Search

Large power consumers often have on-site generation. If the utility tie opens, it is essential to isolate the on-site generators to prevent generator equipment damage before the utility attempts to reclose in a possible out-of-synchronism condition. Typically, islanding detection schemes are used to detect this condition and disconnect on-site generation quickly, thereby allowing successful utility reclose. This paper introduces a reliable islanding detection solution that was proposed, implemented, and tested at a refinery in Texas. The facility houses two on-site generators and is interconnected to the utility via a looped system. A topology-based islanding detection scheme was originally installed at this facility but was later decommissioned because of difficulties in adapting to evolving topology changes. Following an undesirable event in the utility system that could have resulted in damage to the refinery on-site generator equipment, the refinery decided to implement an islanding detection scheme that is independent of system topology changes and only relies on local-area measurements. However, the dependability of a traditional local measurement-based scheme is vulnerable to the dynamic generation–load mismatch, making it possibly unreliable. This paper describes a solution using a redundant high-speed multiprinciple islanding detection scheme that incorporates a unique voting supervision logic to achieve security. [ABSTRACT FROM AUTHOR]

In addition to market information, available energy and capacity to participate in the market are also essential to be an effective market participant. This paper discusses the development of an online dynamic cable rating system (DCRS) that can help a system engineer maximize asset utilization without jeopardizing system facilities or compromising the reliability of the cables. Based on real-time cable loading, cable surface temperature, ambient temperature, and forecasting temperature, the DCRS can estimate both steady-state and dynamic cable rating. To confirm with the actual operation condition, both real-time cable temperature and forecasting ambient temperature are taken into consideration to perform short-term cable ampacity estimation to prevent overestimation and/or underestimation. Based on the information provided by the DCRS, the system engineer can establish or adjust the bidding strategy in time to effectively participate in the restructured electric markets. [ABSTRACT FROM AUTHOR]

This article presents the modeling, design, and control of a photovoltaic supply (PVS) for single-phase grid system. In the two stage conversion process, a step-up converter (SUC) is employed in between the photovoltaic panel and dc bus of voltage source converter (VSC). For the maximum power tracking (MPT) at PVS terminals, a fuzzy logic control (FLC) based approach is developed for the switching of an SUC. A band-pass filter (BPF) is developed using modified multilayer fifth-order generalized integrator (mMLFOGI) to estimate synchronizing signals of the grid supply for the control of VSC. The mMLFOGI based BPF ensures the proper synchronization of VSC under grid disturbances such as dc offsets, frequency variations, voltage sag, swell, and harmonics. These proposed control approaches are simulated in MATLAB 2018a and prototype of PVS for single-phase grid system is developed in the laboratory. A Texas instrument micro controller board TMS320F28379D is used for real time validations of proposed control algorithms. The performance is obtained using simulation model and validated with test results under field emulated conditions. [ABSTRACT FROM AUTHOR]

The large-scale integration of distributed photovoltaic generation causes several power quality issues in low voltage (LV) distribution networks. Network voltage profile variations severely affect the LV distribution networks. The four-leg unified power flow controller (4L-UPFC) has series and shunt converters that can address the power quality issues. However, instantaneous power theory shows that second-order harmonic voltage (2ωHV) appears at the dc-link capacitor of the 4L-UPFC during any unbalanced operations. This article proposes control strategies for series and shunt converters that will simultaneously regulate the load voltages of a distribution feeder while suppressing the 2ωHV term on the dc-link of the UPFC. A controlled negative sequence current from the shunt converter is used to suppress the 2ωHV term on the dc-link. The active suppression of the 2ωHV term allows electrolytic capacitors to be replaced with small long life ceramic or film capacitors, and this does not require additional passive compensation. Stability analysis of the control loops demonstrates the overall stability of the converter system. The proposed control methods have been implemented on a Texas DSP (F28377D). An experimental demonstration on a laboratory scale prototype shows that the proposed control methods can effectively regulate the load voltages at LV distribution feeders and suppress the 2ωHV on the dc-link of UPFC during unbalanced loads and supply conditions. [ABSTRACT FROM AUTHOR]

Frequency scanning is a powerful and versatile approach for subsynchronous resonance (SSR) screening in power grids. Among different numerical and analytical frequency scanning techniques, the harmonic injection method is well suited for the scan of black-box models with active elements, such as in wind farms and solar plants. The results can be used for SSR risk assessment, in which accuracy performs a decisive role. The ideal situation for this method, which leads to the most accurate results, is to perform one simulation per single-frequency injection. However, for SSR studies with a wide range of frequencies and simulations with very small time steps (scale of μs), this comes at the expense of increased simulation time. This article proposes a technique to improve the accuracy of the harmonic injection method through the optimization of the crest factor while injecting all frequencies at one shot, therefore also reducing simulation time. The proposed technique was tested on a wind farm connected to a radial test case and on a portion of a Texas synthetic grid with multiple active elements, including two wind farms and a VSC-based STATCOM. The frequency scan results were benchmarked with both time-domain transient simulations and the ideal multiple single-frequency injection case and compared with other techniques. The results show that the proposed method is superior in accuracy when compared to the other techniques and is 11.71 times faster when compared to multiple single-frequency injections. [ABSTRACT FROM AUTHOR]