Search

The trade e off between protection and weight is a constant consideration when designing a portable protective solution. Greater mobility is a desirable attribute and protection must therefore adapt, prompting a demand for lightweight, simple to construct, low-cost and effective ballistic protection systems. High strength and ductility, wave spreading capability and good energy absorption are key properties for ballistic protection. Four materials, polycarbonate, Kevlar®-epoxy, polyurethane foam, and aluminium alloy, possess these properties and were selected for analysis by numerical simulation. Multilayered configurations were proven to be an optimal solution, by exploiting the advantages of each material without having large penalties of mass and cost. Numerical modelling using ANSYS AUTODYN® is used to simulate monolithic and multi-layered target configurations, to obtain the penetration mitigation performance. The results are analysed to select configurations based on different requirements, such as lowest cost, lowest mass, best performance, and optimal configuration which balanced the three key parameters mentioned. The optimal configuration of Aluminium, Kevlar-Epoxy, Polyurethane, and Polycarbonate has layers with thickness of 7, 3, 38, 2 mm respectively with a total mass of 7.97 kg, total cost of $39.86 and penetration of 29.34% (14.67 mm). Polynomial relationships between performance and mass/cost are also determined. [ABSTRACT FROM AUTHOR]

In the era of unmanned war, with the increasing muzzle velocity requirement, the design of gun is significantly restricted by recoil, especially for guns installed on unmanned aerial vehicles. A recoilless gun with combustible cartridge was designed to eliminate recoil and increase projectile velocity, and the influence of main parameters on recoil was studied. First, a design of a recoilless gun with high projectile velocity is proposed based on combustible cartridge case. Next, a classical interior ballistic model is developed during the recoilless gun firing cycle, and the effect of main parameters of interior ballistics on the performance is investigated. Additionally, simple nonlinear fitting formulae are defined to highlight the variation of recoil momentum with the time of interior ballistic model. Finally, numerical simulation results are compared with the test results to validate the feasibility of the design. The experimental results demonstrate that the classical interior ballistic model can be used to accurately analyze the effect of the parameters on the projectile velocity and the recoil reduction efficiency. The projectile velocity of the recoilless gun could raised to 1200 m/s and the recoil momentum could be eliminated almostly. Therefore, the newly designed recoilless gun effectively eliminates the recoil momentum and significantly improves the projectile velocity. The findings should make an important contribution to the field of engineering applications of recoilless gun. [ABSTRACT FROM AUTHOR]

To clarify the combustion process of a modular charge system with a primer gap, the rules governing the cartridge movement and pressure change in the chamber are analyzed. Based on the characteristics of the modular charge system, an axisymmetric two-phase flow model of the interior ballistics is established, with the monotonic upward-centered scheme for conservation laws adopted to calculate the combustion process. Compared with the experimental results, the difference in the peak pressure is less than 5%, which indicates that the mathematical model and scheme are reliable and accurate. The results show that, during the initial stage of ignition, the combustible container remains unbroken, and the gas and solid particles are prevented from spreading to the chamber by the end cap of the cartridge. Thus, only the gas inside the igniter tube influences the flow field in the chamber. After the combustible container has broken, the gas and solid particles move rapidly toward the cavity from the combustible container. The axial movement of solid particles is more intense than that of the gas particles, but the radial movement of solid particles is relatively weak. Furthermore, the existence of the primer gap leads to a delay in the ignition time of the solid particles, which delays the rupture time of the igniter tube and the module cartridge. [ABSTRACT FROM AUTHOR]

The change of ambient temperature will cause the change of gunpowder burning rate, which will directly affect the ballistic performance of the projectile and cause the change of the overload of the projectile fuze system. In this study, the numerical simulation program of the interior trajectory of a large-caliber gun was established by MATLAB, and the variation rules of the corresponding trajectory parameters at different temperatures were obtained. ANSYS finite element software is used to analyze the force of the projectile fuze system under different ambient temperatures. The results show that under the same loading conditions, with the increase of ambient temperature, the maximum pressure in the gun bore and the muzzle velocity of the projectile increase significantly, and the stress and strain of the projectile fuze system in the bore increase gradually. The numerical simulation results are in good agreement with the theory, which reveals the influence of ambient temperature on the overload in the bore of the projectile fuze system to a certain extent, and provides theoretical support for the study of internal ballistics, charge design and gun use. [ABSTRACT FROM AUTHOR]

Researchers use a variety of target materials, and sometimes combinations of materials, in their archaeological experiments to examine thrust‐spear or projectile penetration, impact angle, durability, and other issues involving prehistoric hunting weaponry. This variety of target materials is beneficial to archaeological science in several ways, but it may also hinder the comparison of results because many of these target materials do not necessarily share similar physical properties. Here, we assess the penetration properties of four different target materials—store‐bought meat, clay, and two types of gelatin—via static penetration tests of a modern broadhead‐tipped arrow and a stone‐tipped projectile attached to an Instron Universal Materials Tester. Our analyses of load‐deflection curves, peak load, and work energy demonstrate how the four target materials are similar in some ways but different in others, which suggests that researchers may strategically employ one or several depending on the question asked or hypothesis tested. [ABSTRACT FROM AUTHOR]

Empirical assessment of cetacean welfare to inform stranding interventions is lacking. Here, potential welfare indicators are described for two stranded pygmy killer whales (Feresa attenuata), along with euthanasia procedures and pathology of potential relevance. The animals were filmed for 3.5 and 1.5 hr, respectively, allowing assessment of 19 indicators, including animal behaviors and human interventions. Eight interventions and 19 animal behaviors were identified; 17 and 11 behaviors were displayed by animal 1 and 2, respectively. Examination of ballistics euthanasia revealed atypical projectile placement and characterized animal behavioral responses, but welfare implications could not be assessed as insensibility was not verified in-field. Pulmonary edema and renal degeneration were documented in both animals; differential etiologies include ischemia-reperfusion, shock, and/or myopathy. Potential relationships among histopathology and welfare indicators are explored to infer affective experiences. For example, simultaneous head-lifting with respiration increased over time which, alongside pulmonary edema, suggests these animals experienced breathlessness. Other likely affective states include fatigue and discomfort; there are insufficient data to estimate the intensity or duration of these experiences or to provide an overall welfare grade/score. Further data are required to validate the proposed welfare indicators and to progress development of holistic approaches to welfare assessment at cetacean strandings. [ABSTRACT FROM AUTHOR]

The presented work discusses performing a V/L (Vulnerability/Lethality) analysis on an armored tank based on an RHA (Rolled Aomogeneous Armour) equivalence. It is shown how the approach works using small examples verified with hand calculations. Other more complex examples include a set of welded plates protecting a HYBRID III 50 Percentile Male ATD (Anthropomorphic Test Device). Considered response parameters are the VAA (Vulnerable Area Assessment) damage maps, expected protection capability plot, and damage area fractions. Furthermore, different V/L analyses of the Russian T-80 tank are displayed. It is illustrated how to apply the concept of explicit finite element models to find the critical RHA equivalent armor thickness at normal impact. It is done with terminal ballistic models for three materials: RHA, Aluminum 5083-H116, and Armox 500T. [ABSTRACT FROM AUTHOR]

Interior ballistics modelling intends to calculate physical quantities by solving equations requiring a set of input like thermodynamical properties linked to propellant or mechanical properties like friction coefficients, linked to the system, that are often difficult to assess experimentally. Using a consequent and high‐quality dataset of thousands of 155 mm modular charge experiments, we investigated how deep and machine learning approaches could build an efficient model for predicting muzzle velocity, pressure, and ignition time. After identifying the main variables influencing the physics and several potentially relevant to the machine learning and deep learning algorithms, a stacking ensemble learning model (SEL) was built. It is composed of eight machine learning algorithms and one deep learning algorithm, all as weak learner, reaching a consensus for predicting experimental outputs through a strong learner. The performance assessment, on a 900 experiments test data set that were not used in training, shows a prediction accuracy of 97 % at 1 % accuracy for muzzle velocity, 93 % at 3 % for pressure and 72 % at 5 ms for ignition time. The prediction ability for muzzle velocity within 2 m/s reaches 73 % that can be considered as sufficient. Furthermore, the SEL model even having zero knowledge about physics can discriminate gun barrel erosion effect at high and low pressure. This approach allows to imagine a way of modelling physical phenomena poorly described by physical equations or requiring unmeasurable figures. [ABSTRACT FROM AUTHOR]

A recently published modeling approach for the penetration into adobe and previous approaches implicitly criticized are reviewed and discussed. This article contains a note on the paper titled "Ballistic model for the prediction of penetration depth and residual velocity in adobe: A new interpretation of the ballistic resistance of earthen masonry" (DOI: https://doi.org/10.1016/j.dt.2018.07.017). Reply to the Note from Li Piani et al is linked to this article. [ABSTRACT FROM AUTHOR]

It is shown that the ratio of the proton convective gyroradius r Ep, to the width of the shock ramp D , controls the thermalization process of ions in quasi-perpendicular shocks. When r Ep/ D > 1, the solar wind beam energy is rapidly converted to gyration (thermal) energy by a universal, transit time thermalization (TTT) mechanism that does not require any collisions, waves, or instabilities. The TTT of ions on magnetic field gradients is followed by stochastic wave energization (SWE) on electric field gradients. Ions heated by TTT and SWE processes are subject to additional ballistic surfing acceleration caused by the convection field in the shock front. These three fundamental ion energization mechanisms are studied with test-particle simulations in a realistic shock model, and are shown to be consistent with magnetospheric multiscale measurements in the Earth's bow shock. It is also shown that shock reflected ions are produced by the SWE process and not by the cross-shock potential. An explanation for downstream oscillations in quasi-perpendicular shocks is also provided. [ABSTRACT FROM AUTHOR]

The ballistic impact response of Kevlar textiles is significantly influenced by the friction between the yarns. It increases the dissipation of energy when yarns begin to displace relative to one another and it also results in to transfer of load to a larger area during ballistic impacts. In the present work, a novel sulfonyl aryl group containing monomer acrylic acid-2-(toluene sulphonyl amine)-ethyl ester (AATSAEE) was synthesized by a three-step process with ethanol amine and p-toluene sulfonic acid as starting material. The monomer was homopolymerized and grafted on Kevlar fabric by UV-induced free radical polymerization technique. Benzoyl peroxide (BPO) was used as initiator. Utilizing spectroscopic and thermal gravimetric methods, the monomer, precursor, and the homopolymer were characterized. The yarn pull-out tests on unmodified and AATSAEE grafted Kevlar fabrics were performed on Universal Tensile Tester at a steady speed of the upper jaw of 50 cm min−1. Increases in yarn pull out force have been noted with grafting of AATSAEE on Kevlar fabric. The peak force increases around 284% with grafting which indicates an increase in friction forces. When these yarns start to move apart from one another due to friction factors, the fabric's energy dissipation increases and it may results in to increase in energy absorption at the time of ballistic impacts. [ABSTRACT FROM AUTHOR]

Featured Application: These research results can be applied in forest fire suppression. This paper focuses on improving fire suppression performance through the use of compressed-air launching technology. A launch dynamics calculation model of a compressed-air launcher is presented, developed using VC++ programming, to simulate the acceleration process of a fire-extinguishing bomb in a barrel. By analyzing the influences of various structural and initial parameters on interior ballistics variations, the effectiveness of the calculation model and program in accurately simulating the launching process is demonstrated. The calculation results indicate that the bore pressure follows a similar trend to that of traditional gunpowder launching. Additionally, it is found that specific structural parameters, such as nozzle diameter and gas cylinder volume, have a direct impact on interior ballistics variations. Notably, the nozzle diameter positively affects the peak pressure, muzzle velocity, gas transfer efficiency, and launch efficiency. To ensure an optimal launch effect and efficiency, the nozzle diameter should be selected to be more than half of the launcher caliber. Similarly, the gas cylinder volume positively influences the peak pressure and muzzle velocity while negatively affecting the gas transfer efficiency and launch efficiency. Furthermore, the initial pressure in the gas cylinder exhibits a positive linear relationship with both the peak pressure and muzzle velocity but a negative linear relationship with the gas transfer efficiency and launch efficiency. The loading position minimally impacts the peak pressure and muzzle velocity but slightly enhances the gas transfer efficiency and launch efficiency. Finally, it is observed that launch angles do not affect the interior ballistic process. The research findings provide valuable theoretical guidance for determining the working parameters of compressed-air accelerated fire-extinguishing bombs. [ABSTRACT FROM AUTHOR]

Two-phase flow numerical methods are applied in internal ballistics widely, which has made higher fidelity analysis with minimal cost become an urgent demand. Current methods are based on independent dimension, and there is no definite conversion criterion and data transmission method, which have limited the application of efficient hybrid models applied to calculation. In this paper, we propose a hybrid method by linking a two dimensional (2D) model to a one dimensional (1D) model for two-phase flow. First, 1D and 2D two-phase flow models are established according to the flow field states in different phases. Next, the criterion of conversion between the two models is established, which is a quantitative index to judge the degree of radial effect and axial effect. Finally, dimension transformation in the radial direction and grid mergence in the axial direction are conducted to complete the whole computing model. The simulation results show that the hybrid method is more efficient in the interior ballistic process and maintains the level of trust in classical codes. Compared with the 2D method, the hybrid method significantly improves the computational efficiency by 86.5%. By analyzing the state in the chamber, the accuracy of the conversion criterion is confirmed. This criterion can be used as the transformation criterion of the hybrid model to form the standard multi-dimensional calculation transformation criterion of interior ballistics and may be promising for the rapid simulation of two-phase flow in interior ballistics. [ABSTRACT FROM AUTHOR]

Multi-layer fabrics are commonly used in ballistics shields with a lower bulletproof class to protect against pistol and revolver bullets. In order to additionally limit the dynamic deflection of the samples, layers reinforced with additional materials, including non-Newtonian fluids compacted by shear, are additionally used. Performing a wide range of tests in each case can be very problematic; therefore, there are many calculation methods that allow, with better or worse results, mapping of the behavior of the material in the case of impact loads. The search for simplified methods is very important in order to simplify the complexity of numerical fabric models while maintaining the accuracy of the results obtained. In this article, multi-layer composites were tested. Two samples were included in the elements subjected to shelling. In the first sample, the outer layers consisted of aramid fabrics in a laminate with a thermoplastic polymer matrix. The middle layer contained a non-Newtonian shear-thickening fluid enclosed in hexagonal (honeycomb) cells. The fluid was produced using polypropylene glycol and colloidal silica powder with a diameter of 14 µm in the proportions of 60/40. The backing plate was made using a 12-layer composite made of Twaron® para-aramid fabrics with a DCPD matrix—not yet used in a wide range of ballistics. Then, numerical simulations were carried out in the Abaqus/Explicit dynamic analysis. The Johnson–Cook constitutive strength model was used to describe the behavior of elastic–plastic materials constituting the elements of the projectiles. For the non-Newtonian fluid, a Up-Us EOS was used. The inner layers of the fabric were treated as an orthotropic material. Complete homogenization of the sample layers was carried out, thanks to which each layer was treated as a homogeneous continuum. As a parameter of fracture mechanics for shield components, the strain criterion was used with the smooth particles hydrodynamics method (SPH). Then, the results of simulations were compared with the results of the ballistic test for both samples placed next to each other, which resulted in the formation of a multi-layer composite in one ballistic test subjected to impact loads during firing with a 9 × 19 mm Parabellum FMJ projectile with an initial velocity of 370 ± 10 m/s. The results of numerical tests are very similar to the ballistic tests, which indicates the correct mapping of the process and the correct conduct of layer homogenization. The applied proportions of the components in the non-Newtonian fluid allowed a reduction in the deflection compared to previous studies. Additionally, the proposal to use a DCPD matrix allowed to obtain a much lower deflection value compared to other materials, which is a novelty in the field of production of ballistic shields. [ABSTRACT FROM AUTHOR]

To date, various designs have been proposed to increase the efficiency of radiative coolers with approaches such as changes in materials and their properties, size and shape of the elements, and structures geometry. In the present work, an attempt has been made to obtain this important issue by presenting an innovative strategy from a new perspective. In this strategy, by keeping the face exposed to solar energy away from the body, heat distribution can be inhibited, which leads to a decrease in body temperature. This act simultaneously provides a higher operating temperature for the emitter section, thereby enhancing the exergy of the system. On the other hand, the presence of the thermal diode allows the surface of the object to continue to radiate its heat. Hence, several experiments were designed and performed to evaluate the performance of the strategy by an experimental apparatus built for this purpose. Initially, the rectification ratio results of constructed rectifier mirrors showed that the light transmission amount in the forward path is nearly 44% higher than in the reverse direction. In the next step, the temperature measurement of the samples showed the sub-ambient temperature for the present work with a difference of 9 and 2 °C, against direct sunlight and the night sky, respectively. This model also has a high-temperature difference of about 13, 11, and 6.5 °C during the day and 1.6, 0.5, and 0.5 °C at night below the other three samples. This superiority was maintained in cloudy weather conditions as well as thermal shock stability. One of the most important applications of radiation coolers is in the aerospace industry. In this particular application, in addition to cooling, it is vital to protect the equipment against thermal shock caused by sudden and extreme temperature differences in space. Due to obtaining results such as efficient cooling rate, and high resistance to thermal shock, this concept provides a practical vision for improving the spacecraft's cooling systems. [ABSTRACT FROM AUTHOR]

Superior ballistic performance and the lightweight character of Ti alloys are considered as main reasons for their use in armour applications against a broad spectrum of ballistic threats, e.g. bullet, fragment or blast impact. Because dynamic loading caused by typical penetrators is characterized by high strain rates, only specific test methods allow a closer investigation of the respective material behaviour. In the present study, quasi-static and dynamic compression tests as well as ballistic tests were conducted on a twophase α+β alloy Ti-6Al-4V (in m%) manufactured by hot-rolling. Post-deformation heat treatments, influencing microstructure and mechanical properties were applied in order to compare three different microstructural configurations: as-rolled, mill-annealed and bimodal. While, on the one hand, ballistic tests were employed for the determination of the ballistic limit velocity v50, compression tests, on the other hand, delivered essential input parameters for the application of the Johnson-Cook constitutive model in a finite element simulation of the impact event. The comparison of experimental results to simulation results was supplemented by means of microstructural characterization of tested samples with the focus set on the prevalently observed deformation and damage mechanisms, as for example adiabatic shearing. [ABSTRACT FROM AUTHOR]

Hybrid composite materials combine different fibers in preform and take advantages of different mechanical behaviors for improving ballistic impact damage tolerances. Here we report ballistic impact damages of plain-woven laminates with different hybrids and stacking sequences. Three kinds of hybrid laminates, i.e., carbon/Kevlar, carbon/ultra-high molecular weight polyethylene (UHMWPE), and UHMWPE/Kevlar, had been prepared and tested in ballistic penetration with fragment simulating projectiles (FSP). The residual velocities of the projectiles and impact damage morphologies of the laminates have been obtained to show impact energy absorptions for the different hybrid schemes. A microstructural model of the hybrid laminates had also been established to show impact damage mechanisms with finite element analysis (FEA). We found that the UHMWPE/Kevlar hybrid laminates with Kevlar layers as the front face have the highest energy absorption capacity, followed by the carbon/Kevlar hybrid laminates with carbon layers as the front face. The main damage modes are fiber breakages, matrix crack and interlayer delamination. The ballistic damage evolutions from the FEA results show that the major damage is shear failure for front layers, while tension failure for the back layers. We expect that the ballistic impact performance could be improved from the different hybrid schemes. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Ordnance Equipment Engineering is the property of Chongqing University of Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The Novalis Tx Linear Accelerator is among the machines dedicated to radiosurgery that allow stereotactic radiotherapy based on Dynamic Conformal Arc Therapy (DCAT) or Volumetric Modulated Arc Treatment (VMAT), which are the conventional methods for treating brain metastases. Nevertheless, VMAT may reduce early or late complication probability by providing highly conformal dose distributions, increasing target volume coverage, and sparing normal tissues. A further enhancement of the conformation and dose gradient may be one of the possible benefits of the addition of non-coplanar arcs. The purpose of this article is to compare and analyse VMAT, DCAT, and VMAT with Non-Coplanar Arcs (NcVMAT). DCAT, CoVMAT, and NcVMAT modalities were created for 15 patients. Target conformal dose, target coverage, and normal brain tissue dose were evaluated among the three modalities. The NcVMAT modality greatly outperformed the others in terms of both conformal indices (RTOG-CI and IP-CI) and the dose gradient index. Dose comparisons to normal brain tissue revealed that the doses received by the healthy brain were significantly lower in the NcVMAT plans. The MUs of the DCAT and NcVMAT plans were larger than those of the CoVMAT plans. The NcVMAT modality dramatically increases the target conformal dose and gives a lower dose to normal brain tissue compared to the CoVMAT and DCAT modalities. [ABSTRACT FROM AUTHOR]

A promising direction in barrel ballistics aimed at increasing the muzzle velocity of a projectile is the use of new propellants as an attached charge. This paper presents an experimental and theoretical method for determining the law of propellant combustion in a manometric experiment (in a closed volume). Within the framework of this method, a small number of experiments could be sufficient to determine a change in the law of combustion during the propellant burnout and depending on pressure. This method is demonstrated on the example of processing three experiments with model high-density propellant. The laws of combustion of high-density propellants, obtained in this study, can later be used to calculate the gas-dynamic parameters of a shot from a barrel system or a nozzle bomb (in a semi-closed volume) using these propellants. [ABSTRACT FROM AUTHOR]

The identification of firearms is of paramount importance for investigating crimes involving firearms, as it establishes the link between a particular firearm and firearm-related elements found at a crime scene, such as projectiles and cartridge cases. This identification relies on the visual comparison of such elements against reference samples from suspect firearms or those existing in databases. Whenever this approach is not possible, the chemical analysis of the gunpowder and gunshot residue can provide additional information that may assist in establishing a link between samples retrieved at a crime scene and those from a suspect or in the identification of the corresponding model and manufacturer of the ammunition used. The most commonly used method for the chemical analysis of gunshot residue is scanning electron microscopy with energy dispersive X-ray, which focuses on the inorganic elements present in ammunition formulation, particularly heavy metals. However, a change in the legal paradigm is pushing changes in these formulations to remove heavy metals due to their potential for environmental contamination and the health hazards they represent. For this reason, the importance of the analysis of organic compounds is leading to the adoption of a different set of analytical methodologies, mostly based on spectroscopy and chromatography. This manuscript reviews the constitution of primer and gunpowder formulations and the analytical methods currently used for detecting, characterising, and identifying their compounds. In addition, this contribution also explores how the information provided by these methodologies can be used in ammunition identification and how it is driving the development of novel applications within forensic ballistics. [ABSTRACT FROM AUTHOR]

An excellent flame suppression effect can be achieved using a novel porous brake. To understand the flame-suppression mechanism of a porous brake, combustion using a muzzle brake is investigated. A set of internal ballistic equations is employed to provide accurate velocity and pressure for a projectile moving to the muzzle. The multispecies transport Navier–Stokes equations, which incorporate complex chemical reactions, are solved by coupling a real gas equation of state, the Soave–Redlich–Kwong model, and a detailed chemical reaction kinetic model. The development of muzzle flow with a chemical reaction is simulated, and the interaction between chemical reactions with the muzzle flow field is numerically calculated to explain the muzzle combustion mechanism with a porous brake. The underlying mechanism is analyzed in detail. The results demonstrate that, first, the gas is fully expanded in the brake, leading to a reduction in pressure and temperature at the muzzle, thereby reducing the initial flame. In addition, the shock wave weakens due to the expansion and separation process, leading to a reduction in the mixture of gas and air, ultimately resulting in a reduction in the intermediate and secondary flames. [ABSTRACT FROM AUTHOR]

In the frame of an experimental setting, the formation of round-shaped compounded glass fragments on the exit site after gunshots through a windshield was examined. For that purpose, a 9 × 19 mm pistol (HK P30) and two different cartridges containing (a) a full metal jacketed round-nosed projectile and (b) a deformation projectile were used. On the basis of 52 gunshots, the morphology, impact angles and terminal ballistics of occurring compounded glass fragments were examined. The results showed that the compounded glass fragments' morphology allowed for the differentiation of two used projectiles. Fragments were able to cause round-shaped defects in a single cotton layer (T-shirt) with subsequent penetration of up to 2.4 cm into ballistic gelatin (10%, 4 °C). As a function of the projectile type, the compounded glass fragments showed different reproducible impact angles that differed notably from the known conical pattern of expelled glass fragments after bullet penetration. These findings might help to explain the atypical morphology of gunshot wounds with laminated glass as an intermediate target and prevent possible misinterpretations when reconstructing the sequence of events. [ABSTRACT FROM AUTHOR]

Sequential analysis concerns statistical evaluation in which the number, pattern, or composition of the data is not determined at the start of the investigation, but instead depends on the information acquired during the investigation. Although sequential analysis originated in ballistics testing for the Department of Defense (DoD)and it is widely used in other disciplines, it is underutilized in the DoD. Expanding the use of sequential analysis may save money and reduce test time. In this paper, we introduce sequential analysis, describe its current and potential uses in operational test and evaluation (OT&E), and present a method for applying it to the test and evaluation of defense systems. We evaluate the proposed method by performing simulation studies and applying the method to a case study. Additionally, we discuss challenges to address for sequential analysis in OT&E. Lastly, while operational testing is the focus in this paper, the methodology presented is applicable to campaigns of experimentation and general testing across numerous disciplines. [ABSTRACT FROM AUTHOR]

This article deals with Ballistic interpretation of gunshot traces by presenting the main theoretical and practical aspects, which are related to forensic ballistics, firearms, traces left by them and some elements of forensic tactics and technique. [ABSTRACT FROM AUTHOR]

A letter published in the Journal of Translational Medicine discusses the immune response triggered by radiation therapy (RT). The letter explains that RT can have both immunomodulatory and immunosuppressive effects on the immune system. The authors conducted a study comparing two types of RT, shield RT (SRT) and conformal RT (CRT), and found that CRT was more effective at delaying tumor growth and improving survival due to a stronger CD8+ TIL-mediated immune response. The study also revealed that monocytes played a critical role in activating CD8+ TILs after CRT. The authors emphasize the importance of accurately describing the irradiation technique used in preclinical studies and highlight the need for further research on the immune mechanisms underlying RT efficacy. [Extracted from the article]

To improve the tactical and technical performance of pulse correction projectiles while maintaining stability in uncertain conditions and considering practical engineering constraints, this study performs a multi-objective robust optimization design of the aerodynamic shape and external ballistics of a projectile. The study utilizes an aerodynamic force engineering algorithm and numerical trajectory calculations to obtain the projectile's performance responses within the Latin hypercube design space. To enhance optimization efficiency, a stochastic Kriging surrogate model is established to capture the inherent uncertainty of limited input data. Ultimately, a Pareto optimal solution for the projectile is obtained using a non-dominated sorting multi-objective sparrow search algorithm. The results of this study demonstrate that the consideration of design uncertainty in the robust optimization of pulse correction projectiles leads to significant enhancements in both lateral correction ability and range while satisfying flight stability requirements. Moreover, when compared to deterministic optimization, the performance variability of the design is markedly improved. This research methodology provides valuable insights for optimizing the performance of pulse correction projectiles. [ABSTRACT FROM AUTHOR]

A crime scene can provide valuable evidence critical to explain reason and modality of the occurred crime, and it can also lead to the arrest of criminals. The type of evidence collected by crime scene investigators or by law enforcement may accordingly effective involved cases. Bullets and cartridge cases examination is of paramount importance in forensic science because they may contain traces of microscopic striations, impressions and markings, which are unique and reproducible as "ballistic fingerprints". The analysis of bullets and cartridge cases is a complicated and challenging process, typically based on optical comparison, leading to the identification of the employed firearm. New methods have recently been proposed for more accurate comparisons, which rely on three-dimensionally reconstructed data. This paper aims at further advancing recent methods by introducing a novel immersive technique for ballistics comparison by means of Virtual Reality. Users can three-dimensionally examine the cartridge cases shapes through intuitive natural gestures, from any vantage viewpoint (including internal iper-magnified views), while having at their disposal sets of visual aids which could not be easily implemented in desktop-based applications. A user study was conducted to assess viability and performance of our solution, which involved fourteen individuals acquainted with the standard procedures used by law enforcement agencies. Results clearly indicated that our approach lead to faster adaptation of users to the UI/UX and more accurate and explainable ballistics examination results. [ABSTRACT FROM AUTHOR]

Shear thickening fluid (STF) is a dense colloidal suspension of nanoparticles in a carrier fluid in which the viscosity increases dramatically with a rise in shear rate. Due to the excellent energy absorption and energy dissipation of STF, there is a desire to employ STFs in a variety of impact applications. In this study, a comprehensive review on STFs' applications is presented. First, several common shear thickening mechanisms are discussed in this paper. The applications of different STF impregnated fabric composites and the STF's contributions on improving the impact, ballistic and stab resistance performance have also been presented. Moreover, recent developments of STF's applications, including dampers and shock absorbers, are included in this review. In addition, some novel applications (acoustic structure, STF-TENG and electrospun nonwoven mats) based on STF are summarized, to suggest the challenges of future research and propose some more deterministic research directions, e.g., potential trends for applications of STF. [ABSTRACT FROM AUTHOR]

An interval optimization method considering tolerance design is proposed to solve the uncertainty optimization problem of interior ballistics of cased telescoped ammunition. Firstly, the interval optimization model of the interior ballistics of the cased telescoped ammunition considering tolerance design is constructed. The interval optimization model of the interior ballistics of the cased telescoped ammunition considering tolerance design under uncertainty is presented. Then, considering the extremely low computational efficiency of the interval uncertain optimization, the back propagation neural network surrogate model is introduced. A series of pareto optimal solution is obtained by using non‐dominated sorting genetic algorithm II. Through the given design scheme, it provides a reference for the optimization of the interior ballistic performance of the cased telescoped ammunition under uncertain condition. [ABSTRACT FROM AUTHOR]

The high recoil force of a high-power gun produces a strong impact on the carrier, which severely limits the application of the high-power gun mounted on vehicles. A gas-controlled side-jet gun was designed to reduce the recoil force, and the gas-solid transient flow in the bifurcated tube of the gun was studied. First, a one-dimensional two-phase interior ballistics model was established considering the gas-solid coupling between the propellant gas and the valve in the front gas tube. Then, the propagation of the rarefaction wave in the barrel was studied, and the flow field distribution in the bifurcated tube was obtained. Finally, the mechanism of recoil reduction was analyzed. Results show that the bifurcated two-phase flow model can be used to accurately analyze the effect of the gas-controlled side-jet gun's parameters on the projectile velocity and the recoil reduction efficiency. The projectile velocities of the gas-controlled side-jet gun and the traditional gun are 955.7 m/s and 960 m/s, respectively. The projectile velocity loss of the gas-controlled side-jet gun is less than 0.5 %. The recoil momentum of the traditional gun and the gas-controlled side-jet gun are 538.62 N·s and 336.68 N·s, respectively. The recoil momentum of the gas-controlled side-jet gun decreases by 37.49 %. Additionally, the single firing time of the gas-controlled side-jet gun (18.91 ms) is less than that of the traditional single-barrel gun (more than 60 ms). Therefore, the newly designed gas-controlled side-jet gun significantly reduces the recoil momentum without losing the projectile velocity and continuous firing mode. [ABSTRACT FROM AUTHOR]

Copyright of Problems of Mechatronics. Armament, Aviation, Safety Engineering / Problemy Mechatroniki. Uzbrojenie, lotnictwo, Inżynieria Bezpieczeństwa is the property of Index Copernicus International and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper describes the method and results of an experimental study of unsteady burning rate of high-energy materials containing metal powder additives under depressurization at a rate of 140–160 MPa/s. The method based on stating and solving the inverse problem of internal ballistics is used to determine the unsteady burning rate. The studies are carried out for high-energy materials, including energy additives in the form of metal powders (ASD-4, ASD-6, and Alex aluminum powders), aluminum diboride, and dodecaboride. It is shown by analyzing the this study that the unsteady burning rate of high-energy materials under sharp depressurization is oscillatory and depends on the energy additive type. [ABSTRACT FROM AUTHOR]

Secondary blast injuries may result from high-velocity projectile fragments which ultimately increase medical costs, reduce active work time, and decrease quality of life. The role of skin penetration requires more investigation in energy absorption and surface mechanics for implementation in computational ballistic models. High-speed ballistic penetration studies have not considered penetrating and non-penetrating biomechanical properties of the skin, including radial wave displacement, resultant surface wave speed, or projectile material influence. A helium-pressurized launcher was used to accelerate 3/8″ (9.525 mm) diameter spherical projectiles toward seventeen whole porcine legs from seven pigs (39.53 ± 7.28 kg) at projectile velocities below and above V50. Projectiles included a mix of materials: stainless steel (n = 26), Si3N4 (n = 24), and acetal plastic (n = 24). Tracker video analysis software was used to determine projectile velocity at impact from the perpendicular view and motion of the tissue displacement wave from the in-line view. Average radial wave displacement and surface wave speed were calculated for each projectile material and categorized by penetrating or non-penetrating impacts. Two-sample t-tests determined that non-penetrating projectiles resulted in significantly faster surface wave speeds in porcine skin for stainless steel (p = 0.002), plastic (p = 0.004), and Si3N4 ball bearings (p = 0.014), while ANOVA determined significant differences in radial wave displacement and surface wave speed between projectile materials. Surface wave speed was used to quantify mechanical properties of the skin including elastic modulus, shear modulus, and bulk modulus during ballistic impact, which may be implemented to simulate accurate deformation behavior in computational impact models. [ABSTRACT FROM AUTHOR]

Pepper spray launchers are more precise and wind stable compared to conventional pepper sprays and are commonly used as a self-defensive tool. With the advanced potential, they may also harbour a greater risk for injuries, especially if they are not used within the suggested safety distance. If the shooting distance is below 1.5 m, energy densities may exceed the threshold energy density for the penetration of skin leading to skin laceration. We present a case where a man is hit by the liquid jet of a JPX Jet Protector® with an estimated shooting distance of 0.3 m. The man suffered from a bleeding skin laceration, which had to be sewed in the hospital. This case report furthermore outlines the potentially dangerous effect of pepper spray launchers and thereby their role in forensic investigations. [ABSTRACT FROM AUTHOR]

Gunshot residues (GSRs) play an important role in forensic investigations of gun-related violence. The presence of GSRs has been described to help to identify the bullet entry area, as it was supposed not to be found at exit wounds. This report details the suicidal headshot of an 84-year-old male where unburned tube-like, cuboid and flake-formed powder particles have been found not only at the inside of the muzzle but also circular around the exit wound. With very short-barrelled weapons, it must be expected that part of the propellant charge leaves the barrel unburned behind the bullet. In contrast to that, the barrel length of the used weapon should lead to a complete burn-up of powder particles. The surprisingly large number of unburned powder particles present at the exit wound of the injury gave reason for further investigation to understand the underlying ballistic aspects and outlines the importance of having a close look at incidence scene photos during an investigation. [ABSTRACT FROM AUTHOR]

In the paper we apply asymptotic technique based on the method of stationary phase and obtain the approximate analytical description of thermal motions caused by a source on an isotopic defect of an arbitrary mass in a 1D harmonic crystal. It is well known that localized oscillation is possible in this system in the case of a light defect. We consider the unsteady heat propagation and obtain formulae, which provide continualization (everywhere excepting a neighbourhood of a defect) and asymptotic uncoupling of the thermal motion into the sum of the slow and fast components. The slow motion is related to ballistic heat transport, whereas the fast motion is energy oscillation related to transformation of the kinetic energy into the potential one and in the opposite direction. To obtain the propagating component of the fast and slow motions we estimate the exact solution in the integral form at a moving point of observation. We demonstrate that the propagating parts of the slow and the fast motions are "anti-localized" near the defect. The physical meaning of the anti-localization is a tendency for the unsteady propagating wave-field to avoid a neighbourhood of a defect. The effect of anti-localization increases with the absolute value of the difference between the alternated mass and the mass of a regular particle, and, therefore, more energy concentrates just behind the leading wave-front of the propagating component. The obtained solution is valid in a wide range of a spatial co-ordinate (i.e. a particle number), everywhere excepting a neighbourhood of the leading wave-front. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Ballistics / Dandao Xuebao is the property of Journal of Ballistics Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Journal of Ordnance Equipment Engineering is the property of Chongqing University of Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this research, the numerical analysis is conducted to study the aerodynamic characteristics of the rocket target RT-400M with two motors arranged in parallel configuration with different nose cone shapes and performed ballistics analysis on drag values obtained from the finalised nose shape. Two RM 12K motors are used to increase range. This method reduces the R&D cost required to develop the new rocket motor with extended thrust. Reynolds averaged Navier-Strokes equation with k-ω SST model is adapted for the analysis. A parabolic nose shape produces the least values of drag, drag coefficient, and required velocities. A rocket target with a parabolic nose produces a maximum cd value of 0.29 and is used for the external ballistic calculation. Thrust values of the two motors are obtained from the experimental study. This rocket configuration reaches a maximum of 7800 m distance and a maximum of 3750 m in altitude. [ABSTRACT FROM AUTHOR]

Different charge structures have different interior ballistic performance. Existing research is based on experimental measurements or the lumped parameter method to obtain limited ballistic characteristics, which indirectly impacts the analysis of the parameters' distribution, requiring a complex modeling solution process. Besides this, the ignition performance of different charge structures needs to be further explored. The disadvantages of previous studies have limited the feasibility of further optimization of the composite charge structure. In this paper, we apply a two-dimensional two-phase flow method based on the Eulerian–Lagrangian model to study the performance of different composite charge structures. First, we establish the mathematical model of different particle types based on interior ballistics, which is directly related to the research foundation of subsequent ballistic performance. Next, we investigate the multi-scale reaction flow of complex charge structures by the two-phase flow method and obtain the distribution of parameters in the chamber. Finally, we conduct a study with different particle charge parameters to explore the sensitivity of ballistic characteristics to structural parameters. The results show that the tubular propellant has good ignition performance in different charge structures, and the ignition consistency can be improved by charging tubular propellant in the center of the chamber. However, more tubular propellants are ineffective at significantly improving ignition performance, and result in a decrease in combustion chamber pressure. These results may be promising for the optimization of various charge structures. [ABSTRACT FROM AUTHOR]

Rare earth-doped zinc oxide (ZnO:RE) systems are attractive for future optoelectronic devices such as phosphors, displays, and LEDs with emission in the visible spectral range, working even in a radiation-intense environment. The technology of these systems is currently under development, opening up new fields of application due to the low-cost production. Ion implantation is a very promising technique to incorporate rare-earth dopants into ZnO. However, the ballistic nature of this process makes the use of annealing essential. The selection of implantation parameters, as well as post-implantation annealing, turns out to be non-trivial because they determine the luminous efficiency of the ZnO:RE system. This paper presents a comprehensive study of the optimal implantation and annealing conditions, ensuring the most efficient luminescence of RE3+ ions in the ZnO matrix. Deep and shallow implantations, implantations performed at high and room temperature with various fluencies, as well as a range of post-RT implantation annealing processes are tested: rapid thermal annealing (minute duration) under different temperatures, times, and atmospheres (O2, N2, and Ar), flash lamp annealing (millisecond duration) and pulse plasma annealing (microsecond duration). It is shown that the highest luminescence efficiency of RE3+ is obtained for the shallow implantation at RT with the optimal fluence of 1.0 × 1015 RE ions/cm2 followed by a 10 min annealing in oxygen at 800 °C, and the light emission from such a ZnO:RE system is so bright that can be observed with the naked eye. [ABSTRACT FROM AUTHOR]

Fabrics with proper mechanical properties and high structural designability are frequently selected as the reinforcement of flexible composites. Shear thickening materials (STMs), including shear thickening fluid and shear thickening gel, are dense colloidal suspensions exhibiting an abrupt increase in viscosity with increasing shear rate. Shear thickening fabric composites (STFCs) which combined STM with fabrics, have been increasingly in demand for impact protective applications due to their tremendous potential. Herein, the characteristics of STM and the effects of fabric reinforcement on STFC impact behaviors are discussed for optimizing their properties and structures. Subsequently, the impact behaviors of STFCs obtained by multiple testing approaches with different impact threats are reviewed systematically. Furthermore, a comprehensive summary of the existing literature on stab, drop-weight, split Hopkinson pressure bar, and ballistic impact protective mechanisms of STFCs is presented. It is found that based on the proper selection of STM types, thorough mechanistic explanations of STFC impact behaviors are instructive and could facilitate the development of wearable protective equipment. The purpose of this critical review is to provide a framework for comparison of the effective impact resistances of STFCs across many applications and to discuss issues for future research. [ABSTRACT FROM AUTHOR]

This article describes fine tuning of wear diagnostics of a laboratory smooth barrel with a length of 5 m and diameter of 30 mm during tests. The devices are developed for measurements of internal diameter and force of pulling a piston prototype through the entire barrel length. An analog–digital instrument for measurement of internal diameter allows one to detect and to measure defects of arbitrary deformed barrel. The dimensions of the sensors used in the device allow us to scale it up for measurements of barrel of both lower and higher diameter. The device of force measurements allows us to estimate the friction parameters before experiments to clarify the mathematical model of gas dynamic processes accompanying the shot and to adjust loading conditions, if necessary. It has been demonstrated that their use allows us to estimate wear and to diagnose the state of the barrel system. Significant broadening of bore on the side of the breech end of the barrel has been detected. There is a correlation of measured data from both instruments. A ballistic experiment has been carried out using the updated measuring and recording complex. On the basis of the results the friction parameters of the piston–barrel couple obtained before the experiments have been accounted in the mathematical model of gas dynamic processes. This has allowed us to reduce the number of matching parameters upon simulation and to perform more accurate analysis of gas dynamic processes accompanying a shot with plotting respective time dependences of piston pressure and speed as well as distribution of maximum gas temperatures and pressure along the barrel length. Thus, the coefficient of the law of gunpowder burning has increased by 10%. [ABSTRACT FROM AUTHOR]

Several aspects make nitrocellulose based powders adequate as a solid propellant for rockets and missiles and the prefe rable propellant to be used in firearms and artillery: it produces less smoke and less fouling than other propellants; its burning rate shows a well-defined relation to pressure and the composition of the gaseous mixture resulting from its decomposition by burning can be predicted with relatively high levels of accuracy. This last feature, if coupled with adequate thermodynamic models, leads to a reliable framework for the simulation of internal ballistics and, ultimately, to an efficient design. Some simpler models use an ideal gas approach, which is obviously not adequate, and some others perform corrections based on the Virial E quation of S tate for sake of algebraic simplicity. This work employs the Peng-Robinson equation of state to model the pressurevolume-temperature (PVT) behavior of the gases produced during the burning reaction, once it is known to be accurate in the high pressures obtained inside combustion chambers. The results were compared to experimental data obtained in a closed vessel device and showed that the Peng-Robinson equation of state could predict the chamber pressure with higher accuracy. [ABSTRACT FROM AUTHOR]

Fragments and blast waves generated by explosions pose a serious threat to protective structures. In this paper, the impact resistance of polyurea-coated steel plate under complex dynamic loading is analyzed and designed for improving comprehensive ballistic and blast resistance using the newly established computational evaluating model. Firstly, according to the thickness and placement effects of the coating on the impact resistance, the steel-core sandwich plates are designed, which are proved to own outstanding comprehensive ballistic and blast resistance. Besides, the distribution diagram of ballistic and blast resistance for different polyurea-coated steel plates is given to guide the design of protective structures applying in different explosion scenarios. Furthermore, the dynamic response of designed plates under two scenarios with combined fragments and blast loading is studied. The results show that the synergistic effect of the combined loading reduces both the ballistic and blast resistance of the polyurea-coated steel plate. Besides, the acting sequence of the fragments and blast affects the structural protective performance heavily. It is found that the first loading inducing structural large deformation or damage is dominant. When fragments impact first, the excellent unit-thickness ballistic performance of the structural front part is strongly needed for improving the comprehensive ballistic and blast resistance. [ABSTRACT FROM AUTHOR]

Forensic science plays a critical role in the United States criminal legal system. For decades, many featurebased fields of forensic science, such as firearm and toolmark identification, developed outside the scientific community’s purview. The results of these studies are widely relied on by judges nationwide. However, this reliance is misplaced. Black-box studies to date suffer from inappropriate sampling methods and high rates of missingness. Current black-box studies ignore both problems in arriving at the error rate estimates presented to courts. We explore the impact of each type of limitation using available data from blackbox studies and court materials. We show that black-box studies rely on unrepresentative samples of examiners. Using a case study of a popular ballistics study, we find evidence that these nonrepresentative samples may commit fewer errors than the wider population from which they came. We also find evidence that the missingness in black-box studies is non-ignorable. Using data from a recent latent print study, we show that ignoring this missingness likely results in systematic underestimates of error rates. Finally, we offer concrete steps to overcome these limitations. Supplementary materials for this article are available online. [ABSTRACT FROM AUTHOR]