Search

Japan Atomic Energy Research Institute is constructing the International Thermonuclear Experimental Reactor common test facility for the Central Solenoid Model Coil which is around 180 tons, a forced-flow cooled magnet with the maximum pulsed operation of 2 T/s and generates the rated magnetic field of 13 T at 48 kA with stored energy of 668 MJ. The test facility consists of a coil vacuum chamber, a cryogenic system with the 5-kW refrigerator and 500-g/s cryogenic pump, two pairs of 50-kA current leads, two DC power supplies (50kA and 60kA) and two JT-60 pulsed power supplies (50 kA, [+ or -]4.5 kV and [+ or -]40 kA, [+ or -]1.5 kV). The facility will be demonstrating the refrigeration and operation of a fusion pulsed magnet and the design and construction will accumulate experience towards the construction of ITER.

The [Nb.sub.3]Sn cable is being fabricated for the Central Solenoid (CS) Model Coil under the ITER Engineering-Design Activity. The cable consists of about 1000 strands whose diameter is 0.81 mm. The design current is 48 kA at a magnetic field of 13T. The 0.6-GJ CS model coil is operated in a pulse mode (0.5T/s). The first trial fabrication of a 100-m dummy cable and a 20-m superconducting cable was completed successfully. The second trial fabrication of a 1000-m dummy cable was performed to establish the stable manufacturing procedure in January, 1995. We measured the AC losses of the full-sized conductor and could determine the cable coupling time constant. We analyzed the heat generation of the CS model coil and calculated the temperature rise of the cable for the model coil.

The effect of cyclic pulsed operation on the coil performance was studied from the electrical and mechanical points of view in the second experiment of the [Nb.sub.3]Sn Demo Poloidal Coil (DPC-EX). Current sharing temperatures, ac losses, displacements, and strains were measured before and after cyclic pulsed operation, which consisted of about 350 cycles. No degradation of the electrical and mechanical performance of the DPC-EX was observed in the range of these cycles.

Japan Atomic Energy Research Institute (JAERI) has been developing 13-T, 40-kA conductors for the ITER Central Solenoid Scalable Model Coil. The conductors are composed of high performance [(NbTi).sub.3]Sn strands and titanium conduit. In this development work, 15-km length strand fabrication from a 100-kg billet, chrome plating, cabling of 675 or 768 strands, jacketing of titanium conduit, and so on were conducted by two mass production lines. In this paper, several test results are reported such as critical current measurements of full-scale conductors and AC loss measurements of sub-scale conductors.

Micrometer thick [Bi.sub.3][Fe.sub.5][O.sub.12] (BIG)(001) films were grown onto [Gd.sub.3][(ScGa).sub.5][O.sub.12](001) single crystals by the pulsed laser deposition technique. The films are of epitaxial quality with a lattice constant of 1.263 nm. Narrow x-ray rocking curves (full width at half maximum: 0.06 deg) and narrow ferromagnetic resonance lines (widths of 25 Oe) indicate good crystalline quality and magnetic performance. The films possess in-plane magnetization, Faraday rotation as high as -7.8 deg/[micro]m at 630 nm wavelength, and the magnetization M-H curves are linear in the field range from -1.6 kOe to -1.6 kOe. The magneto-optical (MO) properties are almost temperature independent between 5 K and 200 K. This enables the use of thin BIG films as visualizers of magnetic fluxes in high-[T.sub.c] superconductors. Magnetic fluxes have been visualized in [YBa.sub.2][Cu.sub.3][O.sub.7-x] (YBCO) ceramics with an artificial grain boundary. The sensitivity expressed as Faraday rotation angle (per film thickness) per magnetic field unit was found to be 4.9 deg/(kOe [multiplied by] [micro]m) in a 730 nm thick BIG film. Index Terms--Epitaxial [Bi.sub.3][Fe.sub.5][O.sub.12] film, Faraday effect, pulsed laser deposition, visualizer.