Search

Degradation of insulation paper is a key contributor to the failure of power transformers. Insulation degradation accelerates at elevated temperatures, which highlights the potential for better thermal management to prolong life. While several studies have analyzed the benefits of high thermal conductivity oil for reducing temperatures inside a transformer, this study is an initial assessment of the benefits of high thermal conductivity paper on transformer life. Blending particulates with cellulosic fibers offers a pathway for high thermal conductivity paper (with good dielectric properties), which can reduce internal temperatures. Presently, life extensions that can be achieved by the use of such thermally conducting papers were estimated, with the thermal conductivity of the paper being the key parameter under study. The analytical-numerical thermal model used in this study was validated against experimental measurements in a distribution transformer, adding confidence to the utility of the model. This model was then used to provide estimates of hot-spot temperature reduction resulting from the use of papers with higher thermal conductivity than baseline. Transformer life was predicted conventionally by tracking the degree of polymerization of paper over time, based on an Arrhenius model. Results indicate that increasing the thermal conductivity of paper from 0.2 W/mK (baseline) to 1 W/mK reduces the hot spot temperature by 10 °C. While degradation significantly depends on the moisture and oxygen content, the model shows that such a temperature reduction can increase life for all conditions, by as much as a factor of three.

Abstract This study identifies important factors for designing an effective biomimetic paper‐based fog harvesting substrate by examining the harvesting properties of different surfaces, including glass, polyethylene, and superhydrophobic paper. In laboratory‐scale fogging tests, the wetting behavior of the substrates is characterized, and the importance of the tilt angle of the respective surface relative to the fog flow is elaborated. Because successful fog harvesting requires both efficient accumulation of water droplets on the surface (by condensation and collision) and sufficient but not excessive roll‐off of the liquid, the amount of water finally collected is clearly related to the pinning effect, which should prevent the smallest droplets from being carried away by the wind but must not lead to full and permanent wetting of the surface. Coalescence is identified as a major phenomenon to improve droplet roll‐off. In this context, superhydrophobic paper indicates to be a more effective water collector than glass or polyethylene, especially when oriented vertically, since it allows the droplets to roll off very efficiently. Finally, the addition of glass particles to the superhydrophobic coating is proposed as a means of enhancing pinning and improving the fog harvesting efficiency.

BackgroundIn recent years, the rising number of e-cigarette users among adolescents and the surging cases of lung injury related to e-cigarette use have attracted the attention of researchers in various fields.ObjectiveTo identify the research hotspots and trends of e-cigarette or vaping product use associated lung injury (EVALI) worldwide from 2013 to 2022 by bibliometric and visual analysis. MethodsWeb of Science Core Collection was selected to obtain literature related to EVALI from 2013 to 2022 across the world, statistics were calculated by country/region, institution, author, journal, cited literature, keyword, etc. CiteSpace 6.2.R1 was used for visual analysis to draw diagrams of publication trend, author cooperation network, co-citation clustering time distribution, and keyword cluster. ResultsA total of 888 EVALI-related papers published between 2013 and 2022 were retrieved. The number of publications was gradually increased, with a significant increase in 2020 and a decrease from 2021, but the number of citations was increased year by year. The most active country was the United States (631 articles). European and American countries cooperated closely and the centrality was prominent. Among the publishing institutions, the University of California system topped the list with 103 articles. Rahman I (27 articles) published the most articles and had a high degree of centrality; Goniewicz M L was the most cited author; and the network analysis diagram showed relatively weak collaboration between authors. The American Journal of Respiratory and Critical Care Medicine was the journal with the highest number of publications (94 articles). The top 5 cited articles were all cited more than 300 times. The leading high-frequency keywords of EVALI-related studies were nicotine (149 times), exposure (118 times), and oxidative stress (80 times). The cluster of key nodes in the co-citation network and the clustering time distribution diagram indicated youth e-cigarette addiction received widespread attention from society. From the top 25 keywords with the strongest bursts, the focus of research on the pathogenesis of EVALI gradually shifted from the oxidative stress damage associated with e-cigarette vapor to the oxidative effect of flavoring chemicals in the process of lung injury. The current research interests in this field were mainly the mechanisms of various chemicals in e-cigarettes and the heating elements that led to damage to the lungs. ConclusionEVALI is receiving continuous attention from researchers in government, medical institutions, and other organizations. A variety of e-cigarette ingredients such as flavoring chemicals may lead to varying degrees of cytotoxicity, inflammation, and lung damage. However, the pathophysiology of EVALI remains unclear. In the future, more Chinese scholars should be encouraged to participate in this field.

This study aimed to test the utility of ammonium persulfate (APS) oxidised nanofibrillated cellulose (NFC) as an additive for chitosan- and alginate-based biopolymer films that could eventually be used as paper coatings for food packaging applications. Sodium alginate and chitosan were used as the base for the films. Various concentrations of APS oxidised NFC ranging from 0% to 10% were used as a reinforcing agent, resulting in six combinations of either alginate-NFC or chitosan-NFC composite films. Biofilms were tested for their mechanical properties (tensile strength and strain), grease barrier properties, air permeability, water vapour permeability, and degradation in the soil. Overall, when using the ammonium persulfate oxidation pretreatment method, the best performance of the films was estimated with the addition of 2.5% NFC.

In this paper, the thermo-electric, phonon, electronic, and optical properties of the C3N monolayer have been investigated using the Wien2K computational code based on first principles calculations in the framework of the density functional theory. The study of electronic properties shows the behavior of non-magnetic semiconductors with an indirect gap with a value of 0.5 electron volts for this two-dimensional structure. Also, optical properties such as dielectric function, reflection, energy loss function, absorption coefficient, and optical conductivity are calculated. C3N monolayer is optically anisotropic in z and x direction, which according to the refractive index diagram leads to birefringence, which is a key parameter for this compound's linear optical performance. The results provide a fundamental understanding of the design of composite structures used in nanodevices based on two-dimensional advanced materials. The linear response approach along the symmetric points calculates the phonon dispersion diagram. The results indicate the absence of negative modes in the phonon spectrum, indicating that the structure is dynamically stable. Investigating the thermoelectric properties of the C3N monolayer using the semi-classical Boltzmann theory shows that this monolayer has a value coefficient (ZT) close to one at room temperature and temperatures lower than room temperature. As a result, it can be proposed as a candidate for thermoelectric applications.

Many non-classicality indicators are used to measure the quantum effects of different systems. Kenfack's and Sadeghi's non-classicality indicators are introduced regarding the amount of Wigner distribution function's negativities and interferences in phase space quantum mechanics, respectively. Kenfack’s non-classicality indicator is used for cases just in the Wigner representation, whereas Sadeghi’s non-classicality indicator is effectively, applied for some real distribution functions. In this paper, we investigate these non-classicality indicators for the entangled photon number states in the Wigner, Husimi, and Rivier representations. It is shown that for a two-level entangled state, Sadeghi's indicator has more benefits to measure entanglement with respect to Kenfack's indicator. For the two-level entangled state, we also show a correspondence between Sadeghi's non-classicality indicator and the Von Neumann entropy. It is also shown that for the superposition of the squeezed number state and ground number state, the squeezing parameter affects the entanglement feature and Sadeghi's non-classicality indicator increases with the increase of the squeezing parameter.

Abstract Despite progress in the prevention and diagnosis of cancer, current technologies for tumor detection present several limitations including invasiveness, toxicity, inaccuracy, lengthy testing duration and high cost. Therefore, innovative diagnostic techniques that integrate knowledge from biology, oncology, medicinal and analytical chemistry are now quickly emerging in the attempt to address these issues. Following this approach, here we developed a paper-based electrochemical device for detecting cancer-derived Small Extracellular Vesicles (S-EVs) in fluids. S-EVs were obtained from cancer cell lines known to express, at a different level, the αvβ6 integrin receptor, a well-established hallmark of numerous epithelial cancer types. The resulting biosensor turned out to recognize αvβ6-containing S-EVs down to a limit of 0.7*103 S-EVs/mL with a linear range up to 105 S-EVs /mL, and a relative standard deviation of 11%, thus it may represent a novel opportunity for αvβ6 expressing cancers detection.

Abstract Oil-immersed transformers are expensive equipment in the electrical system, and their failure would lead to widespread blackouts and catastrophic economic losses. In this work, an elaborate diagnostic approach is proposed to evaluate twenty-six different transformers in-service to determine their operative status as per the IEC 60599:2022 standard and CIGRE brochure. The approach integrates dissolved gas analysis (DGA), transformer oil integrity analysis, visual inspections, and two Back Propagation Neural Network (BPNN) algorithms to predict the loss of life (LOL) of the transformers through condition monitoring of the cellulose paper. The first BPNN algorithm proposed is based on forecasting the degree of polymerization (DP) using 2-Furaldehyde (2FAL) concentration measured from oil samples using DGA, and the second BPNN algorithm proposed is based on forecasting transformer LOL using the 2FAL and DP data obtained from the first BPNN algorithm. The first algorithm produced a correlation coefficient of 0.970 when the DP was predicted using the 2FAL measured in oil and the second algorithm produced a correlation coefficient of 0.999 when the LOL was predicted using the 2FAL and DP output data obtained from the first algorithm. The results show that the BPNN can be utilized to forecast the DP and LOL of transformers in-service. Lastly, the results are used for hazard analysis and lifespan prediction based on the health index (HI) for each transformer to predict the expected years of service.

Screen-printed copper electrodes have the potential to replace silver and lithium electrodes in printed batteries and sensors owing to the abundance of copper, its competitive electrical properties, and the low cost of raw materials. Herein, copper microparticle-glycerol-based inks were screen-printed onto paper to develop highly conductive electrodes. The conductivity and particle connectivity enhancement of screen-printed electrodes are the main research topics. These parameters translate to usability including increased sensitivity for sensor applications and reduced resistivity for battery electrode applications. CuO nanoparticles of 50 nm were deposited onto the electrodes at a concentration of 1 μl/cm2, which led to a 4-fold decrease in sheet resistivity from 200 to 50 Ω/m2. The increased connectivity and formation of new channels due to the addition of nanoparticles were visualised via field emission scanning electron microscopy. The CuO nanoparticles were developed via a hybrid approach incorporating wet chemistry for high yield and laser ablation for colloidal conductivity and Zeta potential enhancement which reached up to −45 mV. An optimal screen-printing viscosity of 62 mPa s was achieved through a precise 1.95:1 mass ratio of Cu microparticles to glycerol. Heat treatment at 100 °C after screen-printing enhanced particle connectivity by reducing glycerol content in the ink.

The increase in energy valorization of paper sludge and biomass waste through incineration results in a rise in waste paper fly ash (WPFA), often perceived as hazardous and requiring specific treatment. In this study, natural carbonation technology at a pilot scale was employed to mitigate the hazardous nature of WPFA by enhancing the stabilization of metal and metalloid trace elements (MMTE), particularly barium (Ba) and lead (Pb) leaching. Natural carbonation of WPFA was found to be optimal at a water/solid ratio of 0.3 L/kg under natural temperature and humidity conditions. Batch leaching tests based on thermodynamic equilibrium were used to assess MMTE solubility concerning pH in both non-carbonated and carbonated WPFA at natural pH. After 7 days of natural carbonation, the leaching concentration of Ba and Pb was below the legal limit in France. The concentration of Ba and Pb in carbonated samples decreased by 98.5% and 98%, respectively. Analyses using thermogravimetry, X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy demonstrated the increased formation and quantity of calcite (CaCO3) with longer carbonation times, along with the formation of new minerals as BaCO3 and PbCO3, confirming the immobilization of these elements post-carbonation. The leaching behavior and release potential of carbonated WPFA were further evaluated using the four-stage sequential extraction procedure proposed by the European Commission’s Bureau of Reference (BCR). The speciation of Ba and Pb shifted significantly from the soluble substance (F1) at 17.6% and 14.8%, respectively, to the carbonate fraction (F2) at 0.49% and 0.02% after 90 days of carbonation. The percolation water collected during the carbonation process adheres to discharge standards into the sea.

Conventional techniques for sharing paper documents in teleconferencing tend to introduce two inconsistencies: 1) media inconsistency: a paper document is converted into a digital image on the remote site; 2) space inconsistency: a workspace deliberately inverts the partner’s handwriting to make a document easy to read. In this paper, we present a novel system that eliminates these inconsistencies. The media and space inconsistencies are resolved by reproducing a real paper document on a remote site and allowing a user to handover the paper document to a remote partner across a videoconferencing display. From a series of experiments, we found that reproducing a real paper document contributes to a higher sense of information sharing. We also found that handing over a document enhances a sense of space sharing, regardless of whether the document is digital or paper-based. These findings provide insights into designing systems for sharing paper documents across distances.

Since the last two decades, the use of natural fiber reinforced polymer composites has garnered significant application considerations over the synthetic fiber reinforced composites due to their numerous advantages and unique properties. Likewise, epoxy resin has attracted the interest of many researchers for composite synthesis, basically because of its chemical stability, thermal and mechanical characteristics. Hence, the primary aim of this study was to investigate the influence of dombeya fiber and paper particulate on the physical and mechanical properties of dombeya fiber and paper particulate-reinforced polymer composites for structural applications. Dombeya fiber and paper particles are renewable and biodegradable materials, thereby making them environmentally friendly materials to replace synthetic materials. Hand lay-up technique was utilized to fabricate the hybrid-reinforced biocomposites after which they were subjected to mechanical, wear, density, and moisture absorption properties. The surface morphology of the fractured surface was also analyzed to investigate its microstructural features. It was discovered from the results that hybrid biocomposites demonstrated improved properties over the unreinforced composite, with composites from 9-wt% dombeya fiber-paper particles reinforced biocomposite exhibiting the most suitable properties with commensurate density with the unreinforced epoxy matrix. These obtained characteristics support the material as a suitable material for biomedical apparatus application such as orthopedic implants, surgical instruments, and bone fixation devices.

Abstract Personalized healthcare management is an emerging field that requires the development of environment‐friendly, integrated, and electrochemical multimodal devices. In this study, the concept of integrated paper‐based biosensors (IFP−Multi) for personalized healthcare management is introduced. By leveraging ink printing technology and a ChatGPT–bioelectronic interface, these biosensors offer ultrahigh areal‐specific capacitance (74633 mF cm−2), excellent mechanical properties, and multifunctional sensing and humidity power generation capabilities. More importantly, the IFP−Multi devices have the potential to simulate deaf‐mute vocalization and can be integrated into wearable sensors to detect muscle contractions and bending motions. Moreover, they also enable monitoring of physiological signals from various body parts, such as the throat, nape, elbow, wrist, and knee, and successfully record sharp and repeatable signals generated by muscle contractions. In addition, the IFP−Multi devices demonstrate self‐powered handwriting sensing and moisture power generation for sweat‐sensing applications. As a proof‐of‐concept, a GPT 3.5 model‐based fine‐tuning and prediction pipeline that utilizes recorded physiological signals through IFP−Multi is showcased, enabling artificial intelligence with multimodal sensing capabilities for personalized healthcare management. This work presents a promising and ecofriendly approach to developing paper‐based electrochemical multimodal devices, paving the way for a new era of healthcare advancements.

Chemical wastes, such as synthetic dyes and coloring agents, pose significant concerns due to their detrimental impact on human health and ecosystems. As an eco-friendly alternative, the study of natural dyes and coloring agents has gained momentum over the last decade, owing to their biodegradability and reduced environmental and health risks. Here, we report a novel approach employing a butterfly pea anthocyanin paper-based sensor to quantify Fe(III) ions in water. Compared to previous green sensing techniques reliant on heavy instrumentations, this approach offers enhanced accessibility, cost-effectiveness, and user-friendliness. Notably, this study is the first example of natural dye sensing on a capillary microfluidics system. The capillary-driven microfluidic system ensures user-friendly operation and allows the sensing platform to be directly immersed in water without reagent loss. The device's design involves drying the butterfly pea-derived anthocyanin reagent within a pH-controlled paper substrate embedded in the capillary-driven microfluidic system. Smartphone-based colorimetric signal generation and quantification was achieved within seconds for a working range of 50–800 mg/L, with the device's detection limit of 43 mg/L using ImageJ and 55 mg/L using the smartphone app. This green sensing methodology has the potential to be used for groundwater sources with elevated Fe(III) levels. Additionally, this platform can be used in chemistry educational settings as an effective means to understand fundamental concepts such as acid-base reactions, base strength, ionic equilibrium, and metal complexation in a user-friendly microfluidic system.

This research provides an in-depth assessment of two paper yarn variants, examining their structural, functional, and performance characteristics. These yarns demonstrated favorable properties, including suitable linear density, twist, typical cellulosic functional groups as confirmed by Infrared spectroscopy, minimal hairiness, moisture transfer, and creditable mechanical strength. These yarns have flat layered cross-sections and grooved longitudinal surfaces. In addition, a low hairiness index (1.3–1.33) further acknowledged their smooth surface. Their remarkable evenness (15.86% and 7.08%) supported their effective wicking properties. Despite average breaking strength (0.77 cN/dTex and 1.05 cN/dTex) and moderate elongation, these yarns exhibited exceptional water-washing resistance and retained over 89% breaking strength after 15 washes. This study ranks these paper yarns as highly suitable for durable clothing fabrics, providing promising sustainable alternatives in the textile industry.

Carbon fiber paper is one of the most important substrates used in the gas diffusion layer of the polymer electrolyte membrane fuel cell. A novel approach to creating carbon fiber paper using polyacrylonitrile compounds was proposed in this study. The technique incorporated varying amounts of carbon materials, including carbon black (Vulcan), graphite powder, and carbon nanotubes. Polyacrylonitrile carbon materials were prepared through the spinning process, followed by oxidative stabilization under an oxygen atmosphere at a temperature range of 160–300 °C as the first step. The pliable material undergoes a conversion process to create a compound or ladder that is non-plastic, which is then stabilized in an N2 atmosphere. The fibers are then pre-carbonized at temperatures ranging from 300 to 600 °C and further carbonized between 600 and 1100 °C. After that, Teflon is added and the resulting fibers are made into sheets during the production process. Finally, physical measurements and electrochemical methods such as: checking the amount of water absorption, scanning electron microscope (SEM), chronopotentiometry, electrochemical impedance spectroscopy, electron resistance of carbon sheet, double layer capacitance, and surface roughness parameter were evaluated. The results indicate that the best performance is related to CP7 carbon paper (with a 30–70 % combination of polyacrylonitrile and carbon black).

The contamination characteristics, migration patterns and health risks of per- and polyfluoroalkyl substances (PFAS) were investigated in 66 Chinese paper products by using target and non-target screening methods. Among 57 target PFASs, 5 and 6 PFASs were found in the hygiene paper products (

We present a facile one-step hydrothermal method for the fabrication of free-standing graphene paper using aqueous graphene oxide (GO) dispersion as the starting material. Notably, the method does not require the use of any additives for the reduction and preparation of the graphene paper. The resulting graphene paper exhibits a high degree of reduction, as confirmed by X-ray photoelectron spectroscopy (XPS) analysis, revealing a carbon-to-oxygen (C/O) ratio of ∼7. The fabricated graphene paper also demonstrates excellent conductivity, with a measured value of ∼1900 S/m, and sheet resistance of around 100 Ω/sq. Furthermore, the energy storage capability of the graphene paper based electrode is evaluated, which shows a promising specific capacity of 249 F/g at a current density of 1 A/g in 1M H2SO4 as the ionic medium. Additionally, the electrode has also demonstrated remarkable energy density and power density values of 28.68 Wh/Kg and 455 W/Kg, respectively. Overall, the resulting graphene paper exhibits high conductivity and excellent electrochemical performance, making it a promising candidate for various energy storage applications.

A ratiometric fluorescence sensor platform with easy-to-use and accurate is nanoengineered for NH3 quantitative detection and visual real-time monitoring of chicken freshness using smartphones. The ratiometric fluorescent probe formed by combining the zinc ion complex and carbon dots has a double-emitted fluorescence peak. The fluorescence intensity of the complex changed can be clearly observed with the increase of the concentration of ammonia solution under 365 nm wavelength excitation. In order to detect NH3 concentration in gaseous phase, a portable paper-based sensor was designed. The sensor had a good linear relationship with NH3 concentration ranging from 10.0 to 90.0 μmol/L and the LOD value was 288 nM. This fluorescent paper-based sensor was used to check the freshness of chicken breast refrigerated at 4 °C, revealed observable shifts from blue to green. The fluorescent paper-based sensor can detect NH3 concentration in real time and simplify the monitoring process of meat freshness while ensuring accuracy and stability.

Abstract Autistic individuals often experience a wide range of barriers and challenges with employment across their lifetime. Despite their strengths and abilities to contribute to the workforce, many individuals experience unemployment, underemployment and malemployment. However, current supports and services are often inadequate to meet their needs. To allow autistic people to achieve vocational success, we explore four contributors to employment and expand upon the issues and potential solutions to each. These positions include the importance of family support and its consideration in the application of vocational support interventions, addressing transitional needs for autistic youth, building employer capacity, and conducting research that advises the development of meaningful programs and policies. By advocating for these positions, we aim to foster greater inclusivity and support for individuals with ASD in the workplace.

Objective: It was aimed to emphasize the relationship between domestic violence and suicides by evaluating the cases referred to prepare a report due to domestic violence, suicide attempt and homicide. Methods: From 2014, when Muğla Training and Research Hospital Forensic Medicine Polyclinic was established, until the end of 2022, cases who applied to our polyclinic due to suicide attempt and domestic violence were analyzed separately. The records of the cases who applied due to suicide attempt and those who applied for domestic violence before/after the attempt were evaluated. Results: In the 9-year period between 2014-2022, a total of 14.821 reports were prepared in Muğla Training and Research Hospital Forensic Medicine Polyclinic, and 1.099 (7.4%) of them were reported due to domestic violence. In 763 (69.4%) cases reported due to domestic violence, the perpetrator was the spouse/partner, and in the remaining cases, the violence came from other domestic individuals. 686 (89.9%) cases of spousal/partner violence and 180 (53.6%) of cases of nonspousal/partner domestic violence belong to women.631 (4.2%) of the reports were due to suicide attempt, and 402 (63.7%) of them belonged to women. It was determined that 17 of the female cases who attempted suicide were reported due to violence by spouse/partner before/after the attempt, and in 19 (4.7%) of them, including domestic violence in 2 cases, by spouse/partner and other domestic individuals. In men, the number of cases in this group is 5, and the rate is 2.2%. Only 1 of them is spousal violence and the others are domestic violence. According to results obtained, the rate of suicide attempt in cases of spousal/partner violence was 2.2%, while the rate of suicide attempt was 6.8% in cases diagnosed with mental disorder due to spousal/partner violence. Conclusion: It has been suggested that detailed evaluation of both suicide attempters and victims of domestic violence will contribute to the solution of both social problems.

Objectives: This review aimed to determine the form, results, and barriers to exercise-based rehabilitation programs for severe COVID-19 survivors. Methods: Searching for the article was carried out from August to October 2021. We used the PubMed database as a search media with the keywords ([‘COVID-19’ OR ‘COVID 19’ OR ‘SARS CoV-2’ OR ‘post COVID-19’] AND [‘rehabilitation’]). Original articles and case reports published in the last 2 years (July 2019-2022), written in English, available in full text, and accessible in PDF or HTML format were included. Articles were excluded if they did not fit the research topic after reading the full text. Results: There were a total of 7461 articles found at the initial screening using keywords. In the next screening using the inclusion and exclusion criteria and after reading the whole article, we found 9 articles that matched the topic. Of these, 7 articles were original articles and 2 case reports. All of the articles explained the forms and outcomes of exercise-based rehabilitation in severe cases of COVID-19 survivors. However, no article explained the barriers to rehabilitation. Discussion: Exercise was generally given to increase exercise tolerance in severe COVID-19 survivors in both inpatient and outpatient cardiopulmonary rehabilitation programs. The form of exercise was aerobic, strength, or endurance training, and other forms of exercise such as balance training as well as breathing exercises. The type and intensity of exercises given were tailored to the patient’s needs. Research showed that exercise-based rehabilitation programs resulted in a positive impact on increasing the survivor’s quality of life, functional capability, and exercise tolerance. A previous study explained that barriers to rehabilitation in COVID-19 were related to the patient’s health condition, COVID-19 infectivity, and issues related to health services.

Using the experimental results and data, the thermodynamic characteristics and thermal analysis of the electrical arc of torch electrodes and energy deposition in the waste-incinerator primary designed chamber were investigated. The temperature of arc in the intermediate electrode which is called the float nozzle was measured at 7000-8000 Kelvin based on the input power of 2 kW. The plasma plume temperature implied to be lower than the arc temperature according to the cold gas flow in the nozzle. The efficiency of energy transferring to the plasma plume is dependent on the geometrical electrode and nozzle design, and gas flow rate. After ten seconds, the chamber temperature was measured at 1193 Kelvin by thermocouple with the performance of electrical elements and plasma torch. The chamber temperature increasing in an adiabatic process was calculated at 1230 Kelvin after this time. According to the isothermal approach, the heat flow rate, and conduction loss calculation, the chamber temperature was obtained at about 900-1000 Kelvin. Using two approaches with inevitable approximations, the calculated temperature ranges for arc and plasma plume energy estimation have reasonable compatibility and this led to the road map of optimization and development for future torch planning and waste-incinerator chamber design.

In this work, considering the moment theory propagation of the laser beam with relativistic intensity in thermal quantum plasma is studied. Using the Maxwell equation and dielectric function obtained by the quantum hydrodynamic model, the mathematical equation for the laser beam width parameter is achieved and solved numerically by the fourth-order Runge-Kutta method. The results show that the stronger self-focusing effect is found in the moment theory compared to paraxial approximation. Also, similar to paraxial approximation, with growing Fermi temperature, plasma density and laser intensity, the oscillation frequency of the beam width parameter increases and focusing length decreases which means improving the self-focusing effect. Furthermore, it is seen that behaviors of the critical radius are not similar in the two theories, as in the moment theory, with increasing laser intensity, critical radius decreases until it becomes independent of the beam intensity, but in the paraxial approximation, the critical radius after a minimum value is enhanced with increasing laser intensity.

Gene expression is known as a phenomenon that shapes human life. This very complex phenomenon is formed from two stages: transcription and translation. In this study, we used the Nose-Hoover thermostat to model the effect of ambient temperature on gene expression since temperature regulates the biological clock of living systems. We have used the Lyapunov exponent approach to investigate the effect of control parameters on gene expression, including the degradation rates of messenger RNA and proteins, and to find critical points (phenomenon boundary limits), mRNA, and protein level boundary values. The rate of degradation in the process of protein synthesis has been investigated with the help of the Lyapunov exponent approach. According to this study, the optimal temperature for the production of mRNA molecules by Escherichia coli bacteria is 306 Kelvin. The study also used the chaos approach to show that the faster the mRNA molecules are degraded, the more they are transcribed, and the more chaotic the system becomes.

Entanglement plays a fundamental role in the field of quantum computing and quantum communication. In real conditions, a physical system is never isolated and inevitably interacts with its surroundings. Temperature is one of these effects that mainly reduces entanglement. In real conditions, the system is at a non-zero temperature, which will lead to a mixed state. Therefore, in the present work, the combined thermal entanglement of electron spin-oscillation in an anisotropic two-dimensional quantum dot is investigated using the negativity criterion. The results show that the combined entanglements are strongly dependent on the changes of the controllable parameters, such as the Rashba parameter and the magnetic field. The thermal entanglement between the spin and the assembly of oscillators is zero at absolute zero temperature and reaches a maximum with increasing temperature and then tends to zero asymptotically. This temperature, at which the amount of entanglement reaches its maximum value, can be controlled by changing the magnetic field and the coupling of the Rashba parameter. These two factors also control the rate of reaching the asymptotic state. These results provide a way to control the degree of entanglement between electron degrees of freedom, which is a fundamental requirement of quantum information processing.

In the last two decades, photonic crystals and structures that are based on them (photonic structures) have been examined and have been widely utilized in various optical applications. In this article, a theoretical and numerical model for the propagation of electromagnetic waves in multilayer dielectric structures is developed. The propagation of ultra-short light pulses in multilayer media and microresonators is investigated, and the energy reflection and transmission coefficients depending on the parameters of the environment and duration of the optical pulse are calculated. A method for calculating the transmission and reflection spectra of one-dimensional photonic crystal based on FDTD modeling with the emission of ultra-short optical pulses is proposed. To calculate the transmission and reflection spectrum of a one-dimensional photonic crystal and to simulate the propagation of ultra-short light pulses, in multilayer dielectric structures and microresonators, based on the numerical solution of Maxwell's equations with the finite difference approximation in the space-time domain, is performed.

In this study, The surface plasmon excitations in a dimer structure of closely spaced metallic nanospheres with different radii are investigated using the hydrodynamic model. Initially, an expression was derived to calculate this structure's multipolar surface plasmon excitations. Subsequently, the surface plasmon excitations in the dipole approximation were examined.The surface plasmon excitations in a dimer structure of closely spaced metallic nanospheres with different radii are examined using the hydrodynamic model in this study. It has been observed that the energy of in-phase modes is lower than that of out-of-phase modes in longitudinal or transverse excitations. Furthermore, at each separation distance between the nanospheres, the energy difference between in-phase and out-of-phase longitudinal modes is greater than that of transverse modes. The results show that with an increase in the separation distance between the nanospheres, the energies of in-phase modes increase, and the energies of out-of-phase modes decrease. At large separation distances, two plasmon modes are obtained, with the higher energy mode corresponding to the smaller nanosphere and the lower energy mode corresponding to the larger nanosphere. Finally, the local limit results are presented for comparison.

In this study, the optical and electronic properties of bulk and nano-layer of zinc selenide (ZnSe) and zinc sulfide (ZnS) are investigated. The calculations for solving the many-body Schrodinger equations are performed in the framework of density functional theory using the WIEN2K computational package. The Engel-Vosko and gradient generalized approximation (GGA) treat the exchange-correlation potential. To investigate the electronic and optical properties of zinc selenide and zinc sulfide nano layers, the electronic band structure and the real and imaginary parts of complex dielectric function for the bulk and nano-layer with different thicknesses are calculated and compared. The results of electronic band structures show that the energy band gap of zinc selenide and zinc sulfide nano-layers with various thicknesses decreases to zero and are metal. In contrast, the bulk of zinc selenide and zinc sulfide compounds are semiconductors. The results also show that for each compounds the static dielectric function for the perpendicular and parallel direction to the nano-layer surface is different from the bulk static dielectric function. Comparison between the real parts of complex dielectric function for the bulk and nano-layer shows that absorption of electromagnetic radiation for the ZnSe and ZnS nano-layer in comparison to corresponding bulk results occur in lower energies.

Oxygen (O2) was discovered approximately 250 years ago (Contribution 1), a breakthrough accredited to at least three people: Antoine-Laurent de Lavoisier in France (Antoine Lavoisier), Carl Wilhelm Scheele in Sweden, and Joseph Priestley in England [...]

The insulation performance of transformer bushings is a crucial aspect that directly affects the safe operation of equipment. To diagnose the insulation status of transformer bushings and mitigate the impact of small-sample imbalanced data on diagnostic results, a particle swarm optimization combined with back propagation neural network (PSO-BPNN) and adaptive synthetic sampling (ADASYN) method are employed to fault diagnosis of transformer bushing. Initially, historical fault data of transformer bushings are gathered, and a sample set of dissolved gases in transformer oil with distinct fault categories is established. The ADASYN algorithm is used to synthesize the minority class samples in the original data, which allowed for obtaining balanced fault data. The balanced dissolved gases in oil served as the model input, and the fault status is used as the label output to diagnose the transformer bushings using the PSO-BPNN model. To diagnose the bushings under the original sample set, the back propagation neural network (BPNN), genetic combined with back propagation neural network (G-BPNN), cuckoo search combined with back propagation neural network (CS-BPNN), and PSO-BPNN models are used. The results reveal that the PSO-BPNN model based on ADASYN balanced data exhibited the highest accuracy among the various models for fault diagnosing the insulation status of transformer bushings. This approach effectively mitigate the impact of small sample imbalanced data on diagnostic results, and provide an effective method for assessing the insulation performance of transformer bushings.

Abstract This article presents the results of an experiment designed to study the impact of temperature on the characteristic parameters of creeping discharges. The insulating interfaces consist of a thermally enhanced cellulose surface immersed in mineral oil, palm kernel oil methyl ester (PKOME) and castor oil methyl ester (COME). The study was carried out under a standard negative lightning impulse voltage (1.2/50 μs). The article also presents the complete algorithms for calculating the maximum extension of the discharges, the ionisation rate and the charge produced by them. The results of the study show that temperature favors the propagation of discharges and the ionisation rate. It was observed that liquids with a higher dielectric constant and high electrical conductivity were more exposed to the impact of temperature. The results show ionisation increments of 0.973%/°C, 1.093%/°C and 1.076%/°C in mineral oil (MO), COME and PKOME respectively. The maximum extension of the discharges shows a linear evolution with the applied voltage and temperature but a non-linear increment with the temperature. As for the charge produced, it shows a constant increment with temperature and voltage in each liquid. These values are (5.839%/°C, 1.977%/kV), (6.047%/°C, 2.082%/kV) and (6.177%/°C, 2.113%/kV) respectively in MO, COME and PKOME.

This article proceeds to analyze the Atlante freddo trilogy, focusing particularly on the interplay between fictional creation and the author’s cognizance of crime chronicles explored in his non-fictional works. From this vantage point, Bernardi’s novels emerge as an experimental terrain wherein he probes conceivable narratives, employing the narrative as a pretext to delineate the locales and dynamics of contemporary society. The trilogy by Bernardi directs attention to a spectrum of concerns, encompassing the marginalization of the foreigner, the erosion of the media’s informative function, and the interrelation between minor and major criminal activities. Ultimately, a comparative analysis between Bernardi and Carlotto is introduced, primarily examining ideological and thematic alignments.

Sihem Lazreg,1 Mohamed Hosny,2 Muhammad A Ahad,3 Mazen M Sinjab,4 Riadh Messaoud,5 Shady T Awwad,6 Antoine Rousseau7 1Ophthalmology Cabinet, Blida, Algeria; 2Refractive and Cornea Service, Cairo University Hospitals, Cairo, Egypt; 3Department of Ophthalmology, Anterior Segment Division, King Khaled Eye Specialist Hospital, Riyadh, Saudi Arabia; 4Dr Sulaiman Al Habib Hospital, DHCC, Dubai, United Arab Emirates; 5Department of Ophthalmology, Tahar SFAR University Hospital, Mahdia, Tunisia; 6Department of Ophthalmology, American University of Beirut - Medical Center, Beirut, Lebanon; 7Department of Ophthalmology, Bicêtre Hospital, Paris-Saclay University, Le Kremlin-Bicêtre, FranceCorrespondence: Antoine Rousseau, Pierre Testas Building, Bicêtre Hospital, 78 Rue du Général Leclerc, Le Kremlin-Bicêtre, 94270, France, Tel +33145213690, Email arousseau1010@gmail.comAbstract: In the Middle East and Northern Africa (MENA), dry eye disease (DED) is often misdiagnosed or overlooked. This review summarizes a series of conversations with ophthalmologists in the region around a variety of climatic, lifestyle, and iatrogenic factors that contribute to specific features of DED in the MENA region. These considerations are further classified by patient lifestyle and surgical choices. All statements are based on discussions and formal voting to achieve consensus over three meetings. Overall, a deeper understanding of the disease characteristics of DED specific to MENA can better guide local eyecare practitioners on appropriate management and follow-up care. Additionally, population-based studies and patient and physician education on ocular surface diseases, together with the use of culturally appropriate and language-specific questionnaires can help ease the public health burden of DED in this region.Keywords: ocular surface, regional clinical practice, epidemiology, treatment, patient outcomes

Bamboo, a member of the grass family, is a fast growing and high yielding renewable resource. The popularity of bamboo has risen in recent times owing to its multifaceted and myriad of practical applications. There are unlimited uses of bamboo, therefore proper utilization of this beneficial resource will be useful to the industrial sector. This review provides a comprehensive summary regarding the potential of bamboo as a vital non-wood fibrous raw material for pulp, paper and other allied industries owing to its ability to conserve forests and foster sustainable economic development. Bamboo's abundance, renewability, mechanical strength, and other functional features make it an appealing and potential building biomaterial in the pursuit of sustainable raw materials needed for industrial development. This review provides an in-depth summary and unique perspective on the application of bamboo at a commercial scale in various sectors, thereby encouraging the utilization of this potential material towards environmental sustainability and economic growth.

Metalloid nanoparticles (MNPs) possess unique physicochemical properties but are challenging to create through biological or chemical routes. Using Pulsed Laser Ablation in Liquid (PLAL), Mg–C MNPs are fabricated from powders. The produced nanocolloids were ablated after the target was removed to tailor the particle size. MNPs with a mean size 300 nm could be reduced to 60 nm. Alternatively, MNPs with a mean size of 60 nm could be increased to 90 nm. The increase/decrease in size is controlled by the laser processing parameters and showcases the ability of PLAL for real-world applications that require meticulous control of size. The as-fabricated nanocolloids were successfully inkjet printed on paper, achieving a low resistivity of 75 Ω/square after 60 prints, highlighting their potential in printed electronics. To address a historical research gap, this article explored the impact of PLAL processing parameters, including fluence (1–2 J/cm2), pulse width (0.2–0.9 ns), repetition rate (10–20 kHz), and pH, factors often overlooked which is partly limiting applications. The influence of powder vs rod target on the PLAL process was addressed revealing that powders produce better size control and are easier to handle but they produce lower colloid concentrations.

Demographic ageing in Europe is leading to an increasing need for care and a serious challenge for the sustainability of our social and healthcare systems. Informal carers across the EU currently provide over 80 per cent of all care. If not adequately supported, caring can have many difficult consequences for carers. Carers should not be socially and economically penalised as a result of their caregiving activities. Measures designed to support them should therefore aim to recognise them and their vital role in society, provide them with the essential information and counselling they need, give them access to allowances that offset the costs they face and truly values their contribution, develop flexible working arrangements and care leave schemes to allow them to maintain an active life, and improve the provision of equitable and accessible formal care services to ensure carers can rely on professional alternatives to informal care. This policy paper makes clear why it is necessary to address the challenges faced by young carers. It briefly discusses different forms of support measures and makes recommendations for better support for Young Carers

Foodborne spores are ubiquitous with extremely strong resistance, and pose a serious threat to food safety and human health. Therefore, rapid, sensitive, and selective detection of spores are crucial. In this study, a fluorescent probe was developed based on lanthanide ion (Eu3+)-labeled nano-silver-modified graphene oxide (GO-AgNPs-Eu3+) for the detection of 2,6-dipicolinic acid (DPA), a biomarker unique to spores, to allow quantitative spores detection. The GO-AgNPs-Eu3+ nano-fluorescent probe was loaded onto a polyvinylidene fluoride microfiltration membrane, and a smartphone-assisted portable GO-AgNPs-Eu3+ nanoparticles-based paper visual sensor was designed for rapid on-site quantitative and real-time online detection of spores. The results indicated that the developed probe achieved equilibrium binding with DPA within 5 min, and enhanced fluorescence emission through antenna effect. The fluorescence detection presented a good linear relationship in the DPA concentration range of 0–45 μM, with a DPA detection limit of 4.62 nM and spore detection limit of 104 cfu/mL. The developed sensor showed a change in fluorescence from blue to red with increasing DPA concentration, and this color change was quantitatively detected through smartphone RGB variations, with a detection limit of 13.1 μM for DPA and 6.3 cfu/mL for Bacillus subtilis spores. Subsequently, the sensitivity and selectivity of the developed sensor were verified using actual milk and water samples spiked with B. subtilis spores. The results of this study provided objective technological support for rapid detection of spores, which is important for reducing the occurrence of foodborne diseases and improving food safety.

The manuscript describes a technique for fabrication and validation of a standalone handheld optical biosensor designed for non-invasive monitoring of glucose through saliva. In this cost-effective process, a 3D-printed glucose test strip was filled with sieving paste comprising of cellulose, polyethylene glycol (PEG), polyvinyl alcohol (PVA) and glycerol, onto which, glucose oxidase-peroxidase (GOD-POD) enzymes and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) chromogenic dye were co-immobilized. The enzymatic reaction produced H2O2 as by-product with which the ABTS reacted, leading to colour change on the detection zone of the strip which was detected by the developed glucometer. The in-house developed meter included an optically isolated section in its structure for inserting the strip to prevent interference from the ambient light conditions. The biosensor exhibited a broad detection range of 28–204 mg/dL of glucose concentration, with a sensitivity of 26.89 count/mg/dL and a limit of detection (LOD) at 28 mg/dL, within a response time of 120 s. The device along with strips was validated with clinical samples, comparing salivary glucose levels (SGL) to blood glucose levels (BGL) using a commercial glucometer i.e., Accu-Chek Active. Student's t-test on clinical data yielded p-values of 0.018, 0.01, 0.008, and 0.003 in fasting and post-prandial samples of non-diabetic and diabetic patients respectively, which represents a significant correlation. The device also passed Clarke's error grid analysis and is hence considered medically acceptable. The low-cost and simple-to-use saliva-based glucometer should be ideally suited for mass screening of diabetes as well as day-to-day health check-ups in a non-invasive and painless manner.

Abstract The erratic, intermittent, and unpredictable nature of sweat production, resulting from physiological or psychological fluctuations, poses intricacies to consistently and accurately sample and evaluate sweat biomarkers. Skin‐interfaced microfluidic devices that rely on colorimetric mechanisms for semi‐quantitative detection are particularly susceptible to these inaccuracies due to variations in sweat secretion rate or instantaneous volume. This work introduces a skin‐interfaced colorimetric bifluidic sweat device with two synchronous channels to quantify sweat rate and biomarkers in real‐time, even during uncertain sweat activities. In the proposed bifluidic‐distance metric approach, with one channel to measure sweat rate and quantify collected sweat volume, the other channel can provide an accurate analysis of the biomarkers based on the collected sweat volume. The closed channel design also reduces evaporation and resists contamination from the external environment. The feasibility of the device is highlighted in a proof‐of‐the‐concept demonstration to analyze sweat chloride for evaluating hydration status and sweat glucose for assessing glucose levels. The low‐cost yet highly accurate device provides opportunities for clinical sweat analysis and disease screening in remote and low‐resource settings. The developed device platform can be facilely adapted for the other biomarkers when corresponding colorimetric reagents are exploited.

The effect of foreign trade on economic growth and development is one of the basics in the scientific literature. The countries' use of their production power on the basis of international trade contributes to economic growth periodically in different ways. Although it varies according to the countries, the manufacturing industry and sub-sectors have a significant impact on foreign trade figures. The relationship between the development achieved by the sectors in international trade and economic growth is important in terms of determining the leading sectors of development. In this study, it is aimed to examine the causality relationship between the growth in the Turkish economy and the foreign trade data of the paper and paper products industry. Export and import growth rates and GDP (economicgrowth) values of the paper and paper products industry are used and cover the 2002-2021 period. According to the results of the Granger causality test applied over the VAR model, there is a one-way causality relationship from exports to economic growth, from economic growth to import, and from export to import.

Art paper made of betel nut husk fibre and paper waste is one example of an innovative product. Therefore, an analysis of the technical and financial feasibility of this innovation needed to be conducted. This research aimed to determine the technical and financial feasibility of the production business of art paper from betel nut husk fibre and paper waste. The technical aspect will focus on the technology utilized, primary raw material and additional raw material, production capacity, and any workforce involved in the business. Meanwhile, the financial aspect will emphasize the calculation of the Main Production Cost (MPC), Break Even Point (BEP), Business Efficiency (R/C Ratio), Payback Period (PP), Net Present Value (NPV), and Internal Rate of Return (IRR). The calculation result of the feasibility analysis shows that Production Cost (HPP) is IDR 12,786.00, BEPunit is 9,271 paper sheet, BEP (IDR) is IDR 148,326,906.00, R/C Ratio is 1.56, PP will be for 2.2 years, NPV is IDR 2,078,713,958.00, and IRR is 68.36%. Based on this result, this business on betel nut husk fibre and paper-based waste art paper is considered worth running.

Germany’s public broadcasters, along with local newspapers, have consistently ranked among the top three most trusted news sources in Germany. Yet growing criticism of mandatory fees and recent revelations about public broadcasters’ misuse of funds have put into question the health of Germany’s news and information infrastructure. In fact, a perfect storm appears to be brewing: precarious working conditions, exacerbated by cutbacks in the wake of Covid-19 and the emergence of so-called zombie papers. These papers, published without a local staff, reporters, or newsrooms, threaten to complicate audiences’ perceptions of news credibility and trust. This study explores Germany’s emerging news deserts by examining the rise of zombie newspapers in two states, one in the Western and one in the Eastern part of the country. Analyses of existing literature through the lens of institutional political economy and of interviews with key informants show that Germany, despite its strong federalized system, is following in US footsteps by creating journalist-free zones. A network of hard-to-follow corporate collaborations is endangering the foundations of post-war Germany’s media system: pluralism and media diversity.

A new method was proposed for point-of-care testing (POCT) of immunosuppressants in blood using thin-layer paper spray ionization and a miniature mass spectrometer. The aluminum thin-layer plate was used as paper spray substrate, and cut into an equilateral triangle. Aliquots of 10 μL blood sample were loaded on the aluminum thin-layer plate, and then 20 μL methanol was dropped as elution/spray solvent. The tip of the triangular plate was placed 1.0 cm in front of the discontinuous atmospheric pressure interface (DAPI) of the miniature mass spectrometer. When the spray voltage was applied, the sample was eluted from the triangular plate and formed paper spray ionization at the tip. Coupled with the miniature mass spectrometer, five immunosuppressants were detected under negative ion mode. The precursor ions ［M-H］- of tacrolimus, sirolimus, everolimus, ciclosporin A, and mycophenolic acid are m/z 802.6, 912.6, 957.1, 1 200.8, 319.1, and product ions are m/z 560.2 and 604.3, m/z 590.3 and 321.2, m/z 590.3 and 365.2, m/z 1 088.8, m/z 287.4 and 275.1, respectively. Based on the observed signal-to-noise ratio (S/N) of the most intense tandem mass spectrometry (MS/MS) fragment peaks and using the S/N=3 and 10 as the criteria, the limits of detection (LODs) and quantitation (LOQs) are estimated to be 0.5-5 mg/L and 1-10 mg/L, respectively. The internal standard method was used for quantitative analysis, and indapamide was used as the internal standard compound. Sufficient linearity for each analyte is obtained with the correlation coefficients (r) greater than 0.99. The proposed method displays good recoveries in the range of 91.0%-114.3% with the relative standard deviations (RSDs) less than 8.4%. Moreover, the developed method was used for the analysis of blood samples, which spiked with tacrolimus, sirolimus, everolimus, cyclosporine A and mycophenolic acid at the concentration of 100 mg/L. The analytical results demonstrated the consistency between the proposed method and the traditional liquid chromatography-mass spectrometry (LC-MS) method. The entire analysis procedure can be completed within 1 min. The proposed method is simple, fast, accurate, efficient, and suitable for POCT of immunosuppressants in blood.

This study evaluated the production of marine biodegradable plastics, specifically polyhydroxyalkanoates (PHAs), using waste paper from food containers as a novel material source. The results showed that adding dilute sulfuric acid as a pretreatment may have a negative impact on enzyme hydrolysis efficiency. Without pretreatment, the highest glucose concentration was observed in the 50-min heating group. In the experimental group with 1% dilute sulfuric acid as a pretreatment, the highest average glucose concentration was observed in the 25-min treatment group. In flask scale experiments, the C/N ratio was controlled at 10, 20, and 30. The results showed that when the C/N ratio was 10, the PHA/CDM ratios were 16.3 and 23.6 at 48 and 72 h, respectively. After 96 h of cultivation using hydrolysis liquid from the waste paper container as the sole carbon source in a 5-L scale experiment, the PHA/CDM ratio was 28.7 and the PHA concentration was 0.95 g/L. The potential bacterial strain in this study was confirmed to be a Bacillus genus bacterium after strain identification. The signal peaks indicated that the PHA obtained from the Bacillus sp. production process was PHB.

Purpose: Flattering emails are crucial in tempting authors to submit papers to predatory journals. Although there is ample literature regarding the questionable practices of predatory journals, the nature and detection of spam emails need more attention. Current research provides insight into fallacious calls for papers from potential predatory journals and develops a toolkit in this regard. Methods: In this study, we analyzed three datasets of calls for papers from potential predatory journals and legitimate journals using a text mining approach and R programming language. Results: Overall, most potential predatory journals use similar language and templates in their calls for papers. Importantly, these journals praise themselves in glorious terms involving positive words that may be rarely seen in emails from legitimate journals. Based on these findings, we developed a lexicon for detecting unsolicited calls for papers from potential predatory journals. Conclusion: We conclude that calls for papers from potential predatory journals and legitimate journals are different, and it can help to distinguish them. By providing an educational plan and easily usable tools, we can deal with predatory journals better than previously.

Abstract Efficient removal of mold stains becomes an important research topic for paper conservation. In this study, a cleaning scheme based on the combination of bioenzymes and biosurfactants was explored. Morphological and molecular biology identifications were first jointly applied to identify the dominant strains sampled from five ancient books that are stored in the same environment. Cellulolytic experiments were then conducted to evaluate the cellulose degradation ability of the strains according to the cellulolytic digestive index. Finally, paper Mockups for the ancient books were constructed to investigate the most effective combination of bioenzymes and biosurfactants in removing mold stains as well as its effect on the paper’s physical properties. The result concluded that the combination of 3% papain, 7% of sophorolipid or 7% of betaine, and distilled water, achieved optimal stain removal effect with over 50% cleaning rate at 35 °C, after 30 min of infiltration. The maximum color difference of the paper material after cleaning was around 0.60, pH was between 7.45 and 7.79, and no significant changes in tensile strength were observed. At the same time, Sophorolipid and Betaine both have superior deacidification, anti-acidification, anti-aging, and reinforcement capabilities, which can provide extra support to the fibrous structure in addition to cleaning the paper materials. The microbial contamination cleaning agent proposed in this study shows promising application prospects in conserving mold-contaminated paper artifacts.