Search

Background: The last two decades have seen a growing trend toward the use of inflatable membranes for spaceborne structures. The spaceborne inflatable membrane structures are the promising solution for the compact and lightweight reflector antenna. The inflation technique is used for pressurizing the inflatable membrane structure once the satellite reaches to its predefined orbit. Objective: The objective of the study is to demonstrate the use of the residue gas inflation technique for the complete deployment of the inflatable thin membrane boom with different folding patterns. The study also aims to find out generalized relation to calculate the safe mass of residue gases to be kept inside spaceborne membrane boom. Method: The novel analytical relation for the safe mass of residue gases that can be carried for any size of the inflatable boom is established. A comparative study is performed to investigate the effect of variation in a folding pattern on the proposed inflation technique. Experimental, numerical, and analytical approaches were employed for the proposed study. Result: The results show that the total inflation time is inversely proportional to the mass of the residue gases. Through the comparative study, it has been observed that the change in the inflation time is negligible for different folding patterns with the same mass of residue gas. The result confirms that the safe mass of residue gas is successfully deploying the inflatable boom in the vacuum environmental condition keeping the stresses in the boom in the tolerance limit. Conclusions: The findings of this research provide insights into a simple and cost-effective design solution for the inflation system along with safe mass of the residue gases which can be used for any size of spaceborne inflatable boom. [ABSTRACT FROM AUTHOR]

Inorganic photocatalytic materials exhibiting a highly efficient response to ultraviolet-visible light spectrum have become a subject of widespread global interest. Nanocomposite metal oxides, particularly Nickel Oxide (NiO) and Zinc Oxide (ZnO), have gained attention for their diverse applications in gas sensing and photocatalytic processes. In this work, ZnO-NiO (ZnO0.6NiO0.4 and ZnO0.4NiO0.6) binary nanocomposites were synthesized by hydrothermal technique. The binary nanocomposites were analyzed by UV-Visible spectrophotometer, X-ray diffraction (XRD), photoluminescence (PL), Fourier transform infrared spectrophotometer (FTIR), energy dispersive X-ray spectroscopy (EDX), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). The XRD pattern revealed that the nanocomposites, the peaks of both ZnO and NiO are present indicating the presence of both crystal structures hexagonal wurtzite and cubic. The miller indices, crystallite size, microstrain and dislocation density were determined from the XRD plot. FESEM and TEM analyses showed the spherical morphology of the synthesized composites with an approximate size of 10nm. The detailed analysis of ZnO–NiO binary nanocomposite sensor characteristics in terms of sensitivity, selectivity, response and recovery time were carried out and the nanocomposites were found to be highly sensitive to CO2 100 ppm at 350∘C and Cl2 at 200∘C. The photocatalytic degradation outcome showed 52% degradation of methylene blue at 10 ppm and 90w/m2. These results suggest the potential utility of these binary nanocomposites in photocatalytic applications for the degradation of organic pollutants. [ABSTRACT FROM AUTHOR]

Electron tunneling induced photon emission in gallium doped (1%) zinc oxide was detected by scanning tunneling microscope in ambient condition. Simultaneously acquired topography and photon maps reveal interesting correlation. Photon maps depict few intense emission spots. Existence of a threshold tunneling current (6 nA) and applied bias (1.8 V), for detectable photon emission was observed. Further analysis of the results suggests Fowler-type photon emission which is ascribed to radiative electron-hole recombination. Localized photon emission spectroscopy exhibits prominent peaks at hν=2.96, 3.43, and 3.80 eV, which match well with the results obtained from photoluminescence studies. [ABSTRACT FROM AUTHOR]

Tin oxide thin films were deposited on alumina substrates at 350°C by spray pyrolysis technique. The films were studied after annealing them in air at different temperatures 550°C, 750°C and 950°C for 30 min. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical absorption spectroscopy technique. The grain size was observed to be increased, ranging from 40 to 56.1 nm, with the increase in annealing temperature. Absorbance spectra were taken to examine the optical properties. The band gap energy was observed to be decreased with the increase in annealing temperature. These films were tested to various gases at different operating temperature ranging from 50°C to 450°C. The Tin Oxide film showed maximum sensitivity to H2S gas. The H2S sensing property of the SnO2 films was investigated with different annealing temperatures of the films and at different concentrations of H2S gas. It was found that the annealing temperature of the film significantly affects the sensitivity of the SnO2 to the H2S gas. The maximum sensitivity was found in case of the film annealed at temperature 950°C at the operating temperature 100°C. The sensitivity was found to be increased by 24% in case of the film annealed at 950°C as compared to the sensitivity of the film annealed at 550°C. The observed response of the film was for gas concentration of 10 ppm for H2S with reasonable sensitivity. The quick response and fast recovery are the main features of this film. The effect of annealing temperature on the structural, microstructural, optical and gas sensing properties of the nanocrystalline tin oxide thin films were studied and discussed. [ABSTRACT FROM AUTHOR]