Search

Background: Metal wear and corrosion from modular junctions in total hip arthroplasty can lead to further unwanted surgery. Trunnion tribocorrosion is recognized as an important contributor to failure. This study was performed to determine if new metal heads restore mechanical integrity of the original modular junction after impaction on corroded trunnions, and assess which variables affect stability of the new interface created at revision total hip arthroplasty.Methods: Twenty-two trunnions, cobalt-chromium (CoCr) and titanium alloy (TiAIV), (CoCr, n = 12; TiAIV, n = 10) and new metal heads were used, 10 trunnions in pristine condition and 12 with corrosion damage. Test states were performed using an MTS Machine and included the following: 1, Assembly; 2, Disassembly; 3, Assembly; 4, Toggling; and 5, Disassembly. During loading, three-dimensional motion of the head-trunnion junction was measured using a custom jig.Results: There were no statistical differences in the tested mechanical properties between corroded and pristine trunnions implanted with a new metal femoral head. Average micromotion of the head versus trunnion interface was greatest at the start of loading, stabilizing after approximately 50 loading cycles at an average of 30.6 ± 3.2 μm.Conclusion: Corrosion at the trunnion does not disrupt mechanical integrity of the junction when a CoCr head is replaced with a CoCr trunnion. However, increased interface motion of a new metal head on a corroded titanium trunnion requires additional study. The evaluation of ball head size on mechanical integrity of trunnions would also be a potential subject of future investigation, as increasing the ball head size at the time of revision is not uncommon in revisions today. [ABSTRACT FROM AUTHOR]

Background: Dual mobility designs were introduced to increase stability and reduce the risk of dislocation, both being common reasons for surgical revision after total hip arthroplasty. The in vivo behavior of dual mobility constructs remains unclear, and to our knowledge, no data have been published describing in vivo surface damage to the polyethylene bearing surfaces.Methods: We used surface damage assessed on the inner and outer polyethylene bearing surfaces in 33 short-term retrieved dual mobility liners as evidence of relative motion at the 2 bearings. A lever out test was performed to determine the force required for dislocation of the cobalt-chromium femoral head from the polyethylene liner.Results: Both bearings showed damage; however, the inner polyethylene bearings had higher damage scores, lower prevalence of remaining machining marks, and higher incidence of concentric wear, all consistent with more motion at the inner polyethylene bearing. The inner polyethylene bearings also had a higher occurrence of embedded titanium debris. The damage sustained in vivo was insufficient to lead to intraprosthetic dislocation in any of the retrieved components. Lever out tests of 12 retrievals had a mean dislocation load of 261 ± 52 N, which was unrelated to the length of implantation.Conclusion: Our short-term retrieval data of 33 highly cross-linked polyethylene dual mobility components suggest that although motion occurs at both bearing articulations, the motion of the femoral head against the inner polyethylene bearing dominates. Although damage was not severe enough to lead to intraprosthetic dislocation, failure may occur long term and should be assessed in future studies. [ABSTRACT FROM AUTHOR]

Background: Bearing surfaces in total hip arthroplasty (THA) may affect implant longevity and hence patient outcomes. This randomized clinical trial determined how ceramic-on-ceramic (CERAMIC) bearing THA affected joint-specific pain, function, and stiffness and prosthesis fixation/longevity over 10 postoperative years compared with ceramic-on-highly-crosslinked-polyethylene (POLYETHYLENE) bearing THA. This is a follow-up to previously reported 5-year outcomes.Methods: Subjects aged <61 years were randomized to CERAMIC (n = 48) or POLYETHYLENE (n = 44) THA. Subjects were assessed using the Western Ontario McMaster Osteoarthritis Index and the RAND 12-Item Health Survey preoperatively, and at 1, 5, and 10 years postoperatively. Plain radiographs were evaluated at 10 years for fixation, and medical records were reviewed for revisions.Results: Of 92 subjects, 6 (7%) died within 10 years; 68 (79%) survivors provided radiographic and/or clinical follow-up at 10 years postoperatively. Improvements seen at 5 years in both the Western Ontario McMaster Osteoarthritis Index and RAND 12-Item Health Survey were retained at 10 years with no group differences (P > .48). There were no failures or loss of fixation related to bearing surfaces/wear in either group. Over 10 years, 3 subjects in the POLYETHYLENE group had revisions that were related to recurrent dislocation; 2 revisions were performed within 2 years of surgery, and one further subject underwent revision at 7 years postoperatively.Conclusions: This is one of the first randomized clinical trials to examine 10-year outcomes between CERAMIC and POLYETHYLENE bearing THAs. Both bearing surfaces performed well out to 10 years in subjects who were <61 years at time of surgery. [ABSTRACT FROM AUTHOR]

Background: Large-diameter, monoblock acetabular components have been used for both hip resurfacing arthroplasty and metal-on-metal (MoM) total hip arthroplasty (THA). If revision is required, one solution is to retain the shell and use a dual-mobility bearing.Methods: We reviewed the results of 25 revision THAs including 11 hip resurfacing arthroplasty and 14 MoM THAs where a monoblock acetabular component was mated to a dual-mobility bearing.Results: At a mean of 29 months, there was one failure, an intraprosthetic dislocation of the dual-mobility bearing. There was a significant decrease in serum metal ion levels postoperatively.Conclusion: Retention of a well-fixed, monoblock MoM acetabular shell and mating it to a dual-mobility bearing in the setting of revision surgery seems to be a reasonable, low-morbidity option at short-term follow-up in appropriately positioned cups. [ABSTRACT FROM AUTHOR]

We reviewed 27 patients who underwent revision for an adverse local tissue reaction (ALTR) secondary to corrosion at the head-neck junction with MoP bearings. Serum cobalt and chromium levels were elevated in all cases, with a mean cobalt of 11.2 ppb and chromium of 2.2 ppb. Patients underwent modular bearing exchange, including a ceramic head with a titanium sleeve in 23 of 27 cases with only one recurrence of ALTR in one of the four patients not treated with a ceramic head. The diagnosis of ALTR secondary to corrosion is associated with cobalt levels of >1 ppb with cobalt levels elevated above chromium. Retention of a well-fixed stem and modular exchange to a ceramic head leads to resolution of symptoms and decreases in metal levels. [ABSTRACT FROM AUTHOR]

This study reports mid-term results of Delta ceramic on ceramic (COC) in total hip arthroplasty (THA). Subjects received Delta COC THA in a prospective multi-center study with either 28 mm ( n = 177) or 36 mm ( n = 168) articulations. Annual clinical and radiographic evaluations were performed, and patients were asked about hip noises. At mean 5.3-year follow-up there were 3 (0.9%) post-operative liner fractures. Nine revisions were performed (2 liner fracture, 4 stem loosening, 3 deep infection). Kaplan-Meier survivorship at 6 years was 96.9% (94.0–98.4). Twenty-six (7.5%) subjects reported squeaking, of whom none were revised. One (0.3%) subject could reproduce a sound in clinic. More patients reported squeaking with a 36 mm bearing (28 mm: 7/177, 36 mm: 19/168, P = 0.013). [ABSTRACT FROM AUTHOR]

Background: Previous studies have demonstrated equivalent survivorship of modular metal-backed tibial (MBT) and all-polyethylene tibial (APT) components. The purpose of this study is to compare the utilization and outcomes of APT and MBT components in a large US database.Methods: The American Joint Replacement Registry was queried to identify all patients undergoing primary total knee arthroplasty (TKA) during the study period from 2012 to 2019. These patients were divided into cohorts based on tibial component (APT or MBT). Cohort demographics including gender, hospital size, hospital teaching status, region, age, and Charlson Comorbidity Index were reported with descriptive statistics. Overall reoperation rates and revisions for infection, aseptic loosening, periprosthetic fracture, manipulation under anesthesia, and revision for other reasons were identified using International Classification of Diseases, Ninth Revision and Current Procedural Terminology codes and compared across APT and MBT cohorts. Kaplan-Meir survival analysis was performed based on reason for reoperation for APT and MBT.Results: During the study period, 703,007 TKAs were reported with 97.8% utilizing MBT and 2.2% utilizing APT components. Despite the introduction of alternative payment models during the study period, the utilization of APT decreased from 5.8% in 2012 to 1.7% in 2019. The survival of APT and MBT TKAs were similar across the study period: 98.1% vs 98.6% at 8 years. The rate of reoperation for all-causes was higher for APT compared to MBT (1.36% vs 1.00%; odds ratio 1.52).Conclusion: Despite their paucity of use and lower cost APT remained within a 0.4% margin of survivorship when compared to MBT implants for up to 8 years.Level Of Evidence: Level III, retrospective. [ABSTRACT FROM AUTHOR]

Abstract: This study determined how ceramic-on-ceramic bearing THA affected joint-specific pain, function and stiffness in the first five postoperative years compared with ceramic-on-highly-crosslinked-polyethylene bearing THA. Subjects less than 61 years of age were randomized to ceramic-on-ceramic (CERAMIC) [n = 48] or ceramic-on-highly-crosslinked-polyethylene (POLYETHYLENE) [n = 44] bearing THA. Subjects were assessed using the Western Ontario McMaster Osteoarthritis Index (WOMAC) and the RAND 12-Item Health Survey (RAND-12) preoperatively, and at one and five years postoperatively. 92 subjects(50 (54%) males; average age = 52 (SD 6.6) years) were enrolled. 78 (85%) subjects returned five years postoperatively. All subjects reported improvements at one and five years in all measured indices with no group differences detected. Seven (8%) subjects experienced postoperative THA complications, none related to bearing surfaces; two subjects (POLYETHYLENE) required revision for instability. Both bearing surfaces provided excellent short-term results in younger subjects. [Copyright &y& Elsevier]

Abstract: We evaluated the outcomes of 64 consecutive revision total hip arthroplasties with an alumina-on-alumina bearing surface in 61 patients with osteolysis. No implants had been rerevised nor was osteolysis detected at a mean of 9.8 years (range, 7.0-13.1 years) postoperatively. There was 1 case of stem loosening but no cup loosening or alumina bearing fractures. Two surgical procedures were performed for an infection in 1 patient. Three dislocations occurred in 3 hips; all were treated with closed reduction and abduction bracing for 3 months. No further dislocations occurred. With any reoperation or radiographic evidence of osteolysis or loosening as the end point, the 7-year survival rate was 96.9% (95% confidence interval, 90.8%-100%). The alumina-on-alumina bearing surfaces used for revision total hip arthroplasty in patients with osteolysis were found to produce encouraging clinical results and implant survival rates at a minimum of 7 years postoperatively. [Copyright &y& Elsevier]

While mechanically-assisted crevice corrosion (MACC) at the head/neck junction of modular total hip arthroplasty (THA) femoral components was first described over two decades ago, it is only within the last few years that investigators have observed that adverse local tissue reactions (ALTRs) associated with MACC are an increasingly prevalent mode of failure of contemporary THAs. As yet, the incidence, etiology and pathogenesis of MACC-associated ALTR are not well understood. In this review, possible implant-, patient-, and surgeon-related factors are considered in the context of a small but growing body of evidence from laboratory simulations, implant and tissue retrieval studies and clinical case series. It is likely that MACC-associated ALTR is a multifactorial process and that ongoing research will lead to multiple strategies that will facilitate early diagnosis and ultimately prevention of the adverse clinical sequelae of this phenomenon. [ABSTRACT FROM AUTHOR]

Abstract: Ceramic bearing surfaces have been introduced to prevent bone loss after osteolysis seen with conventional polyethylene bearing surfaces. One hundred three ceramic-on-ceramic total hip arthroplasties in 97 patients were retrospectively reviewed. Average follow-up was 50.4 months. Preoperative Harris Hip Score was 49.5 points, which improved to 87.2 postoperatively (P < .05). Pain score improved from 13.7 points preoperatively to 40.6 points postoperatively (P < .05). Functional score improved from 30 points preoperatively to 41 points postoperatively (P < .05). No fractures, dislocations, infections, or osteolysis was observed on radiographs. Five patients (4.9%), at 11, 16, 30, 38, and 60 months postoperatively, presented with “squeaky” hips that continue to perform well. Long-term studies will be required to determine the true efficacy of these hard bearing surfaces. [Copyright &y& Elsevier]

Abstract: The purpose of this study was to compare the linear penetration rates of a highly cross-linked ultra–high-molecular-weight polyethylene to traditional polyethylene. Twenty-seven highly cross-linked components were matched to 27 traditional polyethylene components with respect to age, sex, body mass index, and activity level. Each group was followed up for a mean of approximately 6 years. Linear penetration was measured using Martell''s computerized technique (J Bone Joint Surg Am 1997;79:1635). The mean total penetration was 0.283 mm (SD, 0.253) for the highly cross-linked group. The mean total penetration for the traditional polyethylene was 0.696 mm (SD, 0.402). This difference was highly significant (P ≤ .001). Our experience demonstrates a 59% reduction in total penetration of highly cross-linked polyethylene when compared with traditional polyethylene at a minimum of 5 years. [Copyright &y& Elsevier]

Abstract: The longevity of any hip arthroplasty in an individual patient cannot be predicted with certainty so revisability of the arthroplasty remains an issue. As the occurrence of loosening and osteolysis decreases, then fatigue failure of femoral stems, complications of modular connections, and infection will become relatively more common modes of failure. Metal-metal hip resurfacing conserves bone stock, which provides better options for revision surgery. Hip resurfacing favors early intervention and has demonstrated excellent outcomes in young active males, the group historically at increased risk for failure of a conventional total hip arthroplasty. The best balance of the benefit-risk ratio for hip resurfacing is in those patients at increased risk for failure of a conventional total hip arthroplasty. [Copyright &y& Elsevier]

Background: Dual mobility designs were introduced to increase stability and reduce the risk of dislocation, both being common reasons for surgical revision after total hip arthroplasty. The in vivo behavior of dual mobility constructs remains unclear, and to our knowledge, no data have been published describing in vivo surface damage to the polyethylene bearing surfaces., Methods: We used surface damage assessed on the inner and outer polyethylene bearing surfaces in 33 short-term retrieved dual mobility liners as evidence of relative motion at the 2 bearings. A lever out test was performed to determine the force required for dislocation of the cobalt-chromium femoral head from the polyethylene liner., Results: Both bearings showed damage; however, the inner polyethylene bearings had higher damage scores, lower prevalence of remaining machining marks, and higher incidence of concentric wear, all consistent with more motion at the inner polyethylene bearing. The inner polyethylene bearings also had a higher occurrence of embedded titanium debris. The damage sustained in vivo was insufficient to lead to intraprosthetic dislocation in any of the retrieved components. Lever out tests of 12 retrievals had a mean dislocation load of 261 ± 52 N, which was unrelated to the length of implantation., Conclusion: Our short-term retrieval data of 33 highly cross-linked polyethylene dual mobility components suggest that although motion occurs at both bearing articulations, the motion of the femoral head against the inner polyethylene bearing dominates. Although damage was not severe enough to lead to intraprosthetic dislocation, failure may occur long term and should be assessed in future studies., (Copyright © 2016 Elsevier Inc. All rights reserved.)