Search

In this paper, the aging characterization of a kind of insulating paper modified by magnetron sputtering MgO particles based on a microstrip resonant sensor was presented. Firstly, the modified insulating paper with 0, 15 and 30 min MgO particle sputtering times was prepared by a magnetron sputtering device. After that, the properties of the modified insulating paper with different sputtering times were analyzed through microscopic characterization, infrared spectrum, polymerization degree, dielectric constant, AC breakdown strength and thermal aging experiments. The results show that the dielectric constant of the modified insulating paper decreased obviously, the AC breakdown strength increased and the thermal aging resistance was better after 15 min of sputtering. The overall performance of the modified insulating paper after 30 min of sputtering is reduced due to excessive sputtering. In addition, microstrip resonant sensors are introduced to characterize the thermal aging degree of the modified insulating paper, and two microstrip resonant sensors are prepared: a complementary split ring resonator (CSRR) and an interdigital-capacitor-shaped defected ground structure resonator (IDCS-DGS). The resonance frequency deviation of the modified insulating paper samples after aging was measured by microstrip resonance sensors to show the influence of aging temperature on aging degree. The experimental results show that the test results of the microstrip resonance sensors are in good agreement with the traditional characterization methods and can characterize the various aging stages of the modified insulating paper to a certain extent, which proves the feasibility of the characterization method. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is under increasing pressure to reduce its energy consumption and carbon footprint. This study examines the feasibility of integrating high-temperature heat pumps (HTHP) into tissue paper production to enhance energy efficiency and decarbonization. Focusing on the energy-intensive drying process, the study uses data from a typical tissue paper mill to simulate and optimize an HTHP system producing four tons per hour of nine-bar saturated steam. It also addresses necessary modifications for HTHP integration applicable across the sector. Various refrigerants were analyzed, achieving a maximum coefficient of performance (COP) of 2.01. Results showed that HTHP can reduce energy consumption and emissions by up to 17% and 40%, respectively, based on the European electricity mix. Although steam production costs increase by 55% compared to fossil fuel-based systems, HTHP is more cost-effective than direct electric resistance heating, which raises costs by 196%. With a CO2 price of EUR 100/t, HTHP offers a 12% cost reduction. However, without public funding, capital expenditures may be unsustainable in many regions, though viable in countries with favorable gas and electricity price differentials. The paper underscores the need for advancements in HTHP technology and cost reductions, emphasizing industry adaptation for seamless HTHP integration. [ABSTRACT FROM AUTHOR]

Oil–paper insulation is the critical insulation element in the modern power system. Under a harsh operating environment, oil–paper insulation will deteriorate gradually, resulting in electrical accidents. Thus, it is important to evaluate and monitor the insulation state of oil–paper insulation. Firstly, this paper introduces the geometric structure and physical components of oil–paper insulation and shows the main reasons and forms of oil–paper insulation's degradation. Then, this paper reviews the existing condition assessment techniques for oil–paper insulation, such as the dissolved gas ratio analysis, aging kinetic model, cellulose–water adsorption isotherm, oil–paper moisture balance curve, and dielectric response technique. Additionally, the advantages and limitations of the above condition assessment techniques are discussed. In particular, this paper highlights the dielectric response technique and introduces its evaluation principle in detail: (1) collecting the dielectric response data, (2) extracting the feature parameters from the collected dielectric response data, and (3) establishing the condition assessment models based on the extracted feature parameters and the machine learning techniques. Finally, two full potential studies are proposed, which research hotspots' oil–paper insulation and the electrical–chemical joint evaluation technique. In summary, this paper concludes the principles, advantages and limitation of the existing condition assessment techniques for oil–paper insulation, and we put forward two potential research avenues. [ABSTRACT FROM AUTHOR]

The aim of this research is to predict the mechanical properties along with the behaviors of standard insulating paper used in power transformers under thermal aging. This is conducted by applying an artificial neural network (ANN) trained with a multiple regression model and a particle swarm optimization (MR-PSO) model. The aging of the paper insulation is monitored directly by the tensile strength and the degree of polymerization of the solid insulation and indirectly by chemical markers using 2-furfuraldehyde compound content in oil (2-FAL). A mathematical model is then developed to simulate the mechanical properties (degree of polymerization (DPV) and tensile index (Tidx)) of the aged insulation paper. First, the datasets obtained from experimental results are used to create the MR model, and then the optimizer method PSO is used to optimize its coefficients in order to improve the MR model. Then, an ANN method is trained using the MR-PSO to create a nonlinear correlation between the DPV and the time, temperature, and 2-FAL values. The acquired results are assessed and compared with the experimental data. The model presents almost the same behavior. In particular, it has the capability to accurately simulate the nonlinear property behavior of insulation under thermal aging with an acceptable margin of error. Since the life expectancy of power transformers is directly related to that of the insulating paper, the proposed model can be useful to maintenance planners. [ABSTRACT FROM AUTHOR]

To eliminate the problem of the aging of cellulose insulation in the manufacturing stage, a new drying method is being developed based on the use of methanol vapors. Previous studies have shown that the complete removal of methanol from the cellulose insulation after the drying process is very difficult. Therefore, it is necessary to check how the remaining methanol after drying affects the properties of both the cellulose materials and mineral oil. To conduct such studies, it is necessary to know the methanol content in oil that can be expected depending on its initial content in the cellulose materials and the temperature of the insulation system. Therefore, the main goal of this work is to develop methanol equilibrium curves for oil–paper insulation. To achieve the assumed goal, three-stage studies were conducted. A gas chromatograph equipped with a flame ionization detector was used in all stages of these studies. The gas partition coefficient between oil and air was determined for a temperature of 70 °C. The key experimental finding was the development of methanol equilibrium curves for oil–paper insulation. Thanks to this achievement, it is possible to estimate the methanol content in cellulose materials and mineral oil depending on the insulation temperature. Such data are necessary, among others, to plan appropriate studies aimed at assessing the impact of methanol content on the dielectric and physicochemical properties of these materials, important from the point of view of the operation of power transformers. [ABSTRACT FROM AUTHOR]

In order to reveal the migration and evolution of gas molecules in the actual oil–paper insulation composite system of transformer from the molecular level, the diffusion behavior of seven gas molecules (H2, CO, CO2, CH4, C2H2, C2H4, C2H6) generated during the operation and aging of oil-immersed transformers in the oil–paper composite insulation system is studied by molecular dynamics. Firstly, based on the molecular dynamics software, the model of the oil–paper composite insulation system and the gas molecule model is constructed. In order to compare and analyze the diffusion properties of gas molecules in a single medium, a single model of insulating oil and cellulose is also constructed. Then, the diffusion coefficients of gas molecules in the insulating oil, cellulose, and oil–paper insulating composite system are simulated and calculated. And the differences in the diffusion properties of gas molecules in the three insulating mediums are discussed. Finally, the microscopic mechanism of diffusion of different gas molecules in the three mediums is analyzed. The simulation results show that among the three mediums, the diffusion coefficient of H2 is the largest, while the diffusion coefficients of the other gas molecules are not very different. The diffusion coefficients of the seven gas molecules are the smallest in the oil-immersed paper composite insulation system, followed by cellulose, while the diffusion coefficients are the largest in mineral oil. It indicates that the diffusion of gas molecules is inhibited in oil–paper insulation systems where the insulating paper is completely immersed in oil. This is mainly due to the fact that the insulating oil completely penetrates into the paper, filling the pores and voids between the fibers, resulting in a reduction in the transition vacancies of the intermediate gas molecules, which hinders the diffusion of the gas molecules. [ABSTRACT FROM AUTHOR]

Chemical compounds dissolved in insulating oil, as indicators can excellently monitor the paper aging condition, which has attracted increasing interest in areas of transformer condition monitoring and fault diagnosis. Because of their outstanding features, such as good correlation with the degree of polymerization of cellulose paper and the aid of non-destructive online monitoring, chemical indicators have been effectively used for transformer condition assessment. In this study, a comprehensive, in-depth insight into the indicators of the aging of insulating paper from aging characteristics, physico-chemical characteristics, shortcomings of various compounds, generation pathways and mechanisms, and monitoring technologies are provided. It is expected that these chemical indicators can provide better guidance for the evaluation of paper insulation performance and transformer aging. In addition, the latest research progress, as well as current challenges and future prospects are also outlined. This study provides a theoretical basis and reference for chemical indicators in the fields of microscopic formation mechanism, diffusion equilibrium phenomenon, and insulation aging state assessment. [ABSTRACT FROM AUTHOR]

The pulp and paper industry (PPI) has several opportunities to contribute to meeting prevailing climate targets. It can cut its own CO2 emissions, which currently account for 2% of global industrial fossil CO2 emissions, and it has an opportunity to produce renewable energy, fuels, and materials for other sectors. The purpose of this study is to improve understanding of the decarbonization prospects of the PPI. The study provides insights on the magnitude of needed annual renewal rates for several possible net-zero target years of industrial fossil CO2 emissions in the PPI and discusses decarbonization opportunities, namely, energy and material efficiency improvement, fuel switching, electrification, renewable energy production, carbon capture, and new products. The effects of climate policies on the decarbonization opportunities are critically evaluated to provide an overview of the current and future business environment of the European PPI. The focus is on Europe, but other regions are analyzed briefly to widen the view. The analysis shows that there are no major technical barriers to the fossil-free operation of the PPI, but the sector renovates slowly, and many new opportunities are not implemented on a large scale due to immature technology, poor economic feasibility, or unclear political environment. [ABSTRACT FROM AUTHOR]

The treatment and disposal of sewage sludge is one of the most important and critical issues of wastewater treatment plants. One option for sludge liquidation is the production of fuel in the form of pellets from mixed sewage and paper mill sludge. This study presents the results of the combustion of pelletized fuels, namely sewage and paper mill sludge, and their 2:1 and 4:1 blends in a fluidized bed combustor. The flue gas was analysed after reaching a steady state at bed temperatures of 700–800 °C. Commonly used flue gas cleaning is still necessary, especially for SO2; therefore, it is worth mentioning that the addition of paper mill sludge reduced the mercury concentration in the flue gas to limits acceptable in most EU countries. The analysis of ash after combustion showed that magnesium, potassium, calcium, chromium, copper, zinc, arsenic, and lead remained mostly in the ash after combustion, while all cadmium from all fuels used was transferred into the flue gas together with a substantial part of chlorine and mercury. The pellets containing both sewage and paper mill sludge can be used as an environmentally friendly alternative fuel for fluidised bed combustion. The levelized cost of this alternative fuel is at the same current price level as lignite. [ABSTRACT FROM AUTHOR]

The hot pressing parameters and fiber ratio have an important influence on the dielectric properties of aramid insulating paper. In order to deeply explore its influence and the mechanism behind it, aramid insulating papers were made with different hot pressing temperatures and pressures as well as fiber ratios. Its tightness, dielectric constant, and AC breakdown strength were tested, and its microstructure was analyzed by scanning electron microscopy. It was found that with an increase in hot pressing temperature, pressure, and fibrid content, the overall dielectric constant of the insulating paper showed a slight upward trend, while the tightness and AC breakdown strength continued to increase. Hot pressing temperature and pressure have a synergistic effect on the dielectric properties of insulating paper. The effects of these two parameters on the dielectric properties of insulating paper are similar, while the AC breakdown strength is greatly affected by the fiber ratio. In this paper, the influence mechanism by which the microstructure and fiber crystallinity of insulating paper is affected in the hot pressing process is discussed. [ABSTRACT FROM AUTHOR]

The pulp and paper industry is recognized as a well-established sector, which throughout its process, generates a vast amount of waste streams with the capacity to be valorized. Typically, these residues are burned for energy purposes, but their use as substrates for biological processes could be a more efficient and sustainable alternative. With this aim, it is essential to identify and characterize each type of waste to determine its biotechnological potential. In this context, this research highlights possible alternatives with lower environmental impact and higher revenues. The bio-based pathway should be a promising alternative for the valorization of pulp and paper industry wastes, in particular for bioproduct production such as bioethanol, polyhydroxyalkanoates (PHA), and biogas. This article focuses on state of the art regarding the identification and characterization of these wastes, their main applied deconstruction technologies and the valorization pathways reported for the production of the abovementioned bioproducts. [ABSTRACT FROM AUTHOR]

Forecasting has extreme importance in industry due to the numerous competitive advantages that it provides, allowing to foresee what might happen and adjust management decisions accordingly. Industries increasingly use sensors, which allow for large-scale data collection. Big datasets enable training, testing and application of complex predictive algorithms based on machine learning models. The present paper focuses on predicting values from sensors installed on a pulp paper press, using data collected over three years. The variables analyzed are electric current, pressure, temperature, torque, oil level and velocity. The results of XGBoost and artificial neural networks, with different feature vectors, are compared. They show that it is possible to predict sensor data in the long term and thus predict the asset's behaviour several days in advance. [ABSTRACT FROM AUTHOR]

A transpiration-type thermoelectric-power-generating paper based on previously developed carbon nanotube (CNT) composite paper, which is a composite material of CNTs and pulp that can generate thermoelectric power, was developed. The newly developed thermoelectric-power-generating material does not require an external high-temperature heat source due to the ability of paper to absorb liquid through capillary action and heat of vaporization generated when the liquid evaporates. The aim of this study is to investigate the feasibility of realizing the transpiration-type thermoelectric-power-generating paper. To begin with, the type of paper used as raw material for the composite paper was examined, and the fabrication process was modified in order to obtain more efficient liquid absorption based on capillary action. Then, the absorbing ability of the liquid was evaluated. Next, the feasibility of thermoelectric power generation using the heat of vaporization was confirmed. Moreover, for more efficient thermoelectric conversion, multisheet structures were also studied. Through several experiments, the material's feasibility was verified, and it was confirmed that more power can be easily obtained through the use of multiple sheets. Specifically, a single sample spontaneously generated a temperature difference of up to 1.7 °C due to the heat of vaporization, generating an electromotive force of 36 μ V. From the sample with a five-sheet structure, an electromotive force of 356 μ V was obtained at a temperature difference of 2 °C. This material can be used in watery environments, such as rivers, lakes, and hot springs, and is expected to become a new energy-harvesting device. [ABSTRACT FROM AUTHOR]

Although there are opportunities to reduce electrical energy demand in unit processes of mechanical pulp-based paper and paperboard production, this may not be financially beneficial. This is generally because energy optimization opportunities connected to reduced refiner electricity demand in mechanical pulping systems also results in less steam available for the drying of the paper. As modern high consistency refiner systems produce approximately one ton of steam for each MWh of electricity when producing one ton of pulp, a reduction in electric energy demand leads to increased fuel demand in steam boilers to compensate for the steam shortage. In this study, we investigated what the financial and environmental situation would look like if we were to expand the system border from a paper mill to a larger system consisting of a mechanical pulp-based paper or paperboard mill, a district heating system with an incineration boiler and a chemical pulp mill. Mechanical pulp production has a wood to product yield of >90%, a high electric energy demand to separate woodchips to pulp and is a net producer of heat and steam while chemical pulp-based production has a wood to product yield of 50%, a low electric energy demand and is a net heat and electricity producer due to the combustion of dissolved wood polymers. The aim of this research is to create useful and robust models of how to use excess heat from certain industry sites to cover the steam shortage in other industry sites by means of utilizing and optimizing the district heating systems connecting these sites. For this purpose, we used a simulation tool which dynamically allows us to evaluate different scenarios. Our results shows that there is great potential to reduce both carbon dioxide emissions and production costs for industry sites and society by means of these tools. [ABSTRACT FROM AUTHOR]

Natural and synthetic esters are increasingly being chosen instead of mineral oil for environmental and fire safety reasons. However, their use in power transformers is limited due to insufficiently well-understood ageing processes affecting their properties and the properties of cellulosic materials impregnated with them. The research results presented in many scientific papers prove that the use of esters slows the ageing process of cellulosic materials. This article presents the results of research aimed at answering the question of whether the effect of slowing the ageing process will also occur in the case of insulation with very low initial moisture. The answer to this question will allow us to better understand the role of water in the ageing process of the transformer's insulation system. The thermal ageing process was carried out at a temperature of 150 °C in closed systems. The degree of cellulose polymerisation was taken as a measure of the degree of paper ageing. Great attention was paid to measuring the water content in both paper and electro-insulating liquids at various stages of their ageing. Furthermore, measurements of the properties of electro-insulating liquids were made, which are considered markers of ageing. The test results obtained indicate that in the case of a dry insulation system, corresponding to the initial moisture of the new units, the type of liquid used to impregnate the cellulosic material does not significantly affect its depolymerisation process. However, in the case of paper impregnated with natural esters, a lower dynamic of moisture increase in insulation was observed. [ABSTRACT FROM AUTHOR]

The article presents studies on the impact of the significant process parameters of a paper machine with a Yankee cylinder on its production capacity and heat energy consumption for drying the paper web. Parameters such as machine speed, web moisture content before and after pressing, parameters of steam supplied to the cylinder and parameters of hot air flowing from the nozzles of the hood were analyzed. The study's results were used to optimize production to improve the energy efficiency and performance of the machine. In order to use the possible methods of improving the production capacity and heat energy consumption, the parameters of the production process were measured and the basic indicators characterizing the operation of the machine were calculated in the Yankee cylinder–dryer hood system. The correct functioning of the machine components and the possibility of their modernization were also analyzed. Technological and construction changes introduced based on the research results made it possible to increase the production capacity by 10% and to reduce the consumption of heat energy per 1 ton of produced paper by 16.3%. The article presents a description of changes in the technology of paper production and modernization of the tissue machine made in the years 2013–2022. [ABSTRACT FROM AUTHOR]

In the field of intelligent transportation, the planning of traffic flows that meet energy-efficient driving requirements necessitates the acquisition of energy consumption data for each vehicle within the traffic flow. The current methods for calculating vehicle energy consumption generally rely on longitudinal dynamics models, which require comprehensive knowledge of all vehicle power system parameters. While this approach is feasible for individual vehicle models, it becomes impractical for a large number of vehicle types. This paper proposes a digital model for vehicle driving energy consumption using vehicle speed, acceleration, and battery state of charge (SOC) as inputs and energy consumption as output. The model is trained using an optimized CNN-BiLSTM-Attention (OCBA) network architecture. In comparison to other methods, the OCBA-trained model for predicting PHEV driving energy consumption is more accurate in simulating the time-dependency between SOC and instantaneous fuel and power consumption, as well as the power distribution relationship within PHEVs. This provides an excellent framework for the digital modeling of complex power systems with multiple power sources. The model requires only 54 vehicle tests for training, which is significantly fewer than over 2000 tests typically needed to obtain parameters for power system components. The model's prediction error for fuel consumption under unknown conditions is reduced to 5%, outperforming the standard error benchmark of 10%. Furthermore, the model demonstrates high generalization capability with an R2 value of 0.97 for unknown conditions. [ABSTRACT FROM AUTHOR]

Insulation cellulose paper is a basic measure for a power transformer's remaining useful life, and its advantageous low cost, electrical, and mechanical properties have made it an extensive insulation system when impregnated in a dielectric liquid. Cellulose paper deteriorates as a result of ageing due to some chemical reactions like pyrolysis (heat), hydrolysis (moisture), and oxidation (oxygen) that affects its degree of polymerization. The condition analysis of cellulose paper has been a major concern since the collection of paper samples from an operational power transformer is almost impossible. However, some chemicals generated during cellulose paper deterioration, which were dissolved in dielectric liquid, have been used alternatively for this purpose as they show a direct correlation with the paper's degree of polymerization. Furthermore, online and non-destructive measurement of the degree of polymerization by optical sensors has been proposed recently but is yet to be available in the market and is yet generally acceptable. In mitigating the magnitude of paper deterioration, some ageing assessments have been proposed. Furthermore, researchers have successfully enhanced the insulating performance of oil-impregnated insulation paper by the addition of various types of nanoparticles. This study reviews the ageing assessment of oil-paper composite insulation and the effect of nanoparticles on tensile strength and electrical properties of oil-impregnated paper insulation. It includes not only significant tutorial elements but also some analyses, which open the door for further research on the topic. [ABSTRACT FROM AUTHOR]

Numerical simulation of polypropylene laminated paper insulation is a serious challenge, as it must take into account the layered structure and presence of longitudinal and radial gaps in the coils of the winded tape for cables with sector-shape conductive cores. Thus far, it has been performed only with serious simplifications. We propose a technique for numerical modeling of electric parameters in this type of insulation by reducing a complex 3D problem to a simplified 2D model that takes into account the main influencing factors. The results of modeling the distribution of electric field strength and current density in insulation are presented, and the influence of the location of gaps between the edges of winded tape on the conductivity of cable insulation is estimated. Analytical expressions are obtained for estimating the electrical resistance of insulation while taking into account the parameters of the butt gap between the insulating tapes. The results of calculations, numerical modeling, and experimentally measured values of electrical resistance are compared, showing that there is a good match. The main effects affecting the properties of polypropylene laminated paper insulation are described. [ABSTRACT FROM AUTHOR]

The momentum of the Fourth Industrial Revolution is driving increased demand for certain specific metals. These include copper, silver, gold, and platinum group metals (PGMs), which have important applications in renewable energies, green hydrogen, and electronic products. However, the continuous extraction of these metals is leading to a rapid decline in their ore grades and, consequently, increasing the environmental impact of extraction. Hence, obtaining metals from secondary sources, such as waste electrical and electronic equipment (WEEE), has become imperative for both environmental sustainability and ensuring their availability. To evaluate the sustainability of the process, this paper proposes using an exergy approach, which enables appropriate allocation among co-products, as well as the assessment of exergy losses and the use of non-renewable resources. As a case study, this paper analyzes the recycling process of waste printed circuit boards (PCBs) by disaggregating the exergy cost into renewable and non-renewable sources, employing different exergy-based cost allocation methods for the mentioned metals. It further considers the complete life cycle of metals using the Circular Thermoeconomics methodology. The results show that, when considering the entire life cycle, between 47% and 53% of the non-renewable exergy is destroyed during recycling. Therefore, delaying recycling as much as possible would be the most desirable option for minimizing the use of non-renewable resources. [ABSTRACT FROM AUTHOR]

Mass-impregnated (MI) cables have been used for many years as cables in high-voltage direct current (HVDC) systems. In line commutated converter (LCC) HVDC systems, polarity reversal for power flow control can induce significant electrical stress on MI cables. Furthermore, the mass oil and kraft paper comprising the impregnated insulation have significantly different coefficients of thermal expansion. Load fluctuations in the cable lead to expansion and contraction of the mass, creating pressure within the insulation and causing redistribution of the impregnant. During this process, shrinkage cavities can form within the butt gaps. Since the dielectric strength of the cavities is lower than that of the surrounding impregnation, cavitation phenomena in impregnated paper insulation are considered a factor in degrading insulation performance. Consequently, this study analyzes the electrical conductivity of thermally aged materials and investigates the transient electric field characteristics within the cable. Additionally, it closely analyzes the formation and dissolution of cavities in MI cables during polarity reversal based on a numerical model of pressure behavior in porous media. The conductivity of the impregnated paper indicates that it has excellent resistance to thermal degradation. Simulation results for various load conditions highlight that the interval of load-off time and the magnitude of internal pressure significantly influence the cavitation phenomenon. Lastly, the study proposes stable system operation methods to prevent cavitation in MI cables. [ABSTRACT FROM AUTHOR]

This paper focuses on proton exchange membrane fuel cell (PEMFC) operation at current densities in the order of 6 A/cm2. Such high current densities are conceivable when the traditional carbon fiber papers are replaced with perforated metal plates as the gas diffusion layer to enhance waste heat removal, and at the same time the relative humidity inside the fuel cell is kept below 100% by applying appropriate operating conditions as was found in previous one-dimensional modeling work. In the current paper, we applied a three-dimensional, multi-phase computational fluid dynamics model based on Ansys-CFX to obtain additional insight into the underlying physics. The calculated pressure drops are in very good agreement with previous one-dimensional modeling work, and the current densities in all case studies are in the order of 5–6 A/cm2, but different from the previous one-dimensional study, the results suggest that the relative humidity is very close to 100% throughout the entire channel length when the inlet relative humidity is 100%, ensuring best hydration cell conditions and hence best performance. Importantly, the model results suggest that fuel cell performance at a high current density in conjunction with relatively low stoichiometric flow ratios around 1.5–2 is possible. [ABSTRACT FROM AUTHOR]

The defossilisation of the agricultural sector is driven by intense worldwide academic research on non-fossil, renewable and energy-efficient agriculture, and the acknowledgment of the need for sustainable farming practices. For this purpose, not only technical transformations but also socio-technical system changes towards sustainability need to take place in a co-evolutionary manner. This paper investigates structural and qualitative characteristics of the knowledge produced by research on fossil-energy-free agriculture. We provide evidence on the worldwide research directions, as well as investigate whether academic research and publicly funded research projects foster knowledge creation for the desired transformation. Bibliographic maps are constructed using a query-based methodology as social networks to investigate the efficiency of the EU-funded research to achieve the goals set for the 2050 EU Green Deal. The H2020-funded papers are further analysed with dictionary-based text analysis to quantify the relative emphasis of different types of knowledge in the text. This approach is eventually used to relate transformational capacity to project profiles in the European Union, to evaluate past funding schemes and to improve the shape of future research programs on renewable and sustainable agriculture. [ABSTRACT FROM AUTHOR]

The increasing global water pollution leads to the need for urgent development of rapid and accurate water quality monitoring methods. Microbial fuel cells (MFCs) have emerged as real-time biosensors for biochemical oxygen demand (BOD), but they grapple with several challenges, including issues related to reproducibility, operational stability, and cost-effectiveness. These challenges are substantially shaped by the selection of an appropriate air-breathing cathode. Previous studies indicated a critical influence of the cathode on both the enduring electrochemical performance of MFCs and the taxonomic diversity at the electroactive anode. However, the effect of different gas diffusion electrodes (GDE) on 3D-printed single-chamber MFCs for BOD biosensing application and its effect on the bioelectroactive anode was not investigated before. Our study focuses on comparing GDE cathode materials to enhance MFC performance for precise and rapid BOD analysis in wastewater. We examined for over 120 days two Pt-coated air-breathing cathodes with distinct carbonaceous gas diffusion layers (GDLs) and catalyst layers (CLs): cost-effective carbon paper (CP) with hand-coated CL and more expensive woven carbon cloth (CC) with CL pre-applied by the supplier. The results show significant differences in electrochemical characteristics and anodic biofilm composition between MFCs with CP and CC GDE cathodes. CP-MFCs exhibited lower sensitivity (16.6 C L mg−1 m−2) and a narrower dynamic range (25 to 600 mg L−1), attributed to biofouling-related degradation of the GDE. In contrast, CC-MFCs demonstrated superior performance with higher sensitivity (37.6 C L mg−1 m−2) and a broader dynamic range (25 to 800 mg L−1). In conclusion, our study underscores the pivotal role of cathode selection in 3D-printed MFC biosensors, influencing anodic biofilm enrichment time and overall BOD assessment performance. We recommend the use of cost-effective CP GDL with hand-coated CL for short-term MFC biosensor applications, while advocating for CC GDL supplied with CL as the preferred choice for long-term sensing implementations with enduring reliability. [ABSTRACT FROM AUTHOR]

Carbon emissions from the Yangtze River Economic Belt are an important element of China's carbon emission endeavor, and a study of its emission reduction pathway can provide a reference for the country's overall management of carbon emission reduction. From the perspective of energy consumption, this paper uses the carbon emission factor method to estimate the carbon emissions of the transportation industry in the Yangtze River Economic Belt during 2006–2020, based on the extended STIRPAT model, considering the influence of seven factors, i.e., population size, urbanization rate, GDP per capita, transportation added value, energy structure, energy intensity, and transportation intensity, on carbon emissions. Based on these factors, a scenario analysis, combined with a forecasting model, is used to predict the peak carbon performance of the transportation industry under different development scenarios. The results show that the overall carbon emissions of transportation in the YEB from 2006 to 2020 show a fluctuating upward trend, and the downstream carbon emissions are significantly higher than those in other regions. The main factors influencing carbon emissions from transportation in different upstream, midstream, and downstream regions vary, with both population and economic factors contributing to carbon emissions, while technical factors affect them differently. There are significant differences in the peak carbon performance of transportation under different development scenarios, and the government should take effective measures to work towards achieving the goals of the low-carbon or enhanced low-carbon scenarios. [ABSTRACT FROM AUTHOR]

Recently, as the use of wearable devices and the demand for eco-friendly energy have increased, many studies have been conducted on triboelectric nanogenerators (TENGs), which can economically harvest energy. Paper is considered a promising substrate and frame material that can be used to manufacture self-powered TENGs, owing to its flexibility, low cost, and accessibility. Herein, we present a sandwich-structured foldable paper-based TENG (FP-TENG) that comprises flexible materials and uses paper as a substrate. The FP-TENG can generate up to 572 mW/m2 of power via contact–separation of the triboelectric electrified body at the top and bottom. With more folds of the FP-TENG, the triboelectric cross-sectional area increases, and, thus, the electrical output increases. In addition, the proposed TENG exhibits excellent durability without signal degradation under 5000 cycles of repeated pushing motions. To demonstrate its practicality, the FP-TENG was manufactured in the form of a wristwatch Velcro and connected to an electronic watch panel to supply power. Various deformations are possible with origami, and they can drive wristwatches through external forces. Therefore, the FP-TENG is expected to be utilized as a sustainable and promising eco-friendly energy source for small electronic devices. [ABSTRACT FROM AUTHOR]

Oil-pressboard/paper insulation materials are essential in transformers for ensuring their safe and stable operation, primarily due to their roles in spatial electric field distribution and charge migration mechanisms. Current spatial distribution analyses rely on computational methods that lack empirical validation, particularly for oil-pressboard/paper composites. This study leverages the principles of the Kerr electro-optic effect to develop a rapid measurement platform for electric fields within oil-pressboard/paper insulation under impulse voltage conditions, which measures the spatial electric field characteristics using Cu-Cu and Al-Al electrodes under various scenarios: with asymmetric and symmetric pressboard coverage and different numbers of insulating paper layers. Findings indicated: (1) In asymmetric pressboard models, Cu-Cu electrodes exhibit a consistent peak electric field of approximately 16 kV/mm, while Al-Al electrodes show peak values of 18.13 kV/mm and −14.98 kV/mm. Charge density patterns are similar, with Cu-Cu at about 68 μC/m2 and Al-Al at 11.2 μC/m2 and −124.8 μC/m2. (2) Symmetric models present consistent peak electric fields and charge densities for both polarities. (3) Increasing insulating paper layers elevates electric field strengths. Both electrodes show the similar peak field of about 17 kV/mm with differing paper layers due to higher charge injection from the Al electrode. (4) Utilizing the Schottky effect and field emission principles, the study clarifies charge generation and migration mechanisms. These insights could provide a theoretical foundation for designing and verifying oil-pressboard/paper insulation structures in transformers. [ABSTRACT FROM AUTHOR]

The main insulation system in high-voltage direct current (HVDC) transformer consists of oil-paper insulation. The formation of space charge in insulation paper is crucial for the dielectric strength. Unfortunately, space charge behavior changes because of the corrosive sulfur substance in oil. This paper presents the space charge behavior in insulation paper induced by copper sulfide generated by corrosive sulfur in insulation oil. Thermal aging tests of paper-wrapped copper strip called the pigtail model were conducted at 130 °C in laboratory. Scanning electron microscopy (SEM) was used to observe the surface of copper and paper. Pulse electroacoustic (PEA) and thermally stimulated current (TSC) methods were used to obtain the space charge behavior in paper. Results showed that both maximum and total amount of space charge increased for the insulation paper contaminated by semi-conductor chemical substance copper sulfide. The space charge decay rate of contaminated paper was significantly enhanced after the polarization voltage was removed. The TSC results revealed that copper sulfide increased the trap density and lowered the shallow trap energy levels. These results contributed to charge transportation by de-trapping and trapping processes. This improved charge transportation could be the main reason for the decreased breakdown voltage of paper insulation material. [ABSTRACT FROM AUTHOR]

The building sector contributes to 40% of the total final energy consumption and 36% of CO2 emissions in Europe, and these are set to increase in the coming years. International directives are pushing towards a decarbonisation roadmap to improve the quality of cities and the health of citizens. Buildings have a potentially central role in terms of energy transition as a means to produce and save energy. Photovoltaic shading devices (PVSDs) protect buildings from direct solar radiation and overheating while producing renewable electricity onsite and increasing the users' thermal comfort. Even though the potential of the PVSD is considerable, the sector is still unexplored, and few studies on the topic are available in the literature. This systematic review aims to present an exhaustive overview of the current literature on state-of-the-art PVSDs by analysing the scientific framework in terms of the status of the research. It presents a performance-based approach focusing on innovative products, PVSD design strategies, and energetic performance in distinct climate conditions and configurations. In particular, 75 articles and about 250 keywords were identified, selected, and analysed. The literature review serves as a basis for further R&D activities led by both the industrial and the academic sectors. [ABSTRACT FROM AUTHOR]

Mineral oil is widely used as liquid insulation in high voltage equipment. Due to environmental considerations, recently natural esters have been considered as naturally friendly liquid insulation candidates for high voltage transformers. In this experiment, transformer insulation paper was subjected to get accelerated aging test with copper strip in natural ester in a hermeneutical heat-resistant glass bottle at temperatures of 120 °C and 150 °C for 336 h, 672 h and 1008 h. The experimental results of Fourier transform infrared spectroscopy (FTIR) showed that the intensity of the absorbance peak of the O-H functional group decreased with aging, while the intensity of the C-H and C=O functional group absorbance peaks have increased with aging and the intensity of the C-O functional group absorbance peak has a tendency to increase with aging. The energy dispersive X-ray spectroscopy (EDS) experimental results showed that the weight percent of the element C increased with aging and the weight percent of the element O has decreased with aging. The experimental results show a good correlation between the degree of polymerization (DP) and the weight percent of O element. This indicates that EDS may be used as a new method for estimating the DP of transformer insulation paper. [ABSTRACT FROM AUTHOR]

Microgrids (MGs) are the new paradigm of decentralized networks of renewable energy sources, loads, and storage devices that can operate independently or in coordination with the primary grid, incorporating significant flexibility and supply reliability. To increase reliability, traditional individual MGs can be replaced by networked microgrids (NMGs), which are more dependable. However, when it comes to operation and control, they also pose challenges for cyber security and communication reliability. Denial of service (DoS) is a common danger to DC microgrids with advanced controllers that rely on active information exchanges and has been recorded as the most frequent cause of cyber incidents. It can disrupt data transmission, leading to ineffective control and system instability. This paper proposes digital twin (DT) technology as an integrated solution, with new, advanced analytics technology using machine learning and artificial intelligence to provide simulation capabilities to predict and estimate future states. By twinning the cyber-physical dynamics of NMGs using data-driven models, DoS attacks targeting cyber-layer agents will be detected and mitigated. A long short-term memory (LSTM) model data-driven digital twin approach for DoS attack detection and mitigation is implemented, tested, and evaluated. [ABSTRACT FROM AUTHOR]

This article is a summary of many years of work by the author, in which the thermal properties of various types of insulating liquids, used in power transformers, were evaluated. Recently, esters have been displacing mineral oil. There is a common view that mineral oil has better thermal properties than esters. This claim is supported by comparative results of tests of both materials as a liquid only filling the remaining volume of the transformer. The effect of the type of liquid on the thermal properties of the paper–oil insulation has not been analyzed so far. On this basis, the conclusions formulated may be incomplete. For this reason, the author has analyzed the influence of the type of liquid on both the thermal properties of the liquid filling the remaining volume of the transformer and the paper–oil insulation. It was proved that the more effective liquid filling the remaining volume of the transformer was indeed mineral oil. On the other hand, a more effective electrical insulating liquid, which is an element of paper–oil insulation, is a natural ester. A comprehensive assessment that takes into account both the paper–oil insulation and the remaining transformer volume showed that the natural ester proved to be a slightly more effective electrical insulating liquid than the other analyzed liquids. [ABSTRACT FROM AUTHOR]

Breakdown strength is an important electrical property of insulating paper. Oil-impregnated paper of various aging states was prepared. Its breakdown voltage was then measured at pulsating direct current (DC) voltage with various ripple factors, and alternating current (AC) and DC voltage for comparison, respectively. The AC breakdown voltage is the smallest, and pulsating DC (r = 1/5) breakdown voltage is the greatest before the paper reaches its end of life. A dielectric model was adopted to investigate the difference in magnitude of breakdown voltage at different voltage waveforms. Meanwhile, it was found that breakdown voltage fluctuated and even increased occasionally during the thermal aging process, and a somewhat opposite changing tendency versus aging time was observed for breakdown voltage at DC voltage and pulsating DC voltage with small ripple factors (r = 1/5 and 1/3), compared with AC voltage. The degree of polymerization (DP) and moisture content of the paper were measured, and the characteristics of the pores and cracks of the paper were obtained to investigate the possible influencing factors of breakdown voltage at different aging states. The results showed that the moisture content, oil absorption ability associated with pores and cracks of paper, and the damage to paper structure all contributed to the variation of the breakdown voltage versus aging time, while the importance of their influence differed as the aging state of paper varied. [ABSTRACT FROM AUTHOR]

One of the possible causes of transformer failures is high moisture in the winding insulation system. In an extreme case, when the critical temperature is exceeded, a sudden release of water vapor from the transformer insulation, called the bubble effect, can occur. This article analyzes the initiation temperature of the bubble phenomenon in various solid insulation materials (Kraft cellulose paper and aramid-based high-temperature papers such as Nomex® 910 and Nomex® 926) immersed in two electro-insulating liquids (mineral oil and Midel 7131 synthetic ester). The initiation temperature of the bubble effect depends mainly on the moisture content of the solid insulation, but it was found to be slightly lower for high-temperature materials than for cellulose. However, after taking into account the differences related to uneven water absorption of the tested materials, the differences in the initiation temperature of individual solid materials are very small. Synthetic ester, compared to mineral oil, slightly increases the bubble initiation temperature, regardless of the solid material used. [ABSTRACT FROM AUTHOR]

Generally, impregnation of solid insulation is performed to increase the dielectric strength and reduce the dielectric losses of solid insulants. This increase in dielectric strength depends on the oil's diffusion and dielectric properties. This paper investigates the diffusion behavior of mineral oil and ester fluids (synthetic, natural, and mixed) to understand the influence of oil diffusion on paper breakdown voltage. To better understand this phenomenal influence, cellulose insulation paper of different thicknesses has been considered. Wetting characteristics of various oil-paper insulation systems were investigated with and without thermal stressing. Thermal aging was carried out as per modified ASTM D1934 at 110 °C, 140 °C, 160 °C, and 185 °C respectively for 2 weeks. The wetting characteristics and influence of different oils on paper breakdown voltage were explicitly reported. It is inferred that paper wetting characteristics are attributable to the type of oil, the thickness of paper, and the aging factor of oil-paper insulation. Importantly, the increase in paper dielectric strength and diffusion behavior for ester fluids is found to be superior to that of the mineral insulating oils. [ABSTRACT FROM AUTHOR]

Heat pumps have the potential for several applications across various industrial sectors, showcasing significant promise, especially in sectors such as pulp and paper, food and beverage, chemical, non-metallic minerals, and machinery. Envisioning the near future, there is confidence that heat pumps can achieve temperatures above 200 °C, offering substantial potential for utilization in these sectors. Nevertheless, a crucial aspect for the advancement of high-temperature heat pumps is the selection of the fluid. Fluid selection involves considerations of both thermodynamic efficiency and environmental impact, requiring fluids with zero ODP, negligible GWP, and no PFAS. Moreover, it is essential to consider the risks to human health associated with a specific fluid. Despite extensive research, particularly in the realm of vapour compression heat pumps, choosing the most suitable working fluid for these applications is a complex undertaking. Therefore, this paper conducts a theoretical analysis to evaluate potential fluids with suitable thermodynamic properties for high-temperature heat pumps (HTHPs). The comparative results gleaned from this study provide valuable insights for the comprehensive analysis of fluids, showing promise within temperature ranges dictated by specific applications. The metrics employed in the comparison emphasise the merits of fluids in terms of the overall performance, dimensions, and operating ranges of applicable compressor, heat exchange capacity, transport properties, and safety. One noteworthy finding from the analysis is that maintaining a constant HTHP lift (at 40 K) results in having the highest COP across all fluids when the condensing temperature ranges between 85% and 90% of their respective critical temperatures. According to the results of the analysis, natural fluids, including water and alcohols like ethanol or methanol, emerge as particularly compelling candidates. [ABSTRACT FROM AUTHOR]

This paper studied the impact of moisture on the correlated characteristics of the condenser bushings oil-paper insulation system. The oil-impregnated paper samples underwent accelerated thermal aging at 130 °C after preparation at different initial moisture contents (1%, 3%, 5% and 7%). All the samples were extracted periodically for the measurement of the moisture content, the degree of polymerization (DP) and frequency domain dielectric spectroscopy (FDS). Next, the measurement results of samples were compared to the related research results of transformer oil-paper insulation, offering a theoretical basis of the parameter analysis. The obtained results show that the moisture fluctuation amplitude can reflect the different initial moisture contents of insulating paper and the mass ratio of oil and paper has little impact on the moisture content fluctuation pattern in oil-paper but has a great impact on moisture fluctuation amplitude; reduction of DP presents an accelerating trend with the increase of initial moisture content, and the aging rate of test samples is higher under low moisture content but lower under high moisture content compared to the insulation paper in transformers. Two obvious "deceleration zones" appeared in the dielectric spectrum with the decrease of frequency, and not only does the integral value of dielectric dissipation factor (tan δ) reflect the aging degree, but it reflects the moisture content in solid insulation. These types of research in this paper can be applied to evaluate the condition of humidified insulation and the aging state of solid insulation for condenser bushings. [ABSTRACT FROM AUTHOR]

In this paper, the combustion behavior of low rank coal and its product after hydrothermal carbonization with paper sludge hydrochar were studied. The Raman technique was used to compare the structural differences between raw coal and the product. Thermogravimetric analysis was employed to conduct experiments of single sample and their mixtures with different proportions at a heating rate of 20 °C/min, the activation energy of chemical reactions was calculated. The results showed that upgraded product had higher carbon ordering degree than raw coal and the ignition temperature and burnout temperature of the product were advanced. Compared with raw coal, the combustion characteristic parameters C and S of the product were higher, indicating that its combustibility was better. As for the mixture, when the paper sludge hydrochar ratio was not more than 10%, the mixed fuel combustion curve was still similar to coal curve. After the paper sludge hydrochar ratio exceeded 10%, the activation energy of the mixed combustion reaction of paper sludge hydrochar and upgraded coal was lower than that of raw coal and paper sludge hydrochar. These results indicated that the mixture of upgraded coal and paper sludge hydrochar as mixed fuel was a better option. [ABSTRACT FROM AUTHOR]

The paper reports the results of a comparative assessment concerned with the effectiveness of identifying the basic forms of partial discharges (PD) measured by the acoustic emission technique (AE), carried out by application of selected machine learning methods. As part of the re-search, the identification involved AE signals registered in laboratory conditions for eight basic classes of PDs that occur in paper-oil insulation systems of high-voltage power equipment. On the basis of acoustic signals emitted by PDs and by application of the frequency descriptor that took the form of a signal power density spectrum (PSD), the assessment involved the possibility of identifying individual types of PD by the analyzed classification algorithms. As part of the research, the results obtained with the use of five independent classification mechanisms were analyzed, namely: k-Nearest Neighbors method (kNN), Naive Bayes Classification, Support Vector Machine (SVM), Random Forests and Probabilistic Neural Network (PNN). The best results were achieved using the SVM classification tuned with polynomial core, which obtained 100% accuracy. Similar results were achieved with the kNN classifier. Random Forests and Naïve Bayes obtained high accuracy over 97%. Throughout the study, identification algorithms with the highest effectiveness in identifying specific forms of PD were established. [ABSTRACT FROM AUTHOR]

The aim of the work was to prepare and test a paper-oil insulation system according to the recommendations of CIGRE (Conseil International des Grands Réseaux Électriques) with the parameters X = 50% and Y = 30%. Pressboard was moistened to a water content of (5.0 ± 0.2) wt.% The loss tangent was measured using a DIRANA meter (FDS-PDC dielectric response analyzer) in the frequency range 10−4 Hz–5000 Hz for 6 temperatures from 293.15 K to 333.15 K with a step of 8 K. The waveforms simulated by the DIRANA software were fitted to the experimental dependence of the loss tangent. The fitting process was performed using two methods. In the first method, the measuring temperature value as well as X and Y values were entered into the software. The estimated moisture content of the insulation varied from about 1.4 to about 5.2 wt.%. The average value of moisture content was (3.73 ± 1.11) wt.%. In the second method, only the measuring temperature value was entered into the software. This improved the quality of matching. The estimated average moisture content was (5.83 ± 0.25) wt.%. It was found that the dimensions of the oil channel clearly affected the quality of the fitting process. By not taking into consideration real values of oil channel, the quality of the moisture content estimation was significantly improved. [ABSTRACT FROM AUTHOR]

The resistivity of oil impregnated paper will decrease during its aging process. This paper takes paper resistivity as an assessment index to evaluate the insulation condition of oil impregnated paper in power transformer. The feasibility of this method are discussed in two aspects: reliability and sensitivity. Iterative inversion of paper resistivity was combined with finite element simulation. Both the bisection method and Newton's method were used as iterative methods. After the analysis and comparison, Newton's method was selected as the first option of paper resistivity iteration for its faster convergence. In order to consider the spatial distribution characteristic of paper aging and enhance the calculation accuracy, the resistivity calculation is expanded to a multivariate iteration based on Newton's method, in order to consider the spatial distribution characteristic of paper aging and improve the calculation accuracy. This paper presents an exploratory research on condition assessment of oil impregnated paper insulation, and provides some reference to the security and economy operation of power transformers. [ABSTRACT FROM AUTHOR]

A helium (He) dielectric barrier discharge plasma jet (DBD jet) was used for the first time for treating graphite foil as the current collector of a paper-based fluidic aluminum-air battery. The main purpose was to improve the distribution of the catalyst layer through modification and functionalization of the graphite foil surface. The plasma functionalized the graphite foil surface to enhance the wettability where the more hydroxyl could be observed from XPS results. The 30 s-He DBD jet treatment on the graphite foil significantly improved the battery performance. The best current density of 85.6 mA/cm2 and power density of 40.98 mW/cm2 were achieved. The energy density was also improved to 720 Wh/kg. [ABSTRACT FROM AUTHOR]

Hydrogen production through electrolysis using renewable resources is highly promising for reducing greenhouse gas emissions. While significant efforts have focused on developing more efficient and cost-effective catalysts to lower hydrogen production costs, catalysts are not the primary expense in electrolyzer fabrication. In the case of Proton Exchange Membrane Water Electrolyzers (PEMWEs), other components—such as the proton membrane, gas diffusion layer (GDL), and bipolar plates—contribute more to overall costs. To explore this, a study was conducted on the performance of PEMWEs with various carbon paper GDLs, developed in the lab, on the cathodic side. This study examined how properties like electrical conductivity, porosity, and gas permeability affect performance. These findings emphasize the need to optimize components beyond catalysts to improve the cost-effectiveness of hydrogen production through electrolysis. [ABSTRACT FROM AUTHOR]

As a core component of clean energy technology, proton exchange membrane fuel cells (PEMFC) play a crucial role in promoting the evolution of energy structures and realizing sustainable development, representing an environmentally friendly energy conversion strategy. This paper identifies the key core technology themes in the field of the proton exchange membrane fuel cells by constructing patent and paper datasets in the field, applying the BERTopic model for theme identification, and calculating the key core technology scores of each theme using the importance, innovativeness, and high competitiveness barriers to identify the key core technology themes in the field, so as to provide guidance and references for the relevant research and practice. The results of the study show that patent documents and academic papers show obvious differentiation in technical themes: the key core technologies identified in patent texts include 'battery separator materials', 'rubber sealing materials', and 'porous carbon fibre materials'. The key core technologies identified in the academic paper of the thesis include 'palladium-based electrocatalys', 'graphene oxide composite film', and 'platinum-graphene oxide catalyst'. [ABSTRACT FROM AUTHOR]

Hydrothermal liquefaction (HTL) is an effective biomass thermochemical conversion technology that can convert organic waste into energy products. However, the HTL process is influenced by various complex factors such as operating conditions, feedstock properties, and reaction pathways. Machine learning (ML) methods can utilize existing HTL data to develop accurate models for predicting product yields and properties, which can be used to optimize HTL operation conditions. This paper presents a bibliometric review on ML applications in HTL from 2020 to 2024. CiteSpace, VOSviewer, and Bibexcel were used to analyze seven key bibliometric attributes: annual publication output, author co-authorship networks, country co-authorship networks, co-citation of references, co-citation of journals, collaborating institutions, and keyword co-occurrence networks, as well as time zone maps and timelines, to identify the development of ML in HTL research. Through the detailed analysis of co-occurring keywords, this study aims to identify frontiers, research gaps, and development trends in the field of ML-aided HTL. [ABSTRACT FROM AUTHOR]

The EU has set the ambitious target of raising the share of EU energy consumption produced from renewable resources to 32% by 2030, with a target of climate neutrality by 2050. The aim of this paper is to assess the role of biomass usage in the context of these targets. The paper identifies the progress made between 2013 and 2022 by focusing on a selection of EU countries. The largest bioenergy increments of 130, 77, and 60 PJ were reported for Poland, Sweden, and the Netherlands. This study evaluates the crucial role of co-generation and heat in EU regions, with biomass usage between 55 and 80% of the combined heat and power (CHP) energy in Nordic countries. The future perspectives for bioenergy based on EU policies, biomass resources, and technical issues were addressed. The EU possesses around 9% of the global biomass supply, ensuring a certain level of biomass resource dependence. Thus, the biomass usage demand in energy production, non-energy sectors, and transport is expected to rise, leading to increments of 13–76% on biomass imports. It appears that bioenergy development is mostly limited by economic issues and uneven support for bioenergy in different EU countries as well as environmental issues. The study shows a promising and sustainable potential of bioenergy in the EU as a renewable energy source while minimizing negative impacts on the environment and the economy. By 2050, liquid biofuels are likely to be increasingly used in the transport sector. Non-energy sector usage of biomass is still in an early stage of development, except for the pulp and paper industry, and significant use of biomass in non-energy sectors seems unlikely in the near future. [ABSTRACT FROM AUTHOR]

Finding sustainable solutions to the increasing waste generation in Ghana has received a lot of attention in recent years. Through several waste-to-energy processes, the energy potential of municipal solid waste has recently witnessed significant technological advancements. The Renewable Energy Master Plan has projected the production of about 122 MWp from waste-to-energy installations by 2030 in Ghana. To help policymakers and engineers achieve national goals, this paper reviews the waste generation in Ghana estimated from 2010 to 2030 and the status of various bioenergy technologies in Ghana. This paper further estimates the energy recovery potential of municipal solid waste in Ghana under incineration, anaerobic digestion, and landfill gas recovery technologies. The review establishes that, by 2030, municipal solid waste generation will increase by 123% of the 2023 quantities and may produce 1484.25 MW of installed electricity capacity and 13,002.03 GWh per year, which would amount to nearly 59% of Ghana's 2030 renewable energy target. Additionally, it was determined that anaerobic digestion, incineration, and landfill gas recovery technologies, when properly developed, will add 105.33 MW, 301.4 MW, and 377.31 MW of installed electrical capacity, respectively, to Ghana's energy mix in 2028. [ABSTRACT FROM AUTHOR]

In stationary power generation units such as distributed remote site power systems and ship power systems, diesel engine generator systems are essential for supplying electricity. This paper proposes a digital twin diesel generator system for teaching and research purposes. A five-layer resilient architecture, including a web interface layer, server cluster layer, real-time data layer, controller layer, and equipment layer, is proposed in this paper. Based on the resilient architecture, users are able to build, implement and monitor the digital twin through web interfaces. Apart from MATLAB/Simulink, a modeling tool called M2PLink is developed to allow users to create mathematical models using a block diagram editor similar to Simulink. Various basic blocks for control systems are provided for users to form sophisticated models. These models are converted into executable codes which are downloaded to the simulator in the controller layer, where the real-time simulations are implemented. A web-based real-time monitoring interface with many widgets such as charts, oscilloscopes, and three-dimensional (3D) animation is also provided for users to customize their monitoring interface. All the signals can be traced and all the parameters can be tuned in the monitoring interface. The users are able to interact with the digital twin just like they do with the real system. The proposed system can not only be used for research such as digital twin-assisted real-time online monitoring but also for educational purposes, which is not only cost-effective but can also ensure the safety of the user as well as the equipment. [ABSTRACT FROM AUTHOR]

In this framework, experimental tests on different battery technologies, BMS and cooling systems are extremely important to extend the battery life and BEV performance (Sehil et al. [[13]]). Electrical machines and magnetic components, high-voltage voltage power converters, and battery storage systems are some basic bricks to build an effective and efficient energy conversion environment. Electrical Machines and Power Converters The electrical power conversion from renewable energy sources plays a crucial role in the development of a sustainable society. Finally, the fil rouge of every contribution in this section is oriented to investigate the power converters, electrical machines, magnetic components, and battery storage systems in actual energy conversion applications for renewable energy sources integration by a modelling approach. [Extracted from the article]

This article presents a method for quantification of methanol and ethanol integrated in the same gas-chromatographic run with a quantification of gases dissolved in mineral oil, making it an integrated tool in transformer diagnostics. The results of aging experiments at 120 °C and 60 °C of Kraft paper, copper, barrier, and pressboard immersed in mineral oil, as well as the aging of thermal upgrade paper in mineral and natural ester oil at 140 °C are presented, in order to investigate correlations between different aging markers and to evaluate their partitioning between oil and cellulose at defined conditions. The results of partitioning experiments at 60 °C showed that re-absorption of methanol from oil to the cellulose materials is faster than the re-absorption of furans. This means that methanol is a paper-degradation marker that can be used in diagnostics over shorter equilibrium times and for the detection of developing faults at broader temperature ranges. Furthermore, a statistical overview of methanol concentration from a database and two transformer fault diagnostic cases are presented. Therefore, in addition to an analysis of gases dissolved in oil, the use of methanol and ethanol in transformer fault and failure investigations should be explored and verified through transformer fault investigations and postmortem analyses. [ABSTRACT FROM AUTHOR]