Search

This work aims at understanding whether a citizen science-based monitoring system could be adequate to detect the effects, in terms of air quality, of solid and liquid fuel combustion for household heating. Citizen science is known to be able to improve the coverage and resolution of measurements at a very low cost. On the other hand, it also has severe limitations. Since low-cost sensors are to be used, measurements are problematic in terms of precision and accuracy. In order to test these aspects, we developed a system named COCAL that supports all the phases of air quality monitoring, from data acquisition, georeferencing, transmission, and processing up to web mapping. In this work, we focus on particulate matter. To address the limitations of the citizen science approach, we carefully tested all the parts of the system and, in particular, the performances of the low-cost sensors. We highlighted that their precision is acceptable, while their accuracy is insufficient. Measurements taken within such a paradigm cannot be used, therefore, as reference values. They can be used, instead, as relative values, in order to identify and to map trends, anomalies and hotspots. We used COCAL extensively in the city of Trieste and were able to identify different behaviors in different areas of the city. In the city center, PM values increase constantly during the day. In the rural suburbs of the city, we observed that PM values are low during the day but increase very rapidly after 5 p.m. It is important to note that, in the city center, household heating is based almost completely on natural gas. In the rural areas, household heating is generally based on wood burning stoves or liquid and solid fuel. A possible explanation of the different behavior between the two areas can then be related to commuters living in the rural areas but working in the city center. When they return home in the evening, they switch on the heating systems triggering the release of large quantities of particulate matter. We were able to map peaks of particulate matter values and highlight that they are initially located within the village centers to later propagate to the areas around them. The possibility of mapping air quality with the coverage and resolution we were able to obtain within a citizen science approach is very encouraging. This can be very helpful in understanding the impact that liquid and solid fuel combustion can have on the environment and human health. In addition, we think that this opportunity can be very important considering the current geopolitical situation where a (hopefully only temporary) shift toward pollutant fuels is expected in the near future.

International audience

Emissions from wood burning for heating in secondary homes or cabins is an important part in the development of high-resolution emissions in specific areas. Norway is used as case study as 20% of the national wood consumption for heating occurs in cabins. Our study first shows a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results in an increase in the cabin share to total heating emissions up to 25–35%. When comparing with regional emission inventories, our study shows that the gradient between rural and urban areas is not well-represented in regional inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

The report documents the updates made to the emission estimation model for residential wood combustion. The revisions included new estimates for the total number of wood stoves through the time series, new replacement rates for stoves and update to a number of emission factors taking the most recent measurement studies into account. The report also documents some of the uncertainties involved with estimating emissions from residential wood combustion and highlights potential future improvements.

The use of waste from the regional production of waste wood, waste paper, and cardboard in the form of briquettes may be causing an increase in local emissions, both of major elements and trace elements. When burning paper and cardboard briquettes, more than 70% of Mn, Zn, As, and Pb is released into the air from the total content of trace elements in the fuel. The largest amounts of major and trace elements are released when burning paper briquettes (56 g/kg of fuel), half of these amounts are released from burning briquettes from waste wood and coal (23 g/kg of fuel). The pursuit of alternative uses for those cardboard components that are not suitable for recycling cannot be directed to the production of briquettes for residential combustion in the framework of the application of the principles of the circular economy. In particular, the high concentrations of undesirable elements in the emissions released in the gas phase into the atmosphere are an obstacle existing even when the parameters of the PM10 emissions of a boiler are met. This is related to the high ash content of the cardboard (13.5%). Waste paper or cardboard could be added to waste wood at a maximum of 10% to make the pollution produced comparable to the burning of coal briquettes.

Summarization: Residential settings are of utmost importance for human exposure, as it is where people spend most of their time. Residential wood combustion is a widespread practice known as a source of indoor particulate matter (PM). Nevertheless, research on the risks of exposure associated with this source is scarce, and a better understanding of respiratory deposition of smoke particles is needed. The dosimetry model ExDoM2 was applied to determine the deposited dose of inhalable particulate matter (PM10) from residential biomass combustion in the human respiratory tract (HRT) of adults and children. The dose was estimated using PM10 exposure concentrations obtained from a field campaign carried out in two households during the operation of an open fireplace and a woodstove. Simultaneously, PM10 levels were monitored outside to investigate the outdoor dose in a rural area strongly impacted by biomass burning emissions. Indoors, the 8-h average PM10 concentrations ranged from 88.3 to 489 μg m−3 and from 69.4 to 122 μg m−3 for the operation of the fireplace and the woodstove, respectively, while outdoor average PM10 concentrations ranged from 17.3 to 94.2 μg m−3. The highest amount of the deposited particles was recorded in the extrathoracic region (68–79%), whereas the deposition was much lower in the tracheobronchial tree (5–6%) and alveolar–interstitial region (16–21%). The total dose received while using the fireplace was more than twofold the one received in the room with a woodstove and more than 10 times higher than in the absence of the source. Overall, indoor doses were higher than the ones received by a subject exposed outdoors, especially at the alveolar–interstitial region. After 24 h of exposure, it was estimated that approximately 35 to 37% of the particles deposited in the HRT were transferred to the gastrointestinal tract, while approximately 2.0–2.5% were absorbed into the blood. The results from exposure and dose of indoor particles gathered in this work suggest that homeowners should be encouraged to upgrade the wood burning technology to reduce the PM levels inside their residences. This study also provides biologically relevant results on the lung deposition of particles from residential biomass burning that can be used as a reference for future research. Presented on: Environmental Science and Pollution Research

Highlights • New high-resolution emission inventory for Nordic residential wood combustion. • Country level methods can produce similar spatial distributions as local level. • Difference between urban and rural RWC is important for the spatial distribution. • National characteristics are essential for spatial representation of RWC emissions. Residential wood combustion (RWC) is a major source of air pollutants in the Nordic and many other countries. The emissions of the pollutants have been estimated with inventories on several scopes, e.g. local and national. An important aspect of the inventories is the spatial distribution of the emissions, as it has an effect on health impact assessments. In this study, we present a novel residential wood combustion emission inventory for the Nordic countries based on national inventories and new gridding of the emissions. We compare the emissions of the Nordic inventory, and especially their spatial distribution, to local assessments and European level TNO-newRWC-inventory to assess the spatial proxies used. Common proxies used in the national inventories in the Nordic countries were building data on locations and primary heating methods and questionnaire-based wood use estimates for appliances or primary heating methods. Chimney sweeper register data was identified as good proxy data, but such data may not be available in an applicable format. Comparisons of national inventories to local assessments showed the possibility to achieve similar spatial distributions through nation-wide methods as local ones. However, this won't guarantee that the emissions are similar. Comparison to the TNO-newRWC-inventory revealed the importance of how differences between urban and rural residential wood combustion are handled. The comparison also highlighted the importance of local characteristics of residential wood combustion in the spatial distribution of emissions.

Residential wood combustion (RWC) is an important contributor to air quality in numerous regions worldwide. This study is the first extensive evaluation of the influence of RWC on ambient air quality in several Nordic cities. We have analysed the emissions and concentrations of PM classCombining double low line"inline-formula" 2.5 in cities within four Nordic countries: in the metropolitan areas of Copenhagen, Oslo, and Helsinki and in the city of Umeä. We have evaluated the emissions for the relevant urban source categories and modelled atmospheric dispersion on regional and urban scales. The emission inventories for RWC were based on local surveys, the amount of wood combusted, combustion technologies and other relevant factors. The accuracy of the predicted concentrations was evaluated based on urban concentration measurements. The predicted annual average concentrations ranged spatially from 4 to 7  classCombining double low line"inline-formula" μg m-3 (2011), from 6 to 10  classCombining double low line"inline-formula" μg m-3 (2013), from 4 to more than 13  classCombining double low line"inline-formula" μg m-3 (2013) and from 9 to more than 13  classCombining double low line"inline-formula" μg m-3 (2014), in Umeä, Helsinki, Oslo and Copenhagen, respectively. The higher concentrations in Copenhagen were mainly caused by the relatively high regionally and continentally transported background contributions. The annual average fractions of PM classCombining double low line"inline-formula" 2.5 concentrations attributed to RWC within the considered urban regions ranged spatially from 0 % to 15 %, from 0 % to 20 %, from 8 % to 22 % and from 0 % to 60 % in Helsinki, Copenhagen, Umeä and Oslo, respectively. In particular, the contributions of RWC in central Oslo were larger than 40 % as annual averages. In Oslo, wood combustion was used mainly for the heating of larger blocks of flats. In contrast, in Helsinki, RWC was solely used in smaller detached houses. In Copenhagen and Helsinki, the highest fractions occurred outside the city centre in the suburban areas. In Umeä, the highest fractions occurred both in the city centre and its surroundings.

Alkali-containing submicron particles were measured continuously during three months, including late winter and spring seasons in Gothenburg, Sweden. The overall aims were to characterize the ambient concentrations of combustion-related aerosol particles and to address the importance of local emissions and long-range transport for atmospheric concentrations in the urban background environment. K and Na concentrations in the particulate matter PM1 size range were measured by an Alkali aerosol mass spectrometer (Alkali-AMS) and a cluster analysis was conducted. Local meteorological conditions and trace gas and PM concentrations were also obtained for a nearby location. In addition, back trajectory analyses and chemical transport model (CTM) simulations were included for the evaluation. The Alkali-AMS cluster analysis indicated three major clusters: (1) biomass burning origin, (2) mixture of other combustion sources, and (3) marine origin. Low temperatures and low wind speed conditions correlated with high concentrations of K-containing particles, mainly owing to local and regional emissions from residential biomass combustion, transport of air masses from continental Europe also contribute to Cluster 1. The CTM results indicate that open biomass burning in the eastern parts of Europe may have contributed substantially to high PM2.5 concentrations (and to Cluster 1) during an episode in late March. According to the CTM results, the mixed cluster (2) is likely to include particles emitted from different source types and no single geographical source region seems to dominate for this cluster. The back trajectory analysis and meteorological conditions indicated that the marine origin cluster was correlated with westerly winds and high wind speed, this cluster had high concentrations of Na-containing particles, as expected for sea salt particles.

Particulate matter with aerodynamic diameter < 10 μm (PM10) was collected, indoors and outdoors, when wood burning appliances (open fireplace and woodstove) were in operation. The PM10 ecotoxicity was assessed with the Vibrio fischeri bioluminescence inhibition assay, while the cytotoxicity was evaluated by the WST-8 and lactate dehydrogenase (LDH) release assays using A549 cells. Extracts of PM10-bound polycyclic aromatic hydrocarbons (PAH) were tested for their mutagenicity through the TA98 and TA100 Ames test. The bioluminescent inhibition assay revealed that indoor particles released from the fireplace were the most toxic. Indoors, the reduction in A549 cell metabolic activity was over two times higher for the fireplace in comparison with the woodstove (32 ± 3.2% and 72 ± 7.6% at the highest dose, respectively). Indoor particles from the fireplace were found to induce greater cytotoxicity than the corresponding outdoor samples. Combined WST-8 and LDH results suggest that PM10 exposure induce apoptotic cell death pathway in which the cell membrane integrity is maintained. Indoor and outdoor samples lacked direct and indirect mutagenic activity in any of the tester strains. For indoor-generated PM10, organic carbon and PAH were significantly correlated with cell viability and bioluminescence reduction, suggesting a role of organic compounds in toxicity. published

The San Joaquin Valley in California suffers from poor air quality due to a combination of local emissions and weak ventilation. Over the course of decades, there has been a concerted effort to control emissions from vehicles as well as from residential wood burning. A multiple linear regression model was used to evaluate the trends in air pollution over multiple time scales: by year, by season, by day of the week and by time of day. The model was applied to 18 years of measurements in Fresno including hourly mole fractions of NOx and concentrations of PM2.5; and daily measurements of speciated components of PM2.5. The analysis shows that there have been reductions in NOx, elemental carbon and ammonium nitrate of 4 to 6%/year. On weekends, NOx mole fractions are reduced by 15 to 30% due to fewer vehicle miles traveled and a smaller fraction of diesel traffic. These weekend reductions in NOx have not been accompanied by weekend reductions in PM2.5 however. In particular, elemental and organic carbon concentrations are higher on winter weekends. Analysis of diurnal profiles suggests that this is because of increased PM2.5 on Saturday and holiday evenings which are likely due to residential wood combustion. Furthermore, while organic carbon concentrations have decreased in the winter months, they have been variable but without a net decline in the summer, most likely as a result of forest fires offsetting other improvements in air quality. Fog was found to greatly enhance ammonium nitrate formation and was therefore associated with higher PM2.5 in the winter months. Overall the analysis shows that air quality controls have been effective at reducing NOx all year and PM2.5 in the winter, that continued reductions in emissions will further reduce pollutant concentrations, but that winter residential wood combustion and summer forest fires could offset some of the gains obtained.

Exposure to fine particles in ambient air has been estimated to be one of the leading environmental health risks in Finland. Residential wood combustion is the largest domestic source of fine particles, and there is increasing political interest in finding feasible measures to reduce those emissions. In this paper, we present the PM2.5 emissions from residential wood combustion in Finland, as well as the resulting concentrations. We used population-weighed concentrations in a 250 x 250 m grid as population exposure estimates, with which we calculated the disease burden of the emissions. Compared to a projected baseline scenario, we studied the effect of chosen reduction measures in several abatement scenarios. In 2015, the resulting annual average concentrations were between 0.5 and 2 &micro, g/m3 in the proximity of most cities, and disease burden attributable to residential wood combustion was estimated to be 3400 disability-adjusted life years (DALY) and 200 deaths. Disease burden decreased by 8% in the 2030 baseline scenario and by an additional 63% in the maximum feasible reduction scenario. Informational campaigns and improvement of the sauna stove stock were assessed to be the most feasible abatement measures to be implemented in national air quality policies.

Exposure to fine particles in ambient air has been estimated to be one of the leading environmental health risks in Finland. Residential wood combustion is the largest domestic source of fine particles, and there is increasing political interest in finding feasible measures to reduce those emissions. In this paper, we present the PM2.5 emissions from residential wood combustion in Finland, as well as the resulting concentrations. We used population-weighed concentrations in a 250 × 250 m grid as population exposure estimates, with which we calculated the disease burden of the emissions. Compared to a projected baseline scenario, we studied the effect of chosen reduction measures in several abatement scenarios. In 2015, the resulting annual average concentrations were between 0.5 and 2 µg/m3 in the proximity of most cities, and disease burden attributable to residential wood combustion was estimated to be 3400 disability-adjusted life years (DALY) and 200 deaths. Disease burden decreased by 8% in the 2030 baseline scenario and by an additional 63% in the maximum feasible reduction scenario. Informational campaigns and improvement of the sauna stove stock were assessed to be the most feasible abatement measures to be implemented in national air quality policies.

Carbonaceous aerosol (total carbon, TCp) was source apportioned at nine European rural background sites, as part of the European Measurement and Evaluation Programme (EMEP) Intensive Measurement Periods in fall 2008 and winter/spring 2009. Five predefined fractions were apportioned based on ambient measurements: elemental and organic carbon, from combustion of biomass (ECbb and OCbb) and from fossil-fuel (ECff and OCff) sources, and remaining non-fossil organic carbon (OCrnf), dominated by natural sources. OCrnf made a larger contribution to TCp than anthropogenic sources (ECbb, OCbb, ECff, and OCff) at four out of nine sites in fall, reflecting the vegetative season, whereas anthropogenic sources dominated at all but one site in winter/spring. Biomass burning (OCbb + ECbb) was the major anthropogenic source at the central European sites in fall, whereas fossil-fuel (OCff + ECff) sources dominated at the southernmost and the two northernmost sites. Residential wood burning emissions explained 30 %–50 % of TCp at most sites in the first week of sampling in fall, showing that this source can be the dominant one, even outside the heating season. In winter/spring, biomass burning was the major anthropogenic source at all but two sites, reflecting increased residential wood burning emissions in the heating season. Fossil-fuel sources dominated EC at all sites in fall, whereas there was a shift towards biomass burning for the southernmost sites in winter/spring. Model calculations based on base-case emissions (mainly officially reported national emissions) strongly underpredicted observational derived levels of OCbb and ECbb outside Scandinavia. Emissions based on a consistent bottom-up inventory for residential wood burning (and including intermediate volatility compounds, IVOCs) improved model results compared to the base-case emissions, but modeled levels were still substantially underestimated compared to observational derived OCbb and ECbb levels at the southernmost sites. Our study shows that natural sources are a major contributor to carbonaceous aerosol in Europe, even in fall and in winter/spring, and that residential wood burning emissions are equally as large as or larger than that of fossil-fuel sources, depending on season and region. The poorly constrained residential wood burning emissions for large parts of Europe show the obvious need to improve emission inventories, with harmonization of emission factors between countries likely being the most important step to improve model calculations for biomass burning emissions, and European PM2.5 concentrations in general.

In recent years, residential wood combustion (RWC) has become a major source of ambient particulate matter (PM) in many developed countries, and in some of these countries even the largest source of primary particle emissions. While other sources of PM have been regulated intensively during the past decades, RWC has been subject to only minor regulation despite of its impact on climate and health. This review covers recent research publications on RWC contributions to ambient PM in different regions of Europe, North America and Australasia, and on key species associated with RWC. Furthermore, factors governing emissions from wood stoves (as the typical appliance used in residential heating) are evaluated. State-of-the-art methods for estimating RWC as a source of ambient PM are discussed. We conclude by highlighting important areas for future research and policies.

Residential wood combustion (RWC) is a major source of climate-impacting emissions, like short-lived climate forcers (SLCF) and biogenic CO2, in Finland. In this paper, we present projections for those emissions from 2015 to 2040. We calculated the climate impact of the emissions using regional temperature potential metrics presented in literature. In our results, the climate impacts are given as global and Arctic temperature responses caused by the studied emissions in a 25 year time span. The results show that SLCF emissions from RWC cause a significant warming impact. Using our selected metrics, SLCF emissions from RWC added to the warming impact of Finland's projected greenhouse gas emissions by 28% in global temperature response and by 170% in Arctic response. When compared with other common heating methods in Finnish detached houses, using a typical Finnish stove (masonry heater) was the least climate-friendly option. Taking biogenic CO2 emissions into account further highlighted this finding. Finally, we assessed the change in climate impact when implementing various emission reduction measures for RWC. With a time span of 25 years, early action was found to be even more crucial than the eventual reductions in annual emissions in 2040. Highlights • RWC is the major source of BC and many other SLCFs in Finland. • SLCF emissions from Finnish RWC have a relatively significant climate impact, compared with GHGs. • Using a stove was found to be the least climate-friendly option to heat a house. • Biogenic CO2 emissions need to be included in assessments. • Early action is key in SLCF emission reduction measures.

Residential wood combustion (RWC) is a major contributor to atmospheric pollution especially for particulate matter. Air pollution has significant impact on human health, and it is therefore important to know the human exposure. For this purpose, it is necessary with a detailed high resolution spatial distribution of emissions. In previous studies as well as in the model previously used in Denmark, the spatial resolution is limited, e.g. municipality or county level. Further, in many cases models are mainly relying on population density data as the spatial proxy for distributing the emissions. This paper describes the new Danish model for high resolution spatial distribution of emissions from RWC to air. The new spatial emission model is based on information regarding building type, and primary and supplementary heating installations from the Danish Building and Dwelling Register (BBR), which holds detailed data for all buildings in Denmark. The new model provides a much more accurate distribution of emissions than the previous model used in Denmark, as the resolution has been increased from municipality level to a 1 km × 1 km resolution, and the distribution key has been significantly improved so that it no longer puts an excessive weight on population density. The new model has been verified for the city of Copenhagen, where emissions estimated using both the previous and the new model have been compared to the emissions estimated in a case study. This comparison shows that the new model with the developed weighting factors (76 ton PM2.5) is in good agreement with the case study (95 ton PM2.5), and that the new model has improved the spatial emission distribution significantly compared to the previous model (284 ton PM2.5). Additionally, a sensitivity analysis was done to illustrate the impact of the weighting factors on the result, showing that the new model independently of the weighting factors chosen produce a more accurate result than the old model.

Sauna Stoves (SS) are simple wood combustion appliances used mainly in Nordic countries. They generate emissions that have an impact on air quality and climate. In this study, a new measurement concept for comparing the operation, thermal efficiency, and real-life fine particle and gaseous emissions of SS was utilized. In addition, a novel, simple, and universal emission calculation procedure for the determination of nominal emission factors was developed for which the equations are presented for the first time. Fine particle and gaseous concentrations from 10 different types of SS were investigated. It was found that each SS model was an individual in relation to stove performance: stove heating time, air-to-fuel ratio, thermal efficiency, and emissions. Nine-fold differences in fine particle mass (PM1) concentrations, and about 90-fold differences in concentrations of polycyclic aromatic hydrocarbons (PAH) were found between the SS, when dry (11% moisture content) birch wood was used. By using moist (18%) wood, particle number and carbon monoxide concentrations increased, but interestingly, PM1, PAH, and black carbon (BC) concentrations clearly decreased, when comparing to dry wood. E.g., PAH concentrations were 5.5&ndash, 9.6 times higher with dry wood than with moist wood. Between wood species, 2&ndash, 3-fold maximum differences in the emissions were found, whereas about 1.5-fold differences were observed between bark-containing and debarked wood logs. On average, the emissions measured in this study were considerably lower than in previous studies and emission inventories. This suggests that overall the designs of sauna stoves available on the market have improved during the 2010s. The findings of this study were used to update the calculation scheme behind the inventories, causing the estimates for total PM emissions from SS in Finland to decrease. However, wood-fired sauna stoves are still estimated to be the highest individual emission source of fine particles and black carbon in Finland.

Sources of elemental carbon (EC) and organic carbon (OC) in atmospheric aerosols (carbonaceous aerosols) were investigated by collection of weekly aerosol filter samples at six background sites in Northern Europe (Birkenes, Norway; Vavihill, Sweden; Risoe, Denmark; Cabauw and Rotterdam in The Netherlands; Melpitz, Germany) during winter 2013. Analysis of 14C and a set of molecular tracers were used to constrain the sources of EC and OC. During the four-week campaign, most sites (in particular those in Germany and The Netherlands) were affected by an episode during the first two weeks with high concentrations of aerosol, as continental air masses were transported westward. The analysis results showed a clear, increasing north to south gradient for most molecular tracers. Total carbon (TC = OC + EC) at Birkenes showed an average concentration of 0.5 ± 0.3 μg C m−3, whereas the average concentration at Melpitz was 6.0 ± 4.3 μg C m−3. One weekly mean TC concentration as high as 11 μg C m−3 was observed at Melpitz. Average levoglucosan concentrations varied by an order of magnitude from 25 ± 13 ng m−3 (Birkenes) to 249 ± 13 ng m−3 (Melpitz), while concentrations of tracers of fungal spores (arabitol and mannitol) and vegetative debris (cellulose) were very low, showing a minor influence of primary biological aerosol particles during the North European winter. The fraction of modern carbon generally varied from 0.57 (Melpitz) to 0.91 (Birkenes), showing an opposite trend compared to the molecular tracers and TC. Total concentrations of 10 biogenic and anthropogenic carboxylic acids, mainly of secondary origin, were 4–53 ng m−3, with the lowest concentrations observed at Birkenes and the highest at Melpitz. However, the highest relative concentrations of carboxylic acids (normalized to TC) were observed at the most northern sites. Levels of organosulphates and nitrooxy organosulphates varied more than two orders of magnitude, from 2 to 414 ng m−3, between individual sites and samples. The three sites Melpitz, Rotterdam and Cabauw, located closest to source regions in continental Europe, showed very high levels of organosulphates and nitrooxy organosulphates (up to 414 ng m−3) during the first two weeks of the study, while low levels (40% of TC), while use and combustion of fossil fuels was the second most important source. Furthermore, EC from biomass burning accounted for 7–16% of TC, whereas EC from fossil sources contributed to

Logs of three common Southern and mid-European woods (Quercus pyrenaica, Populus nigra and Fagus sylvatica) were burned in two different combustion appliances, a fireplace and a stove. The flue gas composition was monitored continuously in the exhaust ducts of both burning appliances for total hydrocarbons (THC) and carbon oxides (CO2 and CO). Particulate matter with aerodynamic diameter below 2.5 μm (PM2.5) was sampled in a dilution tunnel under isokinetic conditions and chemically characterised for water soluble-inorganic ions, organic and elemental carbon and levoglucosan, mannosan, and galactosan. The evolution of the emission factors of these components throughout the combustion cycle was studied. The fireplace was the combustion appliance with the highest CO, CO2, THC and PM2.5 emission factors. The carbonaceous matter represented 72–84% of the particulate mass emitted, regardless of species burned and combustion devices. OC/EC ratios were higher for the fireplace than for the stove, and showed a significant potential relation with K+/levoglucosan. The dominant water soluble inorganic ions in smoke particles were K+, PO 4 3 − , SO 4 2 − , and Na+. Anhydrosugar emissions were strongly enhanced in the start-up phase, when lower temperatures are registered, and decreased progressively until the glowing combustion phase. However, K+ emission seems to be higher in flaming-dominated combustion at higher temperature. Statistical analyses, including the Kruskal–Wallis test, principal component analysis and Pearson correlation between emission factors, were carried out. A significant correlation between NH4+ and levoglucosan was found for both appliances.

The most important anthropogenic sources of primary particulate matter (PM) in ambient air in Europe are exhaust and non-exhaust emissions from road traffic and combustion of solid biomass. There is convincing evidence that PM, almost regardless of source, has detrimental health effects. An important issue in health impact assessments is what metric, indicator and exposure-response function to use for different types of PM. The aim of this study is to describe sectorial contributions to PM exposure and related premature mortality for three Swedish cities: Gothenburg, Stockholm and Umea. Exposure is calculated with high spatial resolution using atmospheric dispersion models. Attributed premature mortality is calculated separately for the main local sources and the contribution from long-range transport (LRT), applying different relative risks. In general, the main part of the exposure is due to LRT, while for black carbon, the local sources are equally or more important. The major part of the premature deaths is in our assessment related to local emissions, with road traffic and residential wood combustion having the largest impact. This emphasizes the importance to resolve within-city concentration gradients when assessing exposure. It also implies that control actions on local PM emissions have a strong potential in abatement strategies.

The most important anthropogenic sources of primary particulate matter (PM) in ambient air in Europe are exhaust and non-exhaust emissions from road traffic and combustion of solid biomass. There is convincing evidence that PM, almost regardless of source, has detrimental health effects. An important issue in health impact assessments is what metric, indicator and exposure-response function to use for different types of PM. The aim of this study is to describe sectorial contributions to PM exposure and related premature mortality for three Swedish cities: Gothenburg, Stockholm and Umea. Exposure is calculated with high spatial resolution using atmospheric dispersion models. Attributed premature mortality is calculated separately for the main local sources and the contribution from long-range transport (LRT), applying different relative risks. In general, the main part of the exposure is due to LRT, while for black carbon, the local sources are equally or more important. The major part of the premature deaths is in our assessment related to local emissions, with road traffic and residential wood combustion having the largest impact. This emphasizes the importance to resolve within-city concentration gradients when assessing exposure. It also implies that control actions on local PM emissions have a strong potential in abatement strategies.

Air pollution cause approximately 5000 premature deaths in Sweden each year. Residential wood combustion of solid biomass (RWC) is responsible for at least 1000 based on a relative risk coefficient of 17 % per 10 μg/m3 exposure. The carcinogenic properties of RWC emissions is linked to their content of particulates and polycyclic aromatic hydrocarbons (PAH’s). The ambition of this study is to answer whether cancer risk may be used as indicator for out dated heating technology with high emissions of carcinogenic air pollutants, and which socioeconomic costs that can be linked to such a scenario. The efficacy of different instruments that are discussed in Swedish environmental policy is also discussed. A transdisciplinary approach, constituting of a literature review, statistical analysis, gap analysis and multi criteria analysis was applied as study design. A literature review resulted in a mapping of the state of the art concerning RWC particulates and their impact on cancer in Sweden together with its related socioeconomic costs. The study is focused on PM2,5 and B(a)P emissions. A statistical analysis examined the potential relationship between short-lived micro nuclei (MN) in Swedish 12-year old school children, and their exposure to the carcinogenic PAH Benzo(a)pyrene (B(a)P) from RWC in Sweden. The results suggest that higher rates of lung cancer incidence, and socioeconomic costs may be found in areas burdened with high rates of RWC emissions from outdated heating technology. The MCA suggest that a combination of instruments is most suitable to achieve the targeted specification for B(a)P in the Clean Air objective, as found in previous CBA’s, and that other instrument may lack efficacy. Varje år orsakar luftföroreningar omkring 5000 prematura dödsfall i Sverige. Småskalig vedeldning (RWC) ansvarar för åtminstone 1000 av dessa, baserat på den relativa risk-koefficienten 17 % per 10 μg/m3 exponering. De cancerogena egenskaperna hos vedeldningsutsläpp beror bland annat på dess partiklar som bland annat innehåller polycykliska aromatiska kolväten (PAH:er). Ambitionen med denna studie är att besvara hur framtida cancerrisk kan användas som indikator för luftföroreningar från omodern uppvärmningsteknik och vilka samhällsekonomiska följder som kan länkas till en sådan. Dessutom undersöktes styrkraften hos de styrmedel som diskuteras i svensk miljöpolicy. Med hjälp av ett tvärvetenskapligt tillvägagångssätt, bestående av litteraturgenomgång, statistisk analys, gapanalys och multikriterieanalys besvarades frågorna. Litteraturgenomgången resulterade i en kartläggning av det nuvarande kunskapsläget om vedpartiklars påverkan på cancer i Sverige och dess relaterade samhällskostnader. Studien är fokuserad på PM2,5 och B(a)P emissioner. En statistisk analys undersökte korrelationen mellan en biomarkor för framtida cancerrisk, kortlivade mikrokärnor (MN), hos svenska 12-åriga skolelever, och deras vedröksexponering. Resultaten indikerar svagt att större risk för lungcancer kan spås i områden med relativt högre exponering för vedrökskomponenten B(a)P, alltså områden med omodern uppvärmningsutrustning. Multikriterieanalysen visar, liksom i tidigare kostnad-effektivitetsanalyser, att en kombination av olika styrmedel har störst potential att uppnå specifikationerna för PM2,5 och B(a)P i det svenska miljökvalitetsmålet Ren luft. Andra styrmedel kan sakna styrkraft.

In this study, the emissions of three different generations of firewood stoves were characterized to test their sustainability with this new problematic. Organic Carbon (OC) and Elemental Carbon (EC) emissions were particularly targeted. After an investigation of the OC/EC measurement method, a specific protocol was developed, validated and optimized in order to measure OC/EC from direct samplings in the flue gas, without diluting or cooling systems. Carbon monoxide (CO), Total Suspended Particles (TSP) and Total Hydrocarbon (THC) emissions were followed too. To go further in the characterization and in the differentiation of the particles emitted from each kind of stoves, a Field Emission Gun Scanning Electron Microscope (FEG SEM) was used. The medium generation emitted 40% less mass of OC than the previous one. Concerning the new generation, emissions were reduced in mass about 98% for the EC and 40% for the OC compared to the old generation.

Four manually fed (6–11 kW) firewood burning and two automatic wood pellets (8.8–25 kW) residential heating appliances were tested under real-world operating conditions in order to determine emission factors (EFs) of macropollutants, i.e., carbon monoxide (CO), nitrogen oxides (NO x ), non-methane hydrocarbons (NMHC), particulate matter (PM) and trace pollutants such as polycyclic aromatic hydrocarbons (PAH) and dioxins. The results were examined for the influence of different factors (i.e., type of wood, appliance and combustion cycle). The experimental EFs were also compared with the values proposed by the European emission inventory guidebook used in the local inventory in order to evaluate their representativeness of real world emissions. The composite macropollutant EFs for manually fed appliances were: for CO 5858 g GJ −1 , for NO x 122 g GJ −1 , NMHC 542 g GJ −1 , PM 254 g GJ −1 , whereas emissions were much lower for automatic pellets appliances: CO 219 g GJ −1 , for NO x 66 g GJ −1 , NMHC 5 g GJ −1 , PM 85 g GJ −1 . The highest emissions were generally observed for the open fireplace, however traditional and advanced stoves have the highest overall CO EFs. Especially for the advanced stove real-world emissions are far worse than those measured under cycles used for type testing of residential solid fuel appliances. No great difference is observed for different firewood types in batch working appliances, diversely the quality of the pellets is observed to influence directly the emission performance of the automatic appliances. Benzo(b)fluoranthene is the PAH with the highest contribution (110 mg GJ −1 for manual appliances and 2 mg GJ −1 for automatic devices) followed by benzo(a)pyrene (77 mg GJ −1 for manual appliances and 0.8 mg GJ −1 for automatic devices).

Solid fuel emissions, including those from biomass burning, are increasing in urban areas across the European Union due to rising energy costs and government incentives to use renewable energy sources for heating. In order to help protect human health as well as to improve air quality and pollution abatement strategies, the sources of combustion aerosols, their contributions, and the processes they undergo need to be better understood. A high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) was therefore deployed at an urban background site between January and February 2012 to investigate solid fuel organic aerosols (SFOA) in London. The variability of SFOA was examined and the factors governing the split between the two SFOA factors derived from Positive Matrix Factorisation (PMF) were assessed. The concentrations of both factors were found to increase during the night and during cold periods, consistent with domestic space heating activities. The split between the two factors is likely governed predominantly by differences in burn conditions where SFOA1 best represents more efficient burns and SFOA2 best represents less efficient burns. The differences in efficiency may be due to burner types or burn phase, for example. Different fuel types and levels of atmospheric processing also likely contribute to the two factors. As the mass spectral profile of SFOA is highly variable, the findings from this study may have implications for improving future source apportionment and factorisation analyses. During the winter, SFOA was found to contribute 38% to the total non-refractory submicron organic aerosol (OA) mass, with similar contributions from both SFOA factors (20% from SFOA1 and 18% from SFOA2). A similar contribution of SFOA was derived for the same period from a compact time-of-flight AMS (cToF-AMS), which measured for a full calendar year at the same site. The seasonality of SFOA was investigated using the year-long data set where concentrations were greatest in the autumn and winter. During the summer, SFOA contributed 11% to the organic fraction, where emissions resulted from different anthropogenic activities such as barbecues and domestic garden wood burning. The significant contribution of SFOA to total organic mass throughout the year suggests that the negative effects on health and air quality, as well as climate, are not just confined to winter as exposure to these aerosols and the associated black carbon can also occur during the summer, which may have significant implications for air-quality policies and mitigation strategies.

We use a 3-D regional chemical transport model, with the latest advancements in the organic aerosol (OA) treatment, and an updated emission inventory for wood combustion to study the organic aerosol change in response to the replacement of current residential wood combustion technologies with pellet stoves. Simulations show a large decrease of fine organic aerosol (more than 60%) in urban and suburban areas during winter and decreases of 30-50% in elemental carbon levels in large parts of Europe. There is also a considerable decrease (around 40%) of oxidized OA, mostly in rural and remote regions. Total PM2.5 mass is predicted to decrease by 15-40% on average during the winter in continental Europe. Accurate representation of the intermediate volatility precursors of organic aerosol in the emission inventory is crucial in assessing the efficiency of such abatement strategies. © 2014 Elsevier Ltd. Chemicals/CAS: carbon, 7440-44-0

We use a 3-D regional chemical transport model, with the latest advancements in the organic aerosol (OA) treatment, and an updated emission inventory for wood combustion to study the organic aerosol change in response to the replacement of current residential wood combustion technologies with pellet stoves. Simulations show a large decrease of fine organic aerosol (more than 60%) in urban and suburban areas during winter and decreases of 30-50% in elemental carbon levels in large parts of Europe. There is also a considerable decrease (around 40%) of oxidized OA, mostly in rural and remote regions. Total PM2.5 mass is predicted to decrease by 15-40% on average during the winter in continental Europe. Accurate representation of the intermediate volatility precursors of organic aerosol in the emission inventory is crucial in assessing the efficiency of such abatement strategies. © 2014 Elsevier Ltd. Chemicals/CAS: carbon, 7440-44-0

There is a need to decrease the detrimental particle and gaseous emissions from residential wood combustion appliances. One encouraging alternative is to stage the air supply which improves the combustion conditions in small appliances. In this study, two types of combustion technologies were studied in conventional masonry heaters (CMH) and modern masonry heaters (MMH). Air staging in the MMHs considerably reduced the particle and gas emissions. The greatest reduction was observed in gaseous and particulate organic emissions. Methane emissions were reduced by 74%–91% and carbon monoxide by 26%–81%. The reduction of fine particle mass (PM 1 ) was 14%–58%. Elemental carbon (EC, i.e. soot) emission increased in small combustion appliances but declined in large appliances. In addition, dust (TSP, Total Suspended Particulate matter i.e. Dust) emissions from hot flue gas were compared with the fine particle mass emissions from diluted sample. PM 1 emissions measured from diluted flue gas were 1.1–4.4-fold as compared to TSP collected from hot flue gas. This may be attributable to the fact that organic vapors partially had penetrated into the TSP filter in a gaseous form whereas when they were diluted, semivolatile species condensed on the particles. It can be concluded that air staging is an effective way to reduce gaseous and organic emissions from batch combustion appliances. Particle emission measured from diluted flue gas represents a more realistic results than TSP (hot sampling), because in dilution, also the organic fraction of the particle emissions is taken into account.

This project (KoL 12-08) was performed for the Climate and Air Quality Group (KlimaogLuftgruppen, KoL), Nordic Council of Ministers by atmospheric emission, exposureand epidemiology experts from Denmark, Finland, Norway and Sweden. Emission inventory methods and exposure models were presented. A list of carcinogenic andco-carcinogenic pollutants (particles, heavy metals and organic compounds) emittedfrom energy production, industrial activities, road transport, navigation, agriculture, residential heating and product use was compiled. Pollutant emissions levels for 2010and trends for 1990 to 2010 were compiled and discussed, and modelled andmeasured atmospheric concentrations for 2010 were compiled on regional, urbanand local scales. Nordic maps of emissions and air concentrations of PM2.5, PM10, NOx,NMVOC, benzene, BaP, dioxin, cadmium and nickel were compiled for allaggregated main sources, traffic and residential wood combustion. An overview of local studies on exposure for cities or communities with emphasis on wood combustion and traffic and a discussion of existing epidemiological studies on cancer and environment were given

The contribution of residential wood combustion (RWC) to emission inventory at local level was estimated using a bottom–up approach for the Lombardy Region of North Italy. A survey, based on the CATI (Computer Assisted Telephone Interviewing) method, has been undertaken through 18,000 interviews. The interviews had the objective to characterize the RWC use in this region, in term of both total and municipal wood consumption. Details on the type of appliances used in RWC were also gathered. The results of the survey were then statistically analyzed in order to allow an estimate of RWC with high spatial resolution (i.e., at municipal level) in relation to the size and altitude of the territory. The work provides new evidence of the importance of wood combustion as a key source for PM and NMVOC emissions at local level, and thus highlights the importance of technological improvements and new policies aimed at emission reduction in this sector. Considering the great differences in average PM emission factors between low efficiency appliances (fireplaces, old stoves) and high efficiency ones (new stoves, pellet burners), this work emphasizes the importance of obtaining more detailed information on the types of wood appliances used for arriving at a reliable PM emission inventory for RWC.

Residential heating is an important local source of fine particles and may cause significant exposure and health effects in populations. We investigated the cytotoxic and inflammatory activity of particulate emissions from normal (NC) and smouldering (SC) combustion in one masonry heater. The PM1–0.2 and PM0.2 samples were collected from the dilution tunnel with a high-volume cascade impactor (HVCI). Mouse RAW 264.7 macrophages were exposed to the PM-samples for 24 h. Inflammatory mediators, (IL-6, TNFα and MIP-2), and cytotoxicity (MTT-test), were measured. Furthermore, apoptosis and cell cycle of macrophages were analyzed. The HVCI particulate samples were characterized for ions, elements and PAH compounds. Assays of elemental and organic carbon were conducted from parallel low volume samples. All the samples displayed mostly dose-dependent inflammatory and cytotoxic activity. SC samples were more potent than NC samples at inducing cytotoxicity and MIP-2 production, while the order of potency was reversed in TNFα production. SC-PM1–0.2 sample was a significantly more potent inducer of apoptosis than the respective NC sample. After adjustment for the relative toxicity with emission factor (mg MJ−1), the SC-PM emissions had clearly higher inflammatory and cytotoxic potential than the NC-PM emissions. Thus, operational practice in batch burning of wood and the resultant combustion condition clearly affect the toxic potential of particulate emissions.

Wood combustion is mainly used in cold regions as a primary or supplemental space heating source in residential areas. In several industrialized countries, there is a renewed interest in residential wood combustion (RWC) as an alternative to fossil fuel and nuclear power consumption. The main objective of this thesis was to investigate the impact of RWC on the air quality in urban areas. To this end, a field campaign was conducted in Northern Sweden during wintertime to characterize atmospheric aerosol particles and polycyclic aromatic hydrocarbons (PAH) and to determine their source apportionment. A large day-to-day and hour-to-hour variability in aerosol concentrations was observed during the intensive field campaign. On average, total carbon contributed a substantial fraction of PM10 mass concentrations (46%) and aerosol particles were mostly in the fine fraction (PM1 accounted for 76% of PM10). Evening aerosol concentrations were significantly higher on weekends than on weekdays which could be associated to the use of wood burning for recreational purposes or higher space heat demand when inhabitants spend longer time at home. It has been shown that continuous aerosol particle number size distribution measurements successfully provided source apportionment of atmospheric aerosol with high temporal resolution. The first compound-specific radiocarbon analysis (CSRA) of atmospheric PAH demonstrated its potential to provide quantitative information on the RWC contribution to individual PAH. RWC accounted for a large fraction of particle number concentrations in the size range 25-606 nm (44-57%), PM10 (36-82%), PM1 (31-83%), light-absorbing carbon (40-76%) and individual PAH (71-87%) mass concentrations. These studies have demonstrated that the impact of RWC on air quality in an urban location can be very important and largely exceed the contribution of vehicle emissions during winter, particularly under very stable atmospheric conditions.

As part of the integrated research project (WOODUSE), NERI is