Search

The paper currency image recognition method based on Gabor filter set is discussed in this paper. According to the paper currency image features, the suitable parameters of Gabor filter set are selected for the extraction of paper currency characteristics, the multi-scale and multi-directional texture characteristics of paper currency image are gotten; then the texture images are meshed, and the row and column projection sum of grid pixels' average grey are calculated, finally, the template match method based on grid projection characteristics is used for paper currency recognition. Experiments show that, this method has strong anti-interference ability, it can raise the recognition rate of old or dirty paper currency greatly, and it costs little time.

Moisture has a detrimental effect on oil-paper insulation life by lowering electrical breakdown strength. How does the space charge behavior of the oil-paper insulation system consisted by oil gap and oil immersed insulation pressboard with different moisture content? The space charge characteristics of the mixed insulation consisted of oil gap and pressboard with three moisture content were investigated using the PEA measurement system. The space charge accumulation behaviors at the interface between oil gap and pressboard were analyzed. The distortion of the electrical field in the oil gap and pressboard was also analyzed. Results show that there are many charges injected into the oil and the pressboard. The charges accumulated at the interface between oil gap and pressboard. The charges accumulated in the mixed insulation system become less with the moisture content increased. The difference of the electric field strength in the oil gap and pressboard become smaller with the moisture content increased.

According to the features of paper currency CIS image, the fuzzy set theory is initial used to improve the contrast of banknote target and background, paper money’s edge pixels are obtained by scanning, and then the sub-pixel edges are fitted by least square method; in the fitting process, the error threshold method is applied for eliminating noisy edge points, then slope correction of paper money is carried out according to the angle of sub-pixel edge line and the note area is extracted, finally, fuzzy enhancement is used for the extracted image again. Experiments show that, this method has good versatility, high accuracy and strong anti-interference ability, it can even extract the paper currency area effectively in the edge deterioration and unfilled corner condition, and the enhanced image is in favor of subsequent paper currency recognition.

This paper focuses on scraps of paper splicing recovery issues. To deal with complex scraps restoration problem, first the image should be changed as pixel grey level binary image, generating binary matrix, and then classify the scraps using SOM neural network data and feature comparison method. Combining with the Euclidean distance discriminant method, we match the scraps of paper with same edges and obtain a complete stitching schematic finally.

The restoration of regular paper fragments can be solved by edge matching. Edge matching is based primarily on the length and location of the break in writing, however, it is possible that the edges of some regular paper fragments are blank. And so the error of restoration is the inevitable. In this case, it needs manual intervention based on the article content and then eliminate errors. Prior to the establishment of a mathematical model, there is a need for binarization of regular paper fragments with Matlab, then establish vector space model and construct edge contrast matrix, get the order after the Q cluster analysis of fragments. Finally the original picturecan be obtained through splicing and restoring in the order.

Tea has been a popular beverage since ancient time and accumulated a great deal of culture. In modern society, tea packaging design attracts a lot of attention. How to reflect the integration of traditional culture and modern culture from the perspectives of shape, pattern and color and cater to consumers needs at home and abroad and make the tea packaging fun has become the key of tea packaging design. The important function of packaging is to attract consumers’ attention and trigger their desire to buy the product. Through the visual design of packaging, it is a vital way to reflect the quality of tea, as well as increase the value of goods. Highlighting the characteristics of tea is the fundamental purpose of packaging. The color, pattern and text attribution are essential element in packaging, meanwhile it conveys the product information. The application of color, pattern and text and other factors in the study make the tea more competitive. It exchanges information between tea and consumer. Good tea packaging can not only improve sales, but also enhance the brand image, and expand spread of traditional tea culture.

Copper-nickel alloys have been used in many applications in marine environments because of excellent corrosion and biofouling resistance. . This investigation is cover a review of many previous studies about the behavior of these alloys in marine environments with different environmental conditions including the effect of sulphur contamination, the effect of CO2, the effect of chlorine, the effect of flow velocity, the effect of temperature and the effect of adding some alloying elements to the alloy itself. There have been conflicting results in the past about the corrosion rate values and the chemical analysis of the corrosion films in different environmental conditions. More research is needed for studying the behavior of these alloys in marine environments to provide good assessment of the corrosion resisting characteristics.

Compared with the lithography and traditional technology, ink-jet printing technology has huge advantages such as reducing costs, improving production efficiency and reducing environment damage. The silver nanoparticles conductive ink used as core material in ink-jet printing technology has been greatly developed. At present, the conductive inks for printed circuit usually has high sintering temperature, low adhesion, poor mechanical properties, high cost, which limit the further industrial application. In this paper, nano silver pulp was prepared through liquid phase reduction method, and a self-made protective agent ensured that the particle size distribution of silver particles is about 5nm. The above silver pulp was dispersed in the organic resin to get conductive ink with 20% (wt%) silver content. Under 170°Csintering, the electrical conductivity of the ink layer was 1.15×104S/m.

This paper proposed an improved method based on adaptive with threshold wavelet transform denoising, according to image is often affected by noise pollution in the process of acquisition and transmission, compared with the advantages and disadvantages of traditional digital filtering method. It extracts the structure information and details of the image. It can adaptively select wavelet transform of optimal decomposition level and soft threshold to achieve the optimal noise reduction effect. The Simulation results demonstrate that this theory can effectively filter Gaussian noise and Salt and pepper noise, at the same time well protect the image details and achieve better visual effects.

The contribution deals with the possibilities of the use of existing commercially available vectorization programs for recognition drawing entities in raster graphics format obtained by scanning of the engineering drawing. Drawing entities as a line (solid, dashed, dot-dashed etc.), dimension, hatch, various symbols, text, etc., have specific semantic for the designer defined by standards. Expert knows to interpret this graphic language and he knows to create a mental model of the real object. To be able interpret digital content of the engineering drawing obtained by scanning by the form of 3D computer model often requires to perform many intelligent operations. In the first step it is necessary to obtain such vector representation of the scanned drawing to be able to identify the original drawing entities. Suitability of using the contemporary commercial vectorizing programs for engineering drawings was verified on the test sample of the drawing entities and the results are published in the paper.

In this paper, Genetic Algorithm (GA) method has been applied in the moisture control system for auto tuning (PID) parameters. Proportional – Integral – Derivatives control scheme is used to provide an efficient and quiet easier in control engineering applications. Most of the PID tuning methods are used as manually which is difficult and time consuming. Genetic Algorithm which leads to improve the efficiency of tuning of process. The proposed algorithm is used to tune the PID parameters and its performance has been compared with Fuzzy logic techniques.Compare to the fuzzy logic technique dynamic performance specfications such as rise time, peak time and peak overshoot optimal values produced by GA. The plant model represented by the transfer function is obtained by the system identification tool box.

Proportional – Integral – Derivatives control scheme is used to provide an efficient and quiet easier in control engineering applications. Most of the Conventional PID tuning methods are used in manually which is difficult and time consuming. Soft Computing Technique is used to overcome this problem by using Fuzzy logic technique. In this research focuses dynamic performance specification is such as rise time, settling time and peak over shoot. This paper proposes to compare conventional and non-conventional techniques and the result of this comparison, The non-conventional technique (Fuzzy logic) has optimal dynamic performance. The plant model is represented by the transfer function, is obtained by the system identification tool box.

A novel method of direct aniline multi-interfacial polymerization on paper substrate is introduced in this paper. Cellulose base papers with and without PAE reinforced were discussed. The PANI-paper composites after more than 3 polymerizations had much lower surface resistivity. Their mechanical strength and thermal stability were analyzed by tensile test and GTA. FTIR results explained that there was strong interaction between NH groups in aniline monomers and OH groups in fibers. Conductive composites made with PAE treated paper had both good thermal stability and good mechanical strength with high conductivity.

With the recognition of sustainable development improving gradually, low carbon campus construction has become a trend in international society. The ecological footprint model is a kind of effective method to measure the sustainable development and have some reference for low carbon campus study. Our case study is the ecological footprint of paper consumption in Dalian University of Technology, China. The results show that nearly 481.60 hm2 of ecologically productive lands were needed to support paper consumption and this means that the land consumed by the university is 2.28 times larger than its physical or built-up land. Within 2011 academic year, the reused paper flow was added up to 237.69 tons, of which library contributed the most with 164.98 tons and the remaining 72.71 tons came from secondhand books obtained from last academic year 2010, finally saved nearly 578.33 hm2 of forest land.

For the regular rectangular paper scraps recovery problem, at first, I used the edge detection based on the improved wavelet analysis to numerically describe the outline of words on each of the pieces. Secondly, screening according to the line spacing to find out paper scraps which are located in the edge. Thirdly, do initial matching to select the best line as a benchmark for two-dimensional double match splicing. At last, I used two-dimensional double match to make the whole stitching come out. In this paper, the data would use the 2013 China National University Mathematical Modeling Competition topic B official data. The model not only can solve the problem of this article, also can be used to solve the problem of similar cutting conditions.

Most of the scientific research engines utilize the same way to rank scientific research papers (SRP), this way is highly depend on the citation network. The retrieved results of these engines for any keyword contain old papers with the highest citation value. In this paper, we proposed a new and easy to implement ranking algorithm for scientific research papers known as Paper Time Ranking Algorithm (PTRA). PTRA is a new ranking algorithm that depends on three factors to rank its results; paper age, citation index and publication venue. To construct and prove our ranking algorithm we created a web crawler that crawl different scientific search papers databases in the world to collect the information that PTRA needs. Unfortunately, some of this information was missing, such as, the impact factor of the journals. To collect this information, we created another crawler that search the Internet for these journals impact factors. However, to prove our ranking algorithm results, we have compared PTRA with Google scholar ranking algorithm. We used Google scholar, since it has more than 50 million papers and its own system can gather and collect papers in a faster way. Our comparison results show that, citation index has the highest impact on Google scholars ranking algorithm results. Unlike PTRA that gains the paper age a higher impact on the ranked results. However, PTRA depends on the citation index and publication venue to rank the results but with less impact than the paper age.

An effective method of trajectory reconstruction is presented in order to identify aerodynamic parameters. A novel smoother URTSS, which can get more optimal ballistic parameters, is introduced because of the biggish error caused by the uncertain initial conditions. Finally the validity of the method is verified by the experimental data. It also proves that URTSS can improves the accuracy of the identification of aerodynamic parameters.

Based on the database of Thomson Reuters, the bibliometric and patent information of China and US in the field of Building Energy Efficiency from 2006 to 2011 are searched. The R&D capacity of China and US in the field of Building Energy Efficiency are compared, the advantageous institutes in this field are identified. The cooperation trend between China and US on Building energy efficiency is analyzed. Some suggestions are proposed based on the data analysis.

It was found that slagging in high temperature zone is one of the major problems in the refinery, petrochemical, pulp and paper, and steel industries; especially in biomass and coal pulverized power plant. Slagging conditions are critical factors influencing reliability and availability on a biomass utility boiler. In this study, several types of slagging were collected for chemical analysis. It was revealed that the chemical composition and other properties of received slagging showed unique results based on the type of feedstock fuel materials.

India is a fastest growing major economy in 2018, with a growth rate of 7.4 per cent GDP. Energy use in developing countries like India has risen more than fourfold over the past three decades and is expected to continue increasing rapidly in the future. Energy is essential for a economical growth of any county. Biofuels derived from renewable resources will become a alternative supplement for the conventional energy sources in meeting the increasing requirements for transportation fuels. In the present paper, effort are made to evaluate the pongamia biodiesel of 20% Blend (PB20) with neat diesel as an alternative fuel for CI engine. The pongamia oil is converted into pongamia methyl esters (Biodiesel) using two step process Esterification and Transesterification. The fuel properties of raw pongamia methyl ester and blend (PB20) are evaluated as per ASTM/BIS standards to check their feasibility as an alternative fuel. The prepared blend is used to run the computerized CRDI diesel engine at different load conditions. From the experimental investigation made, PB20 has a potential to be as an alternative fuel for diesel engine. The performance of PB20 with respect to Brake Thermal Efficiency (BTHE), Mechanical Efficiency, Brake Mean Effective Pressure (BMEP) and Specific Fuel Consumption (SFC) is comparatively low when compared to neat diesel. The P-Ɵ and P-V diagram shows that the combustion of PB20 is as similar to that of neat diesel.

Ramie solid waste as chips can be used as raw material for pulp. Ligninolytic enzymes of laccase widely used for pretreatment of the pulping process of ramie chips by biodelignification using laccase produced byPenicilliumsp. LX/08 has been done. This study aims to obtain optimal concentrations of lignin and CuSO4as enzyme inducers to increase laccase production fromPenicilliumsp. LX/08 during biodelignification process and its effect on the quality of ramie pulp. The biodelignification process of ramie chips was carried out by solid state fermentation (SSF) method with six days incubation time. Two inducer type treatment factors (CuSO4and lignin), and variations in the concentration of each lignin (0.25 g/L, 0.5 g/L, 0.75 g/L) and CuSO4(0.25 mM, 0.5 mM, 0.75 mM) were investigated in this study. The pulping process was carried out by the soda process in a digester under conditions: 12% active alkaline, temperature of 165°C for 3.5 hours. The results showed that 0.75 mM and 0.5 g/L of lignin were the optimal concentrations which could increase the laccase activity ofPenicilliumsp. LX/08 by 343 U/L and 25,8 U/L, respectively. The quality of ramie pulp showed a decrease in Kappa Number of 9,34% with an increase in pulp yield to 55,43%. Based on these results, the pretreatment method using laccase produced byPenicilliumsp. LX/08 can assist the pulping process of ramie.

Spent catalyst is listed as one of the hazardous wastes. Based on the toxicity characteristic shows that spent catalyst contains some heavy metals at concentration above the regulations limits. This situattion becomes an important issue in nowadays. In this research, fungus Aspergillus niger was investigated to produce weak organic acid (citric acid). Batch experiments were performed to compare the leaching efficiency from spent catalyst of pulp density (2% and 4%) and particle size (212 µm, 150 µm and 75 µm). Result showed that after direct bioleaching process, maximum recovery of valuable metal 24.94%, 7.42%, 1.09%, 3.51%, 4.87% and 1.66% were achieved for aluminum, calcium, iron, copper, silver and platinum respectively at 2% pulp density. Overall data shows that metal recovery at pulp density 2% are higher than 4% pulp density. The maximum recovery based on particle size shows that the smaller particle (75 µm) the higher metal recovery (Al, Ag and Pt) and for some metals was different such as Fe, Cu and Ca.

This study was carried out to investigate the effect of beating process to the characteristics of pulp and paper produced from oil palm oil male flower spikes (OPMFS). OPMFS pulp was prepared according to chemical Soda-AQ pulping process. 60 gsm handsheet of oil palm male flower spikes paper were prepared from OPMFS pulp with four different beating times which are 0 revolution, 1000 revolutions, 2000 revolutions and 3000 revolutions. All physical and mechanical characteristics were investigated according to TAPPI and MS ISO standards. The results show that overall physical and mechanical characteristics of POMFS paper were influenced and enhanced by beating process between 0 until 3000 revolutions. This research demonstrate some potential characteristics of palm oil male flower spikes (OPMFS) paper to be investigated as a newly explored non-wood based raw material for papermaking raw material for papermaking.

In this paper, the cockle shell was studied as a catalyzer for biodiesel production. The cockle shell was heated at the various temperatures from 200 to 1300 °C for 4 h in the furnace. Then, the crystal structure and function group of unheated and heated cockle shell were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR), respectively. The results indicated that the initial phase of cockle shell is aragonite phase. After heat at 400 °C, the aragonite phase transformed to calcite phase. Moreover, the calcite phase of cockle shell was completely changed to calcium oxide (CaO) after heated at 800 °C. Eventually, the yield of biodiesel used the CaO derived from cockle shell were determined by nuclear magnetic resonance spectroscopy (NMR). The results show that the CaO derived from cockle shell can be used as a catalyzer of biodiesel preparation. However, the biodiesel used CaO from cockle shell after heated at 1100 to 1300 °C as a catalyzer have the higher yield than other heated temperature. Finally, the results of this research indicated that the CaO from cockle shell could be used as a catalyst for biodiesel production.

Biomass fly ash is an ash combustion product. It is composed of the particulates (fine particles of fuel) driven out of biomass-fired boilers together with the flue gases. The understanding of the behaviour and property of fly ash is very important in order to predict the consumable part lifetime inside industrial boiler system. In this research study, the several characterization processes were carried out. It was revealed that biomass fly ash obtained from different sources presented unique property and more results were displayed in experimental result section.

Three procedures for protein extraction in longan pulp had been applied to analyze protein pattern and quality of Longan pulp (Dimocarpus longan Lour. cv. Daw) during fruit growth to increase protein expression in proteomic analysis at Maejo university’s farm. There were data points to compare between normal and physiological disorder syndromes during fruit growth (5,10, 15, 20, 25 and 30 weeks, respectively) by one dimensional electrophoresis (1-D gel) technique in reducing condition. The first protein extraction, M1 (95% ethanol) showed obviously 15 protein bands which molecular weights were 14.97, 17.90, 18.30, 21.63, 28.54, 31, 33.96, 35.02, 42, 51.69, 65.69, 71.54, 88.02, 106.86 and 130 kDa, respectively. While M2 extraction (phenol-methanol/ammonium acetate) and M3 extraction (1.5 mM tris-HCl pH 8.0, 5 mM EDTA, 2% SDS) had low protein expression and no sharpness (13 and 12 protein bands, respectively). In different extraction conditions, therefore, M1 was a suitable method because of highest protein bands and obvious protein expression on longan pulp for proteomic analysis. Proteomic analysis of M1 extraction method was used in protein analysis by using LC-MS / MS techniques. It was found that the heat shock protein 83 (81.0 kDa), a family of proteins that was produced by cells in response to exposure on stressful conditions, the elongation factor 1-alpha (49.45 kDa), a selective regulator of translation, and the peroxidase 4 (39.74 kDa), a protein that is involved in the degeneration or aging of cells. These proteins exhibited a darker appearance of the protein bands at 30 weeks. Moreover, a partial glyceraldehyde-3-phosphate dehydrogenase (34.06 kDa), the protein involved in metabolic processes in glucose degradation, was also founded a darker appearance at 25 weeks and low appearance at 30 weeks of abnormal longan. However, higher proteomic techniques should be studied to confirm this biomarker protein in the further.

This study aims to investigate appropriate utilization of mixing grease waste (GW) from a canteen’s grease trap with bamboo residues charcoal (BC) to produce briquette fuel in the various ratio by weight, 1:2, 2:2, 3:2 and 4:2 (GW:BC). The physical and chemical properties of briquette fuel were analyzed to verify its heating value components as specified by the American Society for Testing and Material (ASTM). The results showed that the mixture of all components could produce charcoal briquette fuel. The GW:BC mixing ratios 3:2 and 4:2 have heating values exceeding the minimum requirement under the Thai Community Product Standard (tcps 238/2004). The briquettes mixing ratio of 3:2 was suitable for utilization. The heating value high to 7,938 cal/g on a dry basis.The charcoal briquette mixed with grease waste can be a feasible alternative energy source for incinerating which minimize to reduce waste.

This study was carried out to investigate the characteristics of pulp and paper produced from oil palm oil male flower spikes (OPMFS). The evaluation of the pulping process was studied based on the chemical Soda Anthraquinone pulping process. 60 gsm papersheet of oil palm male flower spikes were prepared from unbeaten and unbleached OPMFS Soda-AQ pulp. All optical, physical and mechanical characteristics were investigated according to TAPPI and MS ISO standards. OPMFS pulp recorded value of 6.42 s, 353 ml, 76.5 %, 36.7 % and 9.35 for drainage time, freeness, moisture content, screened yield percentage and Kappa number respectively. OPMFS paper sheet recorded value of 56.99 g/m2, 131.11 µm and 0.43 g/m3for grammage, bulking thickness and apparent bulk density respectively. Unbleached OPMFS paper also recorded 26.49 % and 43.50 % for brightness and opacity. For mechanical characteristics, OPMFS paper recorded 39.10 N.m/g, 8.32 mN.m2/g, 3.15 kPa.m2/g and 38.50 for tensile index, tear index, burst index and folding endurance (no.) respectively. This research demonstrate some potential characteristics of oil palm male flower spikes (OPMFS) paper to be investigated as a newly explored non-wood based raw material for papermaking.

This paper mainly investigate how to use cheaply-priced, safety and sanitate of natural clay or nanosilica as coagulant and adsorbent combined with polyaluminium chloride to treat low temperature and low turbidity water .Wastewater in paper mill was used as the water samples, by measuring the absorbance and the turbidity of the water samples to determine the flocculation effect. The results showed that flocculation effect of water samples with different natural clay and nanoSiO2combined with PAC had the same change tendency. The order of coagulation effects was bentonite > diatomite > kaolin > attapulgite. nano-SiO2as coagulant associated with PAC could attain best coagulation effect with least amount from the analysis of absorbance or turbidity.

In the paper experiments and theory of biogas production using industrial waste from paper production as a co-substrate are described. The main aim of the experiments was to evaluate the sensitivity and applicability of the biochemical conversion using the anaerobic digestion of the mixed biomass in the pilot fermentor (5 m3), where the mesophillic temperature was maintained. It was in parallel operation with a large scale fermentor (100 m3). The research was carried out at the biogas plant in Kolíňany, which is a demonstration facility of the Slovak University of Agriculture in Nitra. The experiments proved that the waste arising from the paper production can be used in case of its appropriate dosing as an input substrate for biogas production, and thus it can improve the economic balance of the biogas plant.

The goal of the paper is to determine a possibility to use methyl cameline esters and their mixtures with diesel oil (in ratios of 95:5, 90:10, 85:15, and 80:20) as fuels for compression-ignition engines (diesel engines). The cameline esters obtained in the result of one-step basic transesterification were characterised in respect of kinematic viscosity at 40°C, density at 15°C, acid number, solid impurities content, sulfur content, ignition temperature, temperature of cold filter clogging, and oxidation resistance at 110°C. It was shown that majority of factors of pure cameline esters analysed in the paper, excluding content of impurities and oxidation resistance, met the requirements of the PN-EN 14214, 2012 standard. Whereas, in case of mixtures of diesel oil with varied addition of esters, it was ascertained that 5, 10 and 15% addition of the biocomponent did not affect significantly the physico-chemical properties of the prepared fuel. In turn, the highest, 20% share of a cameline ester caused a slight increase in viscosity, density, content of impurities and ignition temperature of the obtained mixture. However, it is noteworthy that these factors did not exceed the acceptable values according to the standard. In general, it was also ascertained that the only parameter disqualifying use of these samples as a fuel for compression-ignition engines was too high content of impurities.

Current pulp-processing in pulp and paper based industries are inefficient in removing the lignin as this compound is recalcitrant towards degradation. Transitioning from conventional pulping process into bio-delignification through utilisation of ligninase enzymes is one of the alternatives to improve the ability to fully utilize all components of wood to produce high quality fibres. Extensive research efforts have been focused on increase the production of ligninase enzymes from white rot fungi as a whole organism for industrial applications. However, enzymes activity produced from fungi are rather low as lignin modification is a secondary metabolism in which the enzyme only be expressed under particular conditions. Using genetic manipulations to incorporate genes associate for delignification isolated from different organisms such as tropical Asian wood-feeding insect into bacteria expression system will allow rapid enzyme production. This theoretical framework aims to produce an enzyme with high ligninase activity that will be used for removal of lignin during pulp-processing. These enzymes are thought to be more economically efficient in degrading lignin and involves less use of chemicals thus make this processing more environmentally friendly.Keywords: Biodelignification, Asian wood tropical insect, fungi, ligninase enzyme, bacterial expression system

The aim of this work was to study the potential of the agricultural waste byproduct as a low-cost adsorbent for removal of phosphate ion (PO43-) from synthetic wastewater. The simple preparation of carbonized filter cake (CFC) was performed at 550°C. CFC was also characterized using FTIR, X-ray fluorescence analysis. The adsorptive parameters of batch experiment, such as pH of solution, dosage and contact time were systematically studied in order to the optimization condition. The optimum conditions of pH, contact time and adsorbent dose were to be 6, 60 min, and 2 g/L, respectively. The Langmuir and Freundlich isotherms were used to calculate the adsorption parameters that was able to describe the equilibrium isotherm and adsorptive mechanism. The maximum monolayer adsorption capacity of CFC was estimated as 20.32 mg/g. The optimized condition was applied for phosphate removal from synthetic wastewater. The achieved phosphate removal efficiency from synthetic wastewater sample was to be 92.4%. Filter cake is a low-cost byproduct of sugar cane but it can also highly effective remove phosphate ion from aqueous solution. The modification of filter cake surface via chemical reaction as a new adsorbent in order to increase surface sites and high affinity with phosphate ion will also be further studied.

This study used a sodium hydroxide (NaOH) solution to activate a mixture of water treatment sludge, fly ash, and slag, in order to produce a new alkali-activated controlled low-strength material (CLSM). Fresh properties of this new CLSM were investigated through the tests of workability, setting time, and ball drop time. Test results show that the addition of water treatment sludge (WTS) decreased workability. In addition, the addition of such WTS increased initial setting time and ball drop time, whereas the alkali equivalent (AE) shortened the initial setting time and ball drop time. At a liquid-to-solid ratio (L/S) of 0.9, a WTS content of 10%, and an alkali equivalent of 9%, the fresh properties for the CLSM conforms to the design principles and provisions of the Public Works Department, Taipei City Government, and is ideal for road construction in order to reduce traffic impact.

The depleting Fossil fuels reserves are caused to look into new Renewable energy sources to fulfill Diesel fuel demand in developing countries such as India. Increasing urbanization is lead to the search for new alternative sources like biodiesel. In India demand of diesel fuel in Industry and Transportation sector. To resolve all the above problems, researchers, scientists were produced biodiesel from first, second and third generation biodiesel sources. Among all the sources Algae was the most Oil rich sources. The byproducts in algae to biodiesel conversion process are most valuable than other. In the present work author tried to work in a new approach, i.e. the mixed culture algae particles are emulsified in pure Coconut biodiesel fuel by using TritonX-100 as a surfactant to prepare an emulsified fuel. This fuel sample was applied to DI CI engine to improve performance, emission characteristics. The experimental results were shown that there is the improvement in diesel engine performance; emission characteristics especially break thermal efficiency and NOx emission reduction than diesel fuel due to its clean combustion.

Biomass-derived materials such as kenaf pulp and wood chips are a perfect candidate to produce magnetic paper. Furthermore, by using biomass waste, such as paddy straw, sugarcane, bagasse and durian shell, the cost of producing magnetic paper can be further reduced while giving added value to the waste. This paper investigates the potential of producing magnetic sheet from durian shell. Initially, durian shells were dried before undergoing the pulping process. The resulted sheet was then combined with magnetic particles, the nano magnetite using either lumen loading or in-situ co-precipitation to produce a magnetic composite sheet. After being loaded with magnetic particles, the composite sheets were tested in terms of the homogeneity of the magnetic particles in the samples, degree of loading of the magnetic particles and the magnetic properties of the samples. Results obtained show a great success in producing the magnetic sheet from durian shell waste and nano magnetite particles. It was also found that the lumen loading method gives better magnetic properties compared to the in-situ co-precipitation method.

This paper discusses the effects of different retention agent such as: CPAM, APAM, PAE+CPAM, cationic starch with high degree of substitution and modified starch on the reversible thermochromism materials in anti-counterfeiting paper retention rate, and then determined the optimum dosage of retention agent in the slurry. According to the anti-counterfeit paper color value, the mechanism of reversible thermochromism paper was studied. The experimental results show that when the slurry with retention agent, the reversible thermochromism materials in the anti-counterfeit paper retention increased significantly. This suggests that retention agent in pulp fiber has played the role of bridge and link, thus ensuring the security of reversible thermochromism paper.

This paper focuses on the study of a series of photoinitiators (PIs) present in a set of two paper and board samples which have different composition, grammage and thickness. The chemical compounds released by the paper packaging can contaminate food and may affect the safety and health of consumers.To evaluate if the paper and board could be used as food packaging material, partition coefficients (Kpaper/air) between paper and air of six kinds of PIs in white carton board and kraft paper were determined. The results indicated that Values of Kpaper/air from 1 to 4843 were obtained at different temperatures. Kpaper/air decreases with temperature increasing, and the value is proportional to grammage and thickness of the paper samples. The lower of the grammage and the thickness,the lower of Kpaper/air value will be. The Kpaper/air value of 2-ethylhexyl-4-dimethylaminobenzoate (EHDAB) is the lowest, and the Kpaper/air value of 4-methylbenzophenone (MBP) is the highest.It shows that the Kpaper/air value depends on the boiling point of the chemical compounds, the chemical properties and the type of the paper sample.

In this study a high viscous liquid fuel, approximately 20 times more than that of diesel, produced from non- edible oil seed jatropha curcaswhich has been considered as an alternative fuel for the compression ignition engine is reduced through trans-esterification process. During this process, the raw jatropha curcas oil is preheated to 60°C and treated with methanol 20% by volume along with potassium hydroxide (KOH) by 0.568% of the oil weight as alkaline catalyst at 60°C reaction temp to produce Methyl Esters of Jatropha Oil (JOME). Similarly, the above method is followed to produce Ethyl Esters of Jatropha Oil (JOEE) with preheating at 70°C. In addition, 2% glycerol is added to the mixture to improve the reaction rate. The lower viscous fuel biodiesel (JOME and JOEE) produced by trans-esterifying of jatropha oil is blended with pure diesel 50% by volume. An experimental investigation have been carried out without altering the CI engine to examine the performance parameters in terms of brake thermal efficiency, total fuel consumption and brake specific fuel consumption for several engine load from 0 Kg to 8 Kg. The study also includes, separation of crude biodiesel from glycerol, washing of crude biodiesel, examination of calorific value using bomb calorimeter, viscosity measurement using redwood and brookfield viscometer, engine emission test and cost comparison for production of one litre of JOME and JOEE. It is inferred from the above study that the blends of JOME with diesel have closer performance to diesel when compared to the blend of JOEE with diesel. But, on comparison of their exhaust emission, the JOEE showed reasonable lower exhaust emission CO and NOx in spite of its higher calorific value when compared with JOME. The study also revealed that the biodiesel can be adopted as an alternative fuel for existing diesel engine without any modification.

Natural indigo dye was applied on silk fabric by using pad-batch and pad-dry techniques in the present of thiourea dioxide and sodium hydroxide. Alum (AlK(SO4)2), ferrous sulfate (FeSO4), and stannous chloride (SnCl2) were used as mordants. The colour of each dyed fabric was investigated in terms of the L*, a*, b* and K/S values. The effects of different dye concentrations with the use of applying padding techniques in the dyeing process was investigated. The colour fastness to washing, light, rubbing, water, and perspiration of dyed silk fabrics was performed according to the present ISO standard. Silk fabric was dyed by using a natural indigo colourant, applying one with metal mordant and one without giving the silk fabric a blue shade. However, a greenish blue shade was found as a dyeing result by adding a ferrous sulfate mordant. The fastness properties of washing, water, perspiration, and rubbing were very good level. However, a fair rating level was observed using a light fastness dyeing technique.

Soil contamination with used lubricating oil from automobiles is a growing concern in many countries, especially in Asian. This research was conducted on a laboratory scale. The plant used in this research was Spathiphyllum spp. in comparison with controlled (no-plant). The size of reactor used in this research was set at 20 cm width, 20 cm length, and 40 cm height with working volume of the reactor was 0.016 cm3. Moreover, a pH value was controlled in a range of 7 to 8. The soil contaminated with used lubricant oil collected from automobile shop in Nonthaburi province. Soil contaminated and treated soil were extracted by solid-phase extraction (SPE) and analyzed by gas chromatography with mass spectrometer (GC–MS). The results showed that Spathiphyllum spp. could be growth during time operation. Spathiphyllum spp. has a potential in reclaiming hydrocarbon-contaminated soil such as Benzene, Toluene, Ethylbenzene, and Xylene (BTEX) approximately 20 to 60 days operation.

Spent coffee grounds (SCGs) are created in a large amount as a processing waste during making the coffee beverages. Due to its properties, this waste is attractive for different applications such as biofuel production, antioxidant capacity, and renewable materials. In this study, the SCGs were firstly washed by distilled water to remove impurities and contaminations. The washed SCGs were dried in an electric oven at 120 °C for 24 h. The dried SCGs were carbonized at various temperatures from 600-1400 °C for 4 h in normal atmosphere by electric furnace to produce the SCGs powders. The as-received powders were characterized to obtain composed elements and phases by Energy-dispersive X-ray spectroscopy (EDX/EDS) and X-ray diffraction (XRD), respectively. X-ray analysis results indicated that the obtained SCGs powders were dominated by carbon-rich phase with stronger bonding at higher carbonizing temperature. This finding was recommended that the SCGs could be considered as a possible candidate of the environmentally friendly materials to prepare and develop the biomass fuel generation.

The plywood production from coconut coir fiber and water hyacinth was investigated to reduce the residue and be increased of value and to reduce the use of natural wood by using coir and water hyacinth which are pressed to be plywood production. LA - 35A TOA glue and natural powders were used for plywood adhesive. The plywood tests were found in this research. The water absorption, density, and bending strength test as per Japanese Industrial Standard (JIS A 5905) were evaluated in this research. The results showed that coconut coir fiber was suitable for plywood production and contained 1.93 percent of moisture content, 0.52 g per cm3 of density, and 86.5 percent of water absorption and 11.9 MPa of bending strength. The result showed that water absorption value of plywood made from coconut coir fiber and water hyacinth was quite high and this product suitable for use only indoor furniture. Moreover, these research was studied the biodegradation of plywood products that made from coconut coir fiber and water hyacinth.

Biomass biodegradable packaging material as a new green packaging material is a hot research area of packaging material. In order to obtain its life cycle environmental property, the life cycle environmental impact of biomass biodegradable packaging materials was studied in this paper. Firstly, the life cycle assessment theory and Eco-indicator99 method were used to establish the life cycle assessment model for biomass biodegradable packaging material; Secondly, objective and scope of the assessment are identified through the research on characteristics of life cycle stages of biomass biodegradable packaging material; Finally, Simapro software is used to do the biomass biodegradable packaging materials LCA and the comparative analysis with the corrugated cardboard, kraft paper, modified starch biodegradable plastics packaging materials.

This paper primarily presents on carbon dioxide mitigation by marine microalgae. Among the potential marine microalgae,Nannochloropsis oculatahas been identified as a promising species which can be utilized to reduce carbon dioxide concentration via photosynthesis process. The growth ofN. oculataand lipid synthesis for biodiesel production is influenced by various aspects. The aspects that are focused in this paper include light source and intensity, temperature, carbon dioxide concentration, and photobioreactor design. Besides, emerging technologies that are able to increase the efficiency of carbon dioxide reduction were also highlighted. As a whole,N. oculatamight play a key role in reducing the global carbon dioxide emission as well as enhancing the biodiesel production.

A model of risk trend assessment for metro tunnel crossing underground pipelines is proposed in this paper based on the partial connection number. This paper fully considered the certainty and uncertainty of the index and used "partial connection number method" to analyze the risk developing trend and its sort of metro tunnel crossing underground pipelines. A case study was performed on a metro tunnel engineering of Shenzhen Line 9. The results showed that this model considered the dynamic characteristics of risk, enriching the contents of risk assessment of underground engineering, which can provide a reference for the risk management.

Many machining operations e.g. turning, milling or grinding are dependent on the application of water-based metalworking fluids (MWF) which contribute significantly to their high level of performance. MWF in-use are exposed to a microbial contamination, which leads to a deterioration of water-based MWF components and can cause a premature failure of the whole coolant system. Expensive monitoring and the addition of biocides are needed to maintain the MWF quality and to reduce the microbial load, regardless of the potential risk for health and environment. To overcome these limitations, the paradigm shift of using microorganisms as a replacement for conventional MWF is investigated in this paper. Microbial cell components and some microbial inclusions are comparable to conventional MWF components like e.g. fatty acids or sulfur compounds. Due to this fact, it is possible to create a regenerative system on a microbiological basis for the substitution of conventional MWF components. In preliminary tribological investigations the basic lubrication properties of microorganisms and their potential as a replacement for conventional MWF were shown. The presented approach intends to investigate the influence of microbial cell counts, cells size and extracellular polymeric substances (EPS) on the lubrication behavior respectively. The results of the tribological tests show that especially microorganisms with a big cell volume or a high EPS productivity exhibit superior Brugger-values (up to 174%) compared to a highly concentrated conventional MWF (emulsion 10%) and indicate the great potential of microorganisms as a replacement for conventional MWF.

Searching for new sources of energy in order to minimize the dependence on fossil fuels and also to preserve the environmentmeets thenecessityfor finding effective solutions to the problem of waste generated in different production levels.In juice pulp processing industrylarge volumes of waste are produced daily and can contribute, with its burning, for energy production. Once it is necessary the removal of moisture from the residue, this study evaluate the conventional drying and microwave drying of the biomass generated by peels of orange, mango and passion fruit with initial mean moisture content higher than 75%. The experiments were performed in oven at a temperature of 150°C and the average time for an almost complete withdrawal of peels studied was 130min. For drying by microwave with power of 900W, the average time required for the total reduction in moisture was 8.5min. The drying Page model was adjusted by non-linear regression to data obtained with correlation coefficients in all cases greater than 0.955. The higher heating value was rated equal to 16,25kJ/g, 19,62kJ/g, 16,35kJ/g for the peels of orange, mango and passion fruit, respectively. The average energy consumption for the drying process in the oven was 81,25kJ/gevaporated water and 12,07 kJ/gevaporatedwaterin the process by microwave, which indicates that drying using microwave is a very interesting option.