Search

Although CRISPR-based nucleic acid detection has great potential in point-of-care testing due to its simplicity, it has been rarely integrated into paper-based analytical devices (PADs), which are attractive platforms to simplify assays. This work introduces a CRISPR-assisted nucleic acid quantification approach integrated into a PAD with signal readout by a personal glucose meter (PGM). Retention of magnetic beads by filter paper and pre-deposition of all required reagents by freeze-drying stabilized with trehalose enabled the indirect quantification of human papilloma virus (HPV) DNA through a PGM readout without complicated user intervention and complex reagent handling. The calculated limit of detection was 57 pM, which is comparable with other amplification-free CRISPR-based assays detecting nucleic acids. The fully integrated device exhibited good storage stability for up to 4 weeks, suggesting its applicability toward practical point-of-care nucleic acid quantification. [ABSTRACT FROM AUTHOR]

The first step in blood testing necessitates blood separation to obtain an adequate volume of plasma. Traditional centrifugation is bulky, expensive and electricity-powered, which is not suitable for micro-scale blood plasma separation in point-of-care testing (POCT) cases. Microfluidic paper-based plasma separation devices present a promising alternative for plasma separation in such occasions. However, they are limited in terms of plasma yield, which hinders analyte detection. Herein, we proposed a humidity-enhanced paper-based microfluidic plasma separation method to address this issue. Specifically, paper was first treated by blood-typing antibodies, then samples of whole blood were introduced into the prepared paper. After waiting for 5 min for RBC agglutination and plasma wicking under high humidity, micro-scale plasma separation from whole blood was achieved. As a result, an extremely high plasma yield of up to 60.1% could be separated from whole blood through using Xuan-paper. Meanwhile, the purity of plasma could reach 99.99%. Finally, this innovative approach was effortlessly integrated into distance-based glucose concentration detection, enabling rapid determination of blood glucose levels through naked-eye observation. Considering the simplicity and inexpensiveness of this method, we believe that this technology could be integrated to more paper-based microfluidic analytical devices for rapid and accurate detection of plasma analytes in POCT. [ABSTRACT FROM AUTHOR]

Paper-based microfluidics combined with potentiometric measurement has emerged as an attractive approach for detecting various chemical ionic moieties. Detection of heavy metal ions, using paper substrates as solution sampling and delivery systems remains challenging despite efforts to introduce several physico-chemical paper substrate modifications to stop adsorption of ions onto the paper substrates. This study quantitatively investigates the adsorption of heavy metal ions on the paper substrates during paper-based potentiometric measurements and explains the super-Nernstian response of potentiometric sensors through local depletion of heavy metal ions from the solution. Consequently, based on the investigated ion adsorption, a corrective potential protocol was established for the electrodes coupled with paper-based solution sampling by predicting interference free sensor response from paper-based measurement. Furthermore, the ion adsorption was also recorded for mixed metal ion solutions to understand competitive primary/interfering ions adsorption onto the paper substrates and establish corrective measures to predict interference free sensor response. In this method, no modifications of the paper substrates are necessary before actual potentiometric measurements. The proposed corrective protocol allows prediction of sensor response based on the paper-based solution sampling potentiometric measurement, providing a simple methodological approach based on correction of potential readout of the potentiometric sensor, thus completely resigning from the need of modifying paper substrate for measurements of heavy metal ions. [ABSTRACT FROM AUTHOR]

The accumulation of plastic packaging wastes in the natural environment highlights the significance of sustainable alternatives. Paper is widely used as a biodegradable packaging material, but poor mechanical strength, barrier properties, and water resistance limit its utility. Typical paper coating materials applied to overcome such drawbacks, such as polyethylene (PE) and ethylene vinyl alcohol (EVOH), are not desirable for sustainability due to environmental persistence. Here, we report a biodegradable, biocompatible, robust, and high-barrier paper coating strategy using boric acid-crosslinked poly(vinyl alcohol) (PVA). Various crosslinked-PVA solutions were prepared using boric acid (BA) and hydrochloric acid (HCl) as a crosslinker and an acid catalyst, respectively. The solutions were coated onto the Kraft paper (KP) through facile bar coating with epichlorohydrin (ECH) as a binder (henceforth referred to as coated papers). The coated papers (KP-P, KP-PB, KP-PBH) show remarkably improved oxygen (∼0.89 cc m−2 d−1) and water vapor (∼5.17 g m−2 d−1) barrier properties as well as tensile strength (∼53.0 MPa) that is retained in moist conditions. The coated papers were significantly mineralized into CO2 (59.2–81.6% over 111 d) in the simulated marine environment biodegradation test. Depolymerization of polymer chains and surface degradation of coated papers are evidenced via FT-IR and SEM, respectively. The microcosm test revealed that the intensive disintegration of the coated papers is synergistically driven by both biotic and abiotic factors (i.e., mechanical stress). Moreover, the in vitro biocompatibility tests employing human embryonic kidney and mouse embryonic fibroblast cells, and in vivo biocompatibility test with mice suggest that the coated papers are highly biocompatible. This work provides a promising strategy for paper packaging that enhances packaging performance without compromising environmental sustainability. [ABSTRACT FROM AUTHOR]

Flexible sensors capable of continuously monitoring surface moisture and respiratory status play a crucial role in human health monitoring. However, manufacturing flexible humidity sensors at low cost remains challenging in traditional manufacturing industries. This study introduces a humidity sensor prepared by impregnating paper with LiCl solution and using carbon nanotube-carboxymethyl cellulose composite paper-based fibers to fabricate interdigital electrodes. This sensor exhibits high sensitivity to gas humidity due to its flexible and porous electrode structure and moisture-sensitive substrate. The prepared porous fiber paper-based humidity sensor (PLFC) is used for detecting small amounts of gas humidity ranging from 33% RH to 98% RH, with a response time of only 500 ms and a linearity of R2 = 0.960. In terms of human health monitoring, it can continuously monitor respiratory rate and amplitude and non-contactly perceive the humidity status of body parts. By reflecting the tester's physiological condition based on surface humidity, it is highly beneficial for patient recovery care and health preservation. Therefore, the design and ideas proposed in this work are of significant importance for the future development and application of wearable respiratory sensors and moisture sensors. [ABSTRACT FROM AUTHOR]

Paper-based microfluidic devices offer an ideal platform for biological and environmental detection because they are low-cost, small, disposable, and fill by natural capillary action. In this tutorial review, we discuss the surface modification of paper-based microfluidic devices with functional polymers using the initiated chemical vapor deposition (iCVD) process. The iCVD process is solventless and therefore ideal for coating cellulose paper because there are no surface tension effects or solvent compatibility issues. The process can also be scaled up for roll-to-roll manufacturing. The chemical functionality of the iCVD coating can be tuned by varying the monomer and the structure of the coating can be tuned by varying the processing parameters. [ABSTRACT FROM AUTHOR]

In the face of worsening water quality and escalating water environmental emergencies, this study developed a paper-based microfluidic disk for rapid, on-site determination of ammonia nitrogen, nitrates, nitrites, and phosphates in water. The method utilizes centrifugal microfluidics and paper-based technology, thus simplifying the operation while eliminating the need for on-site reagent preparation. Experimental results demonstrate that the disk requires only 80 microliters of a water sample and 2 minutes to complete the quantitative analysis of the four nutrients, with a coefficient of variation below 1.72% and spike recoveries ranging from 92% to 113%. The development of the disk provides an effective and rapid, on-site testing tool for water quality analysis. [ABSTRACT FROM AUTHOR]

Bimetallic Au@Ag nano-sea urchins (Au@Ag NSUs) functionalized with methimazole were synthesized and combined with paper tips as efficient surface-enhanced Raman scattering (SERS) substrates for ultrasensitive Cr(VI) detection. The redox reaction between methimazole and Cr(VI) ensured the reliability of quantitative Cr(VI) analysis. When droplets were continuously dropped on the tip of the paper, based on the gravity effect, the nanoparticles achieved enrichment at the front end of the tip, which further improved the sensitivity of detection. The detection limit is as low as 0.956 ng L−1, demonstrating its excellent performance in ultrarace Cr(VI) detection. Additionally, the SERS sensor was successfully applied to the detection of Cr(VI) in real water samples, such as lake water and tap water, indicating its wide application potential in environmental monitoring. This study not only provides an efficient and reliable new method for detecting Cr(VI) but also shows the great prospect of paper-based SERS sensors in practical applications. [ABSTRACT FROM AUTHOR]

Plastic pollution at the nanoscale continues to pose adverse effects on environmental sustainability and human health. However, the detection of nanoplastics (NPLs) remains challenging due to limitations in methodology and instrumentation. Herein, a "green approach" for surface-enhanced Raman spectroscopy (SERS) was exploited to detect polystyrene nanospheres (PSNSs) in water, employing untreated filter paper and a simple syringe-filtration set-up. This SERS protocol not only enabled the filtration of nano-sized PSNSs, which are smaller than the pore size of the ordinary filter paper, but also offered SERS enhancement by utilizing quasi-spherical-shaped silver nanoparticles (AgNPs) as the SERS-active substrate. The filtering of NPLs was accomplished by adding an aggregating agent to the nanoparticle mixture, which caused the aggregation of NPLs and AgNPs, resulting in a larger cluster and more hot spots for SERS detection. The optimal aggregating agent and its concentration, as well as the volume ratio between the AgNPs and NPLs, were also optimized. This SERS method successfully detected and quantified PSNSs of various sizes (i.e., 100, 300, 460, 600, and 800 nm) down to a limit of detection (LOD) of about 0.31 μg mL−1. The method was also validated against the presence of several interferents (i.e., salts, sugars, amino acids, and surfactants) and was proven practical, as evidenced by the detection of 800nm PSNSs in drinking and tap water (LODs of 1.47 and 1.55 μg mL−1, respectively). [ABSTRACT FROM AUTHOR]

The demand for flexible pressure sensors with high performance is increasing with the growing wearable technology market. According to the developing requirement for green electronics, paper-based sensors, which are more environmentally friendly, have received more and more attention. However, the intrinsic mechanical properties of paper materials limit the sensing performance of paper-based sensors, such as restricted working range and response bandwidth. Herein, a rigid–soft hybrid design strategy is proposed to improve the sensing performance of paper-based pressure sensors, and bioinspired microstructures are introduced into the architecture of sensors for further improvement. As a result, the prepared paper-based pressure sensor has a faster response/recovery speed (<50 ms), a wide sensing range (1 MPa) and frequency response bandwidth (0.05–1000 Hz) and excellent cycling stability (5000 cycles). In addition, the paper-based pressure sensor is superhydrophobic with a water contact angle of 152.62°. Based on the excellent sensing performance and waterproofness, the paper-based pressure sensor can be used as a wearable device for detecting joint movements or gait of humans/robots in both air and underwater. In addition, it can be used to send communication signals, showing great potential for applications in future underwater rescue. [ABSTRACT FROM AUTHOR]

The increasing demand in healthcare for accessible and cost-effective analytical tools is driving the development of reliable platforms to the customization of therapy according to individual patient drug serum levels, e.g. of anti-psychotics in schizophrenia. A modifier-free microfluidic paper-based electroanalytical device (μPED) holds promise as a portable, sensitive, and affordable solution. While many studies focus on the working electrode catalysts, improvements by engineering aspects e.g. of the electrode arrangement are less reported. In our study, we demonstrate the enhanced capabilities of the 3D electrode layout of μPED compared to 2D μPED arrangements. We especially show that screen printing can be employed to prepare 3D μPEDs. We conducted a comparison of different 2D and 3D electrode arrangements utilizing cyclic voltammetry in [Fe(CN)6]3−/4−, along with square-wave voltammetry for clozapine (CLZ) sensing. Our findings reveal that the utilization of the 3D μPED leads to an increase in both the electrochemically active surface area and the electron transfer rate. Consequently, this enhancement contributes to improve sensitivity in the CLZ sensing. The 3D μPED clearly outperforms the 2D μPED arrangement in terms of signal strength. With the 3D μPED under the optimized conditions, a linear dose–response for a concentration range from 7.0 to 100 μM was achieved. The limit of detection and sensitivity was determined to be 1.47 μM and 1.69 μA μM−1 cm−2, respectively. This evaluation is conducted in the context of detection and determination of CLZ in a human blood serum sample. These findings underscore the potential of the 3D μPED for future applications in pharmacokinetic analyses and clinical tests to personalize the management of schizophrenia. [ABSTRACT FROM AUTHOR]

Conventional affinity-based colorimetric enzyme-linked immunosorbent assay (ELISA) is one of the most widely used methods for the detection of biomarkers. However, rapid point-of-care (POC) detection of multiple cancer biomarkers by conventional ELISA is limited by long incubation time, large reagent volume, and costly instrumentation along with low sensitivity due to the nature of colorimetric methods. Herein, we have developed a reusable and cost-effective paper-in-polymer-pond (PiPP) hybrid microfluidic microplate for ultrasensitive and high-throughput multiplexed detection of disease biomarkers within an hour without using specialized instruments. A piece of pre-patterned chromatography paper placed in the PMMA polymer pond facilitates rapid protein immobilization to avoid intricate surface modifications of polymer and can be changed with a fresh paper layer to reuse the device. Reagents can be simply delivered from the top PMMA layer to multiple microwells in the middle PMMA layer via flow-through microwells, thereby increasing the efficiency of washing and avoiding repeated manual pipetting or costly robots. Quantitative colorimetric analysis was achieved by calculating the brightness of images scanned by an office scanner or a smartphone camera. Sandwich-type immunoassay was performed in the PiPP hybrid device after the optimization of multiple assay conditions. Limits of detection of 0.32 ng mL−1 for carcinoembryonic antigen (CEA) and 0.20 ng mL−1 for prostate-specific antigen (PSA) were obtained, which were about 10-fold better than those of commercial ELISA kits. We envisage that this simple but versatile hybrid device can have broad applications in various bioassays in resource-limited settings. [ABSTRACT FROM AUTHOR]

Isothermal nucleic acid amplification tests (NAATs) are a vital tool for point-of-care (POC) diagnostics. These assays are well-suited for rapid, low-cost POC diagnostics for infectious diseases compared to traditional PCR tests conducted in central laboratories. There has been significant development of POC NAATs using paper-based diagnostic devices because they provide an affordable, user-friendly, and easy to store format; however, the difficulties in integrating separate liquid components, resuspending dried reagents, and achieving a low limit of detection hinder their use in commercial applications. Several studies report low assay efficiencies, poor detection output, and poorer limits of detection in porous membranes compared to traditional tube-based protocols. Recombinase polymerase amplification is a rapid, isothermal NAAT that is highly suited for POC applications, but requires viscous reaction conditions that has poor performance when amplifying in a porous paper membrane. In this work, we show that we can dramatically improve the performance of membrane-based recombinase polymerase amplification (RPA) of HIV-1 DNA and viral RNA by employing a coin cell-based vibration mixing platform. We achieve a limit of detection of 12 copies of DNA per reaction, nearly 50% reduction in time to threshold (from ∼10 minutes to ∼5 minutes), and an overall fluorescence output increase up to 16-fold when compared to unmixed experiments. This active mixing strategy enables reactions where the target and reaction cofactors are isolated from each other prior to the reaction. We also demonstrate amplification using a low-cost vibration motor for both temperature control and mixing, without the requirement of any additional heating components. [ABSTRACT FROM AUTHOR]

Serum contains rich elemental information, and the elemental analysis of the serum using laser-induced breakdown spectroscopy (LIBS) can help with the diagnosis and treatment of cancer. In this work, serum specimens from breast cancer patients were used as samples, and the elements Mg, Ca, and K were analyzed using LIBS. Silver nanoparticles (Ag NPs) were introduced to enhance spectral emission intensities, and this technique is known as nanoparticle-enhanced LIBS (NELIBS). An Ag NP-coated filter paper (Ag NP paper) substrate was prepared and was compared with silicon and aluminum substrates for NELIBS analysis. The Ag NP paper substrate showed lower spectral intensity variances and better elemental distribution uniformity due to the reduced coffee-ring effect compared with silicon and aluminum substrates. The enhanced effect of the Ag NP paper was optimized by adjusting serum volume and Ag NPs concentration. It was found that Mg, Ca, and K required different optimal conditions for spectral enhancement. The highest enhancement factors (EF) for Mg, Ca, and K were 1.85, 1.76, and 3.10, respectively. The electron temperature (Te) and electron number density (Ne) of NELIBS plasmas were measured using the Boltzmann plot and Stark broadening methods and compared with those of the normal LIBS plasmas. The Te and Ne of the NELIBS and normal LIBS samples were generally comparable with each other. Higher Ag NP concentrations led to lower Te values for NELIBS plasmas. [ABSTRACT FROM AUTHOR]

Non-enzymatic electrochemical blood glucose sensors often suffer from issues such as requiring an alkaline environment, limited monitoring range, and poor anti-interference properties. Carbon substrates have been demonstrated to improve the performance of non-enzymatic sensors, but complex and energy-consuming manufacturing processes restrict their use. Herein, a simple and green approach for the preparation of 3D porous Au/Au-Pt networks (PAAPNs) is proposed using tissue paper for recycling as the nanomaterial substrate to deposit Au-Pt bimetallic nanoparticles. The unique structure of the PAAPNs sensor allows for low-potential operation (-1.0 V) with a wide monitoring range (-0.25 to 36 mM) in a neutral environment. Moreover, the sensor exhibited excellent selectivity (<10% response of interference) even without the use of an anti-interference outer membrane. Further investigation using density functional theory (DFT) simulation revealed the synergistic effect between Au and Pt in promoting glucose oxidation. Overall, this work provides a simple and low-carbon footprint method for creating carbon substrates from tissue paper for recycling, offering new opportunities for fabricating novel value-added nanomaterials for medical sensing applications. [ABSTRACT FROM AUTHOR]

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu3+ on paper and step-by-step grafting of CDs and Eu3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results. [ABSTRACT FROM AUTHOR]

A novel microfluidic paper-based analytical device with dual colorimetric and electrochemical detection (dual μPAD) was developed for the assessment of transferrin saturation (TSAT) in samples from ischemic stroke patients. TSAT was calculated from the ratio between transferrin-bound iron, which was colorimetrically measured, and the total iron-binding capacity, which was electrochemically measured. To this end, a μPAD was smartly designed, which integrated both colorimetric and electrochemical detection reservoirs, communicating via a microchannel acting as a chemical reactor, and with preloading/storing capabilities (reagent-free device). This approach allowed the dual and simultaneous determination of both parameters, providing an improvement in the reliability of the results due to an independent signal principle and processing. The μPADs were validated by analyzing a certified reference material, showing excellent accuracy (Er ≤ 5%) and precision (RSD ≤ 2%). Then they were applied to the analysis of diagnosed serum samples from ischemic stroke patients. The results were compared to those provided by a free-interference method (urea-PAGE). Impressively, both methods exhibited a good correlation (r = 0.96, p < 0.05) and no significant differences were found between them (slope 1.0 ± 0.1 and the intercept 1 ± 4, p < 0.05), demonstrating the excellent accuracy of our approach during the analysis of complex samples from ischemic stroke patients, using just 90 μL of clinical samples and taking less than 90 min in comparison with the 18 hours required by the urea-PAGE approach. The developed fully integrated colorimetric-electrochemical μPAD is a promising ready to use reagent-free device for the point-of-care testing of TSAT, which can be used to assist physicians in the fast diagnosis and prognosis of ischemic strokes, where the decision-time is crucial for the patient's survival. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

Here, a novel paired electrolysis system is constructed, where fluorine-doped tin oxide glass serves as the anode for the water oxidation reaction to produce hydrogen peroxide (H2O2), and cobalt phthalocyanine (CoPc)/carbon nanotube (CNT) loaded carbon paper as the cathode for CO2 reduction to generate CO. This system demonstrates a high overall energy efficiency of 34%, where a faradaic efficiency exceeding 90% for CO2 reduction and 60% for water oxidation to H2O2 have been achieved, demonstrating significant energy savings of nearly 40% compared to the respective half-reaction systems. [ABSTRACT FROM AUTHOR]

The exploration of high-performance hydrogen evolution reaction (HER) catalysts is conducive to the development of clean hydrogen energy, yet still remains a challenge. Herein, we rapidly synthesize the Mo2C/MoS2 heterostructure on carbon paper (Mo2C/MoS2–CP) via carbothermal shock in only two seconds. The construction of the Mo2C/MoS2 heterostructure regulates the electronic structure of the Mo site and facilitates charge transfer during the HER process. Moreover, the catalyst exhibits enhanced hydrophilicity and aerophobicity, facilitating optimal electrolyte–catalyst interaction and efficient hydrogen bubble detachment for accelerated mass transfer. Consequently, Mo2C/MoS2–CP exhibits superior intrinsic alkaline HER activity, and excellent stability for 100 h. This finding provides a novel insight into the development of outstanding HER catalysts. [ABSTRACT FROM AUTHOR]

Gossypol, a phytotoxicant in cotton-seed oil, has been found to sensitize Tb(III)-luminescence in a supramolecular hydrogel. Based on this observation, a paper-based sensor has been developed to detect gossypol with a limit of detection (LOD) of 2.9 nM. This is the first report of water-based detection with the highest sensitivity involving turn-on time-gated luminescence. This method was also able to sense gossypol in commercial crude cotton-seed oil. [ABSTRACT FROM AUTHOR]

The creation of MFC-active smart molecules by tuning functionality has received considerable attention owing to its versatile applicability. Pyrene-based twisted donor–acceptor (D–A) dyes (PySS and PySP) have been synthesized and characterized. Here, the pyrene is directly connected with thiophene, and this unit is further linked terminally to photoactive species (thiophene/pyridine) via a four-carbon unit conjugated spacer. These molecules show excellent solvatochromic properties, with a substantial shifting of the emission wavelength (PySS- 147 nm and PySP- 130 nm). The lowest transition state contains a significant contribution from ICT characteristics, as evidenced by spectral analysis and computational calculations. Moreover, these are identified as 'aggregation-induced enhanced emission' (AIEE) active compounds and exhibit mechanofluorochromism (MFC). By grinding, PySS and PySP display MFC features with 50 nm and 54 nm red shifting, respectively. Interestingly, PySS shows a gradual emission change from green (510 nm) to orange emission (578 nm) by gradually changing the pressure with a hydraulic press (0 to 12.5 tons). The single crystal structure of both compounds was investigated to understand the structure–property relationship for MFC. The crystal packing shows that the twisted molecules (dihedral angle between pyrene and thiophene is 59.36° and 56.93° for PySS and PySP, respectively) are loosely bound with several weak interactions (C–H⋯π, C–π⋯H, H⋯H, C–H⋯O). Interestingly, it was observed that two molecules in a unit cell are arranged in an antiparallel fashion; these molecular pairs are linearly connected to another pair axially, forming a long one-dimensional chain-type arrangement. On applying pressure, these twisted molecular pairs may slowly planarize, leading the molecules to come closer, thus changing the molecular interaction and the emission properties. A feasibility study of the potentiality of using these compounds in data encryption–decryption and security ink has also been demonstrated. [ABSTRACT FROM AUTHOR]

"Waste" is "wealth": the transformation of biomass waste into high value-added substances holds significant environmental and economic importance. In our work, orange peel was effectively transformed into valuable fluorescent carbon quantum dots (CQDs) by solvothermal treatment. The resultant CQDs displayed favorable dispersion and a mean particle size of 3.14 ± 0.71 nm. Moreover, these CQDs exhibited a characteristic excitation-dependent fluorescence behavior, which can produce the maximum emission wavelength at 506 nm with excitation at 400 nm. Upon the introduction of permanganate (MnO4−), the fluorescence intensity of CQDs diminished gradually caused by the inner filter effect (IFE) as well as the static quenching effect (SQE). The results revealed that the CQDs can serve as a fluorescent probe, which possessed high performance in terms of sensitivity for quantitative analysis of MnO4−, boasting a low detection limit of 3.31 μM. Subsequently, the application of this fluorescent probe in actual water samples was further explored, resulting in a recovery rate between 98.18% and 101.69%, with relative standard deviations (RSDs) ranging from 1.85% to 2.68%, which was highly satisfactory. The portable paper-based sensor, fabricated by depositing CQDs onto filter paper, is capable of quantitatively and visually detecting MnO4− in combination with a smartphone, thus providing a rapid on-site detection tool for MnO4−. As far as we know, this study provides the inaugural account of a smartphone-based portable sensor for visual determination of MnO4− by using biomass waste based CQDs, suggesting its immense potential for real-time monitoring applications. [ABSTRACT FROM AUTHOR]

We reported a colorimetric paper-based device by integrating the modified acid RNA-cleaving DNAzymes (MaRCD-EC1) for highly sensitive (detection limit = 102 CFU mL−1), and rapid (within 30 min) detection of E. coli without amplification. This device exhibited a clinical sensitivity of 100% and a specificity of 100% in identifying E. coli-associated urinary tract infections (UTIs) using the clinical urine samples. [ABSTRACT FROM AUTHOR]

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL−1, 2.7 μmol L−1, and 6.8 μmol L−1, respectively. A limit of detection of 0.048 fg mL−1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m−2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper. [ABSTRACT FROM AUTHOR]

Bacillus cereus is a foodborne opportunistic pathogen commonly found in humans and animals. It produces various toxins, causing frequent food safety incidents. Therefore, establishing a fast and accurate method for detecting B. cereus enterotoxin is crucial for disease diagnosis and food safety. In this study, Haemolysin BL comprising Hbl B and L2 was obtained from a prokaryotic expression system and then used to immunize mice for antibody preparation. Paired antibodies 2A10–5C7 against Hbl B and 1E2–10A4 against Hbl L2 were screened using the chessboard method and then used to construct a double-antibody sandwich detection method and a lateral flow immunochromatographic assay (LFIA) to quantify the concentrations of Hbl B and L2 in PBS and milk. The limits of detection for Hbl B and L2 in milk were 0.74 ng mL−1 and 1 ng mL−1 with detection ranges of 1.48–645.5 ng mL−1 and 2.33–391.5 ng mL−1. The spiked recoveries ranged from 82.2% to 105.67% and there was no cross-reactivity with common microbial toxins. The established LFIA was low in cost and rapid and was comparable with commercially available detection kits for food samples. [ABSTRACT FROM AUTHOR]

Paper-based analytical devices (PADs) are very convenient for determining biomarkers in point-of-care (POC) diagnosis while requiring sample pre-treatment or impurity separation. This study reports a novel hydrogel-coupled, paper-based analytical device (PAD) for separation-free H2O2 colorimetric detection in both aqueous solution and cell lysis with sample-to-answer analysis by directly loading into the sample test zone. By encapsulating an inorganic mimic enzyme and chromogenic substrate into the sodium alginate (SA) hydrogel, amplification of the color signal after catalyzing the substrate could be achieved. Taking advantage of the nanoscale porous structure of the hydrogel and the lateral flow channel of the PAD, large interference fragments or bio-macromolecules are prevented from diffusing into the chromogenic reaction, whereas the small target molecules enter the sensing region to trigger the catalytic reaction. This method demonstrated a rapid and accurate analysis with a limit of detection as low as 0.06 mM and detection selectivity. Our proposed device requires no enzyme and is separation-free, portable, easy-to-fabricate, and low-cost, and may offer a platform for quantitative or qualitative analysis of other analytes in body fluids for POC applications. [ABSTRACT FROM AUTHOR]

This study introduces the development of a photothermal-based microfluidic paper analytical device (PT-µPAD) integrated with near-field communication (NFC) technology and smartphone readout for enzyme-free glucose quantification in human samples. With the properties of gold nanoparticles (AuNPs) both as a nanozyme and as a photothermal substrate, there is no need for costly reagents like enzymes or a readout instrumentation for the selective and sensitive detection of glucose. In PT-µPADs, AuNPs are etched by hydrogen peroxide (H2O2) generated from glucose catalysis. Photothermal detection from the plasmonic heating of these AuNPs when illuminated by a 533nm LED light source is achieved by inserting the PT-µPAD sensor into a portable NFC platform suitable for smartphone readout. Temperature variation is directly proportional to the glucose concentration. After optimization, we acquired a linear range between 5.0 and 20.0 µmol L−1 (R2 = 0.9967) and a limit of detection (LOD) of 25.0 nmol L−1 for glucose. Additionally, while our sensor does not utilize any enzyme, it is remarkably selective to glucose with no effects from interferences. Recovery studies in various human control samples indicated a range of 99.73–102.66% with the highest RSD of 3.53%, making it highly accurate and precise. Moreover, our method is more sensitive than other methods relying on conventional µPADs for glucose sensing. By integrating the potential benefits of microfluidics, nanomaterials as nanozymes, and NFC technology for wireless readout, our sensor demonstrates great promise as an accessible, affordable, and shelf-stable device for glucose quantification. Moreover, this concept can be extended to detect other molecules of interest as a point-of-care (POC) diagnostics device. [ABSTRACT FROM AUTHOR]

Nowadays, kidney dysfunction is a common health issue due to the modernized lifestyle. Even though medications are commercially available to treat kidney diseases, early diagnosis is crucial and challenging. Clinically, measuring urine creatinine and pH has gained significant interest as a way to diagnose kidney diseases early. In the present work, we attempted to develop a low-cost, robust, accurate and naked-eye colorimetric method to determine both creatinine levels and pH variations in artificial urine samples using a simple 3D-printed hybrid microfluidic device. Creatinine was detected by the incorporation of the traditional Jaffe test onto the hybrid paper–PMMA microfluidic device and pH (4–8) was measured by a simple anthocyanin test. Notably, the tests were established without employing any sophisticated or costly instrument clusters. The developed 3D-printed microfluidic probe showed a limit of detection (LOD) of 0.04 mM for creatinine over a concentration range of 1–10 mM, with a regression coefficient (R2) of 0.995 in laboratory conditions. Interestingly, the experimental data obtained with artificial urine exhibited a wide linear range from 0.1 mM to 5 mM under different pH values ranging from 4 to 8 in the presence of matrices commonly found in urine samples other than proteins, indicating the potential use of this method in pre-clinical analysis. Since the wide linear range of urine creatinine in artificial urine samples falls well below the clinically relevant concentrations in humans (0.07–0.27 mM), the developed lab-on-chip device is further suitable for clinical evaluation with proper ethical clearance. This 3D-printed hybrid microfluidic colorimetry-based creatinine detection and pH indicator platform can be beneficial in the healthcare sector due to the on-site testing capability, cost-effectiveness, ease of use, robustness, and instrument-free approach. [ABSTRACT FROM AUTHOR]

Metal halide perovskite quantum dots (QDs) with unique physicochemical properties are promising candidates for next-generation optoelectronics, but they often suffer from stability issues that severely limit their potential for practical applications. In this work, we adopt an oleic acid/oleylamine-free approach to synthesize MAPbBr3 quantum dot (MQD) papers by incorporating MQDs into cellulose nanofiber frameworks. The abundant long-chain binding ligands containing sulfate terminal groups within the cellulose nanofiber remarkably stabilize the MQD structure, enabling the fabrication of self-power and flexible MQD paper photodetectors with a responsivity of ∼0.19 mA W−1, detectivity of 1.58 × 108 cm Hz1/2 W−1, and excellent bendability and reliability after 500 bending cycles. More importantly, these MQD/cellulose-based self-powered photodetectors demonstrate extraordinarily high environmental stability, maintaining more than 90% of the initial responsivity after 60 days. The simple disposability of the paper-based device is also illustrated by burning within one second, suggesting the ease of device elimination. Our work provides a unique approach to designing ultra-stable perovskite QD-based electronics with unprecedented functionalities. [ABSTRACT FROM AUTHOR]

In this work, we report on five novel coordination polymers (CPs) based on the linkage of the [Cd(6apic)2] building block [where 6apic = 6-aminopicolinate] by different bipyridine-type organic spacers, forming different coordination compounds with the following formulae: [Cd(μ-6apic)2]n (1), {[Cd(6apic)2(μ-bipy)]·H2O}n (2), {[Cd(6apic)2(μ-bpe)]·2H2O}n (3), [Cd(6apic)(μ-6apic)(μ-bpa)0.5]n (4) and {[Cd2(6apic)4(μ-tmbp)]·7H2O}n (5) [where bipy = 4,4′-bipyridine, bpe = 1,2-di(4-pyridyl)ethylene, bpa = 1,2-di(4-pyridyl)ethane (bpa) and tmbp = 1,3-di(4-pyridyl)propane]. Most of the synthesized compounds form infinite metal–organic rods through the linkage of the building block by the bipyridine-type linker, except in the case of compound 4 whose assembly forms a densely packed 3D architecture. All compounds were fully characterized and their photoluminescence properties were studied experimentally and computationally through density functional theory (DFT) calculations. All compounds display, upon UV excitation, a similar blue emission of variable intensity depending on the linker employed for the connection of the building units, among which compound 2 deserves to be highlighted for its room temperature phosphorescence (RTP) with an emission lifetime of 32 ms that extends to 79 ms at low temperature. These good photoluminescence properties, in addition to its stability in water over a wide pH range (between 2 and 10), motivated us to study compound 2 as a sensor for the detection of metal ions in water, and it showed high sensitivity to Fe3+ through a fluorescence turn-off mechanism and an unspecific turn-on response to Zn2+. Furthermore, the compound is processed as a paper-based analytical device (PAD) in which the phosphorescence emission is preserved, improving the sensing capacity toward Fe3+ ions. [ABSTRACT FROM AUTHOR]