Search

Multiplexed analysis in medical diagnostics is widely accepted as a more thorough and complete method compared to single-analyte detection. While analytical methods like polymerase chain reaction and enzyme-linked immunosorbent assay (ELISA) exist for multiplexed detection of biomarkers, they remain time-consuming and expensive. Lateral flow assays (LFAs) are an attractive option for point-of-care testing, and examples of multiplexed LFAs exist. However, these devices are limited by spatial resolution of test lines, large sample volume requirements, cross-reactivity, and poor sensitivity. Recent work has developed capillary-flow microfluidic ELISA platforms as a more sensitive alternative to LFAs; however, multiplexed detection on these types of devices has yet to be demonstrated. In the aftermath of the initial SARS-CoV-2 pandemic, the need for rapid, sensitive point-of-care devices has become ever clearer. Moving forward, devices that can distinguish between diseases with similar presenting symptoms would be the ideal home diagnostic. Here, the first example of a multiplexed capillary-flow immunoassay device for the simultaneous detection of multiple biomarkers is reported. From a single sample addition step, the reagents and washing steps required for two simultaneous ELISAs are delivered to spatially separated test strips. Visual results can be obtained in <15 min, and images captured with a smartphone can be analyzed for quantitative data. This device was used to distinguish between and quantify H1N1 hemagglutinin (HA) and SARS-CoV-2 nucleocapsid protein (N-protein). Using this device, analytical detection limits of 840 and 133 pg/mL were obtained for hemagglutinin and nucleocapsid protein, respectively. The presence of one target in the device did not increase the signal on the other test line, indicating no cross-reactivity between the assays. Additionally, simultaneous detection of both N-protein and HA was performed as well as simultaneous detection of N-protein and human C-reactive protein (CRP). Elevated levels of CRP in a patient infected with SARS-CoV-2 have been shown to correlate with more severe outcomes and a greater risk of death as well. To further expand on the simultaneous detection of two biomarkers, CRP and N-protein were detected simultaneously, and the presence of SARS-CoV-2 N-protein did not interfere with the detection of CRP when both targets were present in the sample.

Human exposure to heavy metals is a concerning global problem because of its detrimental effect on our health and ecosystem. Assessing the levels of these metals is cost- and labor-intensive and nonuser friendly because current analysis approaches typically rely on heavy instrumentations like inductively coupled plasma-mass spectrometry, which is only possible in centralized labs. Hence, simple economical detection methods are in high demand in developing countries and areas with insufficient infrastructure, professional experts, and appropriate environmental treatment. Several microfluidic paper-based analytical devices have been reported as promising alternatives to conventional testing methods for on-site heavy metal detection. Paper-based microfluidics are advantageous because of their simple fabrication, biodegradability, low cost, and ability to operate without pumps. However, typical assay times for current platforms are slow, and they typically rely on pipetting a fixed volume into the assay cards. This adds complexity in actual field scenarios. Here, we report a novel, inexpensive, and straightforward capillary-driven microfluidic device combined with paper for rapid and user-friendly detection of Ni(II), Cu(II), and Fe(III) in water. A colorimetric approach was adopted to quantify these metals. The device was able to produce a homogeneous color signal within 8 s of sample insertion. The limit of detection and limit of quantification were calculated to be 2 and 6.67 ppm for nickel, 0.3 and 1 ppm for Cu, and 1.1 and 3.67 ppm for Fe, respectively. The majority (>90%) of the collected samples showed recovery in the 80-110% range with acceptable accuracy and precision (<15% RSD) for a colorimetric device. This technique can be beneficial for rapidly assessing heavy metal exposure in drinking and surface water at drastically reduced assay time and is the first example of capillary flow-driven microfluidic devices as a transport medium for heavy metal detection.

It has been shown that short-chain fatty acids (SCFAs) produced by the gut microbiome are of importance to host tissue health; however, measuring such compounds in biological samples is often limited to using hours to days old fecal and blood plasma samples. Organ-on-a-chip models have been created to simplify the complexity but struggle to reproduce the full biology of the gut specifically. We recently reported a tissue-in-a-chip gut model that incorporates gut explanted tissue into a microfluidic device. The system maintains a biologically relevant oxygen gradient and tissue ex vivo for days at a time, but minimal characterization of biological activity was reported. Herein, we use 1 H-NMR to analyze the SCFA content of tissue media effluents from gut explants cultured in the recently developed microfluidic organotypic device (MOD). 1 H-NMR can identify key SCFAs in the complex samples with minimal sample preparation. Our findings show that maintaining physiologically relevant oxygen conditions, something often missing from many other culture systems, significantly impacts the SCFA profile. Additionally, we noted the changes in SCFAs with culture time and potential variability between SCFA levels in male and female mouse tissue explants cultured in the MOD system based on 1 H-NMR spectral profiles.

Urinary tract infections (UTIs) are one of the most common infections across the world and can lead to serious complications such as sepsis if not treated in a timely manner. Uropathogenic Escherichia coli account for 75% of all UTIs. Early diagnosis is crucial to help control UTIs, but current culturing methods are expensive and time-consuming and lack sensitivity. The existing point-of-care methods fall short because they rely on indirect detection from elevated nitrates in urine rather than detecting the actual bacteria causing the infection. Magnetophoresis is a powerful method used to separate and/or isolate cells of interest from complex matrices for analysis. However, magnetophoresis typically requires complex and expensive instrumentation to control flow in microfluidic devices. Coupling magnetophoresis with microfluidic paper-based analytical devices (μPADs) enables pump-free flow control and simple and low-cost operation. Early magnetophoresis μPADs showed detection limits competitive with traditional methods but higher than targets for clinical use. Here, we demonstrate magnetophoresis using hybrid μPADs that rely on capillary action in hydrophilic polyethylene terephthalate channels combined with paper pumps. We were able to detect E. coli with a calculated limit of detection of 2.40 × 10 2 colony-forming units per mL.

Point-of-care (POC) methods currently available for detecting SARS-CoV-2 infections still lack accuracy. Here, we report the development of a highly sensitive electrochemical immunoassay capable of quantitatively detecting the presence of the SARS-CoV-2 virus in patient nasopharyngeal samples using stencil-printed carbon electrodes (SPCEs) functionalized with capture antibodies targeting the SARS-CoV-2 nucleocapsid protein (N protein). Samples are added to the electrode surface, followed by horseradish peroxidase (HRP)-conjugated detection antibodies also targeting the SARS-CoV-2 N protein. The concentration of the virus in samples is quantified using chronoamperometry in the presence of 3,3'5,5'-tetramethylbenzidine. Limits of detection equivalent to less than 50 plaque forming units/mL (PFU/mL) were determined with virus sample volumes of 20 μL. No cross-reactivity was detected with the influenza virus and other coronavirus N proteins. Patient nasopharyngeal samples were tested as part of a proof-of-concept clinical study where samples were also tested using the gold-standard real-time quantitative polymerase chain reaction (RT-qPCR) method. Preliminary results from a data set of 22 samples demonstrated a clinical specificity of 100% ( n = 9 negative samples according to RT-qPCR) and a clinical sensitivity of 70% for samples with RT-PCR cycle threshold (Ct) values under 30 ( n = 10) and 100% for samples with Ct values under 25 ( n = 5), which complies with the World Health Organization (WHO) criteria for POC COVID-19 diagnostic tests. Our functionalized SPCEs were also validated against standard plaque assays, and very good agreement was found between both methods ( R 2 = 0.9993, n = 6), suggesting that our assay could be used to assess patient infectivity. The assay currently takes 70 min from sampling to results.

Thermoplastic electrodes (TPEs) are carbon composite electrodes consisting of graphite and thermoplastic polymer binder. TPE production is a solvent-based method, which makes it easy to fabricate and pattern into complex geometries, contrary to classical carbon composite electrodes. Depending on the composition (carbon type, binder, and composition ratio), TPEs can give excellent electrochemical performance and high conductivity. However, these TPEs are relatively new electrode materials, and thorough electrochemical characterization is still missing to understand and predict why large differences between TPEs exist. We used scanning electrochemical microscopy (SECM) as a screening tool to characterize TPEs. SECM data treatment based on scanning probe microscopy imaging allows a fast and easy comparison of the numerous images, as well as the optimization of the preparation. Experiments suggest that TPEs behave as a network of interacting microelectrodes made by electrochemically active islands isolated between less active areas. Higher carbon content in TPEs is not always indicative of more uniform electrodes with better electrochemical performances. Using various SECM redox probes, it is possible to select a specific graphite or polymer type for the analyte of interest. For example, TPEs made with COC:3569 are the best compromise for general detection, whereas PMMA:11 μm is better suited for catechol-like polyphenol analysis.

Exposure to trace metals in airborne particulate matter (PM) has been linked to various adverse health effects. Quantifying metals in PM is important; however, current analytical tools tend to be bulky and expensive. A need therefore exists for more rapid, low-cost, portable tools for multiplexed determination of metals in PM. Electrochemical paper-based devices (ePADs) have been used for detecting metals in PM but require different devices and methods for different metals, making the systems more complicated than desired. Recently reported Janus ePADs offer a solution to this problem by allowing for multiple electrochemical experiments from a single sample. Here, we sought to determine if a Janus ePAD containing four independent channels and working electrodes could be used for simultaneous detection of multiple metals in PM. Online sample pretreatment in each channel during sample delivery yielded optimal conditions for each experiment. The design allows the device to conduct square-wave anodic stripping voltammetry (SWASV) and square-wave cathodic stripping voltammetry (SWCSV) for simultaneous detection of Cd, Pb, Cu, Fe, and Ni from a single sample. Two detection zones each with shared reference and counter electrodes were used for SWASV and SWCSV, respectively. The proposed sensors reached LODs down to 0.5, 0.5, 1.0, 0.5, and 1.0 μg L -1 , for Cd(II), Pb(II), Cu(II), Fe(II), and Ni(II), respectively. The linear working ranges were 0.5-400.0 μg L -1 for Cd(II), Pb(II), and Fe(II), 1.0-400.0 μg L -1 for Cu(II), and 0.5-200.0 μg L -1 for Ni(II). The devices were applied for Cd(II), Pb(II), Cu(II), Fe(II), and Ni(II) determination in PM samples, and the results agreed with those using traditional ICP-MS analyses at 95% confidence.

Detecting bacteria is important in the fields of human health, environmental monitoring, and food safety. Foodborne pathogens alone are estimated to cause 420 000 deaths annually, with low-income regions affected most. Despite improvements in bacterial detection, fast, disposable, low-cost, sensitive, and user-friendly methods are still needed. Traditional methods for detecting bacteria rely primarily on cell culturing or polymerase chain reaction (PCR), which require highly trained personnel and a central laboratory and take several hours or even days to deliver results. Low-cost methods like lateral flow immunoassays exist but frequently suffer from poor sensitivity and/or lack quantitative results. Here, a rapid method for detecting bacteria at very low concentrations is presented using two sequential preconcentration steps. In the first preconcentration step, the sample is mixed with antibody-modified magnetic particles and free antibodies conjugated to β-galactosidase (β-gal). The target bacteria are isolated and concentrated using immunomagnetic separation. The isolated bacteria are then incubated with chlorophenol red-β-d-galactopyranoside (CPRG), which reacts with β-gal to produce chlorophenol red (CPR) in a bacteria concentration-dependent manner. In the second step, CPR and CPRG are separated and focused using an isotachophoretic microfluidic paper-based analytical device, significantly improving the final detection limit relative to paper-based devices lacking the focusing mechanism. Moreover, CPR and CPRG form two visible color bands that act as test and control bands, respectively, improving assay robustness. The method was tested with E. coli DH5-α and successfully detected concentrations as low as 9.2 CFU/mL in laboratory samples and 920 CFU/mL in apple juice samples in ∼90 min.

Microfluidic paper-based analytical devices (μPADs) are simple but powerful analytical tools that are gaining significant recent attention due to their many advantages over more traditional monitoring tools. These include being inexpensive, portable, pump-free, and having the ability to store reagents. One major limitation of these devices is slow flow rates, which are controlled by capillary action in the hydrophilic pores of cellulosic paper. Recent investigations have advanced the flow rates in μPADs through the generation of a gap or channel between two closely spaced paper sheets. This multilayered format has opened up μPADs to new applications and detection schemes, where large gap sizes (>300 μm) provide at least 169× faster flow rates than single-layer μPADs, but do not conform to established mathematical models for fluid transport in porous materials, such as the classic Lucas-Washburn equation. In the present study, experimental investigations and analytical modeling are applied to elucidate the driving forces behind the rapid flow rates in these devices. We investigate a range of hypotheses for the systems fluid dynamics and establish a theoretical model to predict the flow rate in multilayered μPADs that takes into account viscous dissipation within the paper. Device orientation, sample addition method, and the gap height are found to be critical concerns when modeling the imbibition in multilayered devices.

Electrochemical paper-based analytical devices (ePADs) have garnered significant interest as an alternative to traditional benchtop methods due to their low cost and simple fabrication. Historically, ePADs have relied almost exclusively on single electrode detection, limiting potential gains in sensitivity and selectivity achievable with multiple electrodes. Herein we describe incorporation of thermoplastic electrode (TPE) arrays into flow ePADs. Quasi-steady flow was solely generated by capillary action through a fan-shaped paper device. The electrode arrays were fabricated using a simple solvent-assisted method with inexpensive materials (i.e., graphite and thermoplastic binder). These electrodes can be employed as an array of individually addressable detectors or connected as an interdigitated electrode array. The TPEs were characterized through SEM, optical profilometry and cyclic voltammetry. Chronoamperometry was used to characterize the flow-based TPE-ePADs. Trace detection of a ferrocene complex (FcTMA + ) was demonstrated through generation-collection experiments, achieving a limit of detection of 0.32 pmol. These TPE arrays containing ePADs show great promise as a rapid, sensitive, and low-cost sensor for point-of-need (PON) applications.

This study describes the use of mass spectrometry imaging with matrix-assisted laser desorption/ionization (MALDI) and desorption electrospray ionization (DESI) to understand the color gradient generation commonly seen in microfluidic paper-based analytical devices (μPADs). The formation of color gradients significantly impacts assay sensitivity and reproducibility with μPADs but the mechanism for formation is poorly understood. The glucose enzymatic assay using potassium iodide (KI) as a chromogenic agent was selected to investigate the color gradient generated across a detection spot. Colorimetric measurements revealed that the relative standard deviation for the recorded pixel intensities ranged between 34 and 40%, compromising the analytical reliability. While a variety of hypotheses have been generated to explain this phenomenon, few studies have attempted to elucidate the mechanisms associated with its formation. Mass spectrometry imaging using MALDI and DESI was applied to understand the nonuniform color distribution on the detection zone. MALDI experiments were first explored to monitor the spatial distribution of the glucose oxidase and horseradish peroxidase mixture, before and after lateral flow assay with and without KI. MALDI(+)-TOF data revealed uniform enzyme distribution on the detection spots. On the other hand, after the complete assay DESI(-) measurements revealed a heterogeneous shape indicating the presence of iodide and triiodide ions at the zone edge. The reaction product (I 3 - ) is transported by lateral flow toward the zone edge, generating the color gradient. Mass spectrometry imaging has been used for the first time to prove that color gradient forms as result of the mobility small molecules and not the enzyme distribution on μPAD surface.

Viral pathogens are a serious health threat around the world, particularly in resource limited settings, where current sensing approaches are often insufficient and slow, compounding the spread and burden of these pathogens. Here, we describe a label-free, point-of-care approach toward detection of virus particles, based on a microfluidic paper-based analytical device with integrated microwire Au electrodes. The device is initially characterized through capturing of streptavidin modified nanoparticles by biotin-modified microwires. An order of magnitude improvement in detection limits is achieved through use of a microfluidic device over a classical static paper-based device, due to enhanced mass transport and capturing of particles on the modified electrodes. Electrochemical impedance spectroscopy detection of West Nile virus particles was carried out using antibody functionalized Au microwires, achieving a detection limit of 10.2 particles in 50 μL of cell culture media. No increase in signal is found on addition of an excess of a nonspecific target (Sindbis). This detection motif is significantly cheaper (∼$1 per test) and faster (∼30 min) than current methods, while achieving the desired selectivity and sensitivity. This sensing motif represents a general platform for trace detection of a wide range of biological pathogens.

In this study, paper-based microfluidic devices (μPADs) capable of K + quantification in aqueous samples, as well as in human serum, using both colorimetric and distance-based methods are described. A lipophilic phase containing potassium ionophore I (valinomycin) was utilized to achieve highly selective quantification of K + in the presence of Na + , Li + , and Mg 2+ ions. Successful addition of a suspended lipophilic phase to a wax printed paper-based device is described and offers a solution to current approaches that rely on organic solvents, which damage wax barriers. The approach provides an avenue for future alkali/alkaline quantification utilizing μPADs. Colorimetric spot tests allowed for K + quantification from 0.1-5.0 mM using only 3.00 μL of sample solution. Selective distance-based quantification required small sample volumes (6.00 μL) and gave responses sensitive enough to distinguish between 1.0 and 2.5 mM of sample K + . μPADs using distance-based methods were also capable of differentiating between 4.3 and 6.9 mM K + in human serum samples. Distance-based methods required no digital analysis, electronic hardware, or pumps; any steps required for quantification could be carried out using the naked eye.

Salmonella causes over a million foodborne illnesses per year in the United States resulting in more hospitalizations and deaths than any other foodborne bacterial pathogen. To help prevent outbreaks, a rapid, portable, sensitive, and reliable method for onsite detection of bacteria that can be used in different sample matrices would be beneficial. Herein, we present a colorimetric paper-based analytical device (PAD) combined with immunomagnetic separation (IMS) for detecting Salmonella typhimurium. IMS anti-Salmonella coated magnetic beads were applied to capture and separate bacteria from the sample matrix and preconcentrate it into small volumes before testing on paper. To directly detect S. typhimurium after IMS, a sandwich immunoassay was implemented into the procedure with β-galactosidase (β-gal) as the detection enzyme. Using the antibody/enzyme complex, we performed a colorimetric assay with chlorophenol red-β-d-galactopyranoside (CPRG) for bacteria quantification. The method was confirmed to be highly specific to S. typhimurium without interference from other pathogenic bacteria like Escherichia coli. Using this system, the limit of detection of S. typhimurium was found to be 10 2 CFU mL -1 in culturing solution without any pre-enrichment. In addition, distance-based detection where the concentration is read as the length of colored band formed on the reaction was also demonstrated. This assay had a detection limit of 10 2 CFU mL -1 for S. typhimurium, providing an instrument-free quantitative analysis alternative to spot tests, which require image analysis. Finally, the proposed platform was applied for detection of S. typhimurium in inoculated Starling bird fecal samples and whole milk with detection limits of 10 5 CFU g -1 and 10 3 CFU mL -1 , respectively, and this is the first published paper-based detection method for S. typhimurium in bird feces and whole milk.

The development of simple fluorescent and colorimetric assays that enable point-of-care DNA and RNA detection has been a topic of significant research because of the utility of such assays in resource limited settings. The most common motifs utilize hybridization to a complementary detection strand coupled with a sensitive reporter molecule. Here, a paper-based colorimetric assay for DNA detection based on pyrrolidinyl peptide nucleic acid (acpcPNA)-induced nanoparticle aggregation is reported as an alternative to traditional colorimetric approaches. PNA probes are an attractive alternative to DNA and RNA probes because they are chemically and biologically stable, easily synthesized, and hybridize efficiently with the complementary DNA strands. The acpcPNA probe contains a single positive charge from the lysine at C-terminus and causes aggregation of citrate anion-stabilized silver nanoparticles (AgNPs) in the absence of complementary DNA. In the presence of target DNA, formation of the anionic DNA-acpcPNA duplex results in dispersion of the AgNPs as a result of electrostatic repulsion, giving rise to a detectable color change. Factors affecting the sensitivity and selectivity of this assay were investigated, including ionic strength, AgNP concentration, PNA concentration, and DNA strand mismatches. The method was used for screening of synthetic Middle East respiratory syndrome coronavirus (MERS-CoV), Mycobacterium tuberculosis (MTB), and human papillomavirus (HPV) DNA based on a colorimetric paper-based analytical device developed using the aforementioned principle. The oligonucleotide targets were detected by measuring the color change of AgNPs, giving detection limits of 1.53 (MERS-CoV), 1.27 (MTB), and 1.03 nM (HPV). The acpcPNA probe exhibited high selectivity for the complementary oligonucleotides over single-base-mismatch, two-base-mismatch, and noncomplementary DNA targets. The proposed paper-based colorimetric DNA sensor has potential to be an alternative approach for simple, rapid, sensitive, and selective DNA detection.

Boron doped diamond (BDD) electrodes have exemplary electrochemical properties; however, widespread use of high-quality BDD has previously been limited by material cost and availability. In the present article, we report the use of a BDD paste electrode (BDDPE) coupled with microfluidic paper-based analytical devices (μPADs) to create a low-cost, high-performance electrochemical sensor. The BDDPEs are easy to prepare from a mixture of BDD powder and mineral oil and can be easily stencil-printed into a variety of electrode geometries. We demonstrate the utility and applicability of BDDPEs through measurements of biological species (norepinephrine and serotonin) and heavy metals (Pb and Cd) using μPADs. Compared to traditional carbon paste electrodes (CPE), BDDPEs exhibit a wider potential window, lower capacitive current, and are able to circumvent the fouling of serotonin. These results demonstrate the capability of BDDPEs as point-of-care sensors when coupled with μPADs.

The development of transparency-based electrochemical and paper-based colorimetric analytic detection platforms is presented as complementary methods for food and waterborne bacteria detection from a single assay. Escherichia coli and Enterococcus species, both indicators of fecal contamination, were detected using substrates specific to enzymes produced by each species. β-galactosidase (β-gal) and β-glucuronidase (β-glucur) are both produced by E. coli, while β-glucosidase (β-gluco) is produced by Enterococcus spp. Substrates used produced either p-nitrophenol (PNP), o-nitrophenol (ONP), or p-aminophenol (PAP) as products. Electrochemical detection using stencil-printed carbon electrodes (SPCEs) was found to provide optimal performance on inexpensive and disposable transparency film platforms. Using SPCEs, detection limits for electrochemically active substrates, PNP, ONP, and PAP were determined to be 1.1, 2.8, and 0.5 μM, respectively. A colorimetric paper-based well plate system was developed from a simple cardboard box and smart phone for the detection of PNP and ONP. Colorimetric detection limits were determined to be 81 μM and 119 μM for ONP and PNP respectively. While colorimetric detection methods gave higher detection limits than electrochemical detection, both methods provided similar times to positive bacteria detection. Low concentrations (10 1 CFU/mL) of pathogenic and nonpathogenic E. coli isolates and (10 0 CFU/mL) E. faecalis and E. faecium strains were detected within 4 and 8 h of pre-enrichment. Alfalfa sprout and lagoon water samples served as model food and water samples, and while water samples did not test positive, sprout samples did test positive within 4 h of pre-enrichment. Positive detection of inoculated (2.3 × 10 2 and 3.1 × 10 1 CFU/mL or g of E. coli and E. faecium, respectively) sprout and water samples tested positive within 4 and 12 h of pre-enrichment, respectively.

An electrochemical paper-based analytical device (ePAD) was developed for quasi-steady flow detection at microwire electrodes, for the first time. The device implements a fan shaped geometry connected to an analysis channel whereby solution is pulled from an inlet, through a channel, and into the steadily increasing capillary network of the fan. The network counteracts the decrease in solution flow rate associated with increasing viscosity within the channel, generating quasi-steady flow within the analysis channel. Microwire electrodes were embedded between two paper layers within the analysis channel, such that solution flow occurred on both sides of the wire electrodes. The quasi-steady flow ePAD increased the current by 2.5 times and 0.7 times from a saturated channel with no flow and from a single-layer paper device with flow, respectively. Amperometric detection was used for flow injection analysis (FIA) of multiple analytes at both Au and Pt microwire working electrodes, both of which provided similar sensitivity (ca. 0.2 mM -1 ) when normalized to the same standard. The two-layer paper devices provided a detection limit of 31 μM for p-aminophenol (PAP) using Pt electrodes and was also used to detect enzyme activity for the reaction of β-galactosidase with p-aminophenyl-galactopyranoside (PAPG). Measured enzyme kinetics provided similar V max (0.079 mM/min) and K m (0.36 mM) values as those found in the literature. This device shows great promise toward use in enzyme-linked immunosorbent assays or other analytical techniques where flow or washing steps are necessary. The developed sensor provides a simple and inexpensive device capable of performing multiple injection analysis with steady-flow and online detection that would normally require an external pump to perform.

The common selenium oxoanions selenite (SeO3(2-)) and selenate (SeO4(2-)) are toxic at intake levels slightly below 1 mg day(-1). These anions are currently monitored by a variety of traditional analytical techniques that are time-consuming, expensive, require large sample volumes, and/or lack portability. To address the need for a fast and inexpensive analysis of selenium oxoanions, we present the first microchip capillary zone electrophoresis (MCE) separation targeting these species in the presence of chloride, sulfate, nitrate, nitrite, chlorate, sulfamate, methanesulfonate, and fluoride, which can be simultaneously monitored. The chemistry was designed to give high selectivity in nonideal matrices. Interference from common weak acids is avoided by operating near pH 4. Separation resolution from chloride was enhanced to improve tolerance of high-salinity matrices. As a result, selenate can be quantified in the presence of up to 1.5 mM NaCl, and selenite analysis is even more robust against chloride. Using contact conductivity detection, detection limits for samples with conductivity equal to the background electrolyte are 53 nM (4.2 ppb Se) and 380 nM (30 ppb) for selenate and selenite, respectively. Analysis time, including injection, is ∼2 min. The MCE method was validated against ion chromatography (IC) using spiked samples of dilute BBL broth and slightly outperformed the IC in accuracy while requiring <10% of the analysis time. The applicability of the technique to real samples was shown by monitoring the consumption of selenite by bacteria incubated in LB broth.

The release of metals and metal-containing compounds into the environment is a growing concern in developed and developing countries, as human exposure to metals is associated with adverse health effects in virtually every organ system. Unfortunately, quantifying metals in the environment is expensive; analysis costs using certified laboratories typically exceed $100/sample, making the routine analysis of toxic metals cost-prohibitive for applications such as occupational exposure or environmental protection. Here, we report on a simple, inexpensive technology with the potential to render toxic metals detection accessible for both the developing and developed world that combines colorimetric and electrochemical microfluidic paper-based analytical devices (mPAD) in a three-dimensional configuration. Unlike previous mPADs designed for measuring metals, the device reported here separates colorimetric detection on one layer from electrochemical detection on a different layer. Separate detection layers allows different chemistries to be applied to a single sample on the same device. To demonstrate the effectiveness of this approach, colorimetric detection is shown for Ni, Fe, Cu, and Cr and electrochemical detection for Pb and Cd. Detection limits as low as 0.12 μg (Cr) were achieved on the colorimetric layer while detection limits as low as 0.25 ng (Cd and Pb) were achieved on the electrochemical layer. Selectivity for the target analytes was demonstrated for common interferences. As an example of the device utility, particulate metals collected on air sampling filters were analyzed. Levels measured with the mPAD matched known values for the certified reference samples of collected particulate matter.

This work presents a simple, low cost method for creating microelectrodes for electrochemical paper-based analytical devices (ePADs). The microelectrodes were constructed by backfilling small holes made in polyester sheets using a CO2 laser etching system. To make electrical connections, the working electrodes were combined with silver screen-printed paper in a sandwich type two-electrode configuration. The devices were characterized using linear sweep voltammetry, and the results are in good agreement with theoretical predictions for electrode size and shape. As a proof-of-concept, cysteine was measured using cobalt phthalocyanine as a redox mediator. The rate constant (k(obs)) for the chemical reaction between cysteine and the redox mediator was obtained by chronoamperometry and found to be on the order of 10(5) s(-1) M(-1). Using a microelectrode array, it was possible to reach a limit of detection of 4.8 μM for cysteine. The results show that carbon paste microelectrodes can be easily integrated with paper-based analytical devices.

A microfluidic paper-based analytical device (μPAD) fabricated by wax printing was designed to assess occupational exposure to metal-containing aerosols. This method employs rapid digestion of particulate metals using microliters of acid added directly to a punch taken from an air sampling filter. Punches were then placed on a μPAD, and digested metals were transported to detection reservoirs upon addition of water. These reservoirs contained reagents for colorimetric detection of Fe, Cu, and Ni. Dried buffer components were used to set the optimal pH in each detection reservoir, while precomplexation agents were deposited in the channels between the sample and detection zones to minimize interferences from competing metals. Metal concentrations were quantified from color intensity images using a scanner in conjunction with image processing software. Reproducible, log-linear calibration curves were generated for each metal, with method detection limits ranging from 1.0 to 1.5 μg for each metal (i.e., total mass present on the μPAD). Finally, a standard incineration ash sample was aerosolized, collected on filters, and analyzed for the three metals of interest. Analysis of this collected aerosol sample using a μPAD showed good correlation with known amounts of the metals present in the sample. This technology can provide rapid assessment of particulate metal concentrations at or below current regulatory limits and at dramatically reduced cost.

Foodborne pathogens are a major public health threat and financial burden for the food industry, individuals, and society, with an estimated 76 million cases of food-related illness occurring in the United States alone each year. Three of the most important causative bacterial agents of foodborne diseases are pathogenic strains of Escherichia coli , Salmonella spp., and Listeria monocytogenes , due to the severity and frequency of illness and disproportionally high number of fatalities. Their continued persistence in food has dictated the ongoing need for faster, simpler, and less expensive analytical systems capable of live pathogen detection in complex samples. Culture techniques for detection and identification of foodborne pathogens require 5-7 days to complete. Major improvements to molecular detection techniques have been introduced recently, including polymerase chain reaction (PCR). These methods can be tedious; require complex, expensive instrumentation; necessitate highly trained personnel; and are not easily amenable to routine screening. Here, a paper-based analytical device (μPAD) has been developed for the detection of E. coli O157:H7, Salmonella Typhimurium, and L. monocytogenes in food samples as a screening system. In this work, a paper-based microspot assay was created by use of wax printing on filter paper. Detection is achieved by measuring the color change when an enzyme associated with the pathogen of interest reacts with a chromogenic substrate. When combined with enrichment procedures, the method allows for an enrichment time of 12 h or less and is capable of detecting bacteria in concentrations in inoculated ready-to-eat (RTE) meat as low as 10(1) colony-forming units/cm(2).

The spatial and temporal distributions of an extensive number of diffusible molecules drive a variety of complex functions. These molecular distributions often possess length scales on the order of a millimeter or less; therefore, microfluidic devices have become a powerful tool to study the effects of these molecular distributions in both chemical and biological systems. Although there exist a number of studies utilizing microdevices for the creation of molecular gradients, there are few, if any, studies focusing on the measurement of spatial and temporal distributions of molecular species created within the study system itself. Here we present a microfluidic device capable of sampling multiple chemical messengers in a spatiotemporally resolved manner. This device operates through spatial segregation of nanoliter-sized volumes of liquid from a primary sample reservoir into a series of analysis microchannels, where fluid pumping is accomplished via a system of passive microfluidic pumps. Subsequent chemical analysis within each microchannel, achieved via optical or bioanalytical methods, yields quantitative data on the spatial and temporal information for any analytes of interest existing within the sample reservoir. These techniques provide a simple, cost-effective route to measure the spatiotemporal distributions of molecular analytes, where the system can be tailored to study both chemical and biological systems., (© 2011 American Chemical Society)

A microchip capillary electrophoresis (MCE) system has been developed for the determination of perchlorate in drinking water. The United States Environmental Protection Agency (USEPA) recently proposed a health advisory limit for perchlorate in drinking water of 15 parts per billion (ppb), a level requiring large, sophisticated instrumentation, such as ion chromatography coupled with mass spectrometry (IC-MS), for detection. An inexpensive, portable system is desired for routine online monitoring applications of perchlorate in drinking water. Here, we present an MCE method using contact conductivity detection for perchlorate determination. The method has several advantages, including reduced analysis times relative to IC, inherent portability, high selectivity, and minimal sample pretreatment. Resolution of perchlorate from more abundant ions was achieved using zwitterionic, sulfobetaine surfactants, N-hexadecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (HDAPS) and N-tetradecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (TDAPS). The system performance and the optimization of the separation chemistry, including the use of these surfactants to resolve perchlorate from other anions, are discussed in this work. The system is capable of detection limits of 3.4 +/- 1.8 ppb (n = 6) in standards and 5.6 +/- 1.7 ppb (n = 6) in drinking water.

A novel lab-on-paper device combining electrochemical and colorimetric detection for the rapid screening of Au(III) in the presence of a common interference, Fe(III), in industrial waste solutions is presented here. With dilute aqua regia (0.1 M HCl + 0.05 M HNO(3)) as the supporting electrolyte, square wave voltammetry on paper provided a well-defined reduction peak for Au(III) at approximately 287 +/- 12 mV vs Ag/AgCl. Under the optimized working conditions, the calibration curve showed good linearity in the concentration range of 1-200 ppm of Au(III) with a correlation coefficient of 0.997. The limit of detection (LOD) of the proposed method is 1 ppm. Interferences from various cations were also studied. Fe(III) is the only metal that affects the electrochemical determination of Au(III) when present above a 2.5-fold excess concentration of that of the Au(III). To overcome this limitation, a colorimetric method was used to simultaneously detect Fe(III) as a screening tool. The procedure was then successfully applied to determine Au(III) in gold-refining waste solutions. The results are in agreement with those obtained from inductively coupled plasma-atomic emission spectrometry (ICP-AES).

Semicontinuous monitoring of aerosol chemical composition has continually increased in demand because of the high spatial and temporal variability of atmospheric particles and the effects these aerosols have on human health and the environment. To address this demand, we describe the preliminary development of a semicontinuous aerosol composition analyzer consisting of a growth tube particle collector coupled to a microfluidic device for chemical analysis. The growth tube enlarges particles through water condensation in a laminar flow, permitting inertial collection into the microchip sample reservoir. Analysis is done by electrophoresis with conductivity detection. To avoid hydrodynamic interference from the sampling pressure, the microchip was operated isobarically by sealing the buffer reservoirs from the atmosphere and interconnecting all the reservoirs with air ducts. The collector samples at 1 L min(-1) and deposits particles into 30 microL of solution. Sample accumulates with time, and sequential injections are performed as aerosol concentration increases. For extended analyses, a sample rinsing system flushes the sample collection reservoir periodically. For inorganic anions, temporal resolution of 1 min and estimated detection limits of 70-140 ng m(-3) min were obtained. The system was used to measure sulfate and nitrate, and results were compared to a particle-into-liquid-sampler running in parallel. Results indicate that the prototype growth tube-microchip system (termed aerosol chip electrophoresis, ACE) could provide a useful complement to existing aerosol monitoring technologies, especially when less expensive and/or rapid analyses are desired.

We report the first demonstration of electrochemical detection for paper-based microfluidic devices. Photolithography was used to make microfluidic channels on filter paper, and screen-printing technology was used to fabricate electrodes on the paper-based microfluidic devices. Screen-printed electrodes on paper were characterized using cyclic voltammetry to demonstrate the basic electrochemical performance of the system. The utility of our devices was then demonstrated with the determination of glucose, lactate, and uric acid in biological samples using oxidase enzyme (glucose oxidase, lactate oxidase, and uricase, respectively) reactions. Oxidase enzyme reactions produce H2O2 while decomposing their respective substrates, and therefore a single electrode type is needed for detection of multiple species. Selectivity of the working electrode for H2O2 was improved using Prussian Blue as a redox mediator. The determination of glucose, lactate, and uric acid in control serum samples was performed using chronoamperometry at the optimal detection potential for H2O2 (0 V versus the on-chip Ag/AgCl reference electrode). Levels of glucose and lactate in control serum samples measured using the paper devices were 4.9 +/- 0.6 and 1.2 +/- 0.2 mM (level I control sample), and 16.3 +/- 0.7 and 3.2 +/- 0.3 mM (level II control sample), respectively, and were within error of the values measured using traditional tests. This study shows the successful integration of paper-based microfluidics and electrochemical detection as an easy-to-use, inexpensive, and portable alternative for point of care monitoring.

A new approach for improving the compatibility between contact conductivity detection and microchip electrophoresis was developed. Contact conductivity has traditionally been limited by the interaction of the separation voltage with the detection electrodes because the applied field creates a voltage difference between the electrodes, leading to unwanted electrochemical reactions. To minimize the voltage drop between the conductivity electrodes and therefore improve compatibility, a novel bubble cell detection zone was designed. The bubble cell permitted higher separation field strengths (600 V/cm) and reduced background noise by minimizing unwanted electrochemical reactions. The impact of the bubble cell on separation efficiency was measured by imaging fluorescein during electrophoresis. A bubble cell four times as wide as the separation channel led to a decrease of only 3% in separation efficiency at the point of detection. Increasing the bubble cell width caused larger decreases in separation efficiency, and a 4-fold expansion provided the best compromise between loss of separation efficiency and maintaining higher field strengths. A commercial chromatography conductivity detector (Dionex CD20) was used to evaluate the performance of contact conductivity detection with the bubble cell. Mass detection limits (S/N = 3) were as low as 89 +/- 9 amol, providing concentration detection limits as low as 71 +/- 7 nM with gated injection. The linear range was measured to be greater than 2 orders of magnitude, from 1.3 to 600 microM for sulfamate. The bubble cell improves the compatibility and applicability of contact conductivity detection in microchip electrophoresis, and similar designs may have broader application in electrochemical detection as the expanded detection zone provides increased electrode surface area and reduced analyte velocity in addition to the reduction of separation field effects.

New high-throughput immunoassay methods for rapid point-of-care diagnostic applications represent an unmet need and current focus of numerous innovative methods. We report a new micromosaic competitive immunoassay developed for the analysis of the thyroid hormone thyroxine (T4), inflammation biomarker C-reactive protein (CRP), and the oxidative damage marker 3-nitrotyrosine (BSA-3NT) on a silicon nitride substrate. To demonstrate the versatility of the method, both direct and indirect format competitive immunoassays were developed and could be applied simultaneously for single samples. Signals from standard solutions were fit to a logistic equation, allowing simultaneous detection of T4 (7.7-257.2 nM), CRP (0.3-4.2 microg/mL), and BSA-3NT (0.03-22.3 microg/mL). Total assay time including sample introduction, washing, and fluorescence measurement was less than 45 min. Dissociation constants for affinity pairs in the system have been estimated using regression. This proof-of-concept experiment shows that both small and macromolecular biomarkers can be quantified from a single sample using the method and suggests that groups of clinically related analytes may be analyzed by competitive micromosaic immunoassay techniques.

Microfluidic devices have gained significant scientific interest due to the potential to develop portable, inexpensive analytical tools capable of quick analyses with low sample consumption. These qualities make microfluidic devices attractive for point-of-use measurements where traditional techniques have limited functionality. Many samples of interest in biological and environmental analysis, however, contain insoluble particles that can block microchannels, and manual filtration prior to analysis is not desirable for point-of-use applications. Similarly, some situations involve limited control of the sample volume, potentially causing unwanted hydrodynamic flow due to differential fluid heads. Here, we present the successful inclusion of track-etched polycarbonate membrane filters into the reservoirs of poly(dimethylsiloxane) capillary electrophoresis microchips. The membranes were shown to filter insoluble particles with selectivity based on the membrane pore diameter. Electrophoretic separations with membrane-containing microchips were performed on cations, anions, and amino acids and monitored using conductivity and fluorescence detection. The dependence of peak areas on head pressure in gated injection was shown to be reduced by up to 92%. Results indicate that separation performance is not hindered by the addition of membranes. Incorporating membranes into the reservoirs of microfluidic devices will allow for improved analysis of complex solutions and samples with poorly controlled volume.

Biomarkers provide clinicians with an important tool for disease assessment. Many different biomarkers have been discovered, but few of them suffice as stand-alone indicators for disease presence or prognosis. Because no single biomarker can be relied upon for accurate disease detection there has been a substantial push for new multianalyte screening methods. Furthermore, there is a need to push assays toward a point-of-care technology to reduce the time between clinical analysis and medical intervention and minimize artifacts created during sample storage. There currently are, however, few inexpensive multianalyte methods for disease detection that can function in a point-of-care setting. A new approach which bridges the gap between traditional immunoassays and high-density microarrays by utilizing microfluidics, immunoassays, and micellar electrokinetic chromatography (MEKC) is discussed here. This chemistry, the cleavable tag immunoassay (CTI), is a low- to medium-density heterogeneous immunoassay designed to detect 1-20 analytes simultaneously. Although similar to traditional sandwich immunoassays, this approach is unique because the signal is not imaged on the surface; instead, a fluorescent tag is chemically cleaved from the antibody and analyzed by microchip MEKC. In this report, the CTI chemistry is used for the detection of four cardiac biomarkers elevated in acute myocardial infarction. Limit of detection (LOD) and dynamic range are reported for all biomarkers with LODs on the order of low nanograms per milliliter to low picograms per milliliter. Most importantly, the dynamic range for each of the biomarkers spans the boundary between normal and elevated levels. Finally, elevated marker levels were measured in spiked human serum samples.

Poly(dimethylsiloxane) (PDMS) has become one of the most widely used materials for microchip capillary electrophoresis and microfluidics. The popularity of this material is the result of its low cost, simple fabrication, and rugged elastomeric properties. The hydrophobic nature of PDMS, however, limits its applicability for microchip CE, microfluidic patterning, and other nonelectrophoresis applications. The surface of PDMS can be made hydrophilic using a simple air plasma treatment; however, this property is quickly lost through hydrophobic recovery caused by diffusion of unreacted oligomer to the surface. Here, a simple approach for the generation of hydrophilic PDMS with long-term stability in air is presented. PDMS is rendered hydrophilic through a simple two-step extraction/oxidation process. First, PDMS is extracted in a series of solvents designed to remove unreacted oligomers from the bulk phase. Second, the oligomer-free PDMS is oxidized in a simple air plasma, generating a stable layer of hydrophilic SiO2. The conversion of surface-bound siloxane to SiO2 was followed with X-ray photoelectron spectroscopy. SiO2 on extracted-oxidized PDMS was stable for 7 days in air as compared to less than 3 h for native PDMS. Furthermore, the contact angle for modified PDMS was reduced to <40 degrees and remained low throughout the experiments. As a result of the decreased contact angle, capillary channels self-wet through capillary action, making the microchannels much easier to fill. Finally, the modification significantly improved the performance of the devices for microchip electrophoresis. The electroosmotic flow increased from 4.1 x 10(-4) to 6.8 x 10(-4) cm(2)/V.s for native compared to oxidized PDMS. Separation efficiencies for electrochemical detection also increased from 50 000 to 400 000 N/m for a 1.1-nL injection volume. The result of this modification is a significant improvement in the performance of PDMS for microchip electrophoresis and microfluidic applications.

A simple and sensitive electrode design for microchip capillary electrophoresis/electrochemistry (CE-EC) is presented. The system employs metal microwires as the working electrodes for electrochemical detection. Two general approaches for integration of electrodes in microchip CE-EC are commonly used, end-channel and microfabrication. The end-channel approach allows electrode cleaning and the use of chemically modified electrodes; however, the designs generally lack portability and the ability to incorporate multiple electrodes. Microfabrication allows the incorporation of multiple electrodes on-chip and is easily made portable; however, it requires the use of expensive metallization and clean room facilities, and integration of more than one electrode material is challenging. The reported approach aligns a solid metal microwire through the separation channel allowing integration of multiple electrodes and the use of different electrode materials without sacrificing the portability. A detection limit of 100 nM for dopamine was achieved without the use of a decoupler as a result of a higher collection efficiency with the new design.

The separation and detection of underivatized carbohydrates, amino acids, and sulfur-containing antibiotics in an electrophoretic microchip with pulsed amperometric detection (PAD) is described. This report also describes the development of a new chip configuration for microchip electrophoresis with PAD. The configuration consists of a layer of poly(dimethylsiloxane) that contains the microfluidic channels, reservoirs, and a gold microwire, sealed to a second layer of poly(dimethylsiloxane). Example separations of carbohydrates, amino acids, and sulfur-containing antibiotics are shown. The effect of the separation and injection potentials, buffer pH and composition, injection time, and PAD parameters were studied in an effort to optimize separations and detection. Detection limits ranging from 6 fmol (5 microM) for penicillin and ampicillin to 455 fmol (350 microM) for histidine were obtained.

Electroosmotic flow (EOF) was monitored in glass microfluidic devices at rates up to 2 Hz with a precision of 0.2-1.0% using a technique based on the periodic photobleaching of a dilute, neutral fluorophore added to the running buffer. This EOF monitoring method was used to examine the performance of the current monitoring technique for measuring an average electroosmotic flow in a microfluidic device with a cross-T design. Flow measurements made with the current monitoring method gave a precision of 0.4-2.2%, but the periodic photobleaching method shows that the current monitoring technique causes changes in EOF as high as 41% during a single experiment. The periodic photobleaching method for EOF monitoring was also used to study EOF in channels on opposite sides of a cross-channel intersection. The opposite channels were shown to exhibit substantially different EOF dynamics during a current monitoring experiment as well as different steady-state EOF rates during normal operating conditions.

Poly(dimethylsiloxane) (PDMS) capillary electrophoresis (CE) microchips were modified by a dynamic coating method that provided stable electroosmotic flow (EOF) with respect to pH. The separation channel was coated with a polymer bilayer consisting of a cationic layer of Polybrene (PB) and an anionic layer of dextran sulfate (DS). According to the difference in charge, PB- and PB/ DS-coated channels supported EOF in different directions; however, both methods of channel coating exhibited a pH-independent EOF in the pH range of 5-10 due to chemical control of the effective zeta-potential. The endurance of the PB-coated layer was determined to be 50 runs at pH 3.0, while PB/DS-coated chips had a stable EOF for more than 100 runs. The effect of substrate composition and chip-sealing methodology was also evaluated. All tested chips showed the same EOF on the PB/DS-coated channels, as compared to uncoated chips, which varied significantly. No significant variation for separation and electrochemical detection of dopamine and hydroquinone between coated and uncoated channels was observed.

Construction and characterization of microfabricated recessed microdisk electrodes (RMDs) of 14- and 55-μm diameters and 4-μm depth are reported. For evaluation of electrode function, both faradaic current in Ru(NH(3))(6)(3+)/KNO(3) solution and charging current in KNO(3) solution were measured with cyclic voltammetry. The experimental maximum current was measured and compared to calculated values, assuming radial and linear diffusion. A model for diffusion to a RMD best matches the behavior of the 14-μm RMD, which has a larger depth-to-diameter ratio than the 55-μm RMD. At fast scan rates (204 V s(-)(1)), where linear diffusion should dominate, there are large deviations from the linear diffusion model. Uncompensated resistance and overcorrection for background current contribute to this deviation. The dependence of capacitance on scan rate of the RMDs was found to be similar to that of a macroelectrode, indicating good adhesion between the insulator and the electrode. Chronoamperometry of Ru(NH(3))(6)(3+) in KNO(3) in both static and stirred solutions was performed using the RMDs and the current is compared to those from a 10-μm-diameter planar microdisk electrode (PMD). The signal-to-noise ratio of the 14-μm RMDs compared to the PMD is on average 4 times greater for stirred solutions. The 55-μm RMD exhibited no protection to convection of the stirred solution.