Search

Saturation characteristics of water and capillary pressure are important for hydrofracturing or water flooding, which is widely adopted in dust suppression, methane displacement, and gas and coal outburst elimination. In this paper, we have studied the water saturation characteristics of coal samples with different coal ranks and their effect on capillary pressure. It was found that the isothermal adsorption of water vapor from coal samples can be divided into three processes: monolayer adsorption, multilayer adsorption, and capillary condensation. The dent isothermal adsorption model can well describe water vapor adsorption of coal samples, indicating water molecules were first adsorbed on the first‐order adsorption site of pore surfaces at low relative humidity and then on the second‐order adsorption site with increasing relative humidity. An obvious hysteresis occurred in the process of water imbibition and drainage. A capillary pressure of ~325 MPa or even larger was required to displace the water from the coal. Besides, micro‐ and mesopores play a more important role in capillary pressure. The capillary pressure of coal samples was positively correlated with wettability at lower water saturation, but it is not significant at higher capillary pressures. Therefore, the article's results provide a new direction for solving the water‐locking effect in coal seams. [ABSTRACT FROM AUTHOR]

Coal deformation caused by gas adsorption is a well‐known phenomenon and has played an important role in many engineering fields. For example, the bulk coal deformation induced by gas is a primary factor in coal and gas outbursts, and the changes in coalbed permeability are primarily determined by the evolution of the coal fracture volumetric strain during gas recovery. However, the current models of coal deformation induced by gas do not fully consider the coal seam field conditions or the deformation factors. To better fit coal seam field conditions and provide a basis for engineering applications, in this work, based on coal's physical structure, coal seam field conditions, the energy balance approach, poroelasticity, mathematical differentiation, and previous scholars' research results, the volumetric strain models of bulk coal, coal fracture, and coal matrix under coal seam field conditions are established. In addition, based on the analysis of the effect of gas pressure on coal deformation, the difference in gas pressure effects on the bulk coal deformation between experimental conditions and coal seam field conditions revealed that when the bulk coal deformation is tested in a laboratory, the gas pressure exerts a compressive effect on the bulk coal. However, under coal seam field conditions, the gas pressure has a swelling effect on the bulk coal. Additionally, gas pressure exerts an compression on the coal matrix and a swelling on the coal fracture under coal seam field conditions. At the end of the paper, the established models were analyzed and discussed from multiple perspectives. It was shown that the coal deformation models established in this paper are all accurate and reliable. [ABSTRACT FROM AUTHOR]

Protective coal layer (PCL) mining is a preferred regional method for preventing coal and gas outbursts; stress‐relief of PCL mining is the prerequisite of pressure‐relief gas drainage. In order to study the stress‐relief effect of PCL mining on protected coal seams and determine the protection scope of PCL mining under different inclinations, this paper uses physical simulations to study the stress‐relief law and deformation characteristics of the strata during upper PCL mining with a gentle inclination (25°), an intermediate inclination (45°), and a steep inclination (65°). The results show that as the coal seam dip increases, the degree of deformation and failure of the overburden strata gradually decreases, the severe subsidence and expansion area of the overburden strata tends to gradually develop in the uphill direction of the working face, and the floor strata underlying the protective seam significantly expand toward the goaf. However, the absolute value of the upward movement of the floor strata is much smaller than that of the roof strata; and the greater the dip angle, the greater the ratio of floor displacement to roof subsidence. The stress‐relief curve of the protected layer is approximately U‐shaped. As the inclination of the coal seam increases, the stress‐relief range decreases gradually. The maximum relief‐stress and the stress release coefficient of the protected layer initially increase and then decrease. The stress concentration coefficient of the protected coal seam initially increases first and then decreases in both uphill and downhill of the working face in the PCL. As the inclination increases, the stress‐relief angle of the downhill boundary initially increases and then decreases, while the stress‐relief angle of the uphill boundary decreases gradually. Our research results provide guidance for the delimitation of the protected scope of PCLs with different dip angles. [ABSTRACT FROM AUTHOR]

The revelation of the distribution characteristics of stress and fractures in the floor strata is of great significance to improve the regional gas drainage efficiency and to eliminate or reduce the risk of coal and gas outburst in adjacent coal seams during multi‐seam mining. In this paper, the stress distribution in the floor under mining condition was derived, and the characteristics of stress zones in the floor were elaborated while mining the 22201 working face in Shaqu coal mine in Shanxi province, China. Besides, the propagation laws of fractures in different stress zones were theoretically analyzed, and the distribution law of fracture angles in the floor strata under different mining‐induced stresses was obtained. The research results demonstrate that the compression and transition zones show high vertical stress and less developed fractures and are dominated by fractures with a large angle (>60°), which is unfavorable for gas drainage. The expansion zone in the floor within 2‐40 m in the rear of the working face is characterized by high unloading degree of vertical stress and developed fractures. Moreover, fractures with a small angle (<60°) dominate the spatial distribution of the fractures, which is favorable for gas drainage. The research results can not only be a beneficial supplement to the theory of coal and gas co‐exploitation in multi‐seam mining but also provide theoretical support for optimizing the design parameters of cross‐measure boreholes under similar conditions. [ABSTRACT FROM AUTHOR]

Coal and gas outburst is a potentially fatal risk during the mining of gassy coal seams, which seriously threatens the safe mining of collieries. To understand the outburst mechanism and evolution rules, a new apparatus (LSTT) was developed to conduct simulated experiment. In the context of an outburst accident in Dingji coal mine, the authors launched an authentic outburst experiment to replay the outburst accident. Experimental apparatus, similar criterion, coal‐like materials and gas sources, and experimental design were discussed systematically in this paper. Experimentally, the study analyzed the geo‐stress has significant influence on the outburst evolution. At the driving face, the stress concentration possibly caused gas outburst, under the influence of mining‐induced stress. After the outburst occurred, the stress balance of the coal changed, resulting in the instability of the coal. Furthermore, the elastic energy, gas enthalpy, and gravitational potential energy were released rapidly. The experimental result stated that outburst coal has the sorting characteristics, in line with the field outburst law. The intensity prediction model has been built based on the energy model. Moreover, the factors that impact outburst intensity were analyzed. In the process of coal and gas outburst, the gas enthalpy of gas and the elastic potential of coal are the main energy sources. This study provides guidance for the development of the outburst mechanism and outburst mine management. [ABSTRACT FROM AUTHOR]

Gas pressure is one of the major factors to characterize the outburst danger of coal seams. Generally, the process of gas pressure determination is complicate and cannot ensure the accuracy of results, which may cause a wrong identification of outburst danger. This paper discussed and revealed a positive correlation between initial gas emission and gas pressure, which provides a new approach to identify the outburst danger by initial gas emission. Through theoretical analysis and numerical simulation, the liner equation of gas pressure and initial gas emission was deduced. Laboratory experiments under adsorption and desorption of CO2 and N2 were performed using coal samples from Weishe coal mine. The data of initial gas emission under different gas pressure were recorded, and the fitting curves were obtained. The results show a positive correlation between initial gas emission and gas pressure, and the curve of N2 was below the CO2. Especially, while the adsorption gas pressure was under 0.663 and 0.675 MPa, the difference of corresponding initial gas emission was only 0.01 L/s, which indicates the high degree of correlation. The results validated the theoretical and practical feasibility to identify the coal and the gas outbursts through initial gas emission. [ABSTRACT FROM AUTHOR]

In recent years, with the increase in mining depth and strength, coal‐rock gas dynamic disasters, such as coal and gas outburst, have shown an increasing trend. Acoustic emission (AE) technology has been viewed as a promising method that can effectively forecast coal and gas dynamic disasters. This paper first tests the AE characteristics of coal and rock samples during loading. Then, self‐developed AE continuous monitoring and early warning equipment is used to monitor and predict the coal and gas outburst dynamic disasters on the working face. And it is found that the coal samples primarily show ductile failure, and the AE exhibits the evolutionary characteristics of "rise‐peak‐fall". The rock samples primarily exhibit brittle failure, and the AE evolution mode is almost no falling stage. Coal and gas outbursts occur after the stress peak. Before coal and gas outbursts occur, there is a clear increasing trend in the AE ahead of the gas concentration variation. When the gas‐bearing coal is damaged by the load, the coal body first breaks due to the stress, and the AE value increases. Then, due to the fracture of the coal body, the crack penetrates, gas rushes out, and the gas concentration increases. The research results can provide an advanced technical method for the monitoring and early warning of coal–rock gas dynamic disasters, and improve the prediction accuracy for dynamic disasters. The AE exhibits the evolutionary characteristics of "rise‐peak‐fall"; the rock sample exhibits brittle failure, and the AE evolution mode lacks the "decline" stage. There is a clear increasing trend in the AE before the gas concentration variation and accidents. When the coal‐containing gas is damaged by the load, the coal body first breaks due to stress, and the AE value increases. [ABSTRACT FROM AUTHOR]

Gas outbursts pose a significant threat in the mining of deep low‐permeability coal seams. As mining depth increases, there is a rise in coal and gas dynamic disasters, rendering the gas outburst prevention technology from shallow mining areas unsuitable for deep coal seam exploitation. Addressing the challenges posed by deep, highly gassy coal seams, this study introduces a gas outburst prevention technology integrating destressing in the close distance underlying roadway with gas drainage. The article investigates the relevant technical parameters and assesses the feasibility of this approach. First, it establishes destressing model for the underlying roadway to derive an analytical solution for stress distribution in the coal seam. Second, appropriate technical parameters are designed considering the seepage characteristics of gas in the coal seam. Finally, the gas drainage technical scheme is implemented at Qujiang coal mine to verify its on‐site effectiveness. Field test results indicate an increase in gas permeability within the coal seam following destressing in the underlying roadway, accompanied by significant improvements in the efficiency of gas drainage and the advancement speed of the coal roadway. Specifically, the driving speed of the coal roadway has escalated from 40 m/month to 150 m/month. These outcomes demonstrate the potential of this technology as a promising approach for preventing gas outbursts in the challenging context of deep, low‐permeability coal seams, facilitating swift coal roadway excavation. [ABSTRACT FROM AUTHOR]

Any disturbance in the ventilation system of a mine during a coal and gas outburst can lead to secondary disasters. This is because, on the one hand, the expansion power of the outburst source makes the airflow in the ventilation system countercurrent, causing the gas in this system to exceed the allowable limit. On the other hand, the airflow density changes because of the outburst and the consequent airflow mixing in the mine roadway, thereby changing the natural wind pressure. From this, the concept of natural gas wind pressure is proposed, and a calculation method for this pressure in a 3D model mine ventilation system is derived. For the "11.10" major coal and gas outburst that occurred in Shizhuang Coal Mine in Qujing, Yunnan Province, the entire process of the counter flow and gas dispersion flow in the main and auxiliary shafts is analyzed using the TF1M 3D simulation program, including the dynamic change in the natural wind pressure in the mine in each stage. The simulation shows that during the gas outburst period, the natural gas pressure of the countercurrent circuit is greater than that of the main fan. Between 140 s and 225 s following the outburst, the natural wind pressure once overcomes the fan pressure and reverses the airflow in the 1824 transport roadway, and the gas is withdrawn from the 1727 service point. Evidently, the natural pressure of the gas produced by the outburst affects the mine ventilation system. In the event of a coal and gas outburst in a private village coal mine, if the natural gas wind pressure can be reasonably utilized and the main fan stopped or the entire mine reversed in time, casualties may be minimized. Scholars studying coal and gas outburst mines should pay attention to mine airflow disorder due to the varying natural gas wind pressure when an outburst occurs and perform simulation drills of the outburst beforehand. Thus, a scientific emergency management plan for mine disaster prevention and reduction can be formulated. [ABSTRACT FROM AUTHOR]

The high‐pressure gas expansion‐induced deformation and dynamic fracture of coal are important parts of coal and gas outburst. To better understand the law of this process, laboratory experiments and numerical simulation are used to study the law of damage. A cavity with different pressures of CH4 or N2 was destroyed by a jack to achieve the rapid expansion of the gas and coal fracture inside. The particle size distribution of the coal particles before and after the experiment was measured, and the breakage ratio and the newly added surface area were calculated. The experimental results indicate that during the gas expansion process, the breakage ratio of coal and the newly added surface area clearly increase with the increase in gas pressure. Finally, a numerical model based on peridynamic theory was developed to simulate crack generation and the propagation of coal induced by the expansion of gases at different pressures. The numerical simulation results show that the higher the initial gas pressure is, the higher the number of failure units. Moreover, only when the gas pressure is large enough will the coal crack in various directions at the same time. [ABSTRACT FROM AUTHOR]

Coal and gas outburst is one of the most harmful natural disaster in coal mine production. The frequency and scope of outburst are closely related to the metamorphic degree of coal seam, the depth of coal seam, and the complexity of geological structure. In general, the use of traditional along‐seam borehole or cross‐seam borehole can meet the needs of gas control. However, for the coal seams with high outburst risk, these methods fail to meet the demands of high‐yield and high‐efficiency coal recovery as well as safe, green, and economical coal mining. Although pressure‐relief gas extraction in the protective seam and coalbed methane (CBM) pre‐extraction can eliminate outburst risk in coal seams, these methods can hardly help realize the green development trend of coal and CBM co‐extraction because they cannot guarantee the current situation of highly mechanized mining. In this study, a three‐dimensional coal and CBM co‐extraction strategy was proposed. The strategy includes three levels of three‐dimensional gas prevention and control methods. The first level is the combination of ground and underground gas extraction methods, to achieve joint extraction of ground and underground gas. The second level is the full‐coverage extraction of the coal resources to be mined, to achieve joint extraction through upper and lower cross‐seam borehole and along‐seam borehole. The third level is the optimization of ground and underground extraction and utilization systems, to realize the full utilization of CBM and to achieve the goal of coal and CBM co‐extraction. The three‐dimensional gas prevention and control method constructs a new gas control model for single thick coal seams with high gas outburst risk and realizes the all‐round coordination and unity of different gas control methods spatially and temporally. The gas control strategy completely eliminates the high gas outburst risk of a single thick coal seam and has been successfully applied in Hudi Coal Mine. The application results verify that the method can effectively guarantee the operation safety during highly mechanized mining, realize extraction and full utilization of separate‐source gas, and provide guidance and direction for coal and CBM co‐extraction with similar extraction conditions. [ABSTRACT FROM AUTHOR]

Gas distribution ahead of the coal tunnel is the key risk factor controlling coal and gas outburst. Based on an analysis of the influence of the stress state on the porosity of the coal seam, an improved quartet structure generation set (QSGS) random porous media generation tool is used to reconstruct the coal structure. Adopting the reconstructed pore structure of the coal as the boundary of the flow field, the Lattice Boltzmann method (LBM) is used to simulate the gas dynamic distribution law ahead of the coal tunnel. The gas pressure of the coal seam decreases obviously in the fracture zone only, and the change in gas pressure is very small in the stress concentration zone and ahead of the coal seam. This research is of significance for gas drainage and the prevention of coal and gas outburst hazards in the working face during coal tunneling. [ABSTRACT FROM AUTHOR]

Predrainage of gas by cross‐boreholes is an important method to prevent coal and gas outbursts in the process of a coal roadway excavation. Limitations of technologies and poor effects of preventing coal and gas outbursts occur in the coal seam with a soft layer. In this study, a new hydraulic caving technology for cross‐boreholes has been proposed to solve this problem. A CT equipment was used to observe the development of coal fissures around cross‐boreholes in the coal seam with a soft layer. The plastic zone range and permeability distribution of ordinary hydraulic slotting technologies and the new hydraulic caving technology also were compared by numerical simulation. The field test of hydraulic caving was taken in the Xuehu Mine (China). The results show that the fracture development degree of soft coal is greater than that of hard coal at the same distance from cross‐boreholes. The fracture development degree in the plastic zone is greater than that in the elastic zone. The hydraulic caving technique can achieve the same effect as the ordinary hydraulic slotting with less workload. The mass of coal discharged from a cross‐borehole was 1.15 t/m and the average methane concentration of single drainage borehole increased by 1.09‐4.1 times, and the average methane extraction amount of single drainage borehole increased by 6.06 times. Elimination of coal and gas outburst had been completed after 110 days of extraction in the area of hydraulic caving, and Q and S values are lower than the critical value during roadway excavation. It is conclusion that hydraulic caving technique can effectively improve the permeability and rapidly eliminate coal and gas outburst in the coal seam with a soft layer. [ABSTRACT FROM AUTHOR]

We report laboratory experiments to investigate the dynamic failure characteristics of outburst‐prone coal using a split Hopkinson pressure bar (SHPB). For comparison, two groups of experiments are completed on contrasting coals—the first outburst‐prone and the second outburst‐resistant. The dynamic mechanical properties, failure processes, and energy dissipation of both outburst‐prone and outburst‐resistant coals are comparatively analyzed according to the obtained dynamic compressive and tensile stress‐strain curves. Results show that the dynamic stress‐strain response of both outburst‐prone and outburst‐resistant coal specimens comprises stages of compression, linear elastic deformation, then microfracture evolution, followed by unstable fracture propagation culminating in rapid unloading. The mechanical properties of both outburst‐prone and outburst‐resistant coal specimens exhibit similar features: The uniaxial compressive strength and indirect tensile strength increase linearly with the applied strain rate, and the peak strain increases nonlinearly with the strain rate, whereas the elastic modulus does not exhibit any clear strain rate dependency. Differences in the dynamic failure characteristics between outburst‐prone and outburst‐resistant coals also exist. The hardening effect of strain rate on outburst‐prone coal is more apparent than on outburst‐resistant coal, which is reflected in the dynamic increase factor at the same strain rate. However, the dynamic strength of outburst‐prone coals is still lower than that of outburst‐resistant coals due to its low quasi‐static strength. The dissipated energy of outburst‐prone coal is smaller than that of outburst‐resistant coal. Therefore, the outburst‐prone coal, characterized by low strength, high deformability, and small energy dissipation when dynamically loaded to failure, is more favorably disposed to the triggering and propagation of gas outbursts. [ABSTRACT FROM AUTHOR]

To further more deeply understand the influence of cyclic loading‐unloading on coal seams during mining and reduce the rock burst and coal and gas outburst disasters and ensure safety during coal mining, triaxial cyclic loading‐unloading tests were performed on coal samples. The permeability recovery rate, residual deformation, and dissipated energy ratio were defined to analyze the evolution in the characteristics of permeability, deformation, and energy observed during the triaxial cyclic loading‐unloading test. The results show as following: (a) The absolute permeability recovery rate first gradually decreases and then increases before failure, while the relative permeability recovery rate decreases sharply during the compaction stage, remains stable during the elastic phase, and gradually increases before failure; (b) The cumulative residual deformation increases with increase number of cyclic loading‐unloading, while relative residual deformation first decreases gradually, then stabilities, and then rises sharply before failure; (c) With increases in deviatoric stress, the total energy of coal samples increased as an exponential function. The dissipated energy ratio gradually decreased in the initial stages of cyclic loading‐unloading, then tended to stabilize in the elastic stage and then increase gradually before failure. This study provides precursor conditions for the early warning of rock burst and coal and gas outburst disasters, which has great importance for reducing coal mine dynamics disasters. [ABSTRACT FROM AUTHOR]

Coal and gas outburst disasters are prone to occur within rock cross‐cut coal uncovering in deep underground coal mines. To reduce the risk of coal and gas burst under rock cross‐cut coal uncovering, a technique of permeability enhancement using hydraulic fracturing sand‐carrying is proposed. Field test was conducted using HF sand‐carrying approach, and the effect of permeability enhancement was investigated. The results show that the evolution of cracks has been subjected three stages: energy slowly increasing and crack initiation, damage localization of coal seam and gradually failure, and crack instability expansion and formation of a complex fracture network system. In addition, it is found that "water‐sand" type injection of high‐pressure fluid carried sand into HF cracks, which creates a support force on crack surface and prevents crack closure. A fully developed fracture network system with high flow conductivity capacity is created and thus increases gas permeability largely. Furthermore, a clearly increasing trend associated with the HF sand‐carrying is found for the treated coal seam area. The permeability coefficient is about 21.5‐30.5 times higher than that from the raw coal seam. A good prevention effect of coal and gas outburst is achieved using HF sand‐carrying method. [ABSTRACT FROM AUTHOR]

Coal seams in China are mainly characterizsed by low permeability and high risk of coal and gas outburst. Therefore, the elimination of coal and gas outburst risk of low‐permeability coal seam remains a hard challenge. Taking Shihuatian Coal Mine in Guizhou Province, China as an example, boreholes were slotted using high‐pressure water jet to relieve the gas pressure inside the coal seam and increase the permeability of coal mass, which thus improves the gas drainage efficiency and eliminate the outburst risk. The results show that the gas drainage efficiency of the slotted boreholes significantly increases. Compared with the conventional boreholes, the average gas concentration and flow velocity improved by 1.6 and 7.5 times, respectively. Moreover, the prediction index of outburst risk is less than the critical value after high‐pressure water jet slotting, which indicate that the coal and gas outburst risk has been effectively eliminated. The measured values of gas desorption index of drilling cuttings are all lower than the critical value after the application of the high‐pressure water jet slotting technology. The research achievements could provide a practical reference for the effective gas disaster prevention and control in low‐permeability coal seams. [ABSTRACT FROM AUTHOR]

Based on the Langmuir adsorption model, the adsorption constants of eighteen coal samples from the same coal mine with outburst risk, weak outburst risk, and non‐outburst risk were tested by high‐pressure capacity method under different temperature conditions. The results show that the adsorption constants a and b monotonically decrease with the increase in temperature. The relationship between a and temperature shows three stages: accelerated decreasing stage, decelerated decreasing stage, and stable stage. The b decreases with the increase in temperature also shows three stages, namely relative stability, slow decrease, and accelerated decrease. The a × b for the outburst coal seam decreases with increasing temperature, which is similar to b. The a × b for the weak and non‐outburst coal seams decreases with increasing temperature, which is similar to a. Furthermore, the a of the outburst coal seam decreases with the increase in temperature, and the decrease of b is the largest. The a of the weak and non‐outburst coal seams decreases with the increase in temperature, and the magnitude is relatively large. The b decreases slightly, with a smaller magnitude. The a × b of weak outburst seam is smaller than that of non‐outburst seam and is larger than that of outburst seam. The achievements can provide guiding significance for coal and gas outburst prevention and control. [ABSTRACT FROM AUTHOR]