Search

This paper reports experimental and numerical studies on the compression resistances of aluminium alloy equal-leg angle section stub columns after exposure to fire. An experimental programme was first conducted, including heating tests, eight post-fire material coupon tests and sixteen post-fire stub column tests. Following the experimental programme, a numerical modelling programme was conducted, where finite-element models were developed and validated. The validated models were then used to perform parametric studies to derive additional numerical data. Based on the obtained test and numerical data, the relevant design rules used in Europe, China, America, Australia and New Zealand as well as the continuous strength method were assessed. The assessment results generally show that the current international standards lead to significant conservative and scattered design resistances when used for the post-fire design of aluminium alloy equal-leg angle sections under compression, particularly for those after exposure to elevated temperatures of 300 °C to 550 °C, due to the neglect of significant post-fire material strain hardening. The continuous strength method is found to provide greatly improved design accuracy and consistency over the European, Chinese, American and Australian/New Zealand standards for the post-fire design of aluminium alloy equal-leg angle sections, since it accounts for the post-fire material hardening. • Post-fire compression resistances of aluminum alloy equal-leg angle sections were studied. • Sixteen post-fire stub column tests were conducted. • FE models were developed and validated against the test results, and then used to perform parametric studies. • The European, American, Australian/New Zealand and Chinese codes and the continuous strength method were evaluated. [ABSTRACT FROM AUTHOR]

This paper presents experimental and numerical investigations into the web crippling behaviour and load-carrying capacity of stainless steel built-up I-section members under End-Two-Flange (ETF) concentrated transverse loading. An experimental programme was conducted on 23 austenitic and duplex stainless steel built-up I-section specimens, with each consisting of two identical press-braked channel sections assembled back-to-back by means of self-tapping screws. Following the experimental programme, a numerical modelling programme was performed, where finite element models were firstly developed to replicate the tests and then used to conduct parametric studies. Based on the test and numerical data, the existing design rules for stainless steel built-up I-section members failing by web crippling, as set out in the current European, American and Australian/New Zealand design standards, were assessed. The comparisons indicated that the European and Australian/New Zealand design standards resulted in overly conservative and rather scattered failure load predictions, while the American design standard led to less scattered failure load predictions, but with many predictions on the unsafe side. Therefore, an improved design approach was proposed and shown to provide substantially improved failure load predictions for stainless steel built-up I-section members under End-Two-Flange loading. • The web crippling behaviour of stainless steel built-up I-sections under ETF loading was studied. • Tests were conducted on 23 stainless steel built-up I-section specimens. • FE models were developed and validated against test results and then used for parametric studies. • The existing codified design rules were assessed and a new design approach was proposed. [ABSTRACT FROM AUTHOR]

This paper presents experimental and numerical investigations into the post-fire cross-section compressive behaviour and resistances of circular recycled aggregate concrete-filled stainless steel tube (RACFSST) stub columns. Twelve stub column specimens, fabricated from concretes with three recycled coarse aggregate replacement ratios (0%, 35% and 70%), were tested after exposure to the ISO-834 standard fire for 0 min (i.e. at ambient temperature), 15 min, 30 min and 45 min. The experimental investigation included heating and cooling of specimens, cylinder tests and post-fire tensile coupon tests and stub column tests. The test results, including load–end shortening curves, failure loads and failure modes, were fully reported and the initial compressive stiffnesses and confinement effect were discussed. The numerical investigation was subsequently conducted, where thermal and mechanical finite element models were developed and validated against the test results and then used to perform parametric studies to generate further numerical data. Given the absence of design codes for stainless steel–recycled aggregate concrete composite structures after exposure to fire, the relevant design rules for circular natural aggregate concrete-filled carbon steel tube stub columns at ambient temperature, as set out in the European code, Australia/New Zealand standard and American specification, were assessed, using post-fire material properties, for their applicability to circular RACFSST stub columns after exposure to fire, based on the test and numerical data. The assessment results generally revealed that the European code and the Australian/New Zealand standard led to an acceptable level of design accuracy and consistency, while the American specification resulted in rather conservative and scattered post-fire cross-section compression resistance predictions. • The compressive behaviour of circular RACFSST stub columns after exposure to fire is investigated. • Post-fire compression tests on twelve circular RACFSST stub column specimens are conducted. • The influences of heating durations and RCA replacement ratios are analysed. • Thermal and mechanical FE models are validated against test results and then used to conduct parametric studies. • The relevant design codes are assessed against the test and FE data. [ABSTRACT FROM AUTHOR]

This paper reports experimental and numerical investigations into the structural behaviour and resistances of high strength concrete-filled stainless steel tube (HCFSST) beam-columns under combined compression and bending. An experimental investigation was conducted on sixteen HCFSST beam-columns specimens fabricated from stainless steel tubes with two cross-section sizes and high strength concretes with four material grades, and included concrete cylinder tests, tensile coupon tests, initial global geometric imperfection measurements and eccentric compression tests. The test setups and procedures were fully reported and the experimental observations were discussed and analysed in detail. It was found that the plane cross-section assumption was valid for eccentrically loaded HCFSST sections and the lateral deflection distribution patterns for HCFSST beam-columns were approximately half-sine wave shapes. The test results were used in a subsequent numerical investigation for the validation of finite element models, which were then employed to conduct parametric studies to generate additional numerical data over a wide range of cross-section dimensions, member lengths and loading combinations. Based on the experimental and numerical results, the relevant design rules, as set out in the European code, American specification and Australian/New Zealand standard, were evaluated for their applicability to HCFSST beam-columns. The evaluation results revealed that the European code provided accurate but scattered failure load predictions when used for HCFSST beam-columns, while the American specification and Australian/New Zealand standard resulted in conservative and scattered failure load predictions. • The behaviour of high strength concrete-filled stainless steel tube (HCFSST) beam-columns is investigated. • Eccentric compression tests on sixteen HCFSST beam-column specimens are conducted. • The ductility, strength, longitudinal strain development and lateral deflection distribution are analysed. • FE models are developed to validate against the test results and then used to conduct parametric studies. • The applicability of relevant design codes is assessed against test and FE data. [ABSTRACT FROM AUTHOR]

The flexural buckling behaviour and resistances of press-braked stainless steel Z-section columns are investigated in this paper, based on experiments and numerical modelling. An experimental investigation was conducted on two press-braked stainless steel Z-sections and included material testing, initial geometric imperfection measurements and twelve fixed-ended column tests. Minor-axis flexural buckling was observed for all press-braked stainless steel Z-section column specimens upon testing. The key obtained fixed-ended column test results, including failure loads, load–deformation histories and failure modes, were fully reported. Following the experimental investigation, a numerical investigation was performed, with finite element models developed to validate against the fixed-ended column test results and then used to conduct parametric studies to generate additional numerical data. On the basis of the test and numerical data, the relevant buckling curves, as specified in the European code, American specification and Australian/New Zealand standard, were evaluated and shown to provide accurate and consistent flexural buckling resistance predictions for press-braked stainless steel Z-section columns. • The flexural buckling behaviour of press-braked stainless steel Z-section columns was studied. • Twelve fixed-ended column tests were conducted. • FE models were developed to validate against the test results and then used to perform parametric studies. • The codified buckling curves were assessed, showing good design accuracy and consistency. [ABSTRACT FROM AUTHOR]

• The web crippling behaviour of cold-formed steel channel section having elongated edge-stiffened web holes under interior-two-flange loading condition was studied numerically. • The results of a total of 1,227 new finite element analysis were reported. • Design formulae for the web crippling strength reduction factor were suggested. • A direct strength method (DSM) equation was also presented to evaluate web crippling strength. In the past decade, cold-formed steel (CFS) channel sections having circular edge-stiffened web holes have been developed in New Zealand. Such edge-stiffened holes increase the strength of the CFS channel sections, compared to an equivalent section having unstiffened holes, while still allowing full service integration. In the case of web crippling, previous research has found that use of edge-stiffened holes almost results in the same strength of an equivalent channel-section having a plain web. Such circular edge-stiffened web holes can now be extended to elongated edge-stiffened web holes. However, for such elongated holes, no experimental tests have been reported in the literature. In this paper, a numerical investigation was carried out, and non-linear finite element (FE) analyses were used to investigate the web crippling behaviour of CFS channel sections having edge-stiffened web holes under the interior-two-flange (ITF) loading condition. The cases of both flange fastened and flange unfastened were considered. The FE models were validated against test results of sections having circular edge-stiffened web holes; good agreement in terms of the load–displacement curves and deformed shapes was shown. Using the validated FE models, a parametric study was carried out on CFS channel sections having elongated un-stiffened and edge-stiffened web holes, comprising 1,227 finite element analyses (FEA) results. Compared to sections having a plain web, for the case of an elongated opening, without any edge-stiffener, having an aspect ratio of two and three, the average reduction in web crippling strength was 39% and 49%, respectively. However, for an edge-stiffened hole, the reduction in the web crippling strength was reduced to only 2% and 16%, respectively. Finally, the design equations in the form of the web crippling reduction factor (R p) and the equations based on the direct strength method (DSM) for CFS sections with elongated web holes were proposed. [ABSTRACT FROM AUTHOR]

• Structural performance of cold-formed steel built-up section members under synchronous non-uniform bending and compression was investigated. • Thirty-five beam-column tests under unequal end moments were conducted to examine the effect of moment gradients. • Failure modes involving local, distortional and flexural buckling were found in the experiments. • Comparisons of experimental loading capacities with nominal strengths were performed to evaluate existing design rules. • Reliability analysis was performed to examine the appropriateness of current design codes. The experimental study presented in this paper aimed to examine the performance of cold-formed steel built-up section beam-columns experiencing non-uniform bending. The test program was performed on built-up open and closed sections that were manufactured from steel grades G500 and G550 zinc-coated sheets. The test specimens were assembled by connecting two identical channels with discrete connectors along the longitudinal direction. Two member lengths and two plate thicknesses were considered for the test specimens to investigate the stability of the newly designed thin-walled section beam-columns. In total, thirty-five beam-column tests were carried out under pinned supports. The test results including loading capacity, failure mode and axial load-lateral deflection response were obtained and are fully reported in this paper. Moreover, the comparison of experimental loading capacities with nominal strengths was conducted to evaluate the applicability of the interaction curves specified in the North American Specification AISI S100, the Australian/New Zealand Standard AS/NZS 4600, the European Code EN 1993–1-1 and the American Specification ANSI/AISC 360 with nominal bending and compression resistances calculated by direct strength method for the thin-walled section beam-column members under moment gradients. Overall, these design methods were conservative for strength predictions of the built-up open section beam-column members under unequal end moments. For the built-up closed section members experiencing synchronous non-uniform bending and compression, the aforementioned design methods generally offered slightly conservative strength predictions, except for the interactive formula in the European Code with bending and compression resistances determined by direct strength method. [ABSTRACT FROM AUTHOR]

• The structural behaviour of cold-formed steel T -stub connections with HRC and screws was studied experimentally and numerically. • The results of a total of 15 new experimental tests were reported. • Finite element analysis was conducted and validated against the test results. • The prediction accuracy of current design standards was evaluated. Cold-formed steel (CFS) T -Stub connections are widely used in single-story buildings, and their use is increasing in multi-story and long-span buildings. Recently, an innovative CFS T -Stub connection was developed using self-drilling screws and the Howick Rivet Connector (HRC), and such a newly-developed connection demonstrated excellent structural performance in the building industry. In this paper, a comprehensive experimental and numerical investigation was conducted to investigate the failure mechanism and structural behaviour of CFS T -Stub connections with a combination of HRC and screws under tension force, considering the effects of screw numbers. Firstly, a total of 15 new experimental tests were conducted on the CFS T -Stub connections with various numbers of screws. From the experiments, it was observed that the HRC was subjected to shear failures, while screws failed primarily due to tilting and bearing failures in all investigated specimens. Then, a non-linear elasto-plastic finite element (FE) model was developed and validated against the experimental results in terms of connection strength and failure modes. Finally, the design strengths obtained from the American Iron and Steel Institute (AISI 2016) & Australia/New Zealand standards (AS/NZS 2018) and Ahmadi et al. (2016) were compared with the test and FEA results, showing that the ultimate design strength of CFS T -Stub connections was overestimated by 16% and 14%, respectively. However, for T -Stub connections with HRC alone and with HRC and one screw, these design guidelines were unconservative by 5%. [ABSTRACT FROM AUTHOR]

• The structural behaviour of press-braked austenitic stainless steel slender channel section beam-columns was studied. • Ten beam-column tests were performed. • FE models were developed to simulate the test results and then adopted to conduct parametric studies. • The codified design interaction curves were assessed, indicating conservatism. • A new improved design interaction curve was proposed. The present paper reports experimental and numerical studies of the structural behaviour and resistances of press-braked austenitic stainless steel slender channel section beam-columns under combined compression and minor-axis bending. An experimental programme, including initial geometric imperfection measurements and ten beam-column tests, was firstly performed. The test procedures, setups and results were fully reported. The experimental programme was accompanied by a numerical modelling programme, including a validation study, where finite element models were developed and validated against the test results, and a series of parametric studies, where the validated finite element models were used to generate further numerical data. The obtained test and numerical data were adopted to assess the current design interaction curves for press-braked austenitic stainless steel slender channel section beam-columns, as provided in the European code, American specification and Australian/New Zealand standard. The assessment results revealed that all the three codified design interaction curves led to conservative and scattered resistance predictions, due to the conservative compression and bending end points and inappropriate shapes. To address these shortcomings, a new design interaction curve has been proposed and shown to yield a higher level of design accuracy and consistency for press-braked austenitic stainless steel slender channel section beam-columns than the codified design interaction curves. [ABSTRACT FROM AUTHOR]

• 1. The local–flexural interactive buckling of press-braked stainless steel slender channel section columns is studied. • 2. Ten pin-ended column tests are conducted. • 3. FE models are developed and validated against the test results and then adopted to conduct parametric studies. • 4. The codified design rules are assessed and shown to yield inaccurate interactive buckling resistance predictions. • 5. A new design method is proposed, showing improved design accuracy. The present paper reports experimental and numerical studies of the local–flexural interactive buckling behaviour and resistance of press-braked stainless steel slender channel section columns. A testing programme was firstly performed, including tensile coupon tests, initial geometric imperfection measurements and ten pin-ended column tests. The pin-ended column test setup, procedures and results were fully reported and analysed. The progression of local buckling and flexural buckling was discussed in detail. Following the testing programme, a numerical modelling programme was conducted, where finite element models were developed to replicate the test responses and then employed to perform parametric studies to generate further numerical data over a wide range of cross-section dimensions and member effective lengths. The obtained test and numerical data were employed to assess the accuracy of the relevant design rules for press-braked stainless steel slender channel section columns, as set out in the European code, American specification and Australian/New Zealand standard. The assessment results revealed that the European code leads to conservative and scattered interactive buckling resistance predictions, while the American specification and Australian/New Zealand standard result in many unsafe and scattered interactive buckling resistance predictions. A new design approach was then developed, based on the Eurocode column buckling curve and the continuous strength method, and shown to lead to accurate, consistent and safe interactive buckling resistance predictions for press-braked stainless steel slender channel section columns. The reliability of the new design approach was confirmed by means of statical analyses. Besides, the relevant design rules for press-braked carbon steel slender channel section columns, as given in the North American specification, were assessed, and shown to result in unsafe though consistent interactive buckling resistance predictions, when used for their stainless steel counterparts. [ABSTRACT FROM AUTHOR]

• The structural behavior and capacity of RACFSST stub columns under combined loading are studied. • Twelve eccentric compression tests on RACFSST stub columns are conducted. • The evolution of neutral axis in RACFSST composite section as well as the confinement effect are discussed. • FE models are developed to validate against the test results and then used to conduct parametric studies. • The relevant design codes are assessed against the test and FE data. This paper reports experimental and numerical investigations into the behaviour and resistance of recycled aggregate concrete-filled stainless steel tube stub columns under combined compression and bending. Eccentric compression tests were conducted on twelve stub column specimens fabricated from austenitic stainless steel tubes with two cross-section sizes and concretes with three recycled coarse aggregate replacement ratios (0%, 35% and 70%). The test results, including the failure loads, load–mid-height lateral deflection curves, evolution of neutral axis and confinement effect, were discussed in detail. The testing programme was followed by a numerical modelling programme, where finite element models were developed and validated against the test results and then used to perform parametric studies to generate further numerical data over a wide range of cross-section dimensions and loading combinations. Given that there are no existing design codes for recycled aggregate concrete–stainless steel composite structures, the relevant codified design rules for natural aggregate concrete filled-carbon steel tube stub columns under combined compression and bending, as set out in the European code, American specification and Australian/New Zealand standard, were evaluated for their applicability to recycled aggregate concrete filled-stainless steel tube stub columns, based on the test and numerical data. The evaluation results revealed that the European code and Australian/New Zealand standard generally provide an acceptable level of design accuracy, while the American specification yields unduly conservative failure load predictions. [ABSTRACT FROM AUTHOR]

• The local–flexural interactive buckling of S690 high strength steel slender channel section columns was studied. • Twelve pin-ended compression tests were conducted. • FE models were developed and validated and then adopted to perform parametric studies. • The accuracy of the codified design rules was assessed, revealing inaccuracy. • A new design approach was proposed, showing a high level of accuracy. This paper reports an experimental and numerical investigation into the local–flexural interactive buckling behaviour and resistance of press-braked S690 high strength steel slender channel section columns. An experimental programme was firstly conducted and included initial geometric imperfection measurements and twelve pin-ended column tests. Interaction between local buckling and flexural buckling was observed for all specimens upon testing and discussed in detail. The experimental programme was accompanied by a numerical modelling programme, where finite element models were developed and validated against the test results and then employed to perform parametric studies to generate further numerical data over a wide range of cross-section dimensions and member effective lengths. The obtained test and numerical data were used to assess the accuracy of the codified design rules for press-braked S690 high strength steel slender channel section columns failing by local–flexural interactive buckling, as set out in the European code, North American specification and Australian/New Zealand standard. The assessment results revealed that the European code leads to excessively conservative and scattered resistance predictions, while the North American specification and Australian/New Zealand standard result in a higher level of design accuracy and consistency, but still with many conservative resistance predictions for columns with short to intermediate lengths. Finally, a new design approach was proposed and shown to yield substantially more accurate and consistent resistance predictions for press-braked S690 high strength steel slender channel section columns over the design codes. [ABSTRACT FROM AUTHOR]

• A total of 41 cold-formed steel built-up I-sections were tested under ETF, ITF, EOF and IOF loading conditions. • Finite element models were developed to replicate the experiments. • Parametric study of 258 specimens was performed. • The existing codified web crippling design provisions were assessed. • Design rules were proposed based on the unified equation and direct strength method. This paper reports the experiments, numerical modelling and design of cold-formed steel built-up I-sections subjected to localised loadings. The built-up I-sections were made up of two equal-sized plain channels fastened back-to-back in the web. The web crippling tests were undertaken on 41 built-up I-section members under Interior-Two-Flange (ITF), End-Two-Flange (ETF), Interior-One-Flange (IOF) and End-One-Flange (EOF) loading conditions. The effects of the arrangement of screws along the web height were investigated. After the experiments, finite element (FE) analyses considering the initial local imperfections of the web of the specimens were performed and the validity of the FE models was assessed using the test results. A parametric investigation including 258 numerical simulations was conducted to expand the database and evaluate the influences of the screw arrangements in the web height. The test and numerical results indicated that the failure modes of the specimens with different screw arrangements were generally similar in each loading condition, and the screws located close to the flange-web junctions of the sections could generally provide maximum web crippling resistances of the built-up I-sections. The design recommendations on the arrangements of screws along the web height were proposed. The experimentally and numerically generated web crippling resistances were utilized to assess the current North American specification (AISI S100), Australian and New Zealand standard (AS/NZS 4600) and European code (EN1993-1-3). The results show that the existing codified design formulas lead to either conservative or highly unsafe results. Therefore, two sets of design formulas were derived on the basis of unified equation and direct strength method. [ABSTRACT FROM AUTHOR]