Search

Single‐atom catalysts (SACs) supported on inorganic materials have attracted much attention in numerous research fields for their high catalytic performance. However, such SACs have been limited by the low metal loading, especially on different types of inorganic supports. Herein, a general approach is presented for preparing SACs on metallic, metal oxide, and perovskite nanosheet (NS) supports to reach a high metal loading of up to 3.94 wt%, by utilizing N‐doped graphene as a sacrificial template that spatially confines the single atoms (SAs). Specifically, the target support material precursors are adsorbed onto the SAs‐stabilized sacrificial template, followed by subsequent heat treatment to transfer the SAs to the support material and to remove the graphene layer. Pt SAs on oxide support exhibits little to no aggregation throughout >10 000 min of annealing at 275 °C, demonstrating high thermal stability, as also supported by ex situ post‐anneal electron microscopy and X‐ray absorption fine structure studies. As a proof‐of‐concept, Pt SACs on SnO2 NSs exhibit high catalytic activity toward chemiresistive sensing of acetone gas (response = 95.4 at 10 ppm, 7.6‐fold enhancement compared with pristine SnO2 NSs) and unprecedented stability under highly humid conditions (27.4% response deterioration at 95% relative humidity). [ABSTRACT FROM AUTHOR]

Single‐atom catalysts (SACs) supported on inorganic materials have attracted much attention in numerous research fields for their high catalytic performance. However, such SACs have been limited by the low metal loading, especially on different types of inorganic supports. Herein, a general approach is presented for preparing SACs on metallic, metal oxide, and perovskite nanosheet (NS) supports to reach a high metal loading of up to 3.94 wt%, by utilizing N‐doped graphene as a sacrificial template that spatially confines the single atoms (SAs). Specifically, the target support material precursors are adsorbed onto the SAs‐stabilized sacrificial template, followed by subsequent heat treatment to transfer the SAs to the support material and to remove the graphene layer. Pt SAs on oxide support exhibits little to no aggregation throughout >10 000 min of annealing at 275 °C, demonstrating high thermal stability, as also supported by ex situ post‐anneal electron microscopy and X‐ray absorption fine structure studies. As a proof‐of‐concept, Pt SACs on SnO2 NSs exhibit high catalytic activity toward chemiresistive sensing of acetone gas (response = 95.4 at 10 ppm, 7.6‐fold enhancement compared with pristine SnO2 NSs) and unprecedented stability under highly humid conditions (27.4% response deterioration at 95% relative humidity). [ABSTRACT FROM AUTHOR]

Electrospinning–etching strategy was employed to synthesize Pt-loaded SnO 2 hollow microbelts (Pt_SnO 2 HBLs) based chemiresistive-type sensor demonstrating high sensitivity and selectivity toward acetone gas. This strategy overcomes a major hurdle toward achieving ubiquitous gas diffusion in electrospun structures, and provides highly porous thin-walled HBLs with large surface area and small crystallites. [Display omitted] • In situ templating of SnO 2 with SiO 2 was employed to form Pt-loaded SiO 2 @SnO 2 core–shell microbelts. • Etching away of SiO 2 in the Pt-loaded SiO 2 @SnO 2 microbelts yielded Pt-loaded SnO 2 hollow microbelts. • The Pt-loaded SnO 2 hollow microbelts exhibited good response (R a /R g = 93.5) and selectivity toward 2 ppm acetone at 350 °C. Challenges for ubiquitous diffusion of gas analytes into semiconducting metal oxides (SMOs) based sensing layers have necessitated the introduction of unprecedented synthesis techniques for thin, porous and high-performance gas sensing materials. In this work, electrospinning and calcination were employed to prepare unprecedented SiO 2 –SnO 2 core–shell microbelts (hereinafter referred to as SiO 2 @SnO 2 BLs) followed by etching away of SiO 2 in NaOH solution (pH 12) to achieve hollow SnO 2 BLs (hereinafter referred to as SnO 2 HBLs) with mean crystal size of 14.01 nm, large BET surface area (143.5 m2‧g–1), high porosity (mean pore size of 5.7 nm), and shell thickness of 58.3 ± 11.4 nm. Sensitization of SnO 2 HBLs with apoferritin-templated platinum nanoparticles (Pt NPs) enhanced their detection capability toward acetone. Response (defined as R a /R g , where R a and R g are sensor resistances in air and target gas, respectively) of Pt(0.12 %)_SnO 2 HBLs toward 2 ppm acetone was up to 7.8 times higher compared to that of pristine SnO 2 HBLs, and exhibited faster response (9.2 s). The Pt(0.12 %)_SnO 2 HBLs based sensor indicated a promising long-term stability, and outstanding repeatability of response (R a /R g = 93.7 ± 0.89) toward 25 cycles of 2 ppm acetone exposure in a humid environment of 90 % relative humidity. This performance could be attributed to the unique morphology of HBLs, sensitization effects of catalytic Pt NPs, and enlargement of the electron-depleted layer resulting from a Schottky barrier between Pt NPs and SnO 2 grains. [ABSTRACT FROM AUTHOR]