Search

The inner part of gewang (Corypha utan Lam.) trunk has significantly lower physical-mechanical properties as well as biodeterioration resistance, compared to outer parts. This study investigated a method for improving the physical-mechanical properties and biodeterioration resistance of glued laminated lumber made from the inner part of gewang trunk (GLIT). The effects of pretreating the lamina with densification and exposing the GLIT to smoking process were investigated. The seven layers of GLIT samples were bonded with isocyanate adhesive at a glue spread of 280 g/m2, then smoked for 15 days. Solid lumber pieces made from the inner part as well as the outer part of GLIT were also prepared for comparative purposes. Physical and mechanical properties of the lumber samples were tested according to Japanese agricultural standards. Meanwhile, dry-wood termite and wood decaying fungi resistances of the lumber samples were determined according to Indonesian standard. Results showed that overall physical-mechanical properties as well as dry-wood termite and decay resistances of densified-smoked GLIT were enhanced significantly. Pretreating of lamina and post-production smoking can be considered as a potential method to improve physical-mechanical properties and biodeterioration resistance of the GLIT.

The pin-penetration device is a minimally destructive instrument that is widely used to estimate the physical properties of wood, e.g., density, with advantages such as reduced testing times, low costs, and fewer defects induced in the wood being tested. In this study, such a device was used on 25 Indonesian hardwood species with a strength class (SC) distribution from SC II to IV (according to the Indonesian classification of wood SCs). Tests were conducted on three different orthogonal planes, i.e., cross-sectional, radial, and tangential planes. The wood density ranged from 0.28 to 0.88 g/cm3, and the specific gravity was 0.25 to 0.76. The cross-sectional plane penetration depth of the wood was significantly greater than that of either the radial or tangential plane, whereas the pin penetration values of the radial and tangential planes were not significantly different. A prediction model for predicting the density and specific gravity of wood via pin penetration showed a significant regression. Thus, the use of a pin-penetration device was found to be suitable for estimating wood density and specific gravity in a range of SCs of tropical wood species regardless of species.

The pattern of termite infestation was investigated in structural lumber, light Red Meranti (Shorea spp.), using a minimally destructive technique. The relationship between the visual inspection and the pin penetration approach in predicting the basic properties of wood was determined, and a pin penetration distribution value was mapped into a contour map based on the Kriging interpolation technique. Small wood block samples were exposed to reared subterranean termites Coptotermes curvignathus Holmgren (Isoptera: Rhinotermitidae). The characteristics of termite infestation and the changes in the physical-mechanical properties were investigated. The residual surface area of the samples was evaluated using Pilodyn®. The characteristics of the termite galleries found on small wood block samples were as follows: 1) the termite galleries varied in length, or 2) the galleries consisted of long flat tunnels in a longitudinal direction, clean, not decayed, and contained no soil residue. The weight loss percentage from this study exhibited a similar trend with the pin penetration depth, which was directly proportional to the exposure period. The pin penetration result from Pilodyn® generated distribution map that was represented the conditions and basic mechanical properties of the samples. Pilodyn® can be used a complement for visual inspection in in-situ assessment.

Acoustic panels are used to overcome noise problems; the purpose of this study was to determine the acoustical properties of particleboard made from Betung bamboo (Dendrocalamus asper). The acoustic parameters measured were the transmission loss (TL) value and sound absorption coefficient. Particleboards of two different densities (0.5 g/cm3 and 0.8 g/cm3) that were made with three particle sizes (fine, medium, and wool or excelsior) were used in this study. The sound TL value was measured in a reverberation room, while the sound absorption coefficient was determined using the impedance tube method. A single-number rating of sound transmission class (STC) was determined based on TL measurements. The results showed that sound TL and STC values of medium-density particleboard (0.8 g/cm3) were better than low-density (0.5 g/cm3) board. However, low-density particleboard performed well as sound absorber panels. Generally, the boards absorbed sound at low (< 500 Hz) and high frequency ranges (> 1000 Hz) and reflected sound at middle frequencies. The sound absorption coefficient was better with the fine- and medium-sized particles than with the wool size; meanwhile, boards made from wool- or excelsior-sized particles possessed higher TL and STC values.