. A magnetic circuit composed of Nd-Fe-B permanent magnets, which realised ∼0.25 T at the center of an 11 mm gap, was rotatable around the axis perpendicular to the X-ray scattering plane. Using the system, a SX-RIXS spectrum was obtained under the application of the magnetic field at an angle parallel, nearly 45° or perpendicular to the incident X-rays. A dedicated sample stage was also designed to be as compact as possible, making it possible to perform SX-RIXS measurements at arbitrary incident angles by rotating the sample stage in the gap between the magnetic poles. This system enables facile studies of magnetic dichroism in SX-RIXS for various experimental geometries of the sample and the magnetic field. A brief demonstration of the application is presented. [ABSTRACT FROM AUTHOR]

A split-and-delay unit for the extreme ultraviolet and soft X-ray spectral regions has been built which enables time-resolved experiments at beamlines FL23 and FL24 at the Free-electron LASer in Hamburg (FLASH). Geometric wavefront splitting at a sharp edge of a beam splitting mirror is applied to split the incoming soft X-ray pulse into two beams. Ni and Pt coatings at grazing incidence angles have been chosen in order to cover the whole spectral range of FLASH2 and beyond, up to h- = 1800 eV. In the variable beam path with a grazing incidence angle of #d = 1.8-, the total transmission (T) ranges are of the order of 0.48 < T < 0.84 for h- < 100 eV and T > 0.50 for 100 eV < h- < 650 eV with the Ni coating, and T > 0.06 for h- < 1800 eV for the Pt coating. For a fixed beam path with a grazing incidence angle of #f = 1.3-, a transmission of T > 0.61 with the Ni coating and T > 0.23 with a Pt coating is achieved. Soft X-ray pump/soft X-ray probe experiments are possible within a delay range of -5 ps < -t < +18 ps with a nominal time resolution of tr = 66 as and a measured timing jitter of t j = 121 - 2 as. First experiments with the split-and-delay unit determined the averaged coherence time of FLASH2 to be -c = 1.75 fs at - = 8 nm, measured at a purposely reduced coherence of the free-electron laser. [ABSTRACT FROM AUTHOR]

Femtosecond transient soft X-ray absorption spectroscopy (XAS) is a very promising technique that can be employed at X-ray free-electron lasers (FELs) to investigate out-of-equilibrium dynamics for material and energy research. Here, a dedicated setup for soft X-rays available at the Spectroscopy and Coherent Scattering (SCS) instrument at the European X-ray Free-Electron Laser (European XFEL) is presented. It consists of a beam-splitting off-axis zone plate (BOZ) used in transmission to create three copies of the incoming beam, which are used to measure the transmitted intensity through the excited and unexcited sample, as well as to monitor the incoming intensity. Since these three intensity signals are detected shot by shot and simultaneously, this setup allows normalized shot-by-shot analysis of the transmission. For photon detection, an imaging detector capable of recording up to 800 images at 4.5 MHz frame rate during the FEL burst is employed, and allows a photonshot-noise-limited sensitivity to be approached. The setup and its capabilities are reviewed as well as the online and offline analysis tools provided to users. [ABSTRACT FROM AUTHOR]

The PERCIVAL detector is a CMOS imager designed for the soft X-ray regime at photon sources. Although still in its final development phase, it has recently seen its first user experiments: ptychography at a free-electron laser, holographic imaging at a storage ring and preliminary tests on X-ray photon correlation spectroscopy. The detector performed remarkably well in terms of spatial resolution achievable in the sample plane, owing to its small pixel size, large active area and very large dynamic range; but also in terms of its frame rate, which is significantly faster than traditional CCDs. In particular, it is the combination of these features which makes PERCIVAL an attractive option for soft X-ray science. [ABSTRACT FROM AUTHOR]

The advent of X-ray free-electron lasers (XFELs) has revolutionized fundamental science, from atomic to condensed matter physics, from chemistry to biology, giving researchers access to X-rays with unprecedented brightness, coherence and pulse duration. All XFEL facilities built until recently provided X-ray pulses at a relatively low repetition rate, with limited data statistics. Here, results from the first megahertz-repetition-rate X-ray scattering experiments at the Spectroscopy and Coherent Scattering (SCS) instrument of the European XFEL are presented. The experimental capabilities that the SCS instrument offers, resulting from the operation at megahertz repetition rates and the availability of the novel DSSC 2D imaging detector, are illustrated. Timeresolved magnetic X-ray scattering and holographic imaging experiments in solid state samples were chosen as representative, providing an ideal test-bed for operation at megahertz rates. Our results are relevant and applicable to any other non-destructive XFEL experiments in the soft X-ray range. [ABSTRACT FROM AUTHOR]

A new monochromator called an extra-focus constant-included-angle varied-line-spacing (VLS) cylindrical-grating monochromator (extra-focus CIA-VCGM) is described. This monochromator is based on the Hettrick-Underwood scheme where the plane VLS grating is replaced by a cylindrical one in order to zero the defocus at three reference photon energies in the vacuum-ultraviolet range. It has a simple mechanical structure and a fixed focus spot with high performance over a wide energy range. Furthermore, its mechanical compatibility with a standard VLS plane-grating monochromator allows convenient extension into the soft-X-ray range. [ABSTRACT FROM AUTHOR]

A set of electron time-of-flight spectrometers for high-resolution angle-resolved spectroscopy was developed for the Small Quantum Systems (SQS) instrument at the SASE3 soft X-ray branch of the European XFEL. The resolving power of this spectrometer design is demonstrated to exceed 10 000 (E/ΔE), using the well known Ne 1s-13p resonant Auger spectrum measured at a photon energy of 867.11 eV at a third-generation synchrotron radiation source. At the European XFEL, a width of ~0.5 eV full width at half-maximum for a kinetic energy of 800 eV was demonstrated. It is expected that this linewidth can be reached over a broad range of kinetic energies. An array of these spectrometers, with different angular orientations, is tailored for the Atomic-like Quantum Systems endstation for high-resolution angle-resolved spectroscopy of gaseous samples. [ABSTRACT FROM AUTHOR]

The observation method of photoemission electron microscopy (PEEM) on insulating samples has been established in an extremely simple way. Surface conductivity is induced locally on an insulating surface by continuous radiation of soft X-rays, and Au films close to the area of interest allow the accumulated charges on the insulated area to be released to ground level. Magnetic domain observations of a NiZn ferrite, local X-ray absorption spectroscopy of sapphire, high-resolution imaging of a poorly conducting Li0.9CoO2 film surface, and Au pattern evaporation on a fine rock particle are demonstrated. Using this technique, all users' experiments on poorly conducting samples have been performed successfully at the PEEM experimental station of SPring-8. [ABSTRACT FROM AUTHOR]

Synchrotron-based scanning transmission soft X-ray microscopy (STXM) with nanometer resolution was used to investigate the existence and behavior of interfacial gas nanobubbles confined between two silicon nitride windows. The observed nanobubbles of SF6 and Ne with diameters smaller than 2.5 µm were quite stable. However, larger bubbles became unstable and grew during the soft X-ray imaging, indicating that stable nanobubbles may have a length scale, which is consistent with a previous report using atomic force microscopy [Zhang et al. (2010), Soft Matter, 6, 4515-4519]. Here, it is shown that STXM is a promising technique for studying the aggregation of gases near the solid/water interfaces at the nanometer scale. [ABSTRACT FROM AUTHOR]