Search

The paper analyses the structural peculiarity and design methods of the adjustable heat pump, bring forward a new project which used adjustable heat pump system for paper machine dryers. The system can enhance the steam’s function, accelerate the speed and economize the energy.

Through the comparative study of several enrichment machines ,the performance of the high-speed washer is introduced. The high-speed washer has high dewatering and washing efficiency, he pulp can be concentrated from 0.8% ~ 1.5% consistency to 10% ~ 15%;And it has high ash removal rate and good pulp washing effect also. It can effectively remove the ink particles, fillers, and other small impurities, improve the pulp brightness. At the same time ,the waste paper deinking process treatment systems has been developed.

This paper describes simulation of combustion characteristics under high ambient and high injection of biodiesel combustion by using CFD simulation. Diesel engine performance and emissions is strongly couple with fuel atomization and spray processes, which in turn are strongly influenced by injector flow dynamics. The principal objective of this research is to seek the effect of temperature and pressure on the spray characteristics, as well as fuel-air mixing characteristics. Experiments were performed in a constant volume chamber at specified ambient gas temperature and pressure. This research was continued with injecting diesel fuel into the chamber using a Bosch common rail system. Direct photography technique with a digital camera was used to clarify the real images of spray pattern, liquid length and vapor penetration. The method of the simulation of real phenomenon of diesel combustion with optical access rapid compression machine is also reviewed and experimental results are presented. The liquid phase of the spray reaches a maximum penetration distance soon after the start of injection, while the vapor phase of the spray continues to penetrate downstream. The condition to which the fuel is affected was estimated by combining information on the block temperature, ambient temperature and photographs of the spray. The increases in ambient pressure inside the chamber resulting in gain of spray area and wider spray angle. Thus predominantly promotes for a better fuel-air mixing. All of the experiments will be conducted and run by using CFD. The simulation will show in the form of images.

Magnetic stripe cards and magnetic recording paper are commonly used in credit cards, identity cards, and transportation tickets. Barium ferrite was used to prepare magnetic inks and the magnetic ink was coated onto the paper substrate to obtain the magnetic papers. The crystal structure of barium ferrite was characterized by X-ray diffraction (XRD) and the magnetic property of barium ferrite was tested by vibrating sample magnetometer (VSM) The performance of the magnetic recording paper and the surface morphology of the coating magnetic layer were also characterized. The results show that the magnetic ink based on barium ferrite with the formula of 41wt% of the barium ferrite powder, 14wt% of polyurethane, 36wt% of solvent and 9wt% of PVP has good printing characteristics and the magnetic recording papers have good performance.

This paper has a brief introduction to a algorithm that can automatically identify the defective cutting region when automatic paper cutter does quality analysis. The algorithm analyzed the characteristics of processed shear mark image,detected defects,found a critical point of defective part ,then a unique regional recognition algorithm was developed based on the basis of the general processing algorithm. The algorithms can pinpoint the region that cutting defects exist according to the coordinates of critical point accurately, improve the efficiency of quality analysis, and also has stated that image processing is available in the regional recognition of automatic paper cutter.

In digital printing process, the color reproduction quality is no longer determined by printing sequence, trapping, solid density and etc., since the technique is different from traditional printing technology. In order to analyze the effects of paper on color reproduction quality in digital ink-jet printing, three kinds of commercial paper were selected and a set of experiments were carried out by using color management technique to simulate the digital proofing. The density and chromaticity of both primary color and composite color in each printed were measured. The effects of paper’s characters on shadow, mid-tone and highlight were analyzed and discussed. Finally the influence on color reproduction quality principle, including chromaticity and absorbing characteristics of paper, was revealed. The conclusion has certain significance in directive function in ink-jet printing.

Return voltage diagnostic method is an effective method of non-destructive diagnosis in transformer insulating state. The current study is that through experiments get polarization spectrum to analysis the transformer insulating state, but not yet carried out the influence of various factors to the experimental results. So, based on the Debye model and specific parameters comes from one equivalent model of the actual transformer, this paper using RVM methods to simulation analysis maximum return voltage and dominant time constant under different factors. Simulation results show that the diagnostic methods that combine maximum return voltage value with dominant time constant can preferably reflect the transformer insulation state.

Pattern of number of PD events ("NE" for short) variation detected by UHF online monitoring was found through experiments, demonstrating that in the first half life of oil-paper insulation the NE value declined at the beginning and then kept stable, while it increased sharply in the later half. Least square linear regression was applied to calculate the changing rate ("CR" for short) of the latest 168 measurements of NE, which turned out to be an appropriate indicator of life stage for its monotonicity over time from the initiation of PD till final breakdown. The Grubbs method was also applied to exclude erroneous data and to determine the credible variation of CRs.

To assess the oil-paper insulation of transformer, it is necessary to establish the equivalent circuit for it regardless of using the time domain methods or frequency domain methods. Based on the principle of dielectric polarization, the extended Debye model is always adopted for the equivalent circuit of oil-paper insulation in transformer in most cases; however, it is usually difficult to determine the number of relaxation mechanisms in the model. This paper presents a method to determine it by the time domain dielectric spectra, namely, conduct differential operation for the depolarizing current of transformer’s oil-paper insulation to obtain the time domain dielectric spectra, and the number of spectrum peaks is equal to that of relaxation mechanisms. Thereby, the extended Debye model of the equivalent circuit of the oil-paper insulation of transformer can be built. This paper describes the analytical procedures of the time domain dielectric spectra method in detail and presents examples to validate its feasibility and rationality in determining the equivalent circuit model of transformer’s oil-paper insulation.

This study describes a new precise recycle module as a clean poduction pocess and an environmental protection consideration that uses micro electroetching (MECE) and a new design of an intercross tool to remove defective transparent conducting oxide (TCO) nanostructures from the optical PET diaphragm surfaces for e-paper surface. This process takes very little time to remove the TCO easily and cleanly and is highly efficient both technically and economically. A large diameter of the cathode of the intercross tool combined with a small gap between the cathode and the workpiece corresponds to a higher removal rate of TCO. This higher feed rate combined with enough voltage results in a shorter machining time. A high rotational speed of the intercross tool can also improve dregs discharge and allows a higher feed rate of the optical PET. A small end radius of the cathode or a thin cathode of the bulge-form tool takes less time for the same amount (20 nm) of TCO removal.