Search

The challenge of dispersing nanocellulose in hydrophobic polymers such as polylactic acid (PLA) still obstacles the further application of cellulose nanocomposites. An environment-friendly and facile wet-shearing pretreatment strategy without using any organic solvent was developed in this work. Silane modified lignocellulose nanofiber (SLCNF) was pre-dispersed into PLA by wet-shearing pretreatment, followed by extrusion process and the SLCNF could be dispersed extremely well in PLA matrices. SLCNF formed a crosslinked network and had an improved compatibility, which improved the mechanical and thermal properties of PLA composites. The tensile strength, elongation at break and thermal deformation temperature of the composites were increased by 12.6 %, 32.4 % and 9.1 °C, respectively. Moreover, SLCNF promoted the crystallization of PLA as a heterogeneous nucleating agent and the crystallinity was increased by about 40 %. This study provides an effective way to disperse nanocellulose in polymer matrix with high efficiency to enhance polymer-based composites. • Wet-shearing pretreatment combined with oven drying is an effective method for dispersing nanocellulose in polymer matrix. • Silane modified reed straw nanofibers formed a cross-linked network and have an improved compatibility with PLA matrix. • Enhanced mechanical, thermal and crystallization properties of polylactic acid/reed straw nanofiber blends [ABSTRACT FROM AUTHOR]

Biodegradable composites were prepared from polylactic acid (PLA) and bamboo charcoal (BC) by melt blending and hot pressing. The effects of BC addition on the mechanical properties, water absorption, DMA, TGA, DSC, and CONE of BC/PLA composites were investigated. The microscopic morphology of the composites was analyzed by SEM. The results showed that for BC addition of 40 wt%, the mechanical strength, thermal properties, and flame retardant properties of the composites were improved compared with those of PLA, with a 2.24 % increase in flexural strength and a 1535 % increase (500 °C) in TG mass retention rate. The crystallinity increased by 129.66 %, the peak loss factor decreased by 31.15 %, the time required for combustion was delayed by 168 s, the peak heat release rate decreased by 29.40 %, the carbon residue rate detected by cone calorimetry increased by 48.50 %, and the peak mass loss rate decreased by 48.82 %. The addition of BC enhanced the crystallization capacity of PLA, and improved the thermal properties and flame retardant properties of the prepared composites. The results showed that materials prepared with a BC content of 40 wt% exhibited the best overall performance. • Bamboo charcoal/polylactic acid biodegradable composites were prepared by melt blending and hot pressing. • The effects of the amount of added BC on properties of composites and their mechanisms were determined. • BC/PLA composites obtained high water resistance, thermal properties, thermal stability, and flame retardant properties. • The application field of Bamboo charcoal has been expanded. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA), as a green functional polymer, has been useful in various coating applications. However, due to the low mechanical strength and thermal stability of PLA, it needs to be improved in order to expand its application areas. In this work, a series of polylactic acid (PLA) nanocomposite films were prepared through introducing polydopamine-modified mica (PDA@MICA) as a self-assemble nanofiller to enhance its mechanical and thermal properties. The results demonstrated that PLA/PDA@MICA shows excellent mechanical properties. Tensile tests showed that PLA/PDA@MICA exhibits a 58.3 % increase in tensile strength and a 16.8 % increase in Young's modulus compared to pure PLA. Meanwhile, thermal performance testing shown the introduction of PDA@MICA led to an increase in crystallinities (Xc = 24.78 %). And the thermal decomposition temperature of PLA/PDA@MICA film (374 °C) was slightly higher than that of PLA film (367 °C). The simultaneous improvement of the mechanical and thermal properties was attributed to the formation of hydrogen bonds between PLA and PDA@MICA. In addition, the parallel arrangement of PDA@MICA and PLA macromolecular chains forms a unique "brick and mortar" structure in the coating, which enhances the mechanical properties of PLA/PDA@MICA composite coatings. This study reports a successful approach to simultaneously address the drawbacks of PLA, specifically its low thermal stability and mechanical strength, thereby promoting its widespread application in the coatings industry. [ABSTRACT FROM AUTHOR]

Currently, it is still a huge challenge to prepare high performance eco-friendly poly(lactic acid) (PLA) with high thermal stability, good processability, excellent crystallization behavior, good transparency and highly-efficient fire safety. In this paper, a novel bio-based nucleation agent N-(furan-2-ylmethyl)- P , P -diphenylphosphinic amide (FPPA) was prepared and used for the fabrication of fire safety PLA/FPPA composites. The chemical structure of FPPA was measured by FTIR, NMR and MS. Further, the crystallization behavior, thermal stability, fire safety and mechanical properties of PLA/FPPA composites were performed by TGA, DSC, polarization microscope, LOI, UL94, cone calorimeter, DMA and, SEM, Raman, GC–MS, and TGA-FTIR. The results showed that the multifunctional FPPA not only had a high thermal stability and was a good nucleation agent for PLA. Moreover, only loading of 3 wt% FPPA increased the LOI of PLA from 19.0 to 33.8 % with UL-94 V-0 classification. Furthermore, the heat release rate and total heat release values of PLA/3%FPPA composite reduced by 6.3 % and 15.3 % in cone-calorimeter test. Such high fire safety was mainly attributed to specific fire safety radicals due to thermal degradation of FPPA to interrupt composites burning in gas phase. Besides, transparency and mechanical properties were almost not changed because of low loading of FPPA in PLA. This multifunctional bio-based fire-retardant for PLA with good comprehensive performance promises broad application in engineering electronics, automobiles, 3D printing and construction materials. [ABSTRACT FROM AUTHOR]

• PNS is a sustainable filler to develop cost-effective PLA biocomposites. • PNS enhanced PLA thermal stability, viscoelastic response, and crystallinity. • High filler loading did not cause significant decay in mechanical properties. • Ball milling of PNS further improved PLA thermal properties and melt fluidity. • Thermal annealing enhanced HDT, stiffness and strength of biocomposites. Biodegradable polymer composites reinforced with agri-food lignocellulosic biowaste represent cost-effective and sustainable materials potentially able to replace traditional composites for structural, household, and packaging applications. Herein, the preparation of polylactic acid (PLA)/pecan (Carya illinoinensis) nutshell (PNS) biocomposites at high filler loading (50 wt%) is reported, alongside the effect of two environmentally friendly physical treatments, namely ball-milling of the filler and thermal annealing on biocomposites. PNS enhanced the thermal stability, the viscoelastic response, and the crystallinity of the polymer. Furthermore, filler ball-milling also increased the melt fluidity of the biocomposites, potentially improving melt processing. Finally, the presence of PNS remarkably enhanced the effect of thermal annealing in the compounds. In particular, heat deflection temperature of the biocomposites dramatically increased, up to 60 °C with respect to the non-annealed samples. Overall, these results emphasize the potential of combining natural fillers and environmentally benign physical treatments to tailor the properties of PLA biocomposites, especially for those applications which require a stiff and lightweight material with low deformability. [ABSTRACT FROM AUTHOR]

Two biobased composite films have been prepared with poly (lactic acid-trimethylene carbonate), polylactic acid and Laponite by solvent evaporation method. The 1H NMR and FTIR spectrums illustrate that P (LA-TMC) polymer is successfully synthesized and designed composite films are produced. Morphometric analyses demonstrate that the roughnesses of the film's surface and cross-section are on the increase with higher PLA and Laponite content. Mechanical performances reveal that the rise in tensile strength and modulus while maintaining excellent elongation at break is mainly due to the increase in the content of polylactic acid and Laponite. By utilizing the nano effect of Laponite, the maximum tensile strength of the composite film reaches 34.59 MPa. Thermal property results illustrate that the Tg and initial decomposition temperature are on the growth with the increase of PLA content. However, it is not significant on the effect of Laponite on the initial decomposition temperature. The water vapor permeability measurements prove that the barrier property of P(LA-TMC)/PLA/Laponite composite film is on the ascent with the Laponite addition. Hydrolytic degradation tests indicate that PLA and Laponite play avital part in accelerating the degradation rate of composite films and alkaline media is superior acidic and neutral conditions. [ABSTRACT FROM AUTHOR]

In this study, a method was proposed to prepare biocomposites from polylactic acid (PLA) and polyethylene glycol (PEG)-modified lignin using twin-screw extrusion process. The structure of PEG-modified lignin was studied by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatographic (GPC) analysis. The effects of different contents of soda lignin and PEG-modified lignin on PLA composites were studied by tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA) and degradation analysis. The experimental results showed that the addition of PEG-modified lignin enhanced the heat resistance of PLA composite. PLA could be combined with up to 30 % PEG-modified lignin, with no significant reduction in tensile strength properties. Compared with PLA-L30, the tensile stress and elongation at break of PLA-PL30 were increased by 26.4 % and 78.9 %, respectively. This approach provided a new way to produce high-performance lignin based-PLA composites and had certain industrial application value. • A method for polyethylene glycol (PEG)-modified lignin is proposed. • Biocomposites from polylactic acid (PLA) and PEG modified lignin are investigated. • PEG-modified lignin improves the interface performance with PLA. • The addition of PEG-modified lignin enhances the heat resistance of PLA. • PEG-modified lignin/PLA shows good mechanical properties. [ABSTRACT FROM AUTHOR]

Having poor interfacial compatibility between biochar microsphere (BM) and polylactic acid (PLA) should be responsible for the unbalance of composite film strength and toughness. Elucidating the effect of polydopamine (PDA) on BM and BM/PLA composite films is the ultimate goal of this study based on the mussel bionic principle. It was found that the strong adhesion of PDA on the BM surface was achieved, which improved the surface roughness and thermal stability. Also, PDA modification can facilitate crystallization, increase thermal properties, improve interfacial compatibility, and enhance the tensile properties of BM/PLA composite films. Silane-based PDA modified BM/PLA composite film exhibited the best tensile strength, tensile modulus, and elongation at break with 77.95 MPa, 1.87 GPa, and 7.30%. These noteworthy findings, achieving a simultaneous improvement in PLA strength and toughness, hold promising implications for its sustainability. [Display omitted] [ABSTRACT FROM AUTHOR]

Applications for polylactic acid (PLA) are significantly impacted by its poor mechanical properties and lack of thermal stability. The goal of this work is to bridge the gap of poor compatibility among the components and enhance their interface interlocking capability to improve the toughness and thermal stability. Ultrafine bamboo charcoal (UFBC) was treated through deep eutectic solvent (DES) method to deposit sodium lignosulfonate (LS) on its surface. LS was used with PLA as a bio-coupling agent to create an eco-friendly PLA composite film with a wide range of characteristics. Benefiting from the penetration of PLA to the internal pores in UFBC, the resultant L-UFBC/PLA film has a good mechanical interlocking structure. Ls can increase the compatibility and strengthen the interface interlocking capability through DES method, which greatly improves the mechanical properties of the system. In comparison to pure PLA one, the elongation at break was 136.24 % greater, and the crystallinity (Xc) increased from 1.09 % to 3.33 %. Furthermore, the thermal stability of the system was also improved, and the residual at 600 °C rose by 4.83 %. These characteristics offer the prepared L-UFBC/PLA film a wide range of potential applications in the packaging, medical, agricultural, and other sectors. [ABSTRACT FROM AUTHOR]

Cardanol (CD) is used as a reactive compatibilizer, and blended with polylactic acid (PLA) and polypropylene carbonate (PPC) resin (70/30(w/w)) to obtain a series of PLA/PPC/CD blends. The systematic study was conducted on the thermal properties, optical properties, rheological properties, mechanical properties, and microscopic morphology of the blend, by varying amounts of CD added to the blends. A detailed explanation and comprehensive analysis of the reaction mechanism between CD and PLA/PPC have been made. The study found that CD acts as a "bridge" between the PLA and PPC, forming the structure of a block copolymer (PLA-b-CD-b-PPC), and the copolymer can greatly improve the compatibility of PLA and PPC. When the amount of CD reaches 8 wt%, only one T g is observed in the blend, simultaneously, PLA/PPC has already transitioned from a partially compatible system to a completely compatible system. At the same time, the addition of CD does not have any negative impact on the thermal stability of the PLA/PPC blend under processing temperature conditions, and the thermal stability of the PLA/PPC/CD blends can even be improved under extreme conditions. In addition, the addition of CD allows the PLA/PPC/CD blends to maintain a high light transmittance while reducing the opacity of the blend (the light transmittance remains above 92 %, and the opacity is reduced from 37 % to about 24 %), demonstrating excellent optical properties. Moreover, the elongation at break and impact strength of the PLA/PPC/CD blend both show a trend of first increasing and then decreasing with the increase of CD amount. When the CD amount varies within the range of 6– 8 wt%, the blends undergoes a brittle-ductile transition, and its toughness is greatly improved while the rigidity can also meet practical needs. When the amount of CD in the system increases to 12 wt%, the toughness of the blend reaches its peak, and its elongation at break and impact strength reach 513.24 % and 9211.5 J/m2 respectively (increased to 2442.84 % and 270.73 % of the PLA/PPC blend). Concurrently, the fracture surface of the blend exhibits large-scale plastic flow in the direction of the applied force, with marked shear yield phenomena, showing obvious characteristics of tough fracture. [Display omitted] [ABSTRACT FROM AUTHOR]

3D-printing provides a feasible technique for realizing new materials into structural and intelligent parts. In this work, biomass furan-based polyesters poly (ethylene furanoate) (PEF), poly (trimethylene furanoate) (PTF), and poly (butylene furanoate) (PBF) were successfully synthesized in a 5 L reactor through the melt polycondensation process and fabricated into 3D-printing feedstocks. It was demonstrated that the three furan-based polyesters were additively-manufactured into complicated structures. Besides, the mechanical and thermal properties of furan-based polyesters could be tailored by the chain length of diol monomer. The mechanical performance of 3D-printed PEF, PTF and PBF were characterized and compared with commercial filaments. The tensile strength of PEF and PTF could reach 74.6 and 63.8 MPa respectively, which exhibited superior tensile property to poly(ether-ether-ketone) (PEEK), polyamide (PA) and polylactic acid (PLA). Meanwhile, the compression results demonstrated that the PEF and PTF possessed comparable energy absorption capacity with PEEK and PLA respectively, which indicated excellent mechanical properties of furan-based polyesters. It was interesting to find that the 3D-printed structures including solid cube, bionic flower and lattice structures were employed to prove that the PTF possessed excellent shape memory properties. Therefore, the proposed biomass furan-based polymers would offer more freedom in the field of 3D-printing. [ABSTRACT FROM AUTHOR]

Epoxidized soybean oil (ESO) was used as a compatibilizer and blended with polylactic acid (PLA) and polypropylene carbonate (PPC) resin to prepare a series of PLA/PPC/ESO blends with varying compositions. The influence of the variation in the amount of ESO added to the blend system on the thermal properties, optical properties, rheological properties, mechanical properties, and microscopic morphology of the blends was studied. The research indicates that ESO can react with PLA and PPC to form a chemical bond interface, which improves the compatibility of PLA and PPC to a certain extent. With the increase in the amount of ESO added to the blend (1– 5 phr), the complete decomposition temperature, storage modulus, loss modulus, complex viscosity, notched impact strength, and elongation at break of the blend all show a trend of continuous increase. At the same time, the melt flow rate, light transmittance, and tensile strength of the blend do not show significant fluctuations. When the amount of ESO in the system is 5 phr, compared with the PLA/PPC blend, the notched impact strength and elongation at break of the PLA/PPC/ESO blend increase from 4270.3 J/m2, 43.89 % to 8560.4 J/m2, 211.28 %, respectively, and its tensile strength and transmittance still remain around 63 MPa, 92 %. This improves the toughness of the blend while maintaining its rigidity, demonstrating excellent mechanical and optical properties. At this time, the microscopic morphology of the fracture surface of the impact sample also shows obvious characteristics of tough fracture. However, when the amount of ESO added to the blend is excessive (6 phr), the compatibility of the blending system decreases, which will degrade the performance of the blending material and ultimately destroy the phase morphology of the blend and reduce its mechanical properties. [Display omitted] [ABSTRACT FROM AUTHOR]

Epoxidized soybean oil (ESO) was used as a compatibilizer and blended with polylactic acid (PLA) and polypropylene carbonate (PPC) resin to prepare a series of PLA/PPC/ESO blends with varying compositions. The influence of the variation in the amount of ESO added to the blend system on the thermal properties, optical properties, rheological properties, mechanical properties, and microscopic morphology of the blends was studied. The research indicates that ESO can react with PLA and PPC to form a chemical bond interface, which improves the compatibility of PLA and PPC to a certain extent. With the increase in the amount of ESO added to the blend (1– 5 phr), the complete decomposition temperature, storage modulus, loss modulus, complex viscosity, notched impact strength, and elongation at break of the blend all show a trend of continuous increase. At the same time, the melt flow rate, light transmittance, and tensile strength of the blend do not show significant fluctuations. When the amount of ESO in the system is 5 phr, compared with the PLA/PPC blend, the notched impact strength and elongation at break of the PLA/PPC/ESO blend increase from 4270.3 J/m2, 43.89 % to 8560.4 J/m2, 211.28 %, respectively, and its tensile strength and transmittance still remain around 63 MPa, 92 %. This improves the toughness of the blend while maintaining its rigidity, demonstrating excellent mechanical and optical properties. At this time, the microscopic morphology of the fracture surface of the impact sample also shows obvious characteristics of tough fracture. However, when the amount of ESO added to the blend is excessive (6 phr), the compatibility of the blending system decreases, which will degrade the performance of the blending material and ultimately destroy the phase morphology of the blend and reduce its mechanical properties. [Display omitted] [ABSTRACT FROM AUTHOR]

Renewable yet biodegradable natural fiber (e.g., cellulose nanofiber (CNF)) reinforced bio-based polymers (e.g., polylactic acid (PLA)) are being applied for the manufacture of clean packaging products. The interface incompatibility between hydrophilic CNF and hydrophobic PLA still restricts the promotion of high-performance bio-based products. Herein, a polycondensate-coated CNF hybrid, wherein silane, aluminate, and titanate coupling agent monomers were in-situ polymerized onto the CNF surface via dehydration self-condensation, was designed and further employed as strengthening/toughening nanofillers for fabricating the CNF-reinforced PLA composite. Results showed that the polycondensate coatings could efficiently promote the dispersion of CNFs and enhance interfacial compatibility between CNFs and PLA. Attributing to the synergistic effect of polycondensate coatings and CNFs, a considerable improvement in processing, mechanical and thermal properties was obtained in resultant CNF/PLA composites. With adding 2.5 wt% polycondensate-coated CNFs, the tensile strength, Young's modulus, and tensile toughness of CNF-reinforced PLA composites was raised by about 27 %, 51 % and 68 %, respectively; also, such composite possessed greater elasticity and higher melt strength than pure PLA. This study provides a novel interface control strategy to fabricate low-cost yet high-performance PLA-based composites for sustainable packaging application. [Display omitted] • A X O X (X = Si, Ti and Al) polycondensate coating was in-situ grafted onto the CNFs. • Ester chains in the coatings provided a mechanical interlocking with PLA chains. • A surface and interface engineering for sustainable PLA-based composites. [ABSTRACT FROM AUTHOR]

It has been a great challenge to prepare high-expansion-ratio polylactide (PLA) foam with eminent thermal insulation and compression performance in packaging field. Herein, a naturally formed nanofiller halloysite nanotube (HNT) and stereocomplex (SC) crystallites were introduced into PLA with a supercritical CO 2 foaming method to improve foaming behavior and physical properties. The compressive performance and thermal insulation properties of the obtained poly(L-lactic acid) (PLLA)/poly(D-lactic acid) (PDLA)/HNT composite foams were successfully investigated. At a HNT content of 1 wt%, the PLLA/PDLA/HNT blend foam with an expansion ratio of 36.7 folds showed a thermal conductivity as low as 30.60 mW/(m·K). Meanwhile, the compressive modulus of PLLA/PDLA/HNT foam was 115% higher than that of PLLA/PDLA foam without HNT. Moreover, the crystallinity of PLLA/PDLA/HNT foam was dramatically improved after annealing, thus the results showed that compressive modulus of the annealed foam increased by as high as 72%, while it still maintained good heat insulation with the thermal conductivity of 32.63 mW/(m·K). This work provides a green method for the preparation of biodegradable PLA foams with admirable heat resistance and mechanical performance. • The PLLA/PDLA/HNT composite foams with high expansion ratios were fabricated by scCO 2. • The thermal conductivity of PLLA/PDLA/HNT composite foams was as low as 30.60 mW/(m·K). • The annealing process further improved the compressive performance of PLLA/PDLA/HNT composite foams. [ABSTRACT FROM AUTHOR]