Search

This paper presents a fault diagnosis technique for high-resistance connection (HRC) in a nine-phase flux-switching permanent-magnet (FSPM) machine based on zero-sequence voltage components (ZSVC), where the neutral-point connection mode is considered. A nine-phase FSPM machine topology is first introduced and no-load back electromotive force waveforms are analyzed. Moreover, the topologies of the nine-phase FSPM drive with different neutral-point connection modes are studied. Then, the mathematical model of a nine-phase FSPM machine with HRC is established with the consideration of the neutral-point connection mode and then the influence of the HRC on the ZSVC is analyzed based on the established model. It is shown that the HRC may be diagnosed by monitoring the change of the spectral contents of the ZSVC. Furthermore, this paper focuses on the situation of the nine-phase FSPM machine with one neutral point. In this case, to remove the influence of the FSPM machine operating point, an effective fault indicator is defined and used for HRC fault detection. Finally, the simulation and the experiment are carried out to validate the proposed method. Both the results show that the proposed method can be applied for the HRC fault diagnosis in a nine-phase FSPM machine. [ABSTRACT FROM AUTHOR]

This paper develops an online interturn fault diagnosis method for permanent magnet synchronous machine (PMSM). The mathematical model of the PMSM with interturn fault is established. The zero-sequence voltage component and zero-sequence current component are analyzed in the PMSM, respectively. Then, the new fault indicators are defined to remove the influence of the variation of the rotor speed and an effective frequency tracking algorithm is presented to extract fault indicators. In this proposed method, not only the interturn fault can be effectively detected, but also the phase in which this fault occurs can be accurately identified. The experiments are carried out and the experiment results verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper explores the use of speed harmonic for accurate and fast maximum-torque-per-ampere (MTPA) control of interior permanent magnet synchronous machines (IPMSMs). A novel MTPA angle calculation approach is proposed, in which the MTPA angle is directly calculated from the phase angle of the speed harmonic that is induced by an injected harmonic current. At first, the relation between the speed harmonic and machine parameters is derived from the IPMSM model, which shows that the phase angle of the induced speed harmonic can be utilized to cancel the machine parameters in existing MTPA equation. Thus, a new MTPA equation is derived, which does not involve machine parameters for MTPA angle calculation. Compared with existing methods, the proposed approach is independent from the machine and drive nonlinearities. Moreover, the MTPA angle is directly calculated from the derived MTPA equation, so the proposed approach is fast and computationally efficient. Thus, the proposed approach is suitable for both on-line applications and building off-line lookup tables of MTPA angles for IPMSMs. The proposed approach is experimentally evaluated on a laboratory IPMSM drive system. [ABSTRACT FROM AUTHOR]

This paper proposes a method for online diagnosis and localization of high-resistance connection (HRC) in permanent magnet synchronous machine (PMSM) with an improved fault indicator. In the proposed method, the amplitude and initial phase angle of zero-sequence voltage component are both analyzed. Based on the analysis, the fault indicator with angle difference is defined for fault diagnosis and localization. It is shown that not only the HRC can be detected, but also the fault severity can be assessed and the faulty phases can be identified in this method. The simulation and experiment are carried out to verify the theoretical analysis. Both the results show that the proposed method can be effectively applied for online detection and identification of the HRC in the PMSM. [ABSTRACT FROM AUTHOR]

Dual-three-phase permanent magnet synchronous machines (DTP-PMSMs) are famous for their fault-tolerant capability. However, the complex modeling, high copper loss, and torque ripple under postfault operation limit their further application. In this article, a fault-tolerant control (FTC) strategy is developed for DTP-PMSMs under the open-phase fault (OPF) with straightforward modeling and smooth output torque. The virtual healthy DTP-PMSM model, where the coordinate transformation, the modulation strategy, and the controller structure remain unchanged under OPF, is adopted in the proposed FTC scheme. And the current references are derived in sinusoidal waves with minimum copper loss. The inaccurate transmission of control signals under OPF is also focused on. Comprehensive theoretical analysis shows the relationship between the controller output voltage and the actual stator voltage should be considered in the proposed FTC strategy; otherwise, distortion in torque and current will be introduced. The voltage compensation is utilized to compensate for the voltage difference and ensure the smooth torque output. Besides, a quasi proportional resonance controller is designed to further suppress the residual torque ripple. The proposed strategy will not induce complex implementation and heavy computation burden. The simulation and experimental results prove the analysis and the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

When multiphase drives are used for specific applications, the modular solutions are preferred as they use consolidated power electronics technologies. The literature reports two modeling approaches for multiphase machines having a modular configuration of the stator winding. The first approach is the vector space decomposition (VSD) that models the energy conversion as for an equivalent three-phase machine. The main alternative to the VSD is the multistator (MS) modeling that emphasizes machine modularity in terms of torque production. Both approaches have advantages and disadvantages for multiphase machines with a modular structure. Therefore, this article aims to combine the VSD and MS approaches, defining a new matrix transformation and, hence, developing a new modeling approach for multiphase machines with a modular structure. The proposed transformation allows a decoupled and independent torque control of the sets composing the machine, preserving the torque regulation's modularity. Together with a new vector control scheme, it has been applied to a modular permanent magnet synchronous machine (PMSM) with a nonstandard spatial shift between windings. Experimental results are presented for a nine-phase PMSM prototype with a triple-three-phase stator winding configuration. [ABSTRACT FROM AUTHOR]