Search

Lignocellulosic biomass is the most abundant, low-cost, bio-renewable resource that holds enormous importance as alternative source for production of biofuels and other biochemicals that can be utilized as building blocks for production of new materials. Enzymatic hydrolysis is an essential step involved in the bioconversion of lignocellulose to produce fermentable monosaccharides. However, to allow the enzymatic hydrolysis, a pretreatment step is needed in order to remove the lignin barrier and break down the crystalline structure of cellulose. The present manuscript is dedicated to reviewing the most commonly applied 'green' pretreatment processes used in bioconversion of lignocellulosic biomasses within the 'biorefinery' concept. In this frame, the effects of different pretreatment methods on lignocellulosic biomass are described along with an in-depth discussion on the benefits and drawbacks of each method, including generation of potentially inhibitory compounds for enzymatic hydrolysis, effect on cellulose digestibility, and generation of compounds toxic for the environment, and energy and economic demand. [ABSTRACT FROM AUTHOR]

The actualization of a circular economy through the use of lignocellulosic wastes as renewable resources can lead to reduce the dependence from fossil-based resources and contribute to a sustainable waste management. The integrated biorefineries, exploiting the overall lignocellulosic waste components to generate fuels, chemicals and energy, are the pillar of the circular economy. The biological treatment is receiving great attention for the biorefinery development since it is considered an eco-friendly alternative to the physico-chemical strategies to increase the biobased product recovery from wastes and improve saccharification and fermentation yields. This paper reviews the last advances in the biological treatments aimed at upgrading lignocellulosic wastes, implementing the biorefinery concept and advocating circular economy. [ABSTRACT FROM AUTHOR]

Laccases are oxidative enzymes related to the degradation of phenolic compounds, including lignin units, with concomitant reduction of oxygen to water. Delignification is a necessary pretreatment step in the process of converting plant biomass into fermentable sugars. The objective of this work was to optimize the production of laccases and to evaluate the delignification of sugarcane bagasse by Pleurotus ostreatus in solid-state fermentation. Among eight variables (pH, water activity, temperature, and concentrations of CuSO4, (NH4)2SO4, KH2PO4, asparagine, and yeast extract), copper sulfate and ammonium sulfate concentrations were demonstrated to significantly influence laccase production. The replacement of ammonium sulfate by yeast extract and the addition of ferulic acid as inducer provided increases of 5.7- and 2.0-fold, respectively, in laccase activity. Optimization of laccase production as a function of yeast extract, copper sulfate, and ferulic acid concentrations was performed by response surface methodology and optimal concentrations were 6.4 g/L, 172.6 μM, and 1.86 mM, respectively. Experimentally, the maximum laccase activity of 151.6 U/g was produced at the 5th day of solid-state fermentation. Lignin content in sugarcane bagasse was reduced from 31.89% to 26.36% after 5 days and to 20.79% after 15 days by the biological treatment of solid-state fermentation. [ABSTRACT FROM AUTHOR]

Abstract: Laccases are oxidative enzymes linked to biological degradation of lignin. The aim of this work was to evaluate the effect of inducers and different concentrations of nitrogen on production level of total laccase activity and pattern of laccase isoforms, produced in solid state fermentation of sugarcane bagasse by a selected strain of Pleurotus ostreatus. The addition of yeast extract 5g/L, copper sulfate 150μM and ferulic acid 2mM provided highest enzymatic activity (167U/g) and zymograms indicated the presence of six laccase isoforms (POXA1b, POXA3, POXC and three other isoforms). Results of protein identification by mass spectrometry confirmed the presence of POXC and POXA3 as the main isoenzymes, and also identified a glyoxal oxidase and three galactose oxidases. The fact that the isoenzyme POXA1b was not identified in the analyzed samples can be possibly explained by its sensitivity to protease degradation. [Copyright &y& Elsevier]

Abstract: Consolidated BioProcessing (CBP) can provide an important contribution to reducing ethanol production costs and moving from cellulosic feedstock to fuel ethanol tanks. Several efforts have so far been focused mainly on CBP category II engineering an ethanologen yeast or bacterium to be cellulolytic, but the limited ability of the category II CBP system for producing enzymes for lignocellulose degradation remains a challenge. As an alternative, category I CBP, aimed at engineering a cellulase producer to be ethanologenic, could be pursued, but it is still in its infancy. Some cellulolytic thermophilic bacteria have been described as potential candidates for category I CBP. However, only fungi naturally produce the needed titers of cellulases required for the complete saccharification of pretreated lignocellulose. In this review, potential of cellulolytic fungi as candidates for category I CBP is discussed. [Copyright &y& Elsevier]

Abstract: This review provides an overview of the potential of bioethanol fuel production from lignocellulosic residues in the Mediterranean Basin. Residues from cereal crops, olive trees, and tomato and grape processing are abundant lignocellulosic wastes in France, Italy, Spain, Turkey and Egypt, where their use as raw materials for ethanol production could give rise to a potential production capacity of 13Mtoe of ethanol. Due to the lack of sufficient amounts of agricultural residues in all of the other Mediterranean countries, use of the cellulosic content of municipal solid waste (MSW) as feedstock for ethanol fuel production is also proposed. A maximum potential production capacity of 30Mtoe of ethanol could be achieved from 50% of the 180million tons of waste currently produced annually in the Mediterranean Basin, the management of which has become a subject of serious concern. However, to make large-scale ethanol production from agricultural residues and MSW a medium-term feasible goal in the Mediterranean Basin, huge efforts are needed to achieve the required progress in cellulose ethanol technologies and to overcome several foreseeable constraints. [Copyright &y& Elsevier]

Laccases (benzenediol:oxygen oxidoreductases, EC 1.10.3.2) are blue multicopper oxidases that catalyze the oxidation of an array of aromatic substrates concomitantly with the reduction of molecular oxygen to water. In fungi, laccases carry out a variety of physiological roles during their life cycle. These enzymes are being increasingly evaluated for a variety of biotechnological applications due to their broad substrate range. In this review, the most recent studies on laccase structural features and catalytic mechanisms along with analyses of their expression are reported and examined with the aim of contributing to the discussion on their structure–function relationships. Attention has also been paid to the properties of enzymes endowed with unique characteristics and to fungal laccase multigene families and their organization. [ABSTRACT FROM AUTHOR]

Among the laccases produced by the white-rot fungus Pleurotus ostreatus, there are two closely related atypical isoenzymes, POXA3a and POXA3b. These isoenzymes are endowed with quaternary structure, consisting of two subunits very different in size. The POXA3 large subunit is clearly homologous to other known laccases, while the small subunit does not show significant homology with any protein in data banks. To investigate on the singular structure of the POXA3 complex, a new system for recombinant expression of heterodimer proteins in the yeast Kluyveromyces lactis has been set up. A unique expression vector has been used and the cDNAs encoding the two subunits have been cloned under the control of the same bi-directionally acting promoter. Expression of the large subunit alone and co-expression of both subunits in the same host have been demonstrated and the properties of the recombinant proteins have been compared. Clones expressing the large subunit alone exhibited always notably lower activity than those expressing both subunits. In addition to the activity increase, the presence of the small subunit led to a significant increase of laccase stability. Therefore, a role of the small subunit in POXA3 stabilisation is suggested. [ABSTRACT FROM AUTHOR]

Pleurotus ostreatus produces several extracellular proteases which are believed to be involved in the regulation of the ligninolytic activities of this fungus. Recently, purification and characterization of the most abundant P. ostreatus extracellular protease (PoSl) have been reported. The sequence of the posi gene and of the corresponding cDNA has been determined, allowing the identification of its pre- and pro-sequences. A mature protein sequence has been verified by mass spectrometry mapping, the N-glycosylation sites have been identified and the glycosidic moieties characterized. Mature PoSI shows a cleaved peptide bond in the C-terminal region, which remains associated with the catalytic domain in a non-covalent complex. Reported results indicate that this enzyme is involved in the activation of other P. ostreatus secreted proteases, thus suggesting its leading role in cascade activation mechanisms. Analyses of the PoSI sequence by homology search resulted in the identification of a DNA sequence encoding a new protease, homologous to PoSl, in the Phanerochaete chrysosporium genome. A new subgroup of subtilisin-like proteases, belonging to the pyrolysin family, has been defined, which includes proteases from ascomycete and basidiomycete fungi. [ABSTRACT FROM AUTHOR]

Fungal laccase gene transcription is strongly induced by copper ions; notably, some laccase promoters contain multiple putative metal-responsive elements (MREs). Previously, it has been demonstrated that the Pleurotus ostreatus laccase genes poxc and poxa 1b are transcriptionally induced by copper, and several putative MREs were found in the promoter regions of these genes, which extend for about 400 nt upstream of the start codon (ATG). Identification of MRE sequences, which are protected by protein binding in the poxc and poxa1b promoter regions, has been achieved by footprinting analyses. Electromobility shift assays led to the evaluation of the ability of the identified MREs to bind protein(s), and the role of specific nucleotides of these elements in complex formation has also been analysed. The formation of complexes between analysed MREs and fungal proteins requires the absence of metal ions. Proteins extracted from fungus grown in copper-depleted medium are able to form complexes with MREs, whilst proteins extracted from fungus grown in copper-containing medium are able to form complexes only in the presence of a metal chelator. Moreover, copper-depleted proteins are unable to form complexes when copper or zinc ions are added. UV-cross-linking analyses led to the determination of the molecular masses of the MRE-binding proteins. In the poxa1b promoter, a GC-rich region, homologous to the core binding site for transcription factor Sp1, decreases the binding affinity of the adjacent MRE, affecting its interactions with fungal protein factors. [ABSTRACT FROM AUTHOR]

The chemical syntheses currently employed for industrial purposes, including in the manufacture of cosmetics, present limitations such as unwanted side reactions and the need for harsh chemical reaction conditions. In order to overcome these drawbacks, novel enzymes are developed to catalyze the targeted bioconversions. In the present study, a methodology for the construction and the automated screening of evolved variants library of a Type B feruloyl esterase from Myceliophthora thermophila (MtFae1a) was developed and applied to generation of 30,000 mutants and their screening for selecting the variants with higher activity than the wild-type enzyme. The library was generated by error-prone PCR of mtfae1a cDNA and expressed in Saccharomyces cerevisiae. Screening for extracellular enzymatic activity towards 4-nitrocatechol-1-yl ferulate, a new substrate developed ad hoc for high-throughput assays of feruloyl esterases, led to the selection of 30 improved enzyme variants. The best four variants and the wild-type MtFae1a were investigated in docking experiments with hydroxycinnamic acid esters using a model of 3D structure of MtFae1a. These variants were also used as biocatalysts in transesterification reactions leading to different target products in detergentless microemulsions and showed enhanced synthetic activities, although the screening strategy had been based on improved hydrolytic activity. [ABSTRACT FROM AUTHOR]

The world economy is moving toward the use of renewable and nonedible lignocellulosic biomasses as substitutes for fossil sources in order to decrease the environmental impact of manufacturing processes and overcome the conflict with food production. Enzymatic hydrolysis of the feedstock is a key technology for bio-based chemical production, and the identification of novel, less expensive and more efficient biocatalysts is one of the main challenges. As the genomic era has shown that only a few microorganisms can be cultured under standard laboratory conditions, the extraction and analysis of genetic material directly from environmental samples, termed metagenomics, is a promising way to overcome this bottleneck. Two screening methodologies can be used on metagenomic material: the function-driven approach of expression libraries and sequence-driven analysis based on gene homology. Both techniques have been shown to be useful for the discovery of novel biocatalysts for lignocellulose conversion, and they enabled identification of several (hemi)cellulases and accessory enzymes involved in (hemi)cellulose hydrolysis. This review summarizes the latest progress in metagenomics aimed at discovering new enzymes for lignocellulose saccharification. [ABSTRACT FROM PUBLISHER]

Highlights: [•] Around 7000 variants of an α-l-arabinofuranosidase were prepared by error prone PCR. [•] The four selected variants showed the same aminoacidic substitutions F435Y/Y446F. [•] The variant F435Y/Y446F was overproduced in Pichia pastoris and purified and characterized. [•] The variant F435Y/Y446F showed a k cat 3 fold higher than the wild-type towards p-NPA. [•] The variant is able to hydrolyze larch arabinogalactan not recognized by the wild type. [Copyright &y& Elsevier]

Fossil fuel reserves depletion, global warming, unrelenting population growth, and costly and problematic waste recycling call for renewable resources of energy and consumer products. As an alternative to the 100 % oil economy, production processes based on biomass can be developed. Huge amounts of lignocellulosic wastes are yearly produced all around the world. They include agricultural residues, food farming wastes, 'green-grocer's wastes,' tree pruning residues, and organic and paper fraction of urban solid wastes. The common ways currently adopted for disposal of these wastes present environmental and economic disadvantages. As an alternative, processes for adding value to wastes producing high added products should be developed, that is the upgrading concept: adding value to wastes by production of a product with desired reproducible properties, having economic and ecological advantages. A wide range of high added value products, such as enzymes, biofuels, organic acids, biopolymers, bioelectricity, and molecules for food and pharmaceutical industries, can be obtained by upgrading solid wastes. The most recent advancements of their production by biotechnological processes are overviewed in this manuscript. [ABSTRACT FROM AUTHOR]

In silico analyses of several laccase promoter sequences have shown the presence of many different responsive elements differentially distributed along the promoter sequences. Analysis of Pleurotus ostreatus laccase promoter poxa1b extending around 1400-bp upstream of the start codon showed the presence of several putative response elements, such as 10 metal-responsive elements. Development of a system for in vivo analysis of P. ostreatus laccase promoter poxa1b by enhanced green fluorescent protein expression was carried out, based on a polyethylene glycol-mediated procedure for fungal transformation. Quantitative measurement of fluorescence expressed in P. ostreatus transformants grown in the presence and in the absence of copper sulfate was performed, demonstrating an increase in expression level induced by the metal. [ABSTRACT FROM AUTHOR]

Abstract: Conversion of lignocellulosic materials to useful, high value products normally requires a pre-treatment step to transform or deconstruct the recalcitrant and heterogeneous lignin fraction. The development of “green tools” for the transformation of lignocellulosic feedstocks is in high demand for a sustainable exploitation of such resources. This multi-faceted challenge is being addressed by an ever-increasing suite of ligninolytic enzymes isolated from various sources. Among these, fungal laccases are known to play an important role in lignin degradation/modification processes. The white-rot fungus Pleurotus ostreatus expresses multiple laccase genes encoding isoenzymes with different properties. The availability of established recombinant expression systems for P. ostreatus laccase isoenzymes has allowed to further enrich the panel of P. ostreatus laccases by the construction of mutated, “better performing” enzymes through molecular evolution techniques. New oxidative catalysts with improved activity and stability either at high temperature and at acidic and alkaline pH have been isolated and characterized. [Copyright &y& Elsevier]

The subfamily of POXA3 laccase isoenzymes produced by the fungus Pleurotus ostreatus has been characterized as an example of the complexity and heterogeneity of fungal isoenzyme patterns. Two isoenzymes, POXA3a and POXA3b, were previously purified, exhibiting an unusual heterodimeric structure composed of a large (67 kDa) and a small (18 or 16 kDa) subunit. A unique gene encodes the large subunit of both POXA3a and POXA3b, but alternative splicing produces two variants—differing for an insertion of four amino acids—for each isoenzyme. Two genes encoding POXA3a and POXA3b small subunits have been identified, and the corresponding amino acid sequences show only two amino acid substitutions. The 18- and 16-kDa subunits of both POXA3a and POXA3b differ for N-glycosylation at Asn150 of the 16-kDa subunit. The POXA3 large subunit 3D model allows us to highlight peculiarities of this molecule with respect to the laccases whose 3D structures are known. [ABSTRACT FROM AUTHOR]

Two strictly related laccase isoenzymes (POXA3a and POXA3b), produced by Pleurotus ostreatus in copper supplemented cultures, have been purified and characterised. Both the native proteins were found to be constituted by a large subunit (67 kDa) and a small subunit (18 or 16 kDa). Peptide mapping of the 18 and 16 kDa polypeptides from POXA3a and POXA3b suggests the identity of the 18 kDa subunits and the generation of the 16 kDa polypeptides from the 18 kDa ones. Structural data on POXA3a and POXA3b do not allow ascertaining significant differences between the two isoenzymes. On the other hand, dissociation of POXA3a complex is observed in 3 M urea, whilst POXA3b complex is not dissociated even in 6 M urea. Evidences are reported on the role played by extracellular proteases in the activation of these isoenzymes. The sequence of a unique gene and of the corresponding cDNA, encoding the 67 kDa POXA3 subunit, has been determined. [Copyright &y& Elsevier]

With the aim to reach the maximum recovery of bulk and specialty bioproducts while minimizing waste generation, a multi-product biorefinery for ethanol and lactic acid production from the biomass of cyanobacterium Arthrospira platensis was investigated. Therefore, the residual biomass resulting from different pretreatments consisting of supercritical fluid extraction (SF) and microwave assisted extraction with non-polar (MN) and polar solvents (MP), previously applied on A. platensis to extract bioactive metabolites, was further valorized. In particular, it was used as a substrate for fermentation with Saccharomyces cerevisiae LPB-287 and Lactobacillus acidophilus ATCC 43121 to produce bioethanol (BE) and lactic acid (LA), respectively. The maximum concentrations achieved were 3.02 ± 0.07 g/L of BE by the MN process at 120 rpm 30 °C, and 9.67 ± 0.05 g/L of LA by the SF process at 120 rpm 37 °C. An economic analysis of BE and LA production was carried out to elucidate the impact of fermentation scale, fermenter costs, production titer, fermentation time and cyanobacterial biomass production cost. The results indicated that the critical variables are fermenter scale, equipment cost, and product titer; time process was analyzed but was not critical. As scale increased, costs tended to stabilize, but also more product was generated, which causes production costs per unit of product to sharply decrease. The median value of production cost was US$ 1.27 and US$ 0.39, for BE and LA, respectively, supporting the concept of cyanobacterium biomass being used for fermentation and subsequent extraction to obtain ethanol and lactic acid as end products from A. platensis. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • A library of around 30,000 random mutants of FoFaeC was generated. • Screening for enzymatic activity led to the selection of 96 improved variants. • The best five mutants were characterized for their substrate specificity. • Small molecule docking simulations were applied to the selected variants. Abstract The need to develop competitive and eco-friendly processes in the cosmetic industry leads to the search for new enzymes with improved properties for industrial bioconversions in this sector. In the present study, a complete methodology to generate, express and screen diversity for the type C feruloyl esterase from Fusarium oxysporium FoFaeC was set up in a high-throughput fashion. A library of around 30,000 random mutants of FoFaeC was generated by error prone PCR of fofaec cDNA and expressed in Yarrowia lipolytica. Screening for enzymatic activity towards the substrates 5-bromo-4-chloroindol-3-yl and 4-nitrocatechol-1-yl ferulates allowed the selection of 96 enzyme variants endowed with improved enzymatic activity that were then characterized for thermo- and solvent- tolerance. The five best mutants in terms of higher activity, thermo- and solvent- tolerance were selected for analysis of substrate specificity. Variant L432I was shown to be able to hydrolyze all the tested substrates, except methyl sinapate, with higher activity than wild type FoFaeC towards methyl p -coumarate, methyl ferulate and methyl caffeate. Moreover, the E455D variant was found to maintain completely its hydrolytic activity after two hour incubation at 55 °C, whereas the L284Q/V405I variant showed both higher thermo- and solvent- tolerance than wild type FoFaeC. Small molecule docking simulations were applied to the five novel selected variants in order to examine the binding pattern of substrates used for enzyme characterization of wild type FoFaeC and the evolved variants. [ABSTRACT FROM AUTHOR]

The enzymatic extracellular mixtures of two new microorganisms – Streptomyces flavogriseus AE64X and AE63X – isolated from Eucalyptus camaldulensis and Populus nigra and producing cellulase and xylanase, were characterized and applied to hydrolysis of pretreated Arundo donax , Populus nigra and Panicum virgatum (10% w/v) replacing the commercial enzymes Accelerase 1500 and Accelerase XY (5.4 and 145 U/g of pretreated biomass, respectively). It is worth of noting that the newly developed extracellular enzymatic mixtures, without any purification step and at the same dosage, presented saccharification yields that are higher (86% for S. flavogriseus AE64X) than those of commercial enzymes (81%). Moreover, these enzymatic mixes allowed us to hydrolyse both cellulose and xylan within the different lignocellulose biomasses substituting both the cellulase and xylanase of commercial source. The produced sugars were also fermentable by Basfia succiniciproducens BPP7 into succinic acid with high yield. [ABSTRACT FROM AUTHOR]

The type C feruloyl esterase FoFaeC from Fusarium oxysporum is a newly discovered enzyme with high potential for use in the hydrolysis of lignocellulosic biomass but it shows low activity towards sinapates. In this work, small molecule docking simulations were employed in order to identify important residues for the binding of the four model methyl esters of hydroxycinnamic acids, methyl ferulate/caffeate/sinapate/p-coumarate, to the predicted structure of FoFaeC. Subsequently rational redesign was applied to the enzyme’ active site in order to improve its specificity towards methyl sinapate. A double mutation (F230H/T202V) was considered to provide hydrophobic environment for stabilization of the methoxy substitution on sinapate and a larger binding pocket. Five mutant clones and the wild type were produced in Pichia pastoris and biochemically characterized. All clones showed improved activity, substrate affinity, catalytic efficiency and turnover rate compared to the wild type against methyl sinapate, with clone P13 showing a 5-fold improvement in catalytic efficiency. Although the affinity of all mutant clones was improved against the four model substrates, the catalytic efficiency and turnover rate decreased for the substrates containing a hydroxyl substitution. [ABSTRACT FROM AUTHOR]

Feruloyl esterases (FAEs) are a diverse group of enzymes that specifically catalyze the hydrolysis of ester bonds between a hydroxycinnamic (e.g. ferulic) acid and plant poly- or oligosaccharides. FAEs as auxiliary enzymes significantly assist xylanolytic and pectinolytic enzymes in gaining access to their site of action during biomass saccharification for biofuel and biochemical production. A limited number of FAEs have been functionally characterized compared to over 1000 putative fungal FAEs that were recently predicted by similarity-based genome mining, which divided phylogenetically into different subfamilies (SFs). In this study, 27 putative and six characterized FAEs from both ascomycete and basidiomycete fungi were selected and heterologously expressed in Pichia pastoris and the recombinant proteins biochemically characterized to validate the previous genome mining and phylogenetical grouping and to expand the information on activity of fungal FAEs. As a result, 20 enzymes were shown to possess FAE activity, being active towards p NP-ferulate and/or methyl hydroxycinnamate substrates, and covering 11 subfamilies. Most of the new FAEs showed activities comparable to those of previously characterized fungal FAEs. [ABSTRACT FROM AUTHOR]

A novel fungal species able to synthesize enzymes with potential synergistic actions in lignocellulose conversion was isolated from the biomass of Arundo donax during biodegradation under natural conditions in the Gussone Park of the Royal Palace of Portici (Naples, Italy). In this work, this species was subjected to morphological and phylogenetic analyses. Sequencing of its genome was performed, resulting in 28 scaffolds that were assembled into 27.05 Mb containing 9744 predicted genes, among which 396 belong to carbohydrate-active enzyme (CAZyme)-encoding genes. Here we describe and illustrate this previously unknown species, which was named Talaromyces borbonicus, by a polyphasic approach combining phenotypic, physiological, and sequence data. [ABSTRACT FROM AUTHOR]

The feruloyl esterases FaeA1, FaeA2, FaeB1, FaeB2 from Myceliophthora thermophila C1 and MtFae1a from M. thermophila ATCC 42464 were used as biocatalysts for the transesterification of vinyl ferulate (VFA) with l -arabinose in detergentless microemulsions. The effect of parameters such as the microemulsion composition, the substrate concentration, the enzyme load, the pH, the temperature and the agitation was investigated. FaeA1 offered the highest transesterification yield (52.2 ± 4.3%) after 8 h of incubation at 50 °C using 80 mM VFA, 55 mM l -arabinose and 0.02 mg FAE mL −1 in a mixture comprising of 19.8: 74.7: 5.5 v/v/v n -hexane: t -butanol: 100 mM MOPS-NaOH pH 8.0. The ability of l -arabinose ferulate (AFA) to scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH) radicals was significant (IC 50 386.5 μM). AFA was not cytotoxic even at high concentrations (1 mM) however was found to be pro-oxidant at concentrations higher than 20 μM when the antioxidant activity was determined with the dichloro-dihydro-fluorescein diacetate (DCFH-DA) assay in human skin fibroblasts. [ABSTRACT FROM AUTHOR]

4- O -Methyl- d -glucuronic acid (MeGlcA) is a side-residue of glucuronoarabinoxylan and can form ester linkages to lignin, contributing significantly to the strength and rigidity of the plant cell wall. Glucuronoyl esterases (4- O -methyl-glucuronoyl methylesterases, GEs) can cleave this ester bond, and therefore may play a significant role as auxiliary enzymes in biomass saccharification for the production of biofuels and biochemicals. GEs belong to a relatively new family of carbohydrate esterases (CE15) in the CAZy database ( www.cazy.org ), and so far around ten fungal GEs have been characterized. To explore additional GE enzymes, we used a genome mining strategy. BLAST analysis with characterized GEs against approximately 250 publicly accessible fungal genomes identified more than 150 putative fungal GEs, which were classified into eight phylogenetic sub-groups. To validate the genome mining strategy, 21 selected GEs from both ascomycete and basidiomycete fungi were heterologously produced in Pichia pastoris . Of these enzymes, 18 were active against benzyl d -glucuronate demonstrating the suitability of our genome mining strategy for enzyme discovery. [ABSTRACT FROM AUTHOR]

One of the major ecological concerns associated with biodiesel production is the generation of waste/crude glycerol during the trans-esterification process. Purification of this crude glycerol is not economically viable. In this context, the development of an efficient and economically viable strategy would be biotransformation reactions converting the biodiesel derived crude glycerol into value added chemicals. Hence the process ensures the sustainability and waste management in biodiesel industry, paving a path to integrated biorefineries. This review addresses a waste to wealth approach for utilization of crude glycerol in the production of value added chemicals, current trends, challenges, future perspectives, metabolic approaches and the genetic tools developed for the improved synthesis over wild type microorganisms were described. [ABSTRACT FROM AUTHOR]

Arundo donax was used to investigate the effect of the enzyme and substrate concentrations on hydrolysis, pre-hydrolysis and simultaneous saccharification and fermentation (PSSF), in comparison to simultaneous saccharification and fermentation (SSF). Hydrolysis was performed at 37 and 50 °C. At the highest biomass (10%) and enzyme (69.6 FPU/g cellulose) loadings, the highest glucose concentration (32.4 g/L) was obtained (at 50 °C). SSF resulted in a cellulose conversion (91.9%) and an ethanol concentration (19.8 g/L) higher than what was obtained using PSSF at 37 °C (86.9% and 18.8 g/L, respectively) and PSSF at 50 °C (81.6% and 17.7 g/L, respectively). A positive correlation between the cellulase concentration, cellulose conversion, and ethanol content was observed. In PSSF, the increase in the solids loadings caused a reduction in the % cellulose conversion, but the ethanol concentration in PSSF and SSF increased. SSF appeared to be the most advantageous process for bioethanol production from A. donax. [ABSTRACT FROM AUTHOR]

Bio-based succinic acid production from lignocellulosic biomass is one of the attractive and prominent alternative technologies to overcome issues associated with the utilization of fossil sources. In this context, it is necessary to find new microorganisms that are able to efficiently ferment this recalcitrant feedstock. The ecological approach developed in this study enabled the isolation of Basfia succiniciproducens BPP7 from a complex rumen ecosystem. This new wild-type strain was able to synthesize up to 6.06 ± 0.05 g/L of succinate (corresponding to 0.84 ± 0.017 g of succinate per gram of consumed glucose + xylose and to 0.14 ± 0.001 g of succinate per gram of glucans + xylans present in the biomass before hydrolysis) from Arundo donax hydrolysate in separate hydrolysis and fermentation (SHF) experiments. Higher titers of succinic acid were obtained through the optimization of growth conditions. The optimal medium composition identified on the smaller scale was then used for 2.5-L batch experiments, which used A. donax hydrolysate and yeast extract as the main C and N sources, respectively. A maximal titer of 9.4 ± 0.4 g/L of succinic acid was obtained after 24 h. The overall results clearly demonstrate the potential of B. succiniciproducens BPP7 for succinate production. [ABSTRACT FROM AUTHOR]

Five feruloyl esterases (FAEs; EC 3.1.1.73), FaeA1, FaeA2, FaeB1, and FaeB2 from Myceliophthora thermophila C1 and MtFae1a from M. thermophila ATCC 42464, were tested for their ability to catalyze the transesterification of vinyl ferulate (VFA) with prenol in detergentless microemulsions. Reaction conditions were optimized investigating parameters such as the medium composition, the substrate concentration, the enzyme load, the pH, the temperature, and agitation. FaeB2 offered the highest transesterification yield (71.5 ± 0.2%) after 24 h of incubation at 30 °C using 60 mM VFA, 1 M prenol, and 0.02 mg FAE/mL in a mixture comprising of 53.4:43.4:3.2 v/ v/ v n-hexane: t-butanol:100 mM MOPS-NaOH, pH 6.0. At these conditions, the competitive side hydrolysis of VFA was 4.7-fold minimized. The ability of prenyl ferulate (PFA) and its corresponding ferulic acid (FA) to scavenge 1,1-diphenyl-2-picrylhydrazyl (DPPH) radicals was significant and similar (IC 423.39 μM for PFA, 329.9 μM for FA). PFA was not cytotoxic at 0.8-100 μM (IC 220.23 μM) and reduced intracellular reactive oxygen species (ROS) in human skin fibroblasts at concentrations ranging between 4 and 20 μM as determined with the dichloro-dihydro-fluorescein diacetate (DCFH-DA) assay. [ABSTRACT FROM AUTHOR]

Water hyacinth a fresh water aquatic plant is considered as a noxious weed in many parts of the world since it grows very fast and depletes nutrients and oxygen from water bodies adversely affecting the growth of both plants and animals. Hence conversion of this problematic weed to value added chemicals and fuels helps in the self-sustainability especially for developing countries. The present review discusses the various value added products and fuels which can be produced from water hyacinth, the recent research and developmental activities on the bioconversion of water hyacinth for the production of fuels and value added products as well as its possibilities and challenges in commercialization. [ABSTRACT FROM AUTHOR]

In the present work the recently isolated strain Basfia succiniciproducens BPP7 was evaluated for the production of succinic acid up to the pilot fermentation scale in separate hydrolysis and fermentation experiments on Arundo donax , a non-food dedicated energy crop. An average concentration of about 17 g/L of succinic acid and a yield on consumed sugars of 0.75 mol/mol were obtained demonstrating strain potential for further process improvement. Small scale experiments indicated that the concentration of acetic acid in the medium is crucial to improve productivity; on the other hand, interestingly, short-term (24 h) adaptation to higher acetic acid concentrations, and strain recovery, were also observed. [ABSTRACT FROM AUTHOR]

Cosmeceuticals are cosmetic products containing biologically active ingredients purporting to offer a pharmaceutical therapeutic benefit. The active ingredients can be extracted and purified from natural sources (botanicals, herbal extracts, or animals) but can also be obtained biotechnologically by fermentation and cell cultures or by enzymatic synthesis and modification of natural compounds. A cosmeceutical ingredient should possess an attractive property such as anti-oxidant, anti-inflammatory, skin whitening, anti-aging, anti-wrinkling, or photoprotective activity, among others. During the past years, there has been an increased interest on the enzymatic synthesis of bioactive esters and glycosides based on (trans)esterification, (trans)glycosylation, or oxidation reactions. Natural bioactive compounds with exceptional theurapeutic properties and low toxicity may offer a new insight into the design and development of potent and beneficial cosmetics. This review gives an overview of the enzymatic modifications which are performed currently for the synthesis of products with attractive properties for the cosmeceutical industry. [ABSTRACT FROM AUTHOR]

Bio-based organic acids are an eco-friendly alternative to petroleumderived products. In this work, the production of organic chemicals was investigated for the first time in the Cosenzaea myxofaciens species using hydrolysed lignocellulosic biomass from Arundo donax. The strain C. myxofaciens BPM1, isolated from bovine rumen, was able to produce a high amount of lactic acid, followed by acetic and succinic acids in synthetic substrate in microaerophilic and anaerobic conditions. When hydrolysed lignocellulosic biomass from Arundo donax supplemented with several nitrogen sources was used as substrate in separate hydrolysis and fermentation in anaerobic conditions, a significant increase in organic acids was recovered, reaching values up to 12.13 ± 0.17, 1.68 ± 0.1, and 5.23 ± 0.04 g L-1 of lactate, succinate, and acetate, respectively. Moreover, the strain C. myxofaciens BPM1 was capable of synthesizing a small amount of ethanol, with a resulting concentration ranging from 0.67 ± 0.05 to 1.46 ± 0.03 g L-1. This work shows that the strain C. myxofaciens BPM1 is a potential source of interesting bio-based chemicals for a wide range of industrial applications. In addition, the inexpensive fermentation process using A. donax hydrolysate and corn steep liquor as carbon and nitrogen sources could be suitable for economical and efficient production of succinic acid in industrial processes. [ABSTRACT FROM AUTHOR]

This study reports enzymatic hydrolysis of the biomass of the giant reed ( Arundo donax L.) after ammonia fibre expansion (AFEX) pretreatment. In particular, the capacity of the arabinofuranosidase from the fungus Pleurotus ostreatus recombinantly expressed in Pichia pastoris rPoAbf, its evolved mutant rPoAbf F435Y/Y446F and the endo-cellulase from Streptomyces sp. G12 CelStrep recombinantly expressed in Escherichia coli to enhance the hydrolysis of AFEX-treated A. donax was investigated, using the corn stover as reference feedstock. The investigated enzymes were assayed using a mixture of purified cellulases (CBHI, CBHII, EGI and βG), endoxylanases (LX3, LX4) and accessory hemicellulases (LarbF and LβX) as reference enzyme mixture and substituting EGI with rCelStrep and LarbF with rPoAbf or rPoAbf F435Y/Y446F. The use of rPoAbf F435Y/Y446F in the substitution of LarbF led to improvements in sugar conversion, giving a glucan, xylan and arabinan conversion after 72 h of around 62, 63 and 80 %, respectively, similar or higher than those (44, 66 and 55 %) achieved by 72 h hydrolysis with commercial enzymes Novozymes Cellic®, Ctec3 and Htec3. The enzymes rPoAbf, rPoAbf F435Y/Y446F and rCelStrep were also investigated for their effect on hydrolysis of AFEX-pretreated A. donax by addition to commercial enzyme mixture Novozymes Cellic®, Ctec3 and Htec3, and it was shown that the addition of rPoAbf and its evolved mutant rPoAbf F435Y/Y446F enhanced both xylan and arabinan conversions, which achieved 80 % after 6 days of saccharification with rPoAbf F435Y/Y446F. [ABSTRACT FROM AUTHOR]

Lignocellulosic biomasses derived from dedicated crops and agro-industrial residual materials are promising renewable resources for the production of fuels and other added value bioproducts. Due to the tolerance to a wide range of environments, the dedicated crops can be cultivated on marginal lands, avoiding conflict with food production and having beneficial effects on the environment. Besides, the agro-industrial residual materials represent an abundant, available, and cheap source of bioproducts that completely cut out the economical and environmental issues related to the cultivation of energy crops. Different processing steps like pretreatment, hydrolysis and microbial fermentation are needed to convert biomass into added value bioproducts. The reactor configuration, the operative conditions, and the operation mode of the conversion processes are crucial parameters for a high yield and productivity of the biomass bioconversion process. This review summarizes the last progresses in the bioreactor field, with main attention on the new configurations and the agitation systems, for conversion of dedicated energy crops ( Arundo donax) and residual materials (corn stover, wheat straw, mesquite wood, agave bagasse, fruit and citrus peel wastes, sunflower seed hull, switchgrass, poplar sawdust, cogon grass, sugarcane bagasse, sunflower seed hull, and poplar wood) into sugars and ethanol. The main novelty of this review is its focus on reactor components and properties. [ABSTRACT FROM AUTHOR]

Six Lactobacillus strains were analyzed to select a bacterium for conversion of brewers’ spent grain (BSG) into lactic acid. Among the investigated strains, L. acidophilus ATCC 43121 showed the highest yield of lactic acid production (16.1 g/L after 48 hours) when grown in a synthetic medium. It was then analyzed for its ability to grow on the hydrolysates obtained from BSG after acid-alkaline (AAT) or aqueous ammonia soaking (AAS) pretreatment. The lactic acid production by L. acidophilus ATCC 43121 through fermentation of the hydrolysate from AAS treated BSG was 96% higher than that from the AAT treated one, although similar yields of lactic acid per consumed glucose were achieved due to a higher (46%) glucose consumption by L. acidophilus ATCC 43121 in the AAS BSG hydrolysate. It is worth noting that adding yeast extract to the BSG hydrolysates increased both the yield of lactic acid per substrate consumed and the volumetric productivity. The best results were obtained by fermentation of AAS BSG hydrolysate supplemented by yeast extract, in which the strain produced 22.16 g/L of lactic acid (yield of 0.61 g/g), 27% higher than the value (17.49 g/L) obtained in the absence of a nitrogen source. [ABSTRACT FROM AUTHOR]

An enzymatic mixture of cellulases and xylanases was produced by Pleurotus ostreatus using microcrystalline cellulose as inducer, partially characterized and tested in the statistical analysis of Arundo donax bioconversion. The Plackett-Burman screening design was applied to identify the most significant parameters for the enzymatic hydrolysis of pretreated A. donax. As the most significant influence during the enzymatic hydrolysis of A. donax was exercised by the temperature (°C), pH, and time, the combined effect of these factors in the bioconversion by P. ostreatus cellulase and xylanase was analyzed by a 33 factorial experimental design. It is worth noting that the best result of 480.10 mg of sugars/gds, obtained at 45°C, pH 3.5, and 96 hours of incubation, was significant also when compared with the results previously reached by process optimization with commercial enzymes. [ABSTRACT FROM AUTHOR]

In this study, the recombinant α-L-arabinofuranosidase from the fungus Pleurotus ostreatus (rPoAbf) was subjected to site-directed mutagenesis with the aim of elucidating the role of glycosylation on the properties of the enzyme at the level of S160 residue. As a matter of fact, previous mass spectral analyses had led to the localization of a single O-glycosylation at this site. Recombinant expression and characterization of the rPoAbf mutant S160G was therefore performed. It was shown that the catalytic properties are slightly changed by the mutation, with a more evident modification of the Kcat and KM toward the synthetic substrate pN-glucopyranoside. More importantly, the mutation negatively affected the stability of the enzyme at various pHs and temperatures. Circular dichroism (CD) analyses showed a minimum at 210 nm for wild-type (wt) rPoAbf, typical of the beta-sheets structure, whereas this minimum is shifted for rPoAbf S160G, suggesting the presence of an unfolded structure. A similar behavior was revealed when wt rPoAbf was enzymatically deglycosylated. CD structural analyses of both the site-directed mutant and the enzymatically deglycosylated wild-type enzyme indicate a role of the glycosylation at the S160 residue in rPoAbf secondary structure stability. [ABSTRACT FROM AUTHOR]

The aims of this study were to evaluate the microbial diversity of different lignocellulosic biomasses during degradation under natural conditions and to isolate, select, characterise new well-adapted bacterial strains to detect potentially improved enzyme-producing bacteria. The microbiota of biomass piles of Arundo donax, Eucalyptus camaldulensis and Populus nigra were evaluated by high-throughput sequencing. A highly complex bacterial community was found, composed of ubiquitous bacteria, with the highest representation by the Actinobacteria, Proteobacteria, Bacteroidetes and Firmicutes phyla. The abundances of the major and minor taxa retrieved during the process were determined by the selective pressure produced by the lignocellulosic plant species and degradation conditions. Moreover, cellulolytic bacteria were isolated using differential substrates and screened for cellulase, cellobiase, xylanase, pectinase and ligninase activities. Forty strains that showed multienzymatic activity were selected and identified. The highest endo-cellulase activity was seen in Promicromonospora sukumoe CE86 and Isoptericola variabilis CA84, which were able to degrade cellulose, cellobiose and xylan. Sixty-two percent of bacterial strains tested exhibited high extracellular endo-1,4-ß-glucanase activity in liquid media. These approaches show that the microbiota of lignocellulosic biomasses can be considered an important source of bacterial strains to upgrade the feasibility of lignocellulose conversion for the 'greener' technology of second-generation biofuels. [ABSTRACT FROM AUTHOR]

Ethanol production from lignocellulosic biomasses raises a global interest because it represents a good alternative to petroleum-derived energies and reduces the food versus fuel conflict generated by first generation ethanol. In this study, alkaline-acid pretreated brewers' spent grain (BSG) was evaluated for ethanol production after enzymatic hydrolysis with commercial enzymes. The obtained hydrolysate containing a glucose concentration of 75 g/L was adopted, after dilution up to 50 g/L, for fermentation by the strain Saccharomyces cerevisiae NRRL YB 2293 selected as the best producer among five ethanologenic microorganims. When the hydrolysate was supplemented with yeast extract, 12.79 g/L of ethanol, corresponding to 0.28 g of ethanol per grams of glucose consumed (55% efficiency), was obtained within 24 h, while in the non-supplemented hydrolysate, a similar concentration was reached within 48 h. The volumetric productivity increased from 0.25 g/L.h in the un-supplemented hydrolysate to 0.53 g/L h in the yeast extract supplemented hydrolysate. In conclusion, the strain S. cerevisiae NRRL YB 2293 was shown able to produce ethanol from BSG. Although an equal amount of ethanol was reached in both BSG hydrolysate media, the nitrogen source supplementation reduced the ethanol fermentation time and promoted glucose uptake and cell growth. [ABSTRACT FROM AUTHOR]

This manuscript describes the analysis of xylanase production by Aspergillus niger NRRL 328 in solid state fermentation (SSF) of soybean husks. A maximum value of extracellular xylanase activity of approximately 950 U g-1 was achieved after 96 h. Proteomic analyses performed on the enzymatic mixture responsible for the maximum value of xylanase activity in SSF revealed the presence of two xylanases. This xylanolytic mixture was partially purified and characterized. It followed Michaelis-Menten kinetics towards xylan, with a KM of 7.92 ±0.97 mg xylan/mL and a Vmax of 262.2 ± 27.8 g L-1 s-1. The optimum pH for the enzyme is 5.3, and the optimal temperature is 50 °C. The enzyme retains 100% of its activity at 40 °C for at least 1 month. It shows very high stability in a broad pH range, with a half-life of 40 days at pH 5.3, pH 6.0, pH 6.5, pH 7.0, and pH 8.0. [ABSTRACT FROM AUTHOR]

The fungal arabinofuranosidase from Pleurotus ostreatus PoAbf recombinantly expressed in Pichia pastoris rPoAbf and its evolved variant rPoAbf F435Y/Y446F were tested for their effectiveness to enhance the enzymatic saccharification of three lignocellulosic biomasses, namely Arundo donax , corn cobs and brewer’s spent grains (BSG), after chemical or chemical–physical pretreatment. All the raw materials were subjected to an alkaline pretreatment by soaking in aqueous ammonia solution whilst the biomass from A. donax was also pretreated by steam explosion. The capability of the wild-type and mutant rPoAbf to increase the fermentable sugars recovery was assessed by using these enzymes in combination with different (hemi)cellulolytic activities. These enzymatic mixtures were either entirely of commercial origin or contained the cellulase from Streptomyces sp. G12 CelStrep recombinantly expressed in Escherichia coli in substitution to the commercial counterparts. The addition of the arabinofuranosidases from P. ostreatus improved the hydrolytic efficiency of the commercial enzymatic cocktails on all the pretreated biomasses. The best results were obtained using the rPoAbf evolved variant and are represented by increases of the xylose recovery up to 56.4%. These data clearly highlight the important role of the accessory hemicellulolytic activities to optimize the xylan bioconversion yields. [ABSTRACT FROM AUTHOR]

Pectinolytic enzymes play an important role in the processing of lignocellulosic materials because of their ability to improve the access of cellulases to their substrate by removing pectins. The strain Paenibacillus xylanolyticus 2-6L3 was isolated from mature compost obtained from agroindustrial wastes, and the enzyme pectate lyase from P. xylanolyticus 2- 6L3, named PaenxylPel, was partially purified and subjected to structural and functional characterisation. The enzyme exhibited an optimum temperature between 60 and 70 °C and optimal pH value of 9.0 for its pectinase activity on pectin from citrus fruit. PaenxylPel showed a thermoresistance and pH resistance higher than those of other pectate lyases so far described, with half-lives of 48 and 24 h at 60 and 70 °C, respectively, a retention of around 80% of activity after 96 h at 40 and 50 °C, and a half-life of about 15 days at pH 8.0. PaenxylPel followed Michaelis-Menten kinetics toward pectin from citrus fruit, pectin from sugar beet pulp, high-ester pectin extracted from citrus peel (> 50% esterified), and polygalacturonic acid (PLA). The ability to act on both PLA and highly methylated pectins, together with a double peak in the graph of optimum pH at pH 5 and 9, suggest that pectate lyase from P. xylanolyticus shows an unusual activity, combining traits of pectate lyase and pectin lyase. This is the first manuscript on the pectinolytic activity of P. xylanolyticus. [ABSTRACT FROM AUTHOR]

This manuscript describes the analysis of the effect of cellulose, carboxymethylcellulose (CMC), xylan, and xylose as inducers of cellulase and xylanase activity production by Ganoderma applanatum MR-56 and the optimization of their production in liquid cultures by statistical methods. The Plackett-Burman screening design was applied to identify the most significant inducers of xylanase and cellulase activities production by G. applanatum MR-56. The most significant effect on xylanase and cellulase activities production was exercised by cellulose, even if xylose and CMC were also effective at some times. The combined effect of cellulose, yeast extract, and pH was analyzed by a 2³ factorial experimental design with four central points that showed that the maximum tested cellulose (1 % w/v) and yeast extract (5 g L-1) concentrations gave the maximum production of xylanase (8.24 U mL-1) and cellulase (3.29 U mL-1) activity at pH 6 and 4, respectively. These values achieved for cellulase and xylanase activity represent 12-25 fold and 36 fold higher values than the maximum so far reported for other strains of G. applanatum, respectively. [ABSTRACT FROM AUTHOR]

Conversion of cellulose into fermentable sugars for ethanol production is currently performed by enzymatic hydrolysis catalyzed by cellulases. The cellulases are produced by a wide variety of microorganisms, playing a major role in the recycling of biomass. The endo-1,4-ß-glucanase (CelB31C) from Bacillus amyloliquefaciens B31C, isolated from compost and previously selected on the basis of highest cellulase activity levels among Bacillus isolated, was characterized as being a potential candidate for a biocatalyst in lignocellulose conversion for secondgeneration bioethanol production. The aim of this work was to evaluate the changes in production of enzymatic activity of the endo-1,4-ß- glucanase (CelB31C) and the expression of its gene (bglC) using a carboxymethylcellulase activity assay and qRT-PCR analysis, respectively, during growth of B. amyloliquefaciens B31C on different cellulose sources: carboxymethylcellulose (CMC), pure cellulose from Arundo donax, pretreated Arundo donax biomass (Chemtex), and microcrystalline cellulose (Avicel). The results showed that both the expression of bglC gene and the enzymatic activity production are related to the type of cellulose source. The strain showed a high enzymatic activity on lignocellulosic biomass and on microcrystalline cellulose. Furthermore, the highest gene expression occurred during the exponential phase of growth, except in the presence of Avicel. [ABSTRACT FROM AUTHOR]

Ninety bacteria isolated from raw composting materials were screened for their cellulolytic activity on solid medium containing carboxymethylcellulose. The bacteria producing the highest cellulolytic activity levels were identified by 16 S r RNA sequencing as Bacillus licheniformis strain 1, Bacillus subtilis subsp. subtilis strain B7 B, Bacillus subtilis subsp. spizizenii strain 6, and Bacillus amyloliquefaciens strain B31 C. Cellulase activity production by the most productive strain B. amyloliquefaciens B31 C was optimized in liquid culture varying the carbon source. Comparison of growth curves of B. amyloliquefaciens B31 C at temperatures from 28 to 47 °C indicated its thermotolerant nature. Moreover, analysis of time courses of cellulase activity production in this thermal range showed that increase of temperature from 28 to 37 °C causes an increase of cellulase activity levels. Investigating the enzymes responsible for cellulase activity produced by B. amyloliquefaciens B31 C by proteomic analyses, an endoglucanase was identified. It was shown that the purified enzyme catalyzes carboxymethylcellulose's hydrolysis following Michaelis- Menten kinetics with a KM of 9.95 mg ml−1 and a vmax of 284 μM min−1. It shows a retention of 90% of its activity for at least 144 h of incubation at 40 °C and exhibits a range of optimum temperatures from 50 to 70 °C. [ABSTRACT FROM AUTHOR]

The genome of the white rot basidiomycete Pleurotus ostreatus includes 12 phenol oxidase (laccase) genes. In this study, we examined their expression profiles in different fungal strains under different culture conditions (submerged and solid cultures) and in the presence of a wheat straw extract, which was used as an inducer of the laccase gene family. We used a reverse transcription-quantitative PCR (RT-qPCR)-based approach and focused on determining the reaction parameters (in particular, the reference gene set for the normalization and reaction efficiency determinations) used to achieve an accurate estimation of the relative gene expression values. The results suggested that (i) laccase gene transcription is upregulated in the induced submerged fermentation (iSmF) cultures but downregulated in the solid fermentation (SSF) cultures, (ii) the Lacc2 and Lacc10 genes are the main sources of laccase activity in the iSmF cultures upon induction with water-soluble wheat straw extracts, and (iii) an additional, as-yet-uncharacterized activity (Unk1) is specifically induced in SSF cultures that complements the activity of Lacc2 and Lacc10. Moreover, both the enzymatic laccase activities and the Lacc gene family transcription profiles greatly differ between closely related strains. These differences can be targeted for biotechnological breeding programs for enzyme production in submerged fermentation reactors. [ABSTRACT FROM AUTHOR]

An α- l-arabinofuranosidase produced by Pleurotus ostreatus (PoAbf) during solid state fermentation on tomato pomace was identified and the corresponding gene and cDNA were cloned and sequenced. Molecular analysis showed that the poabf gene carries 26 exons interrupted by 25 introns and has an open reading frame encoding a protein of 646 amino acid residues, including a signal peptide of 20 amino acid residues. The amino acid sequence similar to the other α- l-arabinofuranosidases indicated that the enzyme encoded by poabf can be classified as a family 51 glycoside hydrolase. Heterologous recombinant expression of PoAbf was carried out in the yeasts Pichia pastoris and Kluyveromyces lactis achieving the highest production level of the secreted enzyme (180 mg L) in the former host. rPoAbf produced in P. pastoris was purified and characterized. It is a glycosylated monomer with a molecular weight of 81,500 Da in denaturing conditions. Mass spectral analyses led to the localization of a single O-glycosylation site at the level of Ser160. The enzyme is highly specific for α- l-arabinofuranosyl linkages and when assayed with p-nitrophenyl α- l-arabinofuranoside it follows Michaelis-Menten kinetics with a K of 0.64 mM and a k of 3,010 min. The optimum pH is 5 and the optimal temperature 40°C. It is worth noting that the enzyme shows a very high stability in a broad range of pH. The more durable activity showed by rPoAbf in comparison to the other α- l-arabinofuranosidases enhances its potential for biotechnological applications and increases interest in elucidating the molecular bases of its peculiar properties. [ABSTRACT FROM AUTHOR]

Background: The use of lignocellulosic materials for second generation ethanol production would give several advantages such as minimizing the conflict between land use for food and fuel production, providing less expensive raw materials than conventional agricultural feedstock, allowing lower greenhouse gas emissions than those of first generation ethanol. However, cellulosic biofuels are not produced at a competitive level yet, mainly because of the high production costs of the cellulolytic enzymes. Therefore, this study was aimed at discovering new cellulolytic microorganisms and enzymes. Results: Different bacteria isolated from raw composting materials obtained from vegetable processing industry wastes were screened for their cellulolytic activity on solid medium containing carboxymethylcellulose. Four strains belonging to the actinomycetes group were selected on the basis of their phenotypic traits and cellulolytic activity on solid medium containing carboxymethylcellulose. The strain showing the highest cellulolytic activity was identified by 16S rRNA sequencing as belonging to Streptomyces genus and it was designated as Streptomyces sp. strain G12. Investigating the enzymes responsible for cellulase activity produced by Streptomyces G12 by proteomic analyses, two endoglucanases were identified. Gene coding for one of these enzymes, named CelStrep, was cloned and sequenced. Molecular analysis showed that the celstrep gene has an open reading frame encoding a protein of 379 amino acid residues, including a signal peptide of 37 amino acid residues. Comparison of deduced aminoacidic sequence to the other cellulases indicated that the enzyme CelStrep can be classified as a family 12 glycoside hydrolase. Heterologous recombinant expression of CelStrep was carried out in Escherichia coli, and the active recombinant enzyme was purified from culture supernatant and characterized. It catalyzes the hydrolysis of carboxymethylcellulose following a Michaelis-Menten kinetics with a KM of 9.13 mg/ml and a vmax of 3469 µM min-1. The enzyme exhibits a half life of around 24 h and 96 h at 60°C and 50°C, respectively and shows a retention of around 80% of activity after 96 h at 40°C. Conclusions: In this manuscript, we describe the isolation of a new cellulolytic strain, Streptomyces sp. G12, from industrial waste based compost, the identification of the enzymes putatively responsible for its cellulolytic activity, the cloning and the recombinant expression of the gene coding for the Streptomyces sp. G12 cellulase CelStrep, that was characterized showing to exhibit a relevant thermoresistance increasing its potential for cellulose conversion. [ABSTRACT FROM AUTHOR]