Search

A method to carry out a priori simulations of pulsed-laser-induced single-event effects experiments is reported. Nonlinear optical simulations are conducted to model the 3-D distributions of charge from a laser pulse. These pulsed-laser-induced charge distributions are then incorporated into a charge transport solver to model the movement of charge as the device returns to a steady state. The output of the simulation infrastructure is a current transient from which collected charge and the temporal characteristics of the transient can be determined. This complete approach to modeling, which includes full device structure information, nonlinear optical energy deposition, and the subsequent movement of optically generated charge in a device and measurement circuit, allows for direct comparison between experimental and simulated current transients. A large-area silicon diode was used as the test vehicle, and good agreement was found between simulations and experiments in both total injected charge as well as temporal characteristics. Importantly, the a priori simulation approach does not require knowledge from prior heavy-ion testing, making it a predictive tool with broad versatility and minimal reliance on approximations. [ABSTRACT FROM AUTHOR]

Pulsed-laser-induced single-event current measurements on two geometries of waveguide-integrated germanium photodiodes were conducted over a range of operating voltages to examine the impact of photodiode geometry on the transient response. Vertical p-i-n photodiodes exhibit transients with a duration that is relatively independent of the operating voltage, while the transient duration in lateral p-i-n photodiodes depends on the operating voltage. Furthermore, the experimental measurements facilitate identification of device dimensions that impact the transient response. These results can be used to identify potential radiation mitigation strategies for photodiodes operating in a radiation environment. Understanding the implications of design choices is critical for designing integrated photonic systems that balance system performance with tolerance for radiation degradation. [ABSTRACT FROM AUTHOR]

Heavy-ion, focused X-ray, and pulsed laser single-event transient (SET) experiments are performed on a silicon epitaxial diode. Collected charge, transient rise times, and transient fall times are calculated and compared between different sources. The transient shape characteristics depend on the source (ion, X-ray, or laser), even when similar amounts of charge are generated. The observed differences are examined and explained in terms of basic charge collection mechanisms. [ABSTRACT FROM AUTHOR]

A sensitive volume is developed using pulsed laser-induced collected charge for two bias conditions in an epitaxial silicon diode. These sensitive volumes show good agreement with the experimental two-photon absorption laser-induced collected charge at a variety of focal positions and pulse energies. When compared to ion-induced collected charge, the laser-based sensitive volume overpredicts the experimental collected charge at low bias and agrees at high bias. A sensitive volume based on ion-induced collected charge adequately describes the ion experimental results at both biases. Differences in the amount of potential modulation explain the differences between the ion- and laser-based sensitive volumes at the lower bias. Truncation of potential modulation by the highly doped substrate, at the higher bias, results in similar sensitive volumes. [ABSTRACT FROM AUTHOR]

Modeling systems containing commercial-off-the-shelf (COTS) parts exposed to total ionizing dose (TID) are difficult due to large parameter variability in the parts as a function of dose. This article provides a rapid approach to predicting the system performance as a function of TID given these parameter variations. A radiation-aware model for an IRF510 power MOSFET is generated from a small population of irradiated parts, and this model is randomly sampled for each of the transistors in an example circuit, utilizing the degraded parameters. The simulations predict the circuit operating in one of three distinct modes, with circuits containing large variability in parts failing in some instances. The simulated data are compared to experimental data using a method that involves interchanging irradiated parts in a socketed printed circuit board (PCB) to produce a large number of different combinations of test circuits. The simulated data correctly predicted the circuit modes of operation, and the part-swapping technique eliminated the cost of building many test boards. [ABSTRACT FROM AUTHOR]

Pulsed, laser-induced, single-event current measurements on silicon-on-insulator (SOI) FinFETs at subbandgap wavelength (1260 nm) are affected by the polarization of the laser light used in the experimental testing setup. Such polarization dependence is not observed during pulsed laser, single-event effects testing on large-area silicon diodes, suggesting that polarization dependence arises due to the presence of the nanoscale fin. Plasmonic enhancement is proposed as a likely mechanism for the polarization effects due to the metal/dielectric interfaces in the fin region. The observed polarization dependence has ramifications for collection and interpretation of data acquired by pulsed laser testing. Device orientation of FinFETs and other nanoscale devices during pulsed laser testing should be considered in order to ensure consistent testing conditions and reproducible measurement results across multiple measurement campaigns. [ABSTRACT FROM AUTHOR]

The single-event-transient response of InGaAs FinFETs with different fin widths is examined using pulsed-laser and heavy-ion irradiation. Devices with wider fins collect more charge in both environments. Quantum-well structures confine charge collection in the channel, and determine the sensitive volume. Simulations show that the charge density produced by irradiation is similar for devices with different fin widths, but more charge is collected by wider fin devices due to the larger channel volume. Charge accumulated in the buffer and substrate layers modulates the body potential, altering the degree of back-gate control, leading to additional effects associated with charge accumulation in wider fin devices. Optical simulations for a model system suggest that optical phenomena in the fins should be considered for laser testing. These include optical interference, plasmonic enhancement at the metal–dielectric interfaces, and enhanced electron–hole pair recombination due to multiple reflections in multigate devices with nanoscale dimensions. [ABSTRACT FROM PUBLISHER]