Search

Polylactic acid (PLA), as a green functional polymer, has been useful in various coating applications. However, due to the low mechanical strength and thermal stability of PLA, it needs to be improved in order to expand its application areas. In this work, a series of polylactic acid (PLA) nanocomposite films were prepared through introducing polydopamine-modified mica (PDA@MICA) as a self-assemble nanofiller to enhance its mechanical and thermal properties. The results demonstrated that PLA/PDA@MICA shows excellent mechanical properties. Tensile tests showed that PLA/PDA@MICA exhibits a 58.3 % increase in tensile strength and a 16.8 % increase in Young's modulus compared to pure PLA. Meanwhile, thermal performance testing shown the introduction of PDA@MICA led to an increase in crystallinities (Xc = 24.78 %). And the thermal decomposition temperature of PLA/PDA@MICA film (374 °C) was slightly higher than that of PLA film (367 °C). The simultaneous improvement of the mechanical and thermal properties was attributed to the formation of hydrogen bonds between PLA and PDA@MICA. In addition, the parallel arrangement of PDA@MICA and PLA macromolecular chains forms a unique "brick and mortar" structure in the coating, which enhances the mechanical properties of PLA/PDA@MICA composite coatings. This study reports a successful approach to simultaneously address the drawbacks of PLA, specifically its low thermal stability and mechanical strength, thereby promoting its widespread application in the coatings industry. [ABSTRACT FROM AUTHOR]

Two biobased composite films have been prepared with poly (lactic acid-trimethylene carbonate), polylactic acid and Laponite by solvent evaporation method. The 1H NMR and FTIR spectrums illustrate that P (LA-TMC) polymer is successfully synthesized and designed composite films are produced. Morphometric analyses demonstrate that the roughnesses of the film's surface and cross-section are on the increase with higher PLA and Laponite content. Mechanical performances reveal that the rise in tensile strength and modulus while maintaining excellent elongation at break is mainly due to the increase in the content of polylactic acid and Laponite. By utilizing the nano effect of Laponite, the maximum tensile strength of the composite film reaches 34.59 MPa. Thermal property results illustrate that the Tg and initial decomposition temperature are on the growth with the increase of PLA content. However, it is not significant on the effect of Laponite on the initial decomposition temperature. The water vapor permeability measurements prove that the barrier property of P(LA-TMC)/PLA/Laponite composite film is on the ascent with the Laponite addition. Hydrolytic degradation tests indicate that PLA and Laponite play avital part in accelerating the degradation rate of composite films and alkaline media is superior acidic and neutral conditions. [ABSTRACT FROM AUTHOR]

In this study, a method was proposed to prepare biocomposites from polylactic acid (PLA) and polyethylene glycol (PEG)-modified lignin using twin-screw extrusion process. The structure of PEG-modified lignin was studied by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatographic (GPC) analysis. The effects of different contents of soda lignin and PEG-modified lignin on PLA composites were studied by tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA) and degradation analysis. The experimental results showed that the addition of PEG-modified lignin enhanced the heat resistance of PLA composite. PLA could be combined with up to 30 % PEG-modified lignin, with no significant reduction in tensile strength properties. Compared with PLA-L30, the tensile stress and elongation at break of PLA-PL30 were increased by 26.4 % and 78.9 %, respectively. This approach provided a new way to produce high-performance lignin based-PLA composites and had certain industrial application value. • A method for polyethylene glycol (PEG)-modified lignin is proposed. • Biocomposites from polylactic acid (PLA) and PEG modified lignin are investigated. • PEG-modified lignin improves the interface performance with PLA. • The addition of PEG-modified lignin enhances the heat resistance of PLA. • PEG-modified lignin/PLA shows good mechanical properties. [ABSTRACT FROM AUTHOR]

Having poor interfacial compatibility between biochar microsphere (BM) and polylactic acid (PLA) should be responsible for the unbalance of composite film strength and toughness. Elucidating the effect of polydopamine (PDA) on BM and BM/PLA composite films is the ultimate goal of this study based on the mussel bionic principle. It was found that the strong adhesion of PDA on the BM surface was achieved, which improved the surface roughness and thermal stability. Also, PDA modification can facilitate crystallization, increase thermal properties, improve interfacial compatibility, and enhance the tensile properties of BM/PLA composite films. Silane-based PDA modified BM/PLA composite film exhibited the best tensile strength, tensile modulus, and elongation at break with 77.95 MPa, 1.87 GPa, and 7.30%. These noteworthy findings, achieving a simultaneous improvement in PLA strength and toughness, hold promising implications for its sustainability. [Display omitted] [ABSTRACT FROM AUTHOR]

Applications for polylactic acid (PLA) are significantly impacted by its poor mechanical properties and lack of thermal stability. The goal of this work is to bridge the gap of poor compatibility among the components and enhance their interface interlocking capability to improve the toughness and thermal stability. Ultrafine bamboo charcoal (UFBC) was treated through deep eutectic solvent (DES) method to deposit sodium lignosulfonate (LS) on its surface. LS was used with PLA as a bio-coupling agent to create an eco-friendly PLA composite film with a wide range of characteristics. Benefiting from the penetration of PLA to the internal pores in UFBC, the resultant L-UFBC/PLA film has a good mechanical interlocking structure. Ls can increase the compatibility and strengthen the interface interlocking capability through DES method, which greatly improves the mechanical properties of the system. In comparison to pure PLA one, the elongation at break was 136.24 % greater, and the crystallinity (Xc) increased from 1.09 % to 3.33 %. Furthermore, the thermal stability of the system was also improved, and the residual at 600 °C rose by 4.83 %. These characteristics offer the prepared L-UFBC/PLA film a wide range of potential applications in the packaging, medical, agricultural, and other sectors. [ABSTRACT FROM AUTHOR]

Cardanol (CD) is used as a reactive compatibilizer, and blended with polylactic acid (PLA) and polypropylene carbonate (PPC) resin (70/30(w/w)) to obtain a series of PLA/PPC/CD blends. The systematic study was conducted on the thermal properties, optical properties, rheological properties, mechanical properties, and microscopic morphology of the blend, by varying amounts of CD added to the blends. A detailed explanation and comprehensive analysis of the reaction mechanism between CD and PLA/PPC have been made. The study found that CD acts as a "bridge" between the PLA and PPC, forming the structure of a block copolymer (PLA-b-CD-b-PPC), and the copolymer can greatly improve the compatibility of PLA and PPC. When the amount of CD reaches 8 wt%, only one T g is observed in the blend, simultaneously, PLA/PPC has already transitioned from a partially compatible system to a completely compatible system. At the same time, the addition of CD does not have any negative impact on the thermal stability of the PLA/PPC blend under processing temperature conditions, and the thermal stability of the PLA/PPC/CD blends can even be improved under extreme conditions. In addition, the addition of CD allows the PLA/PPC/CD blends to maintain a high light transmittance while reducing the opacity of the blend (the light transmittance remains above 92 %, and the opacity is reduced from 37 % to about 24 %), demonstrating excellent optical properties. Moreover, the elongation at break and impact strength of the PLA/PPC/CD blend both show a trend of first increasing and then decreasing with the increase of CD amount. When the CD amount varies within the range of 6– 8 wt%, the blends undergoes a brittle-ductile transition, and its toughness is greatly improved while the rigidity can also meet practical needs. When the amount of CD in the system increases to 12 wt%, the toughness of the blend reaches its peak, and its elongation at break and impact strength reach 513.24 % and 9211.5 J/m2 respectively (increased to 2442.84 % and 270.73 % of the PLA/PPC blend). Concurrently, the fracture surface of the blend exhibits large-scale plastic flow in the direction of the applied force, with marked shear yield phenomena, showing obvious characteristics of tough fracture. [Display omitted] [ABSTRACT FROM AUTHOR]

3D-printing provides a feasible technique for realizing new materials into structural and intelligent parts. In this work, biomass furan-based polyesters poly (ethylene furanoate) (PEF), poly (trimethylene furanoate) (PTF), and poly (butylene furanoate) (PBF) were successfully synthesized in a 5 L reactor through the melt polycondensation process and fabricated into 3D-printing feedstocks. It was demonstrated that the three furan-based polyesters were additively-manufactured into complicated structures. Besides, the mechanical and thermal properties of furan-based polyesters could be tailored by the chain length of diol monomer. The mechanical performance of 3D-printed PEF, PTF and PBF were characterized and compared with commercial filaments. The tensile strength of PEF and PTF could reach 74.6 and 63.8 MPa respectively, which exhibited superior tensile property to poly(ether-ether-ketone) (PEEK), polyamide (PA) and polylactic acid (PLA). Meanwhile, the compression results demonstrated that the PEF and PTF possessed comparable energy absorption capacity with PEEK and PLA respectively, which indicated excellent mechanical properties of furan-based polyesters. It was interesting to find that the 3D-printed structures including solid cube, bionic flower and lattice structures were employed to prove that the PTF possessed excellent shape memory properties. Therefore, the proposed biomass furan-based polymers would offer more freedom in the field of 3D-printing. [ABSTRACT FROM AUTHOR]