Search

To extend the application of cost-effective high-yield pulps in packaging, strength and barrier properties are improved by advanced-strength additives or by hot-pressing. The aim of this study is to assess the synergic effects between the two approaches by using nanocellulose as a bulk additive, and by hot-pressing technology. Due to the synergic effect, dry strength increases by 118% while individual improvements are 31% by nanocellulose and 92% by hot-pressing. This effect is higher for mechanical fibrillated cellulose. After hot-pressing, all papers retain more than 22% of their dry strength. Hot-pressing greatly increases the paper’s ability to withstand compressive forces applied in short periods of time by 84%, with a further 30% increase due to the synergic effect of the fibrillated nanocellulose. Hot-pressing and the fibrillated cellulose greatly decrease air permeability (80% and 68%, respectively) for refining pretreated samples, due to the increased fiber flexibility, which increase up to 90% using the combined effect. The tear index increases with the addition of nanocellulose, but this effect is lost after hot-pressing. In general, fibrillation degree has a small effect which means that low- cost nanocellulose could be used in hot-pressed papers, providing products with a good strength and barrier capacity.

Internationally, teachers use oral reading fluency (ORF) measurements to monitor learning progress in reading and adapt instruction to the individual needs of students. In ORF measures, the child reads aloud single syllables, words, or short passages, and the teacher rates in parallel at which items the child makes a mistake. Since administering paper-based ORF requires increased effort on the part of teachers, computer-based test administration is available. However, there are still concerns about the comparability of paper-based and computer-based test modes. In our study, we examine mode effects between paper-based and computer-based test scores for both reading speed and reading accuracy using a German-language ORF assessment for progress monitoring. 2nd- and 3rd-year-students (N = 359) with and without special education needs participated in the study. Results show comparable and high reliability (r > 0.76) and no differential item functioning for both test modes. Furthermore, students showed significantly higher reading speed on the paper-based test, while no differences were found in reading accuracy. In the absence of differential item functioning, we discuss how mean differences can be accounted for, how teachers can be trained to use the different test modes, and how computer-based tests can be safeguarded in practice.

Paper-based friction material is a typical paper-based composite that is usually cured via hot-pressing. This curing method does not account for the effect of pressure on the matrix resin, resulting in uneven distribution of resin in the material and reducing the mechanical properties of friction materials. To overcome the above shortcomings, a pre-curing method was introduced before hot-pressing, and the effects of different pre-curing degrees on the surface morphology and mechanical properties of paper-based friction materials were studied. The pre-curing degree significantly affected the resin distribution and interfacial bonding strength of the paper-based friction material. When the material was cured at 160 °C for 10 min, the pre-curing degree reached 60%. At this point, most of the resin was in a gel state, which could retain abundant pore structures on the material surface without causing mechanical damage to the fiber and resin matrix during hot-pressing. Ultimately, the paper-based friction material exhibited improved static mechanical properties, decreased permanent deformation, and reasonable dynamic mechanical properties.

Packaging is defined as the enclosement and protection of products for their distribution, storage, sale, consumption, and use [1], with the preferred material being paper and cardboard-based packages. Taking this into consideration, by 2021 the global paper industry reported a market value of 372.34 billion USD [2] and a production volume of approximately 417.3 million metric tonnes [3]. Therefore, when assessing global waste composition trends, it is not surprising to find that the most prominent stream after organic waste corresponds to paper and cardboard with a 17% representation [4]. Considering the above as well as the Sustainable Development Goals (SDG) tackling sustainable consumption and production patterns (Goal 12), the necessity to take urgent action to combat climate change and its impacts (Goal 13), and sustainably manage forests, combat desertification, halt and reverse land degradation and halt biodiversity loss (Goal 15), the following research had as its main objective to measure the impact of commonly used inks, coatings, varnishes, and decorations in paper and cardboard packaging repulpability according to the American Fibre Box Association (FBA) repulpability standard. Ten (10) samples employing digital printing – 2 samples – Offset printing in cardboard packages – 5 samples – and Offset printing in paper labels – 3 samples – were sourced from Kaunas University of Technology Publishing House and packaging manufacturer Trustpack, Lithuania. Results show that 3 out of the 10 samples produced more than 15% of rejects, and therefore cannot be considered repulpable. Additionally, the 3 samples show the inclusion on foil paints or metallized engravings, which supports the conclusion that the addition of such materials to the packaging significantly reduce the amount of recoverable material., Pakuotė apibrėžiama kaip produktų uždengimas ir apsauga, skirta jų platinimui, laikymui, pardavimui, vartojimui ir naudojimui [1], o populiariausia medžiaga yra popierinės ir kartoninės pakuotės. Atsižvelgiant į tai, iki 2021 m. pasaulinės popieriaus pramonės rinkos vertė siekė 372.34 mlrd. dolerių [2], o gamybos apimtis - apie 417,3 mln. metrinių tonų [3]. Todėl, vertinant pasaulines atliekų sudėties tendencijas, nenuostabu, kad po organinių atliekų svarbiausią srautą atitinka popierius ir kartonas, kurių dalis sudaro 17 % [4]. Atsižvelgiant į tai, kas išdėstyta pirmiau, taip pat į Darnaus vystymosi tikslus (DVT), kuriuose sprendžiamas tvaraus vartojimo ir gamybos modelių klausimas (12 tikslas), būtinybę imtis skubių veiksmų kovojant su klimato kaita ir jos poveikiu (13 tikslas), tvariai tvarkyti miškus, kovoti su dykumėjimu, sustabdyti ir pakeisti žemės degradaciją ir sustabdyti biologinės įvairovės nykimą (15 tikslas), šio tyrimo pagrindinis tikslas buvo įvertinti dažniausiai naudojamų rašalų, dangų, lakų ir dekoracijų poveikį popieriaus ir kartono pakuočių atstūmimui pagal Amerikos pluošto dėžučių asociacijos (FBA) atstūmimo standartą. Dešimt (10) pavyzdžių, kuriuose naudota skaitmeninė spauda - 2 pavyzdžiai, ofsetinė spauda kartoninėse pakuotėse - 5 pavyzdžiai ir ofsetinė spauda popierinėse etiketėse - 3 pavyzdžiai, buvo gauti iš Kauno technologijos universiteto leidyklos ir pakuočių gamintojo Trustpack, Lietuva. Rezultatai rodo, kad 3 iš 10 pavyzdžių buvo gauta daugiau kaip 15 % broko, todėl jų negalima laikyti atpažįstamais. Be to, šiuose 3 mėginiuose matyti, kad į pakuotę įtraukta ant folijos dažų arba metalizuotų graviūrų, o tai patvirtina išvadą, kad tokių medžiagų įtraukimas į pakuotę gerokai sumažina atgautinos medžiagos kiekį.

Paper has gained popularity as a packaging material due to its reduced environmental impact compared with non-degradable alternatives. However, its flammability poses safety risks, prompting research on enhancing its flame retardancy. This work introduces a diffusion-driven self-assembly strategy (DDSAS) to create a functional graphene oxide (GO) coating on various packaging papers. DDSAS involves infiltrating the paper’s cellulose microfiber network with branched polyethyleneimine (b-PEI), which binds firmly to cellulose microfibers. Electrostatic interactions between GO and b-PEI then drive GO assembly into a densely stacked, layered structure on the paper surface. This GO structure provides a physical barrier against flames and generates incombustible gases (CO2, H2O, NO2, and NO) when heated, diluting the surrounding oxygen concentration and acting as a heat insulation layer. These factors increase the flame retardancy of treated papers ten-fold. Additionally, the gradual reduction of GO upon heating forms reduced graphene oxide (rGO) on the paper, significantly increasing its electrical conductivity. As a result, the flame-retardant papers not only prevent the fire from spreading but can also act as fire sensors by triggering an alarm signal at the early stages of contact with fire. In summary, this work offers a rational strategy for designing and manufacturing flame-retardant paper packaging materials.

This article presents results on the use of a new material as a solidifying agent and/or color-fixing agent. A special polysaccharide material extracted from the prickly pear cactus (Opuntia ficus indica) was tested on historical materials and modern papers. An old book from the 18th century was chosen as historical material. From the mentioned book 42 pages were taken, on which a conservation and restoration pretreatment was performed before applying the polysaccharide material: sampling, fiber analysis, dry cleaning, ink solubility, pH test, thickness measurement and wet cleaning. The paper sheets provided for the test were divided into 4 groups, 3 of which were treated with gel and one left untreated as a reference. The division into groups is not only due to the different method of application, but also due to the process of gel extraction. The effect of the treatment was analyzed using FTIR-ATR. To test the mucilage as color-fixing agent 2 samples were prepared using watercolor papers colored with 6 different watercolors applied to 2.5 cm2 samples for each color in two rows of different intensity. One of the 2 samples was treated with gel, but both were immersed for 3 times in a water-ethanol solution for approximately 20 min as is standard practice in conservation and restoration. After washing, both specimens were subjected to colorimetric analysis to assess their differences. The results provided satisfactory evidence for the protection of paints sensitive to aqueous treatments and suggest the use of mucilage as a new material in cleaning method for water-soluble media.

The object of research in this scientific paper is the treatment of waste generated by paper production in industrial landfills. In the part of the paper production process, i.e. in its subsystem for wastewater treatment, a significant amount of solid waste is generated, which ends up in industrial landfills. The reason for the impossibility of returning to the production process lies in the fact that the sludge contains larger amounts of moisture and present chemical components that are isolated in the paper production process or during wastewater treatment. In the experimental part of the paper, a “trial plot” was selected on which seedlings of the paulownia elongate plant were planted in the waste sludge. The process of plant growth was monitored for two years and bioremediation, i.e. transfer of elements from sediments to plants, was analysed by modern instrumental methods. Based on the results obtained by research, it can be said with certainty that Paulownia elongate can be used in bioremediation of areas where these sediments are deposited.

In an article to study the effect of sizing agent and filler on the structural features of paper from the cellulose mass of the inner layer of the bark of mulberry tree branches, mechanical strength, absorbency and sorption properties were studied. Tensile strength was determined on a tensile testing machine by the force causing the destruction of the sample. Surface absorbency at one side wetting was determined by the method of Cobb(30), by determining the mass of water absorbed by the surface of the paper when wetting one side of the test sample. Sorption properties were studied on a high-vacuum setup with mercury gates and McBain quartz balances according to water vapor sorption data. It was found that the internal 2% sizing of the paper pulp with cherry tree resin glue contributes to the strengthening of the paper structure, which is confirmed by the values of mechanical strength and surface absorbency when unilaterally wetted with water, relative to the values obtained when sizing with pine oleoresin rosin glue. When using glue from cherry resin, it is advisable to add 2 g of kaolin to 100 g of pulp from the inner layer of the bark of mulberry tree branches, since the increase negatively affects mechanical strength and hydrophobicity., В статье для исследования влияния проклеивающего вещества и наполнителя на структурные особенности бумаги из целлюлозной массы внутреннего слоя коры веток тутового дерева изучены механическая прочность, впитывающая способность и сорбционные свойства. Прочность на разрыв при растяжении определяли на разрывной машине по усилию, вызывающему разрушение образца. Поверхностную впитываемость при одностороннем смачивании определяли по методу Кобб(30), путем определения массы воды, поглощенной поверхностью бумаги при смачивании одной стороны испытуемого образца. Сорбционные свойства исследовали на высоковакуумной установке с ртутными затворами и кварцевыми весами Мак-Бена по данным сорбции паров воды. Выявлено, что внутренняя 2%-ная проклейка бумажной массы клеем из живицы черешневого дерева способствует упрочнению структуры бумаги, что подтверждается значениями механической прочности и поверхностной впитываемостью при одностороннем смачивании водой, относительно значений, полученных при проклейке канифольным клеем из сосновой живицы. При использовании клея из живицы черешневого дерева целесообразно к 100 г целлюлозной массы из внутреннего слоя коры веток тутового дерева добавлять каолин в количестве 2 г, так как увеличение отрицательно влияет на механическую прочность и гидрофобность.

Lead (Pb) pollution from local mines and industrial use increases risks for human, animal, and plant health. Pectin is an effective chelator of Pb, and it has been shown that a unicellular green alga, Penium margaritaceum, synthesizes pectin in the cell wall. In this study, the ability of P. margaritaceum to remove Pb from an aqueous solution was investigated. Energy dispersive X-ray spectroscopy revealed that two strains of P. margaritaceum accumulated Pb on the cell surface. Hence, P. margaritaceum cells were immobilized on cellulose filter paper. The immobilized algal cells were soaked in 1.0 mg/L Pb solution with gentle shaking for 8 h, and Pb in the solution and on the filter paper was measured by flame atomic absorption spectrometry. The immobilized algal cells continuously decreased the Pb concentration to less than 0.5 mg/L and recovered 31.8–32.7% of added Pb. The specific decrease in Pb and increase in Ca were observed in the presence of 1.0 mg/L each of Ca, Mg, Na, and K. Fourier transform infrared spectra suggested that the carboxylic acid group would be responsible for the adsorption of Pb. This study is the first to demonstrate the effectiveness of the immobilized P. margaritaceum cell in removing Pb from aqueous solutions with simple solid–liquid separation.

Programa de doctorat: Doctorat en Enginyeria Tèxtil i Paperera The different researching lines in the field of Preservation and Conservation of Cultural Heritage on Paper tend to evolve and join other scientific fields in order to comprehend and embrace all the problematics caused by the aging of paper and its nature. Almost every decision made to stabilize the biochemical deterioration of cellulose is strongly conditioned by factors related to the papermaking process of that specific paper. These factors may include the fiber’s origin, the beating, the cooking and bleaching treatments, the technology used in the papermaking, the additives included in the fiber’s solution and posterior surface treatments such as the sizing or the coating among others. The field of Paper Engineering is focused on the development of papermaking technologies through new products and treatments. Those, in addition to the many testing methods used in this field –measurement of paper physical and optical properties, such as tensile strength or brightness ISO-, may be extrapolated to the field of Paper Conservation, adding new criteria and information about how any treatment affects the treated heritage, opening a window for new products and treatments, more bio-compatible with the cellulose nature, allowing to reduce the using of strong chemics and other procedures that are harmful for the environment.

Four organic solid wastes (coffee grounds, ground nut shell, paper money sewage sludge and cork powder) have been investigated as bloating inducing agents in lightweight aggregate (LWA) manufacturing when mixed in small proportions (2.5 wt.%) with three types of clays. The pellets obtained were fired in a rotary kiln at the maximum feasible temperature for 4 min. A similar impact was observed both in the working conditions and in the properties of the LWAs, showing that the differences between said residues are not as decisive as those of the clays to which they are added. The organic wastes have played a crucial role in achieving reducing conditions inside the aggregate. Thus, their addition has led to substantial improvements both from an operational point of view, lowering the working temperature, and from a technological perspective, favoring bloating and the development of a highly porous and lightweight structure. Leachate studies have shown that the LWAs meet the regulatory limits. The outcomes of this investigation show that, in line with the precepts of the Circular Economy, the recovery of organic wastes of different nature can have a place in the production of environmentally friendly LWAs

Background: Intelligent food packaging that can monitor food quality and safety is essential in modern commercial trade. Research on the fabrication of environmentally friendly colorimetric labels that can indicate the freshness of food through color changes are needed. Methods: In this study, paper-based colorimetric labels were prepared using filter paper dipped into a solution of Roselle flower extract, and their performance in monitoring shrimp spoilage was investigated. Results: The labels’ response to ammonia vapor shows a distinct color variation from red to greenish-grey, corresponding to a sharp increase in the total color difference (ΔE = 32). The labels are relatively stable during storage at 4°C for up to 20 days. In shrimp freshness monitoring, the color changes from red to purple, which corresponds to increasing levels of total volatile basic nitrogen (TVB-N), and can be observed easily with the naked eye. Conclusion: This suggests that our paper-based colorimetric labels impregnated with Roselle extract show superior performance in detecting shrimp spoilage.

Crowdsourcing in cultural heritage is rich in opportunities for collaborative, interdisciplinary research and practice. This presentation celebrates and calls for input and expansion of a White Paper that sets out current challenges and opportunities, and provides recommendations for the future of crowdsourcing in cultural heritage and the digital humanities.

This paper presents an evaluation and comparison of three state-of-the-art models for text summarization, and proposes a new digital reading interface designed for neophyte users to exploit these models, as well as automatic keyword extraction, with little or no programming experience.

W. H. Auden was among the most influential twentieth-century poets. New digital-edition projects aim to contribute to investigating his life and work in Austria. While the model of 'assertive edition' helps to address both philologically- and historically/biographically-oriented research interests, this paper will focus on formally representing uncertainty and editorial interpretation.

Carbon fiber paper (CFP) is one of the most important units of gas diffusion layer (GDL) in proton exchange membrane fuel cells (PEMFCs). The binder used in the wet-laid technique has a significant effect on the properties of CFP. In this work, the polyvinyl butyral/phenol-formaldehyde resin (PVB/PF) composite fibers firstly prepared by a dry spinning method were applied for CFP fabrication to replace traditional binders during the papermaking process and remove the PF impregnation process. In the composite fibers with a mass ratio of 5:5, PF phase with a size of about 2~3 μm evenly distributed in PVB matrix. PVB and PF were miscible to some degree, which was beneficial for their binding effect during hot-press. These composite fibers can successfully bind carbon fibers (CFs) during the papermaking process, and their residual carbon efficiently welded the CFs after heat treatment. The content and length of composite fibers in the mat affected the binding structure among CFs, which influenced the properties of CFP, increased the composite fibers’ content and reduced their length, significantly improving the strength of CFP. Therefore, the application of this solid fiber binder could enhance the comprehensive properties of CFP by adjusting the fibers’ parameters in the mat and also make the fabrication of CFP more environmentally friendly and low-cost.

This work presents the most important elements that affect the writing of scientific articles, but also those that determine the success for their acceptance and publication in impact journals. It also deals with aspects such as how to respond to peer review evaluations and how to disseminate the article once it has been published. The intended audience is trainee researchers and especially doctoral students who have chosen to carry out a thesis by compendium of publications. However, any researcher, junior or senior, will surely find several elements of interest in this work. It is also appropriate to add that the main academic background is that of social sciences in general and communication studies. This work is part of the development of methodologies within the project "Parameters and strategies to increase the relevance of media and digital communication in society: curation, visualization and visibility (CUVICOM)". PID2021-123579OB-I00 (MICINN), Ministry of Science and Innovation (Spain). Activity financed by the European Union- NextGenerationEU , Ministry of Universities and Recovery, Transformation and Resilience Plan, through a call from Pompeu Fabra University (Barcelona).

Today, legal regulations, along with social awareness, have made waste management a necessity. Depending on the type of waste, technological developments have enabled an increase in the number of approaches, e.g., reusing, recycling, and manufacturing of different products. In this study, low-density boards were produced using different proportions of office waste paper, wood chips, and chopped E-glass fiber. Waste paper and glass fiber formed the middle layer of the boards and wood chips comprised the surface layers. The density, water absorption, and thickness swelling properties of the boards were investigated. Among the mechanical properties, the modulus of rupture, modulus of elasticity, and internal bond strength were determined. The use of wastepaper led to a reduction in the modulus of rupture and modulus of elasticity of the boards. An increase in the glass fiber ratio contributed positively to the water absorption and thickness swelling properties, whereas it directly led to decreases in the internal bond strength, and the modulus of rupture and modulus of elasticity values. Nonetheless, the low-density boards were able to meet the minimum modulus of rupture and modulus of elasticity specified in ANSI 208.1 standards, while only one variation met the IB requirements., U današnje je vrijeme zakonska regulativa, uz društvenu svijest, gospodarenje otpadom učinila nužnošću. Ovisno o vrsti otpada, tehnološki je razvoj omogućio povećanje broja pristupa gospodarenju otpadom, npr. pri ponovnoj uporabi, recikliranju i proizvodnji različitih proizvoda. Za ovo su istraživanje izrađene ploče niske gustoće s različitim udjelima otpadnoga uredskog papira, drvnog iverja i usitnjenih staklenih vlakana. Pritom su otpadni papir i usitnjena staklena vlakna iskorišteni za izradu središnjeg sloja, a drvno je iverje upotrijebljeno za vanjske slojeve ploča. Izrađene su ploče ispitane i utvrđena je njihova gustoća, moć upijanja vode i debljinsko bubrenje. Dodatno su određeni modul loma, modul elastičnosti i čvrstoća raslojavanja. Rezultati ispitivanja pokazali su da je uporaba otpadnog papira pridonijela smanjenju vrijednosti modula loma i modula elastičnosti. Istodobno je povećanje udjela usitnjenih staklenih vlakana imalo pozitivan učinak na vrijednosti upijanja vode i na debljinsko bubrenje, ali je izravno utjecalo i na smanjenje čvrstoće raslojavanja, modula loma i modula elastičnosti. Ipak, izrađene ploče niske gustoće zadovoljile su minimalne zahtjeve norme ANSI 208.1 glede modula loma i modula elastičnosti, a samo je jedna skupina eksperimentalno izrađenih ploča zadovoljila uvjete čvrstoće raslojavanja.

Spatially resolved fluid-flow modulation and its corresponding integration becomes a crucial aspect to consider when designing high-performing paper-based analytical devices. As such, high demand exists for cost-effective techniques able to selectively control flow in patternable regions of the device. In this regard, a solution composed of potassium alum and animal glue; sizing materials used in the fabrication of calligraphy Xuan paper, is successfully adapted for the first time in a revolutionary approach to efficiently modulate the capillary flow in paper microfluidic channels. Flow delays are achieved by coating the substrate systematically through the variation of parameters such as the ratio of alum to glue, the concentration of alum-glue in the solution, and the number of subsequent coating layers of alum-glue. Moreover, digitized patterning with alum-glue is developed to achieve programmable wicking profiles of accelerating, decelerating, and quasi-linear flow displacement by alternating coated and uncoated zones in the channel. Additionally, the influence of alum-glue when performing biometric assays is investigated by performing a horseradish peroxidase activity colorimetric assay and found to have negligible effects on reading, where a negligible difference of 5.2% was observed in an assay performed in a coated paper substrate, compared to an uncoated one.

With the overarching aim for the development of sustainable, nontoxic wet strength agents for paper, a novel polymer gel system based on oxidized hydroxypropyl cellulose (keto-HPC) cross-linked with polyamines was investigated in detail to gain a deeper insight into the wet strength mechanism. When applied to paper, this wet strength system significantly increases the relative wet strength by using only low amounts of polymer, and it is therefore comparable with established wet strength agents based on fossil resources, such as polyamidoamine epichlorohydrin resins. With the help of ultrasonic treatment, keto-HPC was degraded with respect to its molecular weight and further cross-linked in paper using polymeric amine-reactive counterparts. The resulting polymer-cross-linked paper mechanical properties were analyzed with respect to the dry and wet tensile strength, respectively. In addition, we analyzed the polymer distribution using fluorescence confocal laser scanning microscopy (CLSM). If high-molecular-weight samples are being used for cross-linking, we do find accumulation of the polymer mainly on the surface of the fibers and at fiber crossing points, accompanied with enhancing strong effects on paper’s wet tensile strength. In contrast, if low-molecular-weight (i.e., degraded) keto-HPC is being applied, the macromolecules are capable of entering the inner porous structure of the paper fibers, and almost no accumulation at the fiber crossing points is observed, which also results in a lowered wet paper tensile strength, respectively. This insight into wet strength mechanisms of the keto-HPC/polyamine system can thus lead to new opportunities for the development of alternative biobased wet strength agents where molecular weight dependence of the wet tensile properties allows for a fine tuning of mechanical properties in the wet state.

Background Huntington’s disease is a complex neurodegenerative hereditary disease with symptoms in all domains of a person’s functioning. It begins after a healthy start in life and leads through the relentless progression over many years to complete care dependency and finally death. To date, the disease is incurable. The long progressive complex nature of the disease demands multiple disciplines for treatment and care of patient and family. These health care providers need inter- and multidisciplinary collaboration to persevere and be efficacious in this devastating disease trajectory. Discussion The position paper outlines current knowledge and experience alongside the experience and consensus of a recognised group of HD multidisciplinary experts. Additionally the patient’s voice is clear and calls for health care providers with a holistic view on patient and family. Building long-term trust is a cornerstone of the network around the patient. This paper describes a managed care network comprising all the needed professionals and services. In the health care system, the role of a central coordinator or case manager is of key importance but lacks an appropriate guideline. Other disciplines currently without guidelines are general practitioners, nurses, psychologists, and social workers. Guidelines for neurologists, psychiatrists, geneticists, occupational therapists, speech and language therapists, physiotherapists, dieticians, and dentists are being discussed. Apart from all these profession-specific guidelines, distinctive inter- and multidisciplinary collaboration requirements must be met. Conclusions and recommendations The complex nature of Huntington's disease demands multidisciplinary treatment and care endorsed by international regulations and the lay association. Available guidelines as reviewed in this paper should be used, made available by a central body, and updated every 3–5 years. Time needs to be invested in developing missing guidelines but the lack of this ‘proof’ should not prevent the ‘doing’ of good care.

Microfluidic paper-based analytical devices (μPADs) are emerging as powerful analytical platforms in clinical diagnostics, food safety, and environmental protection because of their low cost and favorable substrate properties for biosensing. However, the existing top-down fabrication methods of paper-based chips suffer from low resolution (200 μm). Additionally, papers have limitations in their physical properties (e.g., thickness, transmittance, and mechanical flexibility). Here, we demonstrate a bottom-up approach for the rapid fabrication of heterogeneously controlled paper-based chip arrays. We simply print a wax-patterned microchip with wettability contrasts, enabling automatic and selective assembly of cellulose microfibers to construct predefined paper-based microchip arrays with controllable thickness. This paper-based microchip printing technology is feasible for various substrate materials ranging from inorganic glass to organic polymers, providing a versatile platform for the full range of applications including transparent devices and flexible health monitoring. Our bottom-up printing technology using cellulose microfibers as the starting material provides a lateral resolution down to 42 ± 3 μm and achieves the narrowest channel barrier down to 33 ± 2 μm. As a proof-of-concept demonstration, a flexible paper-based glucose monitor is built for human health care, requiring only 0.3 μL of sample for testing.

In the European Union (EU), Regulation (EC) 1935/2004 provides a harmonized legal EU framework and sets out the general principles for safety and inertness for all Food Contact Materials (FCMs) and Food Contact Articles. From a food safety point of view, however, specific EU legislation for paper and cardboard FCMs is lacking, while at Member State level, national legislation differs among countries. More than 11,000 chemicals have been identified in all types of FCMs, most of them without any information on toxicity or migration potential from FCM to food. The present review shows a wide variability of protocols, approaches, and conditions used in scientific studies, which are difficult to compare. In this regard, procedures and conditions laid down in EU legislation for plastics and European Standards (EN protocols) may serve as a good basis for the future sample preparation procedures in the framework of paper and cardboard FCMs safety assessment. Challenges on sample preparation procedures are presented involving the interlinked steps of sample preparation, conditions used and their impact in chemical analysis and in vitro bioassay testing. Currently, there is no general consensus on the criteria for structuring, evaluating, and tuning sample preparation procedures for paper and cardboard FCMs. For this purpose, a set of modified criteria and a decision tree are proposed based on the literature. Along this, mass transfer processes occurring in paper and cardboard FCMs and parameters affecting chemical migration need to be accounted for prior to reaching general consensus on criteria for sample preparation procedures.

This work was developed within the scope of project i3N (LA/P/0037/2020. I.P. N. F. Santos thanks i3N for the BPD Grant BPD/UI96/5177/2020. S. O. Pereira thanks i3N for the BPD Grant BPD/UI96/5808/2017. The authors also thank Jonas Deuermeier for the XPS measurements. Publisher Copyright: © 2022 Elsevier Ltd Laser-induced graphene from paper (paper-LIG) was applied in non-enzymatic electrochemical sensing of uric acid (UA) in human urine. Paper-LIG was formed by CO2 laser modification of paper into a 3D graphene arrangement. Kinetic analysis of paper-LIG electrodes returned effective heterogeneous electron transfer standard rate constants of 1.4 × 10−3 cm s−1 and 7.8 × 10−4 cm s−1 for [Ru(NH3)6]2+/3+ and [Fe(CN)6]4−/3− redox probes, respectively. These electrodes were able to detect and quantify uric acid in PBS within the 10–300 μM range at pH between 5.6 and 7.4. At pH 7.4, a linear response (R2 = 0.999) from 10 to 250 μM was achieved, with a limit of detection of 3.97 μM and a sensitivity of 0.363 μA cm−2 μM−1. Paper-LIG electrodes denoted adequate selectivity in synthetic urine as well as in ascorbic acid (AA) and dopamine (DA)-containing electrolytes. Determination of urinary UA content in human samples returned a concentration of c.a. 1.8–1.9 mM, within the range for healthy individuals. Recoveries of samples spiked with 50 and 100 μM UA were 100.6% and 95.4%, respectively, with satisfactory reproducibility and stability. These cheap, lightweight, flexible, and eco-friendly paper-LIG biosensors for non-enzymatic quantification of UA in human urine pave the way to widespread application in the detection of other important biomarkers. publishersversion published

In the European Union (EU), Regulation (EC) 1935/2004 provides a harmonized legal EU framework and sets out the general principles for safety and inertness for all Food Contact Materials (FCMs) and Food Contact Articles. From a food safety point of view, however, specific EU legislation for paper and cardboard FCMs is lacking, while at Member State level, national legislation differs among countries. More than 11,000 chemicals have been identified in all types of FCMs, most of them without any information on toxicity or migration potential from FCM to food. The present review shows a wide variability of protocols, approaches, and conditions used in scientific studies, which are difficult to compare. In this regard, procedures and conditions laid down in EU legislation for plastics and European Standards (EN protocols) may serve as a good basis for the future sample preparation procedures in the framework of paper and cardboard FCMs safety assessment. Challenges on sample preparation procedures are presented involving the interlinked steps of sample preparation, conditions used and their impact in chemical analysis and in vitro bioassay testing. Currently, there is no general consensus on the criteria for structuring, evaluating, and tuning sample preparation procedures for paper and cardboard FCMs. For this purpose, a set of modified criteria and a decision tree are proposed based on the literature. Along this, mass transfer processes occurring in paper and cardboard FCMs and parameters affecting chemical migration need to be accounted for prior to reaching general consensus on criteria for sample preparation procedures.

In this paper, the behavior of the Bi-Material Cantilever (B-MaC) response deflection upon fluidic loading was experimentally studied and modeled for bilayer strips. A B-MaC consists of a strip of paper adhered to a strip of tape. When fluid is introduced, the paper expands while the tape does not, which causes the structure to bend due to strain mismatch, similar to the thermal loading of bi-metal thermostats. The main novelty of the paper-based bilayer cantilevers is the mechanical properties of two different types of material layers, a top layer of sensing paper and a bottom layer of actuating tape, to create a structure that can respond to moisture changes. When the sensing layer absorbs moisture, it causes the bilayer cantilever to bend or curl due to the differential swelling between the two layers. The portion of the paper strip that gets wet forms an arc, and as the fluid advances and fully wets the B-MaC, the entire B-MaC assumes the shape of the initial arc. This study showed that paper with higher hygroscopic expansion forms an arc with a smaller radius of curvature, whereas thicker tape with a higher Young’s modulus forms an arc with a larger radius of curvature. The results showed that the theoretical modeling could accurately predict the behavior of the bilayer strips. The significance of paper-based bilayer cantilevers lies in their potential applications in various fields, such as biomedicine, and environmental monitoring. In summary, the novelty and significance of paper-based bilayer cantilevers lie in their unique combination of sensing and actuating capabilities using a low-cost and environmentally friendly material.

Acknowledgements for the Sixth Volume of Papers on Postsecondary Learning and Teaching...iv Moving Forward in a Good Way: Nurturing the Spirit of Learning in Postsecondary Education ...i-iii Natoonikew Aansaamb...17-27 Not So “Mainstream”: The Need for Models of Indigenous Mentorship...1-8 Knowing Community through Story: It's Where We Come Together...9-16 Indigeneity, Positionality, and Ethical Space...36-48 Looking Back to Find a Way Forward...49-55 Integrating Indigenous Perspectives into Teacher Education in Alberta...28-35

Environmental toxic pollutants and pathogens that enter the ecosystem are major global issues. Detection of these toxic chemicals/pollutants and the diagnosis of a disease is a first step in efficiently controlling their contamination and spread, respectively. Various analytical techniques are available to detect and determine toxic chemicals/pathogens, including liquid chromatography, HPLC, mass spectroscopy, and enzyme-linked immunosorbent assays. However, these sensing strategies have some drawbacks such as tedious sample pretreatment and preparation, the requirement for skilled technicians, and dependence on large laboratory-based instruments. Alternatively, biosensors, especially paper-based sensors, could be used extensively and are a cost-effective alternative to conventional laboratory testing. They can improve accessibility to testing to identify chemicals and pollutants, especially in developing countries. Due to its low cost, abundance, easy disposal (by incineration, for example) and biocompatible nature, paper is considered a versatile material for the development of environmentally friendly electrochemical/optical (bio) sensor devices. This review presents an overview of sensing platforms constructed from paper, pointing out the main merits and demerits of paper-based sensing systems, their fabrication techniques, and the different optical/electrochemical detection techniques that they exploit.

Pseudoestrogene bisphenol A (BPA) can be important ingredient of thermochromic inks, increasingly used materials in thermal printing paper, security printing, advertising, design and as temperature indicators in medicine and food industry. BPA mass fraction in thermochromic inks can be up to several percent. Hence, disposal of items with thermochromic prints pose a risk of environmental pollution. In this work BPA mass fraction was monitored during anaerobic degradation of papers with thermochromic prints in soil in both matrices: papers and soil. The degradation conditions simulated deeper layers of waste at a landfill site. Six types of papers with prints of thermochromic ink containing 2% of BPA were subjected to anaerobic degradation over up to 150 days.

BAR - Brazilian Administration Review Call for papers: Special issue on Digital Technologies for Entrepreneurship and Social Change Main Topic: Digital technologies enable entrepreneurs to create innovations that can cross traditional industry boundaries, integrating digital and non-digital assets and scaling new ventures with new products, services, and business models (Nambisan, 2017; Nambisan et al., 2021). The ecosystem support for digital entrepreneurship can help to promote socioeconomic development, solve unemployment problems, generate innovative products and services, create a competitive environment, and increase local prosperity and well-being (Beliaeva et al., 2020). This special issue aims to diffuse research that focuses on the use of generative and emerging digital technologies, such as artificial intelligence, blockchain, IoT, and digital platforms (also known as Industry 4.0 technologies – Schwab & Davis, 2018) for digital entrepreneurship, especially when it aims to generate social impact. Research approaching the use of digital technologies as a driver for social change (for instance: new services for financial inclusion, employment opportunities, the promotion of diversity and environmental sustainability) are also targeted by this special issue. Important Dates: Submission of Full Paper: until October 31, 2023. Initial decision sent to authors: until March 31, 2024 Deadline for revised papers: July 31, 2024 Notification of acceptance: until September 31, 2024 Deadline for final versions: October 31, 2024 Special Issue publication (expected): December 2024 Guest Editors: Dr. Amarolinda Zanela Klein - Universidade do Vale do Rio dos Sinos, Business and Management School, Brazil (aczanela@unisinos.br) Dr. Cristiane Pedron - Universidade Nove de Julho, Brazil (cdpedron@uni9.pro.br) Dr. Silvia Elaluf-Calderwood - Florida International University, USA (selalufc@fiu.edu) Dr. Winnie Ng Picoto - Universidade de Lisboa, Instituto Superior Economia e Gestão, Portugal (w.picoto@iseg.ulisboa.pt) BAR Editor-in-Chief: Dr. Ivan Lapuente Garrido - Universidade do Vale do Rio dos Sinos, Business and Management School, Brazil (bar-eic@anpad.org.br) &nbsp

In the game of rock-paper-scissors with three players, this paper identifies conditions for a correlated equilibrium that differs from the mixed strategy Nash equilibrium and is evolutionarily stable. For this to occur, the correlation device attaches more probability to three-way ties and solo-winner outcomes than would result from the Nash equilibrium. The correlated equilibrium is evolutionarily stable because any mutant fares worse than a signal-following player when facing two players who follow their own correlated signals. The critical quality of the correlation device is to make this true both for potential mutants who would disobey their signal and instead choose the action which would beat the action signaled to the player, as well as for potential mutants who would deviate to the action that would be beaten by what the device signals to the player. These findings reveal how a strict correlated equilibrium can produce evolutionarily stable strategies for rock-paper-scissors with three players.

Purpose: The objective of this study was to investigate the factors of Social Media on Consumer Perception and Purchase Intention towards Brand Loyalty. Theoretical framework: A recent trend of Social media has affected customers in various way. This was a conceptual paper to explore that there is relationship of consumer perception and purchase intention as mediating variable towards brand loyally. A comprehensive literature survey was carried out to evaluate various factors relating to Social media and its effectiveness to Brand Loyalty mediating effect with consumer perception and purchase intention. Method: There were 102 research papers were analysis critically to find out the connection of factors of social media on consumer perception and purchase intention towards brand loyalty Results and Conclusion: entertainment, interaction, trust, e-word of mouth and online engagement as important factors influence mostly towards brand loyalty. Search implications: The study has made contribution to the marketing and promotion and offered useful research gap for their further research on the field. Originality/value: There was a positive effect of Trust, interaction, e-word of mouth, trendiness, entertainment and online customer engagement as factors of Social media marketing influence on Brand Loyalty mediating with consumer perception and purchase intention.

The 2023 release provides avaluable insights on some of the most pressing issues European Media Markets face today, including the impact COVID-19, TikTok, new business models, SVoD, Equality, Diversity and Inclusion, and technological developments, such as Artificial Intelligence and Blockchain. Each of the 10 White Papers is written by our graduate students of the European Media Market course of the international Master Programme in Communication Studies at the VUB. The papers are based on thorough research and analysis, making this series a resource for anyone interested in staying up-to-date on the latest developments in European Media Markets from students and academics to practitioners.

Міжнародний науковий журнал «Грааль науки» № 27 (травень, 2023) : за матеріалами V Міжнародної науково-практичної конференції «Science of post-industrial society: globalization and transformation processes», що проводилася 12 травня 2023 року ГО «Європейська наукова платформа» (Вінниця, Україна) та ТОВ «International Centre Corporative Management» (Відень, Австрія). У цій статті обговорюються питання, пов’язані з використанням паперової, біорозкладної та пластикової упаковки в харчовій промисловості. Представлено переваги та недоліки кожного пакувального матеріалу та проведено порівняльний аналіз. Обгооворювалися питання як екологічності, так і зручності використання в різних ситуаціях і сферах, пов'язаних з харчовою промисловістю. This paper discusses the issues related to the use of paper, biodegradable and plastic packaging in the food industry. The advantages and disadvantages of each packaging material were presented and a comparative analysis was developed. Both environmental friendliness and ease of use in different situations and areas related to the food industry were touched upon.

Paper is one of the oldest commodities used by mankind, having helped record its history throughout the ages. However, to talk about paper today, is to talk about something that goes beyond the simple matrix of cellulose fibers used as a support for printing and writing. Due to its biodegradability, recyclability, renewable character, and properties in general, paper is currently exploited in a wide range of applications, such as sensors or diagnostic papers. Yet, one of its most important applications is as a packaging material. To do this, papers are usually coated with a polymer in order to improve their water and air barrier properties. Most coating formulations are still based on polymers obtained from non-renewable sources, such as poly(ethylene-vinyl alcohol) (PEVOH) and polyvinylidene chloride (PVDC). In addition, these formulations rely on the use of volatile organic compounds (VOCs) as organic solvents (e.g. chloroform). With advances made in biomass refining, new biologically sourced and biodegradable polymers, such as poly(lactic acid) (PLA) and poly(hydroxyalkanoates) (PHAs), have been used to replace traditional polymers. However, despite their "greener" characteristics, even these polymers rely on application techniques that require the use of VOCs as solvents. An expedient way to functionalize paper, and of easy industrialization, is the application of photopolymerizable coatings. This type of coatings can be formulated without the use of traditional organic solvents, and the curing process is initiated by the incidence of light (usually UV), which can occur in a few seconds. Many of the monomers and other components used in the formulation of this type of coatings can come from renewable sources, also helping to reduce the current dependence on non-renewable sources. Therefore, the goal of this PhD was the functionalization of paper through the application of photopolymerizable coatings that would give this substrate new functionalities such as hydrophobicity and cholesteric properties. In this context, this work focused on the development of solvent-free formulations, giving priority to the use of renewable raw materials. The study started with the development of a solvent-free photopolymerizable coating based on a copolymer of two acrylic monomers, namely 2-ethylhexyl acrylate and isobornyl methacrylate in a molar ratio of 0.64/0.36, in order to obtain a paper with hydrophobic properties. Two formulations consisting of 50 and 60 wt% copolymer, a mixture of the monomers (in the same molar proportion as the copolymer), and the photoinitiator (PI) darocur 1173 were studied. The application of these formulations resulted in a significant increase in the hydrophobicity of the paper (water contact angle values greater than 120°, and a decrease in water adsorption with Cobb values of 11 g/m2), while maintaining (if not improving) the other properties of the paper, namely the mechanical and air barrier properties. In the same vein, a second solvent-free formulation was developed with the aim of also improving the hydrophobicity of the paper. The formulation was based on tung oil (a highly unsaturated vegetable oil) and Darocur 1173 (PI). The coated papers had their hydrophobicity significantly improved, evidenced by an increase in the water contact angle values from about 71 ° (uncoated paper) to 127 ° and a significant decrease in water absorption, as determined by the Cobb test, from 108 to 17 g/m2 after a curing time of only 15 s. Moreover, with this short curing time, the paper's optical properties (namely whiteness, gloss and opacity) were maintained, and its mechanical properties (namely tensile and burst strength) improved. The last formulation developed is part of a preliminary study, in which the cholesteric properties of aqueous hydroxypropylcellulose (HPC) mixtures were combined with a photopolymerizable system consisting of 2-hydroxyethyl methacrylate (HEMA, monomer) and benzophenone (PI). The aim of these formulations was to develop paper-based moisture sensors capable of changing their color when exposed to atmospheric moisture. The concentration of HPC (65, 68, and 68 wt%) and the HEMA:water ratio (1:2, 1.4:1, 1:1, 1:1.4, 1:2), were adjusted to produce cholesteric papers capable of exhibiting homogeneous color and appropriate moisture response. Preliminary test of exposure of said papers to atmospheres of high relative humidity (95 %) revealed that the color change (ΔE) increased with exposure time, being the color change clearly perceptible (ΔE between 13 and 16). However, further studies are needed in order to better adjust the moisture response of the developed sensors. In summary, the work developed throughout this thesis highlights the possibility of using conventional solvent-free photopolymerizable coatings to manufacture paper-based products with new functionalities. Not only can the formulations developed be easily applied to paper, but the possibility of using renewable materials and short irradiation times allows paper functionalization in an efficient, scalable and environmentally friendly way. This is undoubtedly a promising strategy for developing new paper products with innovative properties. O papel é uma das mais antigas comodidades utilizadas pela humanidade, tendo ajudado a registar a sua História ao longo dos tempos. Contudo, falar de papel hoje em dia, é falar de algo que vai além da simples matriz de fibras de celulose utilizada como suporte para impressão e escrita. Devido à sua biodegradabilidade, reciclabilidade, caráter renovável e propriedades em geral, o papel é atualmente explorado numa vasta gama de aplicações, como por exemplo, em sensores ou papéis de diagnóstico. No entanto, uma da sua aplicação mais importante é como material de embalagem. Para tal, os papéis são normalmente revestidos com um polímero de modo a melhorar as suas propriedades de barreira à água e ao ar. A maioria das formulações de revestimento baseia-se ainda em polímeros obtidos de fontes não renováveis, tais como o poli(álcool etileno vinílico) (PEVOH) e o poli(cloreto de vinilideno) (PVDC). Além disso, estas formulações dependem da utilização de compostos orgânicos voláteis (COV) como solventes orgânicos (ex. clorofórmio). Com os avanços alcançados na refinação da biomassa, novos polímeros de origem biológica e biodegradáveis, como o poli(ácido láctico) (PLA) e os poli(hidroxialcanoatos) (PHAs), têm vindo a ser utilizados para substituir os polímeros tradicionais. No entanto, apesar das suas características "mais verdes", mesmo estes polímeros dependem de técnicas de aplicação que requerem a utilização de COVs como solventes. Uma forma expedita de funcionalização do papel, e de fácil industrialização, é a aplicação de revestimentos fotopolimerizáveis. Este tipo de revestimentos pode ser formulado sem o uso dos solventes orgânicos tradicionais, sendo o processo de cura iniciado pela incidência de luz (por norma UV), que pode ocorrer em poucos segundos. Muitos dos monómeros e demais componentes usados na formulação deste tipo de revestimentos podem provir de fontes renováveis, ajudando também a reduzir a atual dependência em fontes não-renováveis. Portanto, o objetivo deste doutoramento foi a funcionalização do papel através da aplicação de revestimentos fotopolimerizáveis que conferissem a este substrato novas funcionalidades como hidrofobicidade e propriedades colestéricas. Nesse contexto, este trabalho centrou-se no desenvolvimento de formulações sem solventes, dando prioridade à utilização de matérias-primas renováveis. O estudo começou com o desenvolvimento de um revestimento fotopolimerizável sem solventes baseado num copolímero de dois monómeros acrílicos, nomeadamente o acrilato de 2-etilhexilo e o metacrilato de isobornilo numa proporção molar de 0,64/0,36, no sentido de obter um papel com propriedades hidrofóbicas. Foram estudadas duas formulações que consistiam em 50 e 60 wt% de copolímero, uma mistura dos monómeros (na mesma proporção molar que o copolímero), e o fotoiniciador (PI) darocur 1173. A aplicação destas formulações resultou num aumento significativo da hidrofobicidade do papel (valores de ângulo de contacto com a água superiores a 120 °, e um decréscimo da adsorção de água com valores de Cobb de 11 g/m2), mantendo (se não melhorando) as outras propriedades do papel, nomeadamente as propriedades mecânicas e de barreira ao ar. Na mesma linha, foi desenvolvida uma segunda formulação sem solventes com o objetivo de melhorar também a hidrofobicidade do papel. A formulação foi baseada em óleo de tungue (um óleo vegetal altamente insaturado) e Darocur 1173 (PI). Os papéis revestidos tiveram a sua hidrofobicidade significativamente melhorada, evidenciada pelo aumento dos valores do ângulo de contacto com água de cerca de 71 ° (papel não revestido) para 127 ° e pela diminuição significativa da absorção de água, determinada pelo teste Cobb, de 108 para 17 g/m2, após um tempo de cura de apenas 15 s. Além disso, com este curto tempo de cura, as propriedades óticas do papel (nomeadamente brancura, brilho e opacidade) foram mantidas e as suas propriedades mecânicas (nomeadamente resistência à tração e à rutura) melhoradas. A última formulação desenvolvida faz parte de um estudo preliminar, em que as propriedades colestéricas de misturas aquosas de hidroxipropilcelulose (HPC) foram combinadas com um sistema fotopolimerizável constituído por 2-hidroxietil metacrilato (HEMA, monómero) e benzofenona (PI). O objetivo destas formulações visou o desenvolvimento de sensores de humidade baseados em papel capazes de alterar a sua cor quando expostos à humidade atmosférica. A concentração de HPC (65, 68, e 68 % em massa) e o rácio HEMA:água (1:2, 1.4:1, 1:1, 1:1.4, 1:2), foram ajustados para produzir papéis colestéricos capazes de exibir uma cor homogénea e uma resposta adequada à humidade. O teste preliminar de exposição dos referidos papéis a atmosferas de elevada humidade relativa (95 %) revelou que a mudança de cor (ΔE) aumentou com o tempo de exposição, sendo a mudança de cor claramente percetível (ΔE entre 13 e 16). Contudo, é necessário realizar mais estudos de forma a ajustar melhor a resposta à humidade dos sensores desenvolvidos. Em suma, o trabalho desenvolvido ao longo desta tese destaca a possibilidade de utilizar revestimentos fotopolimerizáveis sem solventes convencionais para fabricar produtos à base de papel com novas funcionalidades. Não só as formulações desenvolvidas podem ser facilmente aplicadas no papel, mas a possibilidade de utilizar materiais renováveis e tempos de irradiação curtos permite a funcionalização do papel de uma forma eficiente, escalável e amiga do ambiente. Esta é sem dúvida uma estratégia promissora para o desenvolvimento de novos produtos de papel com propriedades inovadoras. Programa Doutoral em Engenharia Química

Newspapers publishers must now generate, print, and distribute their contents differently as a result of new publishing technologies like electronic paper (e-paper). In addition to posing technical difficulties for publishers, e-paper will alter how news items are consumed. By assuming a starting point in potential new consumption, we approach the influence of this new channel from the outside-in in this essay. We explore the effects that the e-paper publication channel will have on distribution, systems of media house, such as editorial, advertising, and subscription, and workflows based on three empirically supported future consuming scenarios., {"references":["1.\tLiu, Z., & Stork, D. G. (2000). Is paperless really more?. Communications of the ACM, 43(11), 94-97.","2.\tArena Partners (2005). Available at: http://www.arenapartners.fi April 5, 2005.","3.\tDagens Nyheter (2005). Available at http://www.dn.se April 5, 2005.","4.\tE Ink (2005). Avaliable at: http://www.eink.com February 23, 2005.","5.\tGo, K., & Carroll, J. M. (2004). The blind men and the elephant: Views of scenario-based system design. interactions, 11(6), 44-53.","6.\tGyricon (2005). Avaliable at: http://www.gyricon.com.","7.\tHayes, R. A., & Feenstra, B. J. (2003). Video-speed electronic paper based on electrowetting. Nature, 425(6956), 383-385.","8.\tIhlström Eriksson, C., Åkesson, M., & Nordqvist, S. (2004). From Print to Web to e-paper-the challenge of designing the e-newspaper.Ihlström Eriksson, C., Åkesson, M., & Nordqvist, S. (2004). From Print to Web to e-paper-the challenge of designing the e-newspaper.","9.\tJonsson, A., Hedin, B., & Sabelström Möller, K. (2002). A topic based approach to multiple channel news publishing. In The 29th International IARIGAI Research Conference, EMPA/UGRA, St. Gallen, 2002 (pp. 55-63).","10.\tLyytinen, K., & Yoo, Y. (2002). Research commentary: the next wave of nomadic computing. Information systems research, 13(4), 377-388."]}

Disposal of waste sludges produced in large amounts in the paper industry could generate significant environmental and health issues. One strategy to address them involves revalorization of deinking paper sludge (DPS) by reusing it as fertilizer. However, the possible human health risks associated with the use of DPS are still not well explored. The main objective of this report was to estimate DPS impacts on human toxicity. To achieve this goal, heavy metals analysis of the DPS waste (Cadmium; Cd, Copper; Cu; Molybdenum; Mo, Manganese; Mn; Lead; Pb; Cobalt; Co) was conducted. The assessment of human toxicity was performed by applying the UNEP/SETAC toxicity modelUSEtox 2.0to establish indicators that reflect the potential health damage of these chemicals when released into the environment. Laboratory analysis, revealed a very low concentration of the DPS by the metallic contaminants (Cd, Cu, Mo, Mn, Pb, Co). According to the USEtox model results, these quantities will not lead to either carcinogenic or non-carcinogenic risks on human health even if there is a use of very high quantities of DPS. Indeed, the number of cases /t DPS emitted in agricultural soils didn’t exceed 950.10-7for the non-carcinogenic effect and 3.71.10-7for the carcinogenic effect for Pb. For Mn and Co, we noticed no toxic effects (0 cases /t DPS emitted). Furthermore, we observed that Mo and Cu had very weak non-carcinogenic effects and led respectively to 445.10-7and 56.10-7cases /t DPS emitted.Regarding the effect of Cd toxicity, in order to have one case of this metal toxicity from DPS waste in our study, we had to use a very important quantity of DPS (≈2 821 680t). All these dataemphasizedon the absence of heath human toxicity risk after DPS waste industrial disposal, by ingestion or inhalation.

The effluents generated in the paper industry, such as black liquor, have a high content of lignin and other toxic components; however, they represent a source of lignin-degrading bacteria with biotechnological potential. Therefore, the present study aimed to isolate and identify lignin-degrading bacteria species in paper mill sludge. A primary isolation was carried out from samples of sludge present in environments around a paper company located in the province of Ascope (Peru). Bacteria selection was made by the degradation of Lignin Kraft as the only carbon source in a solid medium. Finally, the laccase activity (Um-L−1) of each selected bacteria was determined by oxidation of 2,2′-azinobis-(3-etilbencenotiazolina-6-sulfonate) (ABTS). Bacterial species with laccase activity were identified by molecular biology techniques. Seven species of bacteria with laccase activity and the ability to degrade lignin were identified. The bacteria Agrobacterium tumefasciens (2), Klebsiella grimontii (1), and Beijeinckia fluminensis (1) were reported for first time. K. grimowntii and B. fluminensis presented the highest laccase activity, with values of 0.319 ± 0.005 UmL−1 and 0.329 ± 0.004 UmL−1, respectively. In conclusion, paper mill sludge may represent a source of lignin-degrading bacteria with laccase activity, and they could have potential biotechnological applications.

In protecting cultural heritage, deacidification is used to stabilize acidic papers, ensuring the neutralization of acids present in the paper. But in the process of aging, several mechanisms of degradation occur simultaneously. Therefore, substances used to stabilize the paper should contain an antioxidant component in addition to the deacidifying component. The effect of the antioxidant (hindered amine light stabilizers—HALS type) on the stabilization of lignin-containing acid papers during accelerated aging was studied in this work. The effective deacidification component was magnesium; the solvent was hexamethyldisiloxane (HMDSO). The 4-amino-2,2,6,6-tetramethylpiperidine series of hindered amine light stabilizers (HALS) was selected as appropriate for creating a modifying system based on HMDSO. The modification system was tested on samples of a model test acid lignin-containing paper (NOVO) and naturally aged acidic paper from the real book. The addition of substances to the proposed deacidification system has a favorable effect on stabilizing the pH during aging and provides the inhibition of the oxidative degradation products and stabilization of the cellulose degree of polymerization. It was confirmed that the application of the system containing deacidification and an antioxidant component may increase the effectiveness of the protection of acid groundwood paper heritage objects. Adding a tested antioxidant to the proposed deacidification system has a favorable effect on stabilizing the pH value for a long time in accelerated aging.

As a sustainable and greener substitute for conventional paper products, hemp paper has the potential to revolutionise the paper industry. Hemp paper, which is made from hemp plant fibres, is more environmentally friendly than conventional paper made from trees and is by nature strong and resilient. Hemp paper offers a special business opportunity in light of the rising demand for eco-friendly products around the world and growing awareness of the negative environmental effects of traditional paper production. This abstract examines the advantages of hemp paper, the market's current state, and the difficulties that must be overcome to turn hemp paper into a lucrative business venture. Hemp paper has the potential to revolutionise the market by using cutting-edge production methods, addressing consumer concerns, and raising market awareness.

Light bleaching, as a treatment option for discoloured papers, is currently being reconsidered in the British Museum Western Art on Paper Conservation Studio. This research project was carried out in order to determine optimal and practical treatment conditions. Light bleaching experiments on artificially aged modern papers and naturally aged 18th century paper immersed in baths of filtered tap water, deionised water, sodium-based buffers, magnesium bicarbonate and calcium hydroxide at alkalinities ranging from pH 8 to pH 12 of have shown that, in general, solutions at a higher pH are more effective at removing discolouration than solutions at neutral pH values. Filtered tap water and deionised water were significantly less effective than any of the other solutions. Magnesium bicarbonate appeared particularly effective at removing discolouration in the dark as well as during light bleaching when compared to calcium hydroxide at neutral or mildly alkaline conditions. Treatments in calcium hydroxide at higher pH values (pH 10 to pH 12) were sometimes more effective than magnesium bicarbonate but this appeared to depend upon paper type and treatment time. Treatments in the sodiumbased buffers were generally the most effective, suggesting that borax may be an alternative to calcium hydroxide which can be laborious to keep at a stable pH for prolonged treatments. However, great care must be taken to fully rinse sodium tetraborate from the papers after treatment as colour reversion tests have shown that residual sodium tetraborate can lead to excessive discolouration., The British Museum; CSR Project no. 7391; 6 May 2011

BAR - Brazilian Administration Review Call for Papers: Special issue on Coopetition Main Topic: This special issue is designed to strengthen research on coopetition. As a paradoxical concept, coopetition involves firms interacting with two contradictory logics – competition and cooperation. The simultaneous cooperation and competition or the interplay – the sequential transition between the two – can give rise to important synergies among partners for knowledge development and learning but it may also generate tensions. Coopetition alludes to a cycle of creation and appropriation of value that can generate benefits such as – but not limited to – firms’ competitive advantages, cost reduction, access to resources and knowledge, expansion of customer base, etc. Overall, coopetition can be an effective business strategy for companies looking to achieve mutual benefits through combining competitive and cooperative relationships. Important Dates: Submission of Full Paper: until August 31, 2023. Initial decision sent to authors: until October 31, 2023 Deadline for revised papers: December 31, 2023 Notification of acceptance: until January 15, 2024 Deadline for final versions: February 20, 2024 Special Issue publication (expected): March 2024 Guest Editors: Dr. Jefferson Marlon Monticelli - Universidade do Vale do Rio dos Sinos, Business and Management School, Brazil (jmmonticelli@unisinos.br) Dr. Emilene Leite - Örebro University School of Business, Sweden (emilene.leite@oru.se) Dr. Adriana Fumi Chim Miki - Universidade Federal de Campina Grande, Graduate Program in Management, Brazil (adriana.c.miki@ufcg.edu.br) BAR Editor-in-Chief: Dr. Ivan Lapuente Garrido - Universidade do Vale do Rio dos Sinos, Business and Management School, Brazil (bar-eic@anpad.org.br)

Adenosine triphosphate (ATP) determination has been used for many decades to assess microbial contamination for hygiene monitoring in different locations and workplace environments. Highly sophisticated methods have been reported, yet commercially available kits rely on a luciferase–luciferin system and require storage and shipping at controlled temperatures (+4 or −20 °C). The applicability of these systems is limited by the need for a secure cold chain, which is not always applicable, especially in remote areas or low-resource settings. In this scenario, easy-to-handle and portable sensors would be highly valuable. Prompted by this need, we developed a bioluminescence paper biosensor for ATP monitoring in which a new luciferase mutant was combined with a metal–organic framework (MOF); i.e., zeolitic imidazolate framework-8 (ZIF-8). A paper biosensor was developed, ZIF-8@Luc paper sensor, and interfaced with different portable light detectors, including a silicon photomultiplier (SiPM) and smartphones. The use of ZIF-8 not only provided a five-fold increase in the bioluminescence signal, but also significantly improved the stability of the sensor, both at +4 and +28 °C. The ATP content in complex biological matrices was analyzed with the ZIF-8@Luc paper sensor, enabling detection down to 7 × 10−12 moles of ATP and 8 × 10−13 moles in bacterial lysates and urine samples, respectively. The ZIF-8@Luc sensor could, therefore, be applied in many fields in which ATP monitoring is required such as the control of microbial contamination.

The increase in anthropogenic pollution raises serious concerns regarding contamination of water bodies and aquatic species with potential implications on human health. Pharmaceutical compounds are a type of contaminants of emerging concern that are increasingly consumed and, thus, being frequently found in the aquatic environment. In this sense, an electrochemical sensor based on an unmodified and untreated carbon fiber paper (CPS—carbon paper sensor) was simply employed for the analysis of trimethoprim antibiotic in fish samples. First, the analytical conditions were thoroughly optimized in order for the CPS to achieve maximum performance in trimethoprim determination. Therefore, an electrolyte (0.1 M Britton–Robinson buffer) pH of 7 was selected and for square wave voltammetry parameters, optimum values of amplitude, frequency and step potential corresponded to 0.02 V, 50 Hz, and 0.015 V, respectively, whereas the deposition of analyte occurred at +0.7 V for 60 s. In these optimum conditions, the obtained liner range (0.05 to 2 µM), sensitivity (48.8 µA µM−1 cm−2), and LOD (0.065 µM) competes favorably with the commonly used GCE-based sensors or BDD electrodes that employ nanostructuration or are more expensive. The CPS was then applied for trimethoprim determination in fish samples after employing a solid phase extraction procedure based on QuEChERS salts, resulting in recoveries of 105.9 ± 1.8% by the standard addition method.

Historical evidences include inscriptions, copper plates, coins, palm leaf manuscripts and paper manuscripts. Many literary, grammatical, mathematical, medical, astronomical and historical works handed down to us by our forefathers are also present in paper trails. These are also primary sources of evidence in the field. In that sense, the role of paper traces is also primary in the edition history of Aganaanooru, one of the Sangam literatures. Considering the scope of the research, this article examines the editions that came before 1940 and highlights the utility of paper manuscripts in them.