Search

The PWM voltage pulses output by the inverter reaches the stator winding of the wind turbine generator through the cable. Due to the impedance mismatch between the motor and the cable, the voltage at the motor end rises under the action of the circuit wave process; on the other hand, electromagnetic oscillation occurs within the motor winding. Higher overvoltage is generated under the combined effect of both, which greatly accelerates the aging and breakdown of the insulation layer of the permanent magnet synchronous wind turbine. In this paper, a three-dimensional electromagnetic model of the permanent magnet synchronous wind turbine generator is established. The distribution circuit parameters of the stator winding of the permanent magnet machine are calculated using the finite element method, and its circuit model is based. The voltage distribution of the stator winding under different PWM excitations is investigated by simulation software, and the effects of the time of the rising edge and the pulse width of the PWM pulse on the stator winding voltage to ground and the turn-to-turn voltage distribution are studied. The results show that the effect of the rising edge time is larger when the rising edge time is shorter, the maximum voltage to ground occurs in the first coil, and the amplitude can be up to 1.5 times of the output voltage. When the rising edge time is longer, the maximum voltage to ground occurs in the end coil, and the amplitude is slightly higher than the output voltage. The trend of turn-to-turn voltage variation is similar for different rising edges; only the maximum turn-to-turn voltage amplitude is different. Pulse width has a small effect on overvoltage and only occurs when the pulse width is less than 10 μs. The research results of this paper are of great significance in revealing the aging and breakdown mechanism of the generator stator insulation, as well as the insulation coordination and design. [ABSTRACT FROM AUTHOR]

Three-phase linear synchronous actuators play a pivotal role in precision motion control applications such as lithography machines and laser material processing stages. Achieving superior tracking performance is paramount in the design of motion control systems, prompting the utilization of advanced control algorithms. In this study, a novel approach is presented to enhance the tracking capability of a three-phase permanent magnet actuator by introducing a predictive field-oriented control system. The primary contribution of this paper lies in the comprehensive design and implementation of the predictive field-oriented control system. Initially, actuator modeling is conducted in the rotating reference frame (d–q frame) and finite element analysis is performed to determine key electrical quantities, including magnetic flux densities and inductances. To address the challenges posed by time-varying sinusoidal electrical signals, a field-oriented control methodology is proposed. Notably, the novelty of this work is underscored by a distinct emphasis on the predictive control strategy employed in the system. The predictive controller is implemented on a 32-bit ARM Cortex microcontroller, showcasing the practical viability of the proposed approach. Experimental results substantiate the effectiveness of the proposed method in achieving precise trajectory tracking. This paper contributes to the field by providing a rigorous analysis of a three-phase permanent magnet actuator and introducing a predictive field-oriented control system. The methodology outlined here enhances tracking capabilities and signifies a substantial advancement in the broader landscape of precision motion control systems. Thus, this work adds valuable insights to the existing body of knowledge in the domain, while offering a notable contribution to the field. [ABSTRACT FROM AUTHOR]

Permanent magnet-assisted synchronous reluctance motor (PMSRM) has been widely used in many fields due to their advantages of less permanent magnets and low cost. However, the permanent magnet torque and reluctance torque of the traditional PMSRM reach their maximum values at different current angles. Therefore, the utilization ratio of the total torque to each torque component is low, which leads to the low power density of the PMSRM. To solve this problem, a new rotor structure suitable for PMSRM is proposed in this paper. The rotor can improve the total torque by increasing the maximum value of permanent magnet torque and the utilization rate of total torque to each torque component. Thus, the power density of the motor is effectively improved. In order to realize the matching design of each parameter in the proposed rotor structure, the Taguchi method is used to optimize the design, and the influence of each optimization variable on torque and torque ripple is analyzed. The finite element simulation analysis method is used to establish the electromagnetic simulation model of the traditional structure, the new structure proposed and the optimized structure of the new structure by Maxwell simulation software. The simulation results show that the proposed new rotor structure not only effectively improves the torque density, but also effectively reduces the torque ripple. [ABSTRACT FROM AUTHOR]

The critical speed of eddy current braking is a vital parameter in the design of eddy current braking devices. Currently, most simulations and experiments are used to determine the critical speed, which means a lot of time costs. This paper presents two laws of critical speed variation to help designers more quickly determine the critical speed of a particular eddy current braking device. At first, the structure and the critical speed principle of permanent magnet rotary eddy current brake (PMRECB) are described. Secondly, the finite element analysis is used to verify the accuracy of the two laws. Finally, the validity of the finite element model is confirmed by the eddy current braking test. [ABSTRACT FROM AUTHOR]

This paper proposes a novel consequent‐pole dual‐stator linear permanent magnet vernier machine (DS‐LPMVM) with PM in the mover slot opening, which has a bi‐directional flux modulation effect. The novelty of the proposed machine consists of consequent‐pole double‐sided topology with toroidal windings placed in the mover slot, as well as PMs both on the stator and mover slot to improve the air gap magnetic field. The dual‐stator adopts misalignment structure to suppress detent force and produce steady thrust. The electromagnetic parameters of the proposed DS‐LPMVM are evaluated and quantitatively compared with the conventional linear permanent magnet vernier machine (C‐LPMVM) in terms of air‐gap flux density, no‐load back EMF, inductance, and thrust. The geometrical parameters are designed to reduce the detent force. By analyzing the optimized structure parameters of the two machines, the good electromagnetic performances of the proposed machine are verified by the finite element method (FEM) and semi‐analytical method, and both results of the two methods are basically the same. It is found that the amount of PMs for the proposed machine is reduced by 20% compared to the C‐LPMVM, but the average thrust is increased by 20.7% and the thrust ripple is reduced to 4.04%. The results show that the proposed DS‐LPMVM has better flux modulation effect and thrust characteristics than C‐LPMCM. Finally, a 12‐slot, 10‐pole pairs prototype was manufactured and tested. © 2024 Institute of Electrical Engineers of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Net zero and electrification targets are continuing to enforce a need for the development of high-performance electrical machines, increasingly based on the use of rare earth permanent magnets. Biased flux motors have the potential to overcome some of the disadvantages associated with more conventional electrical machines. Since their introduction, there has been a consistent trend towards new and improved topologies, all relying on the same principles of operation. In this paper, a new alternative operation is proposed where the magnetic flux density offset of each module is different. The resulting asymmetric biased excitations of the magnets leads to a flux concentration in the air gap. Placement of magnets in the slot-opening area is shown to produce a higher average torque at a higher power factor. It is mathematically shown that the conventional methods used to investigate the effect of each group of magnets separately cannot be used for the explanation of this operation principle. Therefore, it is necessary to simultaneously consider both groups of magnets in the magnetic equivalent circuit. Due to the use of magnets in these motors, thermal conditions are also investigated. Finally, a comprehensive comparison between several stator-situated-magnet motors is presented. The performance of the proposed motor is improved in terms of average torque, torque density, PM torque density, power factor, and overload capability. The torque density specifically has increased by 9%. Moreover, both motors have suitable thermal behaviour which confirms the validity of the demagnetization analysis. [ABSTRACT FROM AUTHOR]

A novel asymmetric interior permanent magnet (AIPM) machine is proposed in this paper. The machine's rotor consists of asymmetric poles and auxiliary flux barriers. The torque ripple of the machine is weakened by the asymmetric design of the left and right sides of the magnetic poles. The magnetic‐field‐shifting (MFS) effect improves the electromagnetic torque after adding the auxiliary flux barrier to shift the magnetic axis. The influence of critical geometrical parameters on the electromagnetic performance of the machine is investigated under the condition that the stator and permanent magnet volume remain unchanged. The relevant geometrical parameters of the machine are optimized and designed through the improved Taguchi method. The performance of the AIPM machine and the conventional machine under no‐load and load conditions are further compared by simulation analysis with finite elements, verifying the increase in electromagnetic torque and the reduction in torque ripple. © 2024 Institute of Electrical Engineers of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

The axial flux permanent magnet (AFPM) machines with the parallel magnetic circuit (PMC) rotor can effectively improve its torque density. The PMC rotor consists of two sub‐rotors, radial Halbach array permanent magnet (PM) and tangential PM. The magnetic fields generated by two sub‐rotors are not in the same 2‐D analytical planes. In this paper, an equivalent analytical model of PMC‐AFPM machines is proposed to solve this problem. The radial Halbach array PM rotor is equated to the axial Halbach array PM rotor based on the equivalent transformation principle. The exact subdomain models of equivalent axial Halbach array PM rotor and tangential PM rotor are built respectively and then superimposed to obtain the magnetic field distribution. The electromagnetic characteristics of the PMC‐AFPM machine under no‐load and load conditions are calculated by the proposed analytical model and compared with calculations of the finite element model (FEM). The results verify the accuracy of the equivalent analytical model. The comparative analysis of the AFPM machines with PMC rotor and tangential PM rotor verifies the advantage of PMC rotor configuration to improve the torque density. © 2024 Institute of Electrical Engineer of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

The permanent magnet claw pole machine (PMCPM) with soft magnetic composite (SMC) cores has shown better performance than the traditional transverse flux machine, and its performance can be improved by developing its stator with hybrid silicon sheet and SMC cores, and this kind of PMCPM is named as HPMCPM. Due to its complex 3D magnetic structure, analyzing its performance by using the traditional finite element method (FEM) is time-consuming. To overcome this constraint, this paper proposes a magneto-electric-thermal coupling network (METCN) model with bidirectional data transmission to calculate the electromagnetic performance and temperature distribution and the calculation results are verified by the FEM method and experimental measurement results. Compared with the 3D FEM, the proposed METCN method has the advantage of fast calculation speed and similar accuracy. [ABSTRACT FROM AUTHOR]

In this paper, three typical permanent magnet machines for All-Electric aircraft propulsion are designed, optimized and compared. Firstly, the necessary performances are determined based on the requirements of high power/torque density and an aircraft with a maximum takeoff weight of 1500 kg. The initial structures of interior permanent magnet (IPM) synchronous machine, vernier permanent magnet (VPM) machine and flux-switching permanent magnet (FSPM) machine are designed with identical stator outer radius and rotor shaft length. Then, parametric sensitivity analysis and multi-objective particle swarm are combined as an optimization methodology to optimize these machines. Based on the finite element analysis, the electromagnetic performances such as no-load airgap flux density harmonic spectrum, cogging torque, average output torque, losses, efficiency and power factor, etc., are generally compared and analyzed. Subsequently, the discussions are carried out, where the strength and weakness of these three machines are concluded and the future prospects are suggested. Finally, it is concluded that if effective measures are implemented to reduce the permanent magnet eddy current loss and improve the power factor, the VPM machine would be the most suitable choice among these machines for All-Electric aircraft propulsion. [ABSTRACT FROM AUTHOR]

In this paper, a new axial-type magnetic gear with an auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AMGs, it has a higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of the proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterparts in RMGs, the AFS-AMG achieves a small size. Then, the geometrical parameters of the AFS-AMG are optimized to obtain better electromagnetic performance, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume. [ABSTRACT FROM AUTHOR]

By designing stator teeth using grain-oriented sheets (GO) and other parts still with non-grain-oriented sheets (NGO), the electromagnetic performance of the interior permanent magnet synchronous machine (GO-IPMSM) can be improved greatly. As the stator core of the designed GO-IPMSM is a hybrid core that is composed of two different silicon sheets, both the electromagnetic and mechanical performances are affected by the stator joint shape between GO and NGO sheets. Meanwhile, with the adoption of GO, the torque ripple of GO-IPMSM is increased though the average torque is increased as well. For reducing the torque ripple, optimizing the rotor barrier shape is an effective way. In this paper, the piecewise linear interpolation method is employed for establishing the stator joint shape between GO and NGO sheets, and the polynomial method is proposed to establish the rotor barrier shape. Through the analysis, it can be seen that the stator joint shape plays a strong role in affecting the mechanical performance of the GO-IPMSM, while the effect on the electromagnetic performance is weak. The genetic algorithm is used to optimize the rotor barrier shape for achieving high average torque and low torque ripple. Lastly, a quick and accurate efficiency map calculation method based on the Kriging model is proposed for GO-IPMSM with less finite element method (FEM) samples are required. [ABSTRACT FROM AUTHOR]

Permanent magnet synchronous motors (PMSMs) have a scale of applications linking to the industrial machines. As these machines often work in a wide temperature range, the PMSM quality consistency is threatened by the temperature fluctuate. In fact, at the start of the production of the PMSMs, the quality consistency distribution already exist due to the manufacturing dispersion. However, traditional experiment‐based consistency analysis method is inadequate for the PMSM, due to its inevitable destructive measurement for the magnetic properties. To deal with the problem, this paper proposed a model‐based quality consistency analysis method. In this paper, mechanism analysis of the temperature influence on PMSMs is carried out by the finite element analysis and the digital modeling method, so that the impact of dispersion can be depicted by model rather than destructive measurement. The relationship between the temperature and PMSM cogging torque as well as other features is quantitatively revealed. To obtain the NdFeB temperature coefficient, magnetic samples were prepared and measured. Then, the temperature characteristics of the sensitive components of PMSM are established, and the PMSM temperature characteristics can be simulated by integrating temperature coefficients into the PMSM digital model. The qualitative and quantitative temperature characteristics of cogging torque are verified by experiments with a batch of PMSMs. [ABSTRACT FROM AUTHOR]

This paper presents the efficiency improvement of a pole-changing vernier machine (PCVM) by considering the residual magnetic flux density ( B r ) of low coercivity force (LCF) permanent magnets (PMs). The PCVM operates in two modes: vernier machine (VM) mode and permanent magnet synchronous machine (PMSM) mode, achieved through pole-changing. Pole-changing involves reversing the magnetic flux direction of LCF PM to alter the number of rotor pole pairs. By changing the number of rotor pole pairs, the PCVM operates as a VM mode at low speeds, providing high torque, and as a PMSM mode at high speeds, offering high efficiency. To achieve this, a combination of high coercivity force (HCF) PM and LCF PM is utilized in a single structure. The magnetic flux direction in the LCF PM is determined by B r , and the highest efficiency is achieved when B r reaches its maximum value | B r m |. This paper focuses on improving efficiency by obtaining B r m in VM mode and − B r m in PMSM mode through the design process. Additionally, finite element analysis (FEA) is employed to compare the performance of the improved model, which considers B r , with that of the conventional model, designed without considering B r . The improved model achieves higher B r values in each mode compared to the conventional model, resulting in increased torque density. Consequently, this leads to improved efficiency. [ABSTRACT FROM AUTHOR]

The ironless linear permanent magnet synchronous motor (ILPMSM) is highly compact, easy to control, and exhibits minimal thrust fluctuations, making it an ideal choice for direct loading applications requiring precise positioning accuracy in linear motor test rigs. To address the issue of temperature rise resulting from increased primary winding current and to simultaneously enhance thrust density while minimizing thrust fluctuations, this paper introduces a bilateral-type ILPMSM with a cooling water jacket integrated between the dual-layer windings of the primary movers. The primary winding of the motor adopts a dual-layer coreless structure where the upper and lower windings are closely spaced and cooled by a non-conductive metal cooling water jacket, while the dual-sided secondary employs a Halbach permanent magnet array. The motor's overall braking force is a combination of the electromagnetic braking force generated by the energized windings and the eddy current braking force induced on the cooling water jacket. This paper specifically focuses on the analysis of the eddy current braking force. Initially, the motor's geometry and working principle are presented. Subsequently, the equivalent magnetization intensity method is employed to determine the no-load air gap magnetic density resulting from the Halbach array. An analytical model is then developed to derive expressions for the eddy current density and braking force induced in the water-cooling jacket. The accuracy of the analytical method is validated through finite element analysis. Then, a comparative analysis of the braking forces in two primary cooling structures, namely the inter-cooled type and the two-side cooled type ILPMSM, is conducted. Moreover, the characteristics of the eddy current braking force are thoroughly examined concerning motor size parameters and operating conditions. This paper provides a solid theoretical foundation for the subsequent optimization design of the proposed motor. [ABSTRACT FROM AUTHOR]

This paper presents the results of a comprehensive investigation into the comparative analysis and design optimization of ferrite-based surface permanent magnet vernier machines (SPMVMs). While SPMVMs boast a simple mechanical structure and enhanced torque density attributed to the flux modulation effect, they suffer from a persistent challenge of low power factor. Several factors hinder the adoption of low-cost ferrite magnets in SPMVMs. First, ferrite magnets are prone to irreversible demagnetization, constraining the allowable range of magnet thickness. Second, the reduced residual magnetic flux density of ferrite magnets exacerbates the decrease in power factor and machine efficiency. Thus, achieving optimal performance in ferrite-based SPMVMs necessitates the careful selection of various design parameters. To address these issues, this study employs a surrogate-based metaheuristic optimization algorithm with adaptive sampling to identify the optimal solution. Additionally, the integration of a Halbach array is explored to further enhance the performance of the three-slot/two-pole SPMVM topology. Subsequently, two ferrite-based SPMVM baseline models—one with a conventional SPM structure and another with a Halbach magnet array—are thoroughly designed, optimized, and subjected to detailed performance analysis using the 2D finite element method. [ABSTRACT FROM AUTHOR]

In this paper is presented a two-dimension analytical model for linear permanent magnet inner armature double-sided synchronous motors (LPMIADSSMs). The flux density in all areas of the proposed machine is calculated based on the sub-domain method. According to this method, the machine areas are divided into eleven sub-regions such as first external, first mover, first PM, first air gap, first winding, stator, second winding, second air gap, second PM, second external and second mover, which sign as FE, FR, FP, FAG, FW, S, SW, SAG, SP, SE and SR. To find the flux density equations, it is mandatory to solve the extracted Maxwell equations and apply the boundary conditions between each two sub-regions, which lead to find the unknown coefficients for flux density in each sub-region. In addition, the influences of magnetization patterns, i.e., parallel, ideal Hal Bach, 2-segment Halbach and bar magnet in the shifting direction of the flux distribution and armature reaction (AR), are investigated. To validate the obtained results, the proposed model results are compared with those obtained from finite element method (FEM) and Maxwell software. [ABSTRACT FROM AUTHOR]

This paper presents a two-dimensional analytical model for brushless double-rotor flux-switching permanent magnet machines (BDRPFSPMM) with yokeless stator recognized as a type of partitioned-structure flux-switching permanent magnet that is an appropriate machine to be employed as the electric motor in industry. The most salient advantages of the proposed machine are low iron loss due to volume of iron in stator and high space of stator slot for winding. The radial and tangential components of the magnetic flux density due to permanent magnets and armature currents in each active domain of the machine, electromagnetic torque, self- and mutual inductance, unbalanced magnetic force (UMF), and local traction are calculated based on the subdomain method. Teethes on both rotor and stator structures are effective on magnetic quantities, so interactions of rotor and stator saliency are considered. The method is general for the magnetic field calculation with any combination of rotor- and stator-pole number. To validate the proposed model, the analytical outputs are compared with those obtained from the finite element method (FEM). [ABSTRACT FROM AUTHOR]

In order to reduce the cogging torque of a symmetrical V-type line-start permanent magnet synchronous (LSPMS) motor, this paper proposes a multi-objective optimization method based on the combination of design parameter stratification and response surface methodology (RSM). The optimal solution to the RSM model is acquired using the max–min ant algorithm. The permanent magnet width, pole opening angle, stator slot width, rotor axial length, and rotor tooth width are selected as optimization variables. The cogging torque and average torque are the optimization objectives. Finite element method (FEM) results show that the cogging torque is reduced by 71.5%, the torque ripple is reduced by 65.6%, and the average torque is improved by 12%. Finally, the effectiveness of the algorithm is verified with simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes an analytical model of the double-stator spoke-type permanent magnet vernier machine (DSSTVM) using the subdomain method (SDM), which can be used to calculate the magnetic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the corresponding magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM. [ABSTRACT FROM AUTHOR]

In this paper, an electromagnetic analysis method is proposed to improve force characteristics by using spring permanent magnets (PMs) along the axial and circumferential directions of a linear oscillatory generator (LOG). For accurate electromagnetic analysis, a detailed analysis model of the LOG is developed, and the governing equations of each subdomain are derived based on Maxwell's equations and electromagnetic theory. Analytical solutions of the magnetic vector potential in each subdomain are derived using boundary conditions. The reliability of the proposed method is verified through a comparison with the results of a two-dimensional finite element analysis (FEA). In particular, the force characteristics depending on the spring PM is effectively derived by considering the three-dimensional (3D) circumferential and axial end effects. The proposed analysis method is used to determine the thickness of spring PM that transforms the detent force of the LOG with the spring PM into restoring force. The reliability of the proposed analysis method is verified through comparison with the results of a 3D FEA. [ABSTRACT FROM AUTHOR]

This paper introduces a technique aimed at improving the performance of an interior permanent magnet synchronous machine (IPMSM) by reducing torque ripple and radial force harmonics. Unlike conventional IPMSMs, the proposed method employs a variable airgap length that is defined by a mathematical function. Two distinct rotor shapes are investigated to determine the most efficient design. Finite Element Analysis is employed to assess both the electromagnetic and mechanical attributes of the proposed motors. It compares the results for three operating points of the shaped motor with those of a conventional one. The investigation delves into the influence of rotor geometry on key output parameters, including Back Electromotive Force (back‐EMF) harmonics, average torque, cogging torque, torque ripple, efficiency, power factor, and radial force harmonics. The findings indicate that optimising rotor shape can significantly enhance IPMSM performance by reducing torque ripples and radial force harmonics, while simultaneously increasing average torque and efficiency at different operating points. [ABSTRACT FROM AUTHOR]

In this paper, a pole-changing (PC) flux reversal permanent magnet (FRPM) motor is proposed for obtaining a wide speed range. According to the general air-gap field modulation theory, the permanent magnet (PM) magnetic field is modulated into a series of harmonics with different pole numbers by rotor teeth. By introducing an especial PM arrangement, two groups of working harmonics with different pole-pair numbers are generated in the proposed 12-7 PC-FRPM motor due to the modulation of rotor teeth. Based on the calculated slot pitch angles of these harmonics, two winding connections can be obtained for PC operation to achieve two operating modes. The electromagnetic performance of PC-FRPM motor before and after PC are analyzed using finite element analysis and verified by the experimental test results. [ABSTRACT FROM AUTHOR]

The permanent magnet electrodynamic suspension (PMEDS) owns the promising application prospect, due to its simple structure, low cost and reliable load capacity. However, the underdamping of the PMEDS system is still a challenge in engineering applications of transportation. This paper proposes a passive damping method and its implementation structure to improve the underdamping characteristics. This method utilizes the inherent magnetic leakage of on-board magnets technically. The principle of passive damping and its implementation structure is introduced in detail. And the kinetic models of ordinary and improved structure are established based on the topology graph. Besides, the magnetic field and the electromagnetic force involved in the kinetic models are analyzed, and the numerical analysis method of the drag force is verified by the high-speed test rig. Furthermore, the performance of passive damping is verified by finite element method (FEM) and the time-domain response analysis. The results show that the improved damping structure can effectively suppress vibration and improve the dynamic stability of the PMEDS system. It is beneficial to the engineering application of the PMEDS in the future. [ABSTRACT FROM AUTHOR]

This research paper represents the estimation and reduction of eddy current loss in a Magnetic Fault Current Limiter (MFCL). The nonlinear model of the device is established using electromagnetic coupled circuit supported by Finite Element Model. The current limiting performance of the MFCL is investigated by simulation study as well as laboratory testing. It is further observed that a significant amount of eddy current loss takes place inside the core and permanent magnet of the device. Different methods (shorting ring, lamination of permanent magnet and variation of magnet length) are proposed to reduce the eddy current. The advantages and disadvantages of these methods are discussed. Some design modifications are also proposed to minimize the temperature rise caused by the eddy current. [ABSTRACT FROM AUTHOR]

Axial flux permanent magnet motors have attracted increasing attention due to their compact topology and high torque density. Many topological variations have arisen over time; however, limited research has directly compared the differences in magnetic performance of these topologies. This paper carries out a comprehensive investigation, employing both analytical and 3D finite element analyses, to compare the magnetic performance of three topologies: yokeless and segmented armature (YASA), axial flux internal rotor (AFIR), and offset AFIR. The findings reveal that each topology offers specific advantages for different applications. The YASA topology excels in minimizing core losses; the AFIR configuration achieves the highest torque density; and the offset AFIR topology shows the highest efficiency. The offset AFIR topology appears to offer advantages for a wide array of applications due to its higher power factor and lower permanent magnet loss, leading to reduced costs for converter design and cooling system design. [ABSTRACT FROM AUTHOR]

Fractional slot concentrated winding (FSCW) permanent magnet (PM) machines are gaining more attention for low‐speed applications because of their great advantages. This paper proposes a new structure for an FSCW double rotor axial flux PM synchronous machine (DRAFPMSM) with counter‐rotating rotors. In addition, an analytical formula for the Back EMF waveform of the proposed structure is presented. The accuracy of the formula is investigated by designing a 40 W sample machine. The rotors of this machine rotate with speeds of 600 and 428 rpm in opposite directions. The Back EMF of the sample machine is calculated using the suggested formula. In addition, the finite element method (FEM) is used to determine the Back EMF waveform. Comparison of the obtained results confirms that the new formula yields the Back EMF precisely such that the results well match to those of FEM. The effect of the relative position of two rotors on the Back EMF waveform is investigated using the proposed formula. In addition, the optimum relative position of two rotors for minimizing the Back EMF THD of the case study machine is determined. [ABSTRACT FROM AUTHOR]

Cogging torque can affect the performance of permanent magnet (PM) homopolar inductor machines (HIMs). In order to find the reduction methods of the PM HIM cogging torque, it is necessary to investigate its production mechanism and analytical model. In this paper, the production mechanism of the PM HIM cogging torque is revealed from the perspective of air‐gap field modulation principle. It is found that the air‐gap permeance of PM HIMs can modulate their air‐gap magneto‐motive force (MMF) and then a large number of modulated air‐gap magnetic fields are generated. These magnetic fields with identical production condition but different rotation speeds or rotation directions can interact with each other, hence the production of the PM HIM cogging torque. By the combination of energy method and air‐gap field modulation principle, the cogging torque analytical model of PM HIMs is derived. Based on the obtained analytical model, the methods for reducing the PM HIM cogging torque are further analyzed. Finally, a 48‐slot/4‐pole (48S4P) PM HIM is designed and exampled. The air‐gap flux density of the 48S4P PM HIM is simulated by three‐dimensional (3‐D) finite element analysis (FEA). Based on the harmonic analysis for the simulated results, the correctness of the proposed cogging torque production mechanism is validated. In addition, a prototype of the 48S4P PM HIM is manufactured. The cogging torque in the prototype is obtained by the analytical model, 3‐D FEA and experiments, respectively. The simulation and measurement results verify the correctness of the cogging torque analytical model. © 2023 Institute of Electrical Engineer of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

A transverse flux linear motor is a special type of linear motor with a high thrust force density, and it has broad application prospects in the field of linear direct-drive systems. In the process of oil production, the vibration of the linear motor poses a significant amount of harm to the system due to its special slender structure. This paper focuses on the electromagnetic vibration of a transverse flux permanent magnet linear submersible motor (TFPMLSM). Firstly, the no-load air gap flux density is calculated based on the field modulation principle. Secondly, the radial electromagnetic force (REF) of the TFPMLSM is calculated, and the finite element method (FEM) is used to analyze the time-space and spectral characteristics of the REF. Then, the influence of secondary eccentricity on the frequency spectrum of the REF is further concluded. Finally, the natural frequencies of each vibration mode are calculated using the modal superposition method and the influence of the REF on the motor vibration is obtained through magnetic-structural coupling analysis. The research results found that the motor does not cause resonance at low speeds, and the fundamental frequency of REF has the greatest impact on electromagnetic vibration. [ABSTRACT FROM AUTHOR]

With the development of eddy current brake (ECB), they are widely used in life and military. Through the ECB, the resistance is converted into thermal energy and dissipated in the air. Thermal energy will make the temperature rise and the heat cannot be dissipated quickly. The electromagnetic characteristics of many parts in the ECB are very sensitive to temperature. Therefore, the study of temperature field is very important for it. This paper takes the linear cylindrical ECB as an example to study the heat generated under the intense impact and high speed condition. The temperature field is calculated through finite element method (FEM) ways. According to the temperature distribution characteristics, the cooling measures of permanent magnet brake are studied to effectively reduce the temperature rise of the brake, ensuring its reliability. [ABSTRACT FROM AUTHOR]

The main objective of the paper is to demonstrate the functionality and reliability of a hydrokinetic turbine system -- a submersible electric generator, suitable for very low watercourses. To achieve this goal, it is necessary to design and build a prototype of a hydrokinetic turbine, coupled with an electric generator with excitation made with permanent magnets. This paper presents an analytical model and a finite element numerical model for estimating the electrical parameters of the generator (voltage, current, power, etc.). The two models were compared, and the results were extrapolated, in the analytical model, for several speed values. [ABSTRACT FROM AUTHOR]

In this paper, an improved Halbach array structure of a direct-drive linear motor for wave energy conversion is proposed, and its magnetic circuit structure is modeled and the induced electromotive force (EMF) generated by vertical wave energy conversion is deduced. Then, using the internal and external parameters of the wave energy conversion direct-drive motor, that is, four internal parameters of the magnetic circuit topology and two external parameters of the mover motion, the influence of these parameters on the induced EMF of the direct-drive motor in the wave energy conversion is analyzed. Since the theoretical analysis results of the model are consistent with the results of the two kinds of permanent magnet materials analyzed by the finite element method (FEM), the model and analysis method of the direct drive motor are correct. The investigation show that the modeling method proposed in this paper can be used to optimize the energy conversion of the direct-drive motor from two aspects: the internal parameters of the magnetic circuit topology of the direct-drive motor and the external parameters of the mover motion. [ABSTRACT FROM AUTHOR]

This paper proposes a new design method for sleeve thickness and interference based on a multi-dimensional visualization algorithm that overcomes difficulties in solving. The contact pressure between the rotor core and the permanent magnet, the maximum equivalent Mises stress of the permanent magnet, and the maximum equivalent Mises stress of the sleeve are selected as the optimization objectives. The stress limit strength of the permanent magnet and sleeve are taken as constraints, and the sleeve thickness and interference are selected as decision variables. Then the multi-dimensional visualization algorithm is used to find the optimal region of sleeve thickness and interference. Finally, the design solution is validated by the finite element method. The results show that the design method proposed in this paper can obtain the optimal region of sleeve thickness and interference with the characteristics of a simple solution process and intuitive results. [ABSTRACT FROM AUTHOR]

Factors such as insufficient heat dissipation and excessively high temperature can easily lead to demagnetization of the PMs in permanent-magnet (PM) motors. As a result, the magnetic field distribution of the motor will not be uniform, producing fault harmonics and lowering the operational performance of the motor. An essential stage in the diagnosis of faults and the monitoring of motor condition is the establishment of an accurate model of motors with demagnetization faults. In this paper, demagnetization faults are modeled by changing the Fourier coefficients in the Fourier expansion of the magnetization of PMs. This model can be used to determine the motor performance under various types of demagnetization, including radial air gap flux density, back electromotive force (EMF), and torque. On this basis, the corresponding relationship between the demagnetization degree and the fault signature is established, to provide a theoretical foundation for the subsequent demagnetization fault diagnosis. The finite element analysis (FEA) verifies the effectiveness and superiority of the proposed analytical model. The modeling method proposed in this paper can be applied to PM motors with PMs having different magnetization directions and shapes because it is based on the demagnetization region of PMs. [ABSTRACT FROM AUTHOR]

The reluctance machine is a potential candidate for electrical vehicle propulsion because of its reliable structure, low cost, flexible flux regulation ability, and wide speed range. However, the torque density is unsatisfactory because of the poor excitation ability and low stator core utilization factor. To solve this problem, in this paper, a novel hybrid reluctance machine (HRM) with the skewed permanent magnet (PM) and the zero-sequence current is proposed for electric vehicles. The skewed PM has two magnetomotive force (MMF) components with different functions. The radial MMF component provides extra torque by the flux modulation effect. The tangential MMF component can generate a constant biased field in the stator core to relieve the saturation caused by the zero-sequence current and thus improve the utilization factor of the stator core. Therefore, torque improvement and the relief of stator core saturation can be simultaneously achieved by the skewed PM. In this paper, the machine structure and principle of the proposed machine are introduced. And ultimately, the machine's electromagnetic performances are evaluated under different PM magnetization directions and zero-sequence current angles by using finite element analysis (FEA). [ABSTRACT FROM AUTHOR]

In this paper, a novel variable‐leakage‐flux interior permanent magnet (VLF‐IPM) motor is proposed, which is a kind of mechanical flux‐adjusting PM motor. The VLF‐IPM motor can obtain the advantages of the IPM motor and overcome the difficulty to adjust PM airgap flux by locating a self‐activating device that is introduced in this paper on the rotor. The effect of the flux barriers on the flux leakage circuit is analysed by establishing a rotor parametric model to clarify the influence of flux barriers of the VLF‐IPM motor on flux‐adjusting performance. Then, the electromagnetic performance of VLF‐IPM motors with different volume ratios of cylindrical permanent magnets (CPMs) and rectangular permanent magnets (RPMs) are compared by using the finite element analysis (FEA) method, and the experiment results show that VLF‐IPM motor with characteristics of 0 < κrc < 1 has more advantages comprehensively. Moreover, a multi‐objective optimization process is adopted based on sensitivity analysis which can reflect the influences of geometric parameters on the optimization objectives including average torque, torque ripple and cogging torque. Then, the Non‐dominated Sorting Genetic Algorithm II(NSGA‐II) is utilised to determine the optimal model. Finally, a prototype is manufactured and tested, and the effectiveness of the novel VLF‐IPM motor and the self‐activating device are verified by the simulation and experiments. [ABSTRACT FROM AUTHOR]

An analytical subdomain model is employed in this paper for predicting the magnetic field distributions in a three-phase double-stator permanent magnet synchronous machine (DSPMSM) during open-circuit and onload conditions. Due to the stator cores are located in the outer and inner parts of the motor, the DS-PMSM construction is quite complex. The rotor magnets are positioned between these two stators. The stator inner radius, stator outer radius, slot opening, magnet arc, magnet thickness, inner and outer air-gap thickness and number of windings turns will directly influence the motor performance in DS-PMSM. The analytical subdomain model employed in this paper has a significant advantage as a rapid design tool since it is capable of precisely predicting the performance of DS-PMSM while requiring less computational effort. The analytical model was initially created using the separation of variables technique in four subdomains based on the Poisson’s and Laplace’s equations: inner air-gap, inner magnet, outer magnet and outer air-gap. Applying the appropriate boundary and interface conditions yields the field solutions in each subdomain. Besides, the fractional DSPMSM with different number of slots between outer and inner stators to rotor poles can result in low cogging torque and non-overlapping winding configuration. The analytical results are validated by Finite Element Analysis (FEA). The slotted air-gap flux density, back-emf, and output torque have all been evaluated as electromagnetic performances. The results demonstrate that the suggested analytical model is capable of accurately predicting the DSPMSM performance. [ABSTRACT FROM AUTHOR]

Direct-torque-control-driven permanent magnet synchronous machines eliminate the need for a position sensor while providing improved torque dynamics. However, the structure, regulation principle and nature of compensation of hysteresis-based controllers used in direct torque control impacts performance under faulty operating conditions. This paper analyzes the reaction of direct torque control to the presence of various faults that occur in permanent magnet synchronous machines. The analysis presented reveals that the direct torque control injects a negative sequence voltage and manipulates the torque angle to meet the control objectives when a fault occurs. The co-simulation of finite element analysis and a multi-physic circuit simulator is used to validate the response of the hysteresis-based controller to the machine health. The results indicate that the hysteresis comparators have the ability to mask the impact of the faults in the direct-torque-control-driven permanent magnet synchronous machines. [ABSTRACT FROM AUTHOR]

Magnetotactic bacteria have great potential for use in biomedical and environmental applications due to the ability to direct their navigation with a magnetic field. Applying and accurately controlling a magnetic field within a microscopic region during bacterial magnetotaxis studies at the single-cell level is challenging due to bulky microscope components and the inherent curvilinear field lines produced by commonly used bar magnets. In this paper, a system that integrates microfluidics and electromagnetic coils is presented for generating a linear magnetic field within a microenvironment compatible with microfluidics, enabling magnetotaxis analysis of groups or single microorganisms on-chip. The platform, designed and optimised via finite element analysis, is integrated into an inverted fluorescent microscope, enabling visualisation of bacteria at the single-cell level in microfluidic devices. The electromagnetic coils produce a linear magnetic field throughout a central volume where the microfluidic device containing the magnetotactic bacteria is located. The magnetic field, at this central position, can be accurately controlled from 1 to 10 mT, which is suitable for directing the navigation of magnetotactic bacteria. Potential heating of the microfluidic device from the operating coils was evaluated up to 2.5 A, corresponding to a magnetic field of 7.8 mT, for 10 min. The maximum measured heating was 8.4 °C, which enables analysis without altering the magnetotaxis behaviour or the average swimming speed of the bacteria. Altogether, this work provides a design, characterisation and experimental test of an integrated platform that enables the study of individual bacteria confined in microfluidics, under linear and predictable magnetic fields that can be easily and accurately applied and controlled. [ABSTRACT FROM AUTHOR]