Search

• Demolished concrete waste can be potentially utilised as recycled aggregates (RA). • Multi-stage processing and mechano-chemical treatment enhances the quality of concrete RA. • RAC incorporating treated RA shows better mechanical and durability properties. • Additional C S H formation is observed for RAC incorporating 35% treated RA. On account of the shortage of naturally occurring coarse aggregate, recycled aggregate (RA) made from crushed concrete debris is now used in the construction industry. With this rise in the utilisation of recycled aggregate in the construction sector, there has been extensive research into ways to improve its quality. The significant fraction of mortar remains that are left on the RA surface is the primary factor that affects its quality. Concrete made from RA loses strength and mechanical performance due to the attached mortar's increased porosity and water absorption values and the frailer transition region between the new mortar and aggregates. In order to minimise the old cement fractions and increase the quality, this paper studies the effect of concrete incorporating multi-stage processed RA from demolished concrete waste, followed by treatment with mechanical abrasion and sodium silicate immersion. The recycled aggregates were produced through multi-stage jaw crushing, followed by utilising natural aggregate, recycled aggregate, and recycled aggregate obtained after mechanical abrasion, followed by sodium silicate treatment for concrete mix design at various substitution percentages as coarse aggregates. The experimental investigation further progresses with the evaluation of mechanical and durability properties of concrete mixes, which is additionally followed by microstructural studies such as scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDAX), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and Thermogravimetry-differential thermal analysis (TG-DTA). The outcomes demonstrate that two-stage treatment, such as mechanical abrasion followed by sodium silicate immersion, yields superior-quality RA. Recycled aggregate concrete (RAC) made with these treated aggregates illustrated an increase in workability and density with respect to an untreated RAC mix. Furthermore, comparable strengths in compression, flexure, and tension are found in treated RAC mixes, particularly at 35% replacement levels, with respect to concrete mixes comprised of natural aggregates. A similar trend is detected in the chloride penetration tests and water sorptivity tests. In addition, the microstructural investigation confirmed the formation of additional calcium silicate hydrate for treated RAC mixes, particularly for the 35% substituted RA mix. On the basis of the results, it is suggested that multi-stage jaw crushing followed by treatment through mechanical abrasion and sodium silicate can potentially enhance the mechanical, microstructural, and durability performance of RAC. [ABSTRACT FROM AUTHOR]

• Different percentages of red mud were added in UHPC. • 20% replacement of red mud was preferable with respect to pumpability and buildability. • Upcycling the red mud in UHPC is an energy-saving and low-cost strategy to address disposal of solid waste. This paper introduces a new application of industrial solid waste red mud to use as a cementitious material in the development of ultra-high performance concrete (UHPC) performances. In addition, utilization of red mud can reduce the environmental impact of red mud landfill. For gaining this aims, UHPC specimens were prepared with different contents of red mud and analyzed the effects of different RM contents on the fluidity, setting time, mechanical properties, durability, drying shrinkage and microstructure of the red mud-based UHPC. The results indicated that fluidity was reduced to 310 mm at 20% red mud level, but it still belongs to enormous fluidity, which is convenient for construction. In addition, it is worth noting that using red mud instead of cement can significantly shorten the setting time, providing a new method for applying the UHPC rapid-repairing process. Red mud-based UHPC mortar prepared with appropriate red mud instead of cement exhibits higher mechanical properties, better durability and reduced drying shrinkage of UHPC during curing. After curing for 28d, the highest compressive strength of UHPC samples containing 20% red mud was 129.5 MPa, the compressive strength of the UHPC samples' sulfate resistance was 136.6 MPa, and the drying shrinkage value was around 414 µm. Moreover, observed information from scanning electron microscopy (SEM) noted that red mud can fill the micro-cracks between particles of cementitious materials, make the structure more compact and form new hydrates. Finally, the two characteristics of low cost and energy consumption further promote the sustainable application of red mud-based UHPC. Therefore, replacing OPC with 20% RM is meaningful to produce a sustainable UHPC mixture and field applications. [ABSTRACT FROM AUTHOR]