Search

We employed a microwave-assisted two-pot in-situ deposition technique to incorporate zinc oxide particulates in the structure of filter paper to produce antimicrobial paper. The process involved successive immersion of filter paper samples in ZnSO4 (precursor solution) and NaOH (precipitating agent) to form Zn(OH)2, which transformed into ZnO during microwave treatment. Successful deposition of ZnO particles on the filter paper was confirmed via X-ray diffraction and the corresponding morphologies were observed using field emission scanning electron microscopy. The ZnO-deposited papers were tested for antimicrobial activity and were found to be more effective against Staphylococcus aureus (gram-positive) than Escherichia coli (gram-negative). Bacterial populations were reduced by up to 92 ± 2% and 57 ± 4% for S. aureus and E. coli, respectively. Also, it was found that the samples prepared using higher concentrations of ZnSO4 and NaOH exhibited better antimicrobial properties.

The rapid economic growth and environmental concerns have led to high demands on paper and paper-based products in terms of variety, quantity, quality, and specialty. Enhancement and functionalization with additives are constantly required. Moving away from traditional petroleum-based additives, researchers have attempted to use “green” nanoadditives by introducing renewable environmentally friendly nanocellulose. This article studies the functions of nanocellulose as bio-additives (enhancer, retention and filtration reagent, and coating aid) in paper and paper products, and overviews the research development of nanocellulose-based additives and their applications in the paper industry for both efficient production and paper functionalization. The review shows that (1) a variety of nanocellulose-based bioadditives have been reported for various applications in paper and paper-based products, while commercially viable developments are to be advanced; (2) nanocellulose was mostly formulated with other polymer and particles as additives to achieve their synergistic effects; (3) major interests have concentrated on the nanocellulose in the specialty papers as representing more value added products and in the efficient utilization of recycled fibers, which remains most attractive and promising for future development. This report shall provide most useful database information for researchers and industries for paper recycling and enhancement, and paper-based products innovation and application.

The appearance and quick spread of the new severe acute respiratory syndrome coronavirus disease, COVID-19, brought major societal challenges. Importantly, suitable medical diagnosis procedures and smooth clinical management of the disease are an emergent need, which must be anchored on novel diagnostic methods and devices. Novel molecular diagnostic tools relying on nucleic acid amplification testing have emerged globally and are the current gold standard in COVID-19 diagnosis. However, the need for widespread testing methodologies for fast, effective testing in multiple epidemiological scenarios remains a crucial step in the fight against the COVID-19 pandemic. Biosensors have previously shown the potential for cost-effective and accessible diagnostics, finding applications in settings where conventional, laboratorial techniques may not be readily employed. Paper- and cellulose-based biosensors can be particularly relevant in pandemic times, for the renewability, possibility of mass production with sustainable methodologies, and safe environmental disposal. In this review, paper-based devices and platforms targeting SARS-CoV-2 are showcased and discussed, as a means to achieve quick and low-cost PoC diagnosis, including detection methodologies for viral genomic material, viral antigen detection, and serological antibody testing. Devices targeting inflammatory markers relevant for COVID-19 are also discussed, as fast, reliable bedside diagnostic tools for patient treatment and follow-up., The authors acknowledge funding through projects Eco2Covid (POCI-01-02B7-FEDER-068174) and TecniCov (POCI-01-02B7-FEDER-069745), co-funded by FEDER through COMPETE2020 and Lisboa2020. T.P., A.R.C. and A.C.M. acknowledge funding to National Foundation for Science and Technology, I.P., FCT, through their PhD grants, references DFA/BD/8606/2020, SFRH/BD/130107/2017 and SFRH/BD/115173/2016, respectively, info:eu-repo/semantics/publishedVersion

Cellulose paper, a material that is naturally derived, low cost, lightweight, eco-friendly, and mechanically deformable, plays important roles in producing next-generation flexible electronics. Following the booms in the development of functional electronics, the soft actuators built from cellulose paper have attracted great attention. In this focused review, the milestones and recent achievements of cellulose paper-based actuators are summarized. Electro-, thermal, moisture and magnetic actuation mechanisms are utilized to acquire energy from external stimuli. Corresponding functional materials and available fabrication techniques like film assembly and layer deposition are described. Programmable actions for the emerging applications in bionics, paper grippers and robots are realized by pursuing different strategies to control the responding deformation. Along with a conclusion, the existing challenges and possible solutions in evaluating and improving the performance of cellulose paper are summarized in the final section.

Hydrothermal liquefaction derived hydrochar produced from industrial paper sludge was used as an adsorbent to remove phenol derivatives from an industrial wastewater stream. Removal efficiency for phenol was determined using synthetic solutions (10–150 ppm) using batch adsorption experiments at a constant solution pH (8), temperature (25 ± 2 °C) and rotary speed (150 rpm). The adsorption of phenol onto hydrochar followed a Freundlich isotherm and could be described with pseudo-second-order kinetic models. Analysis of the adsorption mechanisms showed that particle film mass transport was the rate-determining step in the adsorption process. A COD removal efficiency of 31 ± 1% was achieved for the industrial wastewater stream. All phenol components in the wastewater stream could be removed, but not all organic acids and cyclic ketones. The performance of the paper sludge-based hydrochar compared well with that of activated carbon (44% COD removal). The final phenol concentration in the wastewater stream was below the acceptable phenol concentration for industrial effluents (1 mg/L). The results show that paper sludge can be converted to a valuable marketable commodity that could reduce waste management costs for a paper mill, while also reducing the cost of expensive adsorbents. Highlights Industrial paper sludge waste was successfully converted to effective bio-adsorbent.; HTL-based biochar was used as adsorbent without any pretreatment.; 77.83% COD removal from industrial wastewater could be obtained.; Final total phenol concentration was below 1 ppm.; Bulk fluid mass transfer was the rate determining step in the adsorption process.

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

Cellulose based nanomaterials have the great potential to be applied to paper as bulk additive or coating material to improve overall final properties, especially in secondary fiber. In the present work, the effect of applying different kinds of cellulose nanofibrils (CNF) to papers obtained from recycled fibers using size press on physical, mechanical and barrier properties was investigated and compared with the sole use of starch as coating material. The coating process of CNF was carried out by the addition of size press grade starch to coating suspension. As a cellulose source, wheat straw was evaluated and CNF was obtained through oxidative and enzymatic pretreatments. Results indicate that starch/CNF suspension improves the overall paper properties. As a result of the deposition of coating suspension contains of 4 % wt. periodate-oxidized CNF onto paper surface, tensile and burst indices of papersheets increased as 52.2 % and 194.4 %. Significant decreases were observed in air permeability as 69.8 %. Compression tests also have been conducted to evaluate papersheets end-use properties. In comparison to the other pretreated CNF, due to is lower viscosity, applying periodate-oxidized CNF as size press significantly increased the mechanical properties of the papers fabricated from the recycled pulps. TUBITAK-TEYDEBTurkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [1505]; Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate [1505, 5180044] This work was supported by TUBITAK-TEYDEB 1505 (The Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate 1505), Project No. 5180044. WOS:000703585400013 2-s2.0-85108063350

Funding Information: The financial support of the Austrian Federal Ministry of Digital and Economic Affairs and the National Foundation for Research, Technology and Development , Austria, is gratefully acknowledged. We also thank the industrial partners Mondi, Canon Production Printing, Kelheim Fibres, and SIG Combibloc for their support. Publisher Copyright: © 2021 Copyright: Copyright 2021 Elsevier B.V., All rights reserved. Hydrophobization of cellulosic materials and particularly paper products is a commonly used procedure to render papers more resistant to water and moisture. Here, we explore the hydrophobization of unsized paper sheets via the gas phase. We employed three different compounds, namely palmitoyl chloride (PCl), trifluoroacetic anhydride/acetic anhydride (TFAA/Ac2O)) and hexamethyldisilazane (HMDS) which were vaporized and allowed to react with the paper sheets via the gas phase. All routes yielded hydrophobic papers with static water contact angles far above 90° and indicated the formation of covalent bonds. The PCl and TFAA approach negatively impacted the mechanical and optical properties of the paper leading to a decrease in tensile strength and yellowing of the sheets. The HMDS modified papers did not exhibit any differences regarding relevant paper technological parameters (mechanical properties, optical properties, porosity) compared to the non-modified sheets. XPS studies revealed that the HMDS modified samples have a rather low silicon content, pointing at the formation of submonolayers of trimethylsilyl groups on the fiber surfaces in the paper network. This was further investigated by penetration dynamic analysis using ultrasonication, which revealed that the whole fiber network has been homogeneously modified with the silyl groups and not only the very outer surface as for the PCl and the TFAA modified papers. This procedure yields a possibility to study the influence of hydrophobicity on paper sheets and their network properties without changing structural and mechanical paper parameters.

Graphical abstract Enzyme-linked immunosorbent assay (ELISA) is widely used for the detection of disease biomarkers. However, it utilizes time-consuming procedures and expensive instruments, making it infeasible for point-of-care (POC) analysis especially in resource-limited settings. In this work, a multicolorimetric ELISA biosensor integrated on a paper/polymer hybrid microfluidic device was developed for rapid visual detection of disease biomarkers at point of care, without using costly equipment. This multicolormetric ELISA platform was built on multiple distinct color variants resulted from the catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) and the etching of gold nanorods (AuNRs). The vivid color changes could be easily distinguished by the naked eye, and their red mean values allowed quantitative biomarker detection, without using any sophisticated instruments. When this multicolorimetric ELISA was integrated on a paper/polymer hybrid analytical device, it not only provided integrated processing and high portability but also enabled fast assays in about 50 min due to the unique advantages of paper/polymer hybrid devices. The limit of detection of 9.1 ng/μL of the hepatitis C virus core antigen, a biomarker for hepatitis C, was achieved using this multicolorimetric ELISA platform. This multicolor ELISA analytical device provides a new versatile, user-friendly, affordable, and portable immunosensing platform with high potential for on-site detections of various viruses, proteins, and biomarkers for low-resource settings such as at home, public venues, rural areas, and developing nations. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03359-8.

Graphical abstract During epidemics, such as the frequent and devastating Ebola virus outbreaks that have historically plagued regions of Africa, serological surveillance efforts are critical for viral containment and the development of effective antiviral therapeutics. Antibody serology can also be used retrospectively for population-level surveillance to provide a more complete estimate of total infections. Ebola surveillance efforts rely on enzyme-linked immunosorbent assays (ELISAs), which restrict testing to laboratories and are not adaptable for use in resource-limited settings. In this manuscript, we describe a paper-based immunoassay capable of detecting anti-Ebola IgG using Ebola virus envelope glycoprotein ectodomain (GP) as the affinity reagent. We evaluated seven monoclonal antibodies (mAbs) against GP—KZ52, 13C6, 4G7, 2G4, c6D8, 13F6, and 4F3—to elucidate the impact of binding affinity and binding epitope on assay performance and, ultimately, result interpretation. We used biolayer interferometry to characterize the binding of each antibody to GP before assessing their performance in our paper-based device. Binding affinity (KD) and on rate (kon) were major factors influencing the sensitivity of the paper-based immunoassay. mAbs with the best KD (3–25 nM) exhibited the lowest limits of detection (ca. μg mL−1), while mAbs with KD > 25 nM were undetectable in our device. Additionally, and most surprisingly, we determined that observed signals in paper devices were directly proportional to kon. These results highlight the importance of ensuring that the quality of recognition reagents is sufficient to support desired assay performance and suggest that the strength of an individual’s immune response can impact the interpretation of assay results. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03317-4.

BackgroundThe analysis of the quality of food is important to protect humans from food-borne or food-based illnesses caused by pathogens, such as bacteria, fungi, viruses, and protozoa. Rapid identification of these pathogens is critical to ensure food safety. Various detection and identification strategies exist; however, they are laborious and time consuming and hence the detection takes longer time. The aim of this study was to develop the specific and fast method for the detection of contaminants in milk.ResultsIn this study, we have developed a simple paper-based PCR method with minimum sample preparation process. The 16S rDNA universal primers were used for the detection of bacterial contaminants. LacZ primers were used for coliform detection which causes serious illness and hence their detection is crucial. ITS region primers were used for fungal detection. The most unique thing about this study is use of Whatman paper no. 1 as sample carrier material. We developed and validated the paper-based PCR method and used it for the detection of microbes and coliforms using milk as a representative sample.ConclusionWe evaluated this method for its suitability in the detection of contaminant microbes using different milk samples. The paper-based method could successfully detect contaminants in the milk samples and the results were comparable to the traditional microbial detection method. The traditional microbiological method takes at least 18–20 h for detecting the presence of microbes in any sample but the developed paper-based PCR method can confirm the microbial presence in 2–3 h. This is very promising especially in the testing where sample sterility is crucial.

Environmentally friendly and energy saving treatment of black liquor (BL), a massively produced waste in Kraft papermaking process, still remains a big challenge. Here, by adopting a Ni CaO Ca12Al14O33 bifunctional catalyst derived from hydrotalcite-like materials, we demonstrate the feasibility of producing high-purity H2 (∼96%) with 0.9 mol H2 mol−1 C yield via the sorption enhanced steam reforming (SESR) of BL. The SESRBL performance in terms of H2 production maintained stable for 5 cycles, but declined from the 6th cycle. XRD, Raman spectroscopy, elemental analysis and energy dispersive techniques were employed to rationalize the deactivation of the catalyst. It was revealed that gradual sintering and agglomeration of Ni and CaO and associated coking played important roles in catalyst deactivation and performance degradation of SESRBL, while deposition of Na and K from the BL might also be responsible for the declined performance. On the other hand, it was demonstrated that the SESRBL process could effectively reduce the emission of sulfur species by storing it as CaSO3. Our results highlight a promising alternative for BL treatment and H2 production, thereby being beneficial for pollution control and environment governance in the context of mitigation of climate change.

The present study reports the characterization of reverse osmosis (RO) technology at water treatment plant Cogen-2 in paper and Board mills, Pakistan. RO is a commonly used process to obtain de-mineralized water for high-pressure boiler operation in thermal power plants. Scaling and fouling in three-stage RO plants is a major challenge in chemical industry due to the use of raw brackish water in the power plant of paper and board mills. In our study, the feed water quality of RO was changed from soft water to raw water to make it economical. The cleaning frequency was increased three times than normal, which was unsafe for operation and it was required to control scaling and fouling to achieve the desired result. Differential pressures behavior of all stages for 2-month data was observed without acid treatment, and the results of Langelier Saturation Index (LSI) control parameters (temperature, pH, total dissolved solids, calcium hardness, and alkalinity) clearly showed the abnormality. To optimize scaling and fouling of RO, the LSI factor was controlled in total reject water for the next 2 months by acid treatment in feed water. Duration of chemical cleaning and membranes’ life has been extended by fouling and scaling control. Understanding the effect of operational parameters in RO membranes is essential in water process engineering due to its broad applications in drinking water, sanitation, seawater, desalination process, wastewater treatment, and boiler feed water operation. The product flow increased from 18.3 to 19.9 m3/h, and this was due to a decrease in the rejection flow from 8.2 to 6.7 m3/h. The total reject stream pressure also increased from 8.1 to 9 bar. A lower value of LSI of 1.6 is obtained in the reject water stream after the acid treatment.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Currently, most of the collected waste medium-density fiberboards (MDF) is incinerated or landfilled, as economically viable recycling methods are yet to be developed. By steam refining waste medium-density fiberboards (MDF), it is possible to hydrolyze the incorporated resins and isolate a high yield fiber fraction. Further refining of the steam treated fibers might enable the fibers to be utilized in applications such as paper packaging, facilitating a cascading use of the waste material stream. To this end, intimate knowledge of the material is needed. In this study, the steam refined fibers of two waste MDF samples containing differing amounts of softwood and hardwood underwent refining and beating. The resulting fibers were characterized regarding their morphology and paper test sheets were produced to evaluate their strength (compression-, tensile- and tear-strength). Distinct differences in response to refining between the MDF samples were apparent. For the sample with the higher hardwood share an increase in strength properties with increasing steam treatment severities could be observed and it was possible to produce test sheets with comparable compression strength to recycled pulp for industrial corrugated paperboard. For the sample with a higher share of softwood, the steam treatment severity did not show any influence on fiber morphology or paper properties, and the resulting paper strength was low in comparison to the other steam refined waste MDF sample. Graphic Abstract

The development of industry and of the Internet of Things (IoTs) have brought energy issues and huge challenges to the environment. The emergence of triboelectric nanogenerators (TENGs) has attracted wide attention due to their advantages, such as self-powering, lightweight, and facile fabrication. Similarly to paper and other fiber-based materials, which are biocompatible, biodegradable, environmentally friendly, and are everywhere in daily life, paper-based TENGs (P-TENGs) have shown great potential for various energy harvesting and interactive applications. Here, a detailed summary of P-TENGs with two-dimensional patterns and three-dimensional structures is reported. P-TENGs have the potential to be used in many practical applications, including self-powered sensing devices, human–machine interaction, electrochemistry, and highly efficient energy harvesting devices. This leads to a simple yet effective way for the next generation of energy devices and paper electronics.

Paper and pulp mills generate substantial quantities of cellulose-rich sludge materials that are disposed in landfills at a large scale. For sustainability purposes, sludge materials can be bioprocessed to produce renewable fuels and useful chemicals. The enzymatic hydrolysis of cellulose is the process bottleneck that affects the conversion economics directly by using zero-cost raw materials. In order to study and optimize the process, the characteristics of the sludge raw materials should be first evaluated. In this work, sludge samples were obtained from paper mills located at different locations in Wisconsin and Minnesota. Part of the sludge samples was washed (de-ashed) with hydrochloric acid while the other part remained unwashed. The samples were subjected to multiple spectroscopic analyses techniques to evaluate the morphological properties of cellulose fibers and to estimate the total structural carbohydrate content. The results showed that the de-ashing process changed some fiber characteristics and cellulose crystallinity structure in all sludge samples. Sludge sample A (obtained from Kraft pulp and recycled paper mill region) showed a high percentage of fiber, with crystalline cellulose, compared to the other two sludge samples suggesting that sludge A is a valuable source to make value-added products. Aspen Plus mass and energy calculations performed in view of the ‘zero’ cost and the reliable supply of sludge raw materials producing 2 mol H2/mol glucose. Moreover, the results showed that extracting crystalline cellulose from these sludge samples is more profitable than crystalline cellulose made from the other lignocellulosic feedstocks. The results reported here showed that the utilization of these sludge materials would be an economically attractive and promising alternative for the production of hydrogen.

Achieving an efficient catalyst in the ATRP system with a simple design, preparation from available materials, and high recyclability is a significant challenging issue. To attain the goal, herein, we used chitosan (CS)-modified cellulose filter paper (FP) as a green support for the synthesis of dip catalyst. The preparation of this catalyst involved surface treatment of the FP strips by CS coating through a dipping method, which increased the affinity of the substrate for adsorbing copper ions in the next step. The Cu@CS-FP catalyst was prepared without the requirement of any ligands. The synthesized dip-catalyst, in the form of the strips, was employed for the first time in the ATRP reaction of methyl methacrylate to assay catalytic activity. Catalytic insertion/ removal (ON/OFF) experiments were carried out during the polymerization. A reasonable control over the molecular weight with high conversion (68%) and polydispersity index of 1.32 under mild reaction conditions were obtained. Significantly, because of the facile separation of the catalyst, the amount of copper that remained in the polymer was very low (2.7 ppm). Also, the recyclability of the catalyst was investigated for five runs. The conversion in the final run was 64% without a loss of catalyst efficiency.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Introduction We developed low-cost, portable paper-based diagnostic devices for detection of human immunoglobulin M (IgM) and immunoglobulin G (IgG) in serum without any sample preparation. These devices can be used to help identify presence of diseases, used to provide rapid results ( Materials and Methods We successfully accomplished colorimetric detection of human IgG and human IgM using a sandwich-style assay within the microfluidic paper device via vertical flow immunoassay configuration. The reaction zone in the wax printed paper layer is a small circular pattern. Gold nanoparticles conjugated with anti-human IgG and IgM antibodies have been used for colorimetric detection of IgG or IgM by naked eye. Colorimetric signal can be precisely quantified through implementation of image analysis software which can be developed as an app for a smartphone. The size of the device is 2 cm × 2 cm × 1 mm. Results Colorimetric detection of human IgG was accomplished at 100 fg/mL concentration using a gold nanoparticle–conjugated anti-human IgG antibody. The developed platform has a dynamic range of IgM and IgG concentrations between 0.1 pg/mL and 100 μg/mL. These devices provided a color readout in Conclusions Because of the inherent simplicity of the device operation and their ease of use, there is no variation between samples and users of the device. This low-cost approach enables multiplexing with >1 measurement performed in parallel at the same time. We anticipate that because of the sensitivity, specificity, ease of use, and overall reliability, this approach will become a standard for diagnosis of diseases and health conditions.

The present work describes a sensitive, simple, cost-effective and fast analytical procedure to detect the parabens in industrial waste effluent water samples using novel activated carbon nanofiber (CNF) modified filter paper based solid phase extraction technique coupled with liquid chromatography with photodiode array detector (UPLC-PDA). The carbon nanofiber coated filter paper was used as an adsorbent and also characterized by field emission scanning electron microscope (FESEM) showed superior porous structure. Various factors effecting the adsorption and desorption process were studied. The optimum parameters which improve the efficiency are paper length 1 cm × 2 cm, adsorption time 15 min, eluent methanol, eluent volume 5 mL, sample pH 7, desorption time 2 min, 2% salt addition and 300 rpm stirring rate respectively. The parabens exhibited superior linearity ranging from 0.1-50 ng mL-1. The regression coefficient (R2) value ranging from 0.9981-0.9989. This method exhibited good sensitivity with the quantification limit (LOQ) between 0.5-0.75 ng mL-1 and detection limit (LOD) over the range of 0.1-0.25 ng mL-1. The precision was expressed from the RSDs values from 0.74-0.97 %. The spiked analytes revealed excellent recoveries in the range of 95.30-116.72 % with RSD less than 5.72 % for all the water samples also applied for real samples.

Detecting vascular endothelial growth factor C (VEGF-C), a kind of tumor biomarker, is of significant clinical importance in evaluating the prognosis of patients with cancer. However, laboratory analyses are usually not suitable for point-of-care testing because they are expensive and time consuming. In response to these challenges, we fabricated an origami paper-based microfluidic electrochemical device. To improve the specificity of VEGF-C detection, nanocomposites, synthesized by new methylene blue (NMB), amino-functional single-walled carbon nanotubes (NH2-SWCNTs), and gold nanoparticles (AuNPs), were used to modify the surface of working electrodes. Results of electrochemical detection showed that the immunosensor had excellent linearity, ranging from 0.01 to 100 ng mL−1 (R2 = 0.988), and the limit of detection was 10 pg mL−1. To confirm the high specificity of the device under real-world conditions, we evaluated the device using clinical serum samples from our hospital. The results demonstrated that the device had an excellent performance and could provide a platform for real-time detection of cancers., Sun, Wang et al. report an origami paper-based immunosensor for the electrochemical detection of the VEGF-C biomarker in blood serum. The immunosensor is made by modifying the surface of working electrodes with new methylene blue, amino-functional single-walled carbon nanotubes, and gold nanoparticles and demonstrates excellent performance with a limit of detection in the range of picograms per milliliter.

The paper corrugation tube is an innovative kind of energy absorbing structure and shock absorber which can play an important role on the cushioning energy absorption for airdrop equipments and transportation packaging. The deformation characteristics and failure modes of the regular triangle, quadrangle, pentagon and hexagon paper corrugation tubes were comparatively studied by a series of axial static compression experiments, the cushioning energy absorption was evaluated by the seven characteristic parameters (e.g. initial peak force, mean crush force, total energy absorption, specific energy absorption, crush force efficiency, unit area energy absorption and stroke efficiency), and the influences of tube direction, cross-sectional shape, tube length and compression rate on failure modes and cushioning energy absorption were analyzed and compared. These researches showed that the tubes along X direction only have the accordion deformation mode, yet the tubes along Y direction have four deformation modes including steady state progressive buckling, Euler buckling, angular tear and transverse shear. For the paper corrugation tubes along Y direction, the cross-sectional shape has obvious influence on the cushioning energy absorption of structures, and the specific energy absorption and unit area energy absorption of regular triangle and pentagon tubes are better than those of the tubes with regular quadrilateral and hexagonal cross-section at compression rates of 12 and 48mm/min. The tube length of 150 mm or compression rate of 72 mm/min would cause the increase of contribution proportion of non-ideal deformation mode and the decrease of cushioning properties. The paper corrugation tubes along X direction have more stable and controllable deformation mode, yet the paper corrugation tubes along Y direction have better cushioning energy absorption.

We report a simple and cost-effective paper-based and colorimetric dual-mode detection of As(iii) and Pb(ii) based on glucose-functionalized gold nanoparticles under optimized conditions. The paper-based detection of As(iii) and Pb(ii) is based on the change in the signal intensity of AuNPs/Glu fabricated on a paper substrate after the deposition of the analyte using a smartphone, followed by processing with the ImageJ software. The colorimetric method is based on the change in the color and the red shift of the localized surface plasmon resonance (LSPR) absorption band of AuNPs/Glu in the region of 200-800 nm. The red shift (Δ

Coatings based on pigment and polymer binders are applied on paper surfaces to improve their surface, optical, and printing properties. Besides the coating composition, the structure and properties of the coated papers are influenced by the coating layer consolidation upon drying. In this study, the influence of drying conditions on the structure and properties of coating layers based on natural pigments (clay) and polymer binders (butadiene acrylonitrile latex) has been analyzed. Using a laboratory rod Mayer device, the coatings were applied as thin layer (about 15&ndash, 16 g/m2) on the paper surface and samples of coated paper were dried at 20 and 105 &deg, C temperatures. The optical, structural, and water absorption properties of the coating layer were evaluated by the measurement of gloss, opacity, void fraction, light scattering, and contact angle. The obtained results highlighted that both the drying temperature and latex content in the coating color have a synergic effect on the coated paper quality.

Lightweight yet strong paper with high toughness is desirable especially for impact protection. Herein we demonstrated electrically conductive and mechanically robust paper (AP/PB-GP) made of reduced graphene oxide via interfacial crosslinking with 1-aminopyrene (AP) and 1-pyrenebutyrat (PB) small molecules. The AP/PB-GP with thickness of over ten micrometer delivers a record-high toughness (∼69.67 ± 15.3 MJ m−3 in average), simultaneously with superior strength (close to 1 GPa), allowing an impressive specific penetration energy absorption (∼0.17 MJ kg−1) at high impact velocities when used for ballistic impact protection. Detailed interfacial and structural analysis reveals that the reinforcement is synergistically determined by π-π interaction and H-bonding linkage between adjacent graphene lamellae. Especially, the defective pores within the graphene platelets benefit the favorable adsorption of the pyrene-containing molecules, which imperatively maximizes the interfacial binding, facilitating deflecting crack and plastic deformation under loading. Density functional theory simulation suggests that the coupling between the polar functional groups, e.g., −COOH, at the edges of graphene platelets and −NH2 and −COOH of AP/PB are critical to the formation of hydrogen bonding network.

Neotame is an artificial sweetener with increasing consumption in recent years, excessive intake of it may bring potential health risk. In this work, a rapid method was developed to detect neotame in instant grain beverages, which was based on surface-enhanced Raman scattering (SERS) technique and filter paper-based silver nanoparticles (AgNPs@FP) substrates. The designed substrate exhibits good SERS activity with an enhancement factor of 105 because of the synergistic effect of the concentrated silver nanoparticles and filter paper. Meanwhile, the stability and repeatability of this fabricated substrate have been investigated with the relative standard deviation of 6.1%. In addition, it shows an excellent linear relationship (R 2 = 0.997) between the SERS signal and the logarithm concentration of neotame with a wide concentration range (0.05–5 g/kg) in the quantitative analysis. The limit of detection of neotame can be as low as 0.01 g/kg in instant grain beverages, which is below the maximum allowable addition level for neotame in instant grain beverages set in China (GB2760-2014, 0.16 g/kg). The proposed method has great potential for the identification and quantification of neotame in food safety applications with high sensitivity.

In China, Xuan paper has been the paper of choice as artwork support and for conservation, for several centuries. However, little is known about its material properties, especially given the many grades of sized and unsized Xuan paper. In addition, there is a lack of information on its degradation. In this research, a selection of contemporary unsized Xuan papers was investigated, representing diverse raw materials. Seven out of twelve contemporary unsized Xuan papers were determined to be approximately neutral and contain > 2% alkaline reserve, indicating good durability. Viscometry was used to determine the degree of polymerisation (DP) as none of the samples gave significant reactions to the phloroglucinol spot test. The average DP of ten contemporary unsized Xuan papers is ~ 1700, excluding two papers that have presumably been sun-bleached, and that exhibit significantly lower DP. Using X-ray fluorescence, it can be demonstrated that Ca and Si are the dominant elements and interestingly, Ca content is directly correlated with ash content and with alkaline reserve. Accelerated degradation was performed at two sets of environmental conditions, i.e. 90 °C, 30% RH and 60 °C, 70% RH, and the established degradation rates agreed with the Collections Demography model of paper degradation meaning that degradation of Xuan papers proceeds in the same way as other types of paper. This research gives fundamental insights into contemporary unsized Xuan papers, which exhibit good stability during accelerated degradation despite the low starting DP in the context of the samples used in this study. Our findings may inform methods of Xuan paper production, selection of Xuan paper for conservation purposes, as well as preventive conservation of Xuan paper-based artefacts.

Starch and derivatives thereof have proven their usefulness in paper coating processes. Among these derivatives, cationic starch has been widely used in the paper industry as a flocculation, dispersion and ink fixing agent. In another context, nanoscale cellulosic materials have been shown to improve the strength, retention of fillers, the barrier properties of packaging paper products, and printing qualities. This review summarizes the recent studies on the general components used in paper coating, describes the conventional and alternative synthetic processes of cationic starches and nanocellulose, and deals with their current and potential applications in papermaking, focusing primarily on surface treatments. Moreover, environmental applications have been considered to expand the understanding and usefulness of these materials. Further research on modified polysaccharides is encouraged to replace, in a feasible way, petro-based components of coating formulations, and to provide paper surfaces with new properties.

Process-monitoring laboratories in the pulp and paper industry generally use a combination of wet chemical analyses and physical measurements to certify the fitness of a production pulp for a specific end-use. These laboratory tests require time and the effort of trained personnel, limiting their utility for real-time process control. Here we show that Raman probes of unrefined cellulosic pulps, well-suited to the online measurement of in-process materials, can predict the quality attributes of manufactured papers. The accuracy of prediction improves when the covariance is modelled in a reduced measurement space selected by a data-driven, feature-selection technique referred to as a Template Oriented Genetic Algorithm (TOGA). TOGA, combined with discrete wavelet transform (DWT), isolates functional-group features that correlate best with mechanical properties paper derived from refined pulp. Paper makers refine market pulps to build sheet strength using a beating process that decreases freeness as it increases fibre-fibre bonding. Methods demonstrated here predict manufactured sheet properties obtainable after any specified degree of refining from the Raman spectrum of an unrefined pulp. This analysis capacity will enable both vendors of market pulp and makers of sheet paper to specify in advance the amount of beating required to produce a desired product, thereby saving cost and conserving resources.

Eco-friendly and cost-effective materials and processes to manufacture functional substrates are crucial to further advance the area of printed electronics. One potential key component in the printed electronics platform is an electrically functionalized paper, produced by simply mixing common cellulosic pulp fibers with high-performance electroactive materials. Herein, an electronic paper including nanographite has been prepared using a standardized and scalable papermaking technique. No retention aid was needed to achieve a conducting nanographite loading as high as 50 wt %. The spontaneous retention that provides the integrity and stability of the nanographite paper, likely originates partially from an observed water-stable adhesion of nanographite flakes onto the fiber surfaces. The resulting paper exhibits excellent electrical characteristics, such as an in-plane conductivity of 107 S/cm and an areal capacitance of 9.2 mF/cm(2), and was explored as the back-electrode in printed electrochromic displays. Funding Agencies|Digital Cellulose Centre, a competence center set up by the Swedish Innovation Agency VINNOVA; consortium of Swedish forest industries; Wallenberg Wood Science Center (Knut and Alice Wallenberg Foundation); VINNOVA "EPIC" projectVinnova [2017-05413]; Karl-Erik Onnesjo Foundation

An industry compatible chemo-refining approach was tested for preparation of micro-nanofibrillated cellulose (MNFC) from bleached softwood pulp using sodium meta-periodate and sodium chlorite as oxidizers followed by refining in Valley beater. SEM and FTIR analyses confirmed micro-nano scale fibrillation and chemical functional group modification in laboratory prepared MNFC, respectively. The water retention value, carboxyl content and viscosity of MNFC were found comparable with imported NFC as reference (R-NFC). To evaluate MNFC as strength enhancer for paper properties, 5% MNFC addition to bleached mixed hardwood pulp showed 6% reduction in bulk with 36%, 24% and 97% increment in breaking length, burst index and double fold of the handsheets, respectively without affecting tear index and optical properties than the control. Surface properties were also improved. Pulp drainability (37°SR) after MNFC addition was found suitable for papermaking. These laboratory results confirmed the potential of MNFC as a suitable strength additive for paper quality improvement.

In this study, a microfluidic paper-based analytical device (mu PAD) was integrated with a smartphone app capable of offline (without internet access) image processing and analysis for the rapid colorimetric detection of glucose. A self-inking stamp was used to form hydrophobic channels on a piece of paper-towel due to its superior water absorption efficiency. As demonstrated, the developed sensor was employed for the colorimetric detection of glucose in artificial saliva in the linear scope of 0 - 1 mM with a calculated detection limit of 29.65 mu M. The experimental results show that the quantitative analysis of glucose with the proposed smartphone platform could be completed in less than one minute. The app developed for the smartphone platform is capable of extracting the color-changing area with an embedded image processing tool which could address the problem of color uniformity in the detection zones of mu PAD. The integrated platform has great potential to be used for non-invasive measurements of glucose in body fluids, like tears, sweat and saliva.

Photocatalytic materials have been widely used to remove dyes from printing and dyeing wastewater. However, difficulty in recycling of photocatalysts is the great concern in the real catalytic applications, which significantly raises the application cost. This study developed a low-cost catalyst by loading magnetic Ni onto filter paper (FP) via an easy going in-situ reaction. The characterization results displayed that the Ni particles were uniformly anchored onto the FP. The Ni@FP material presented a strong magnetic ability which was evidenced by a saturation magnetization (Ms) of 5.014 emu·g−1, a remanent magnetization (Mr) of 2.067 emu·g−1 and a coercivity (Hc) of 133.868 Oe. Meanwhile, the magnetic Ni@FP material displayed a recyclable advantage in photocatalytic degradation of methyl orange (MO) via an external magnetic field. There existed an optimal photocatalytic degradation rate of 93.40% within 5 min when MO concentration was 15 mg·L−1 at pH 8.0. Three cycle experiments confirmed that the Ni@FP possessed a satisfied stability and recycling ability. Moreover, the Ni@FP material presented a strong antibacterial activity which can prevent it from being contaminated by microorganisms. The versatility of the newly proposed photocatalyst in this study demonstrated its great application prospect in dyeing wastewater treatment.

Made available in DSpace on 2021-06-25T10:45:32Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-01-25 Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) Fundação de Amparo à Pesquisa do Estado de Minas Gerais (FAPEMIG) Lactose (LAC) is a disaccharide - major sugar, present in milk and dairy products. LAC content is an important indicator of milk quality and abnormalities in food industries, as well as in human and animal health. The present study reports the development of an innovative imprinted voltammetric sensor for sensitive detection of LAC. The sensor was constructed using electropolymerized pyrrole (Py) molecularly imprinted polymer (MIP) on graphite paper electrode (PE). The MIP film was constructed through the electrosynthesis of polypyrrole (PPy) in the presence of LAC (template molecule) on PE (PPy/PE). To optimize the detection conditions, several factors affecting the PPy/PE sensor performance were assessed by multivariate methods (Plackett–Burman design and central composite design). Under optimized conditions, the proposed analytical method was applied for LAC detection in whole and LAC-free milks, where it demonstrated high sensitivity and selectivity, with two dynamic linear ranges of concentration (1.0–10 nmol L−1 and 25–125 nmol L−1) and a detection limit of 0.88 nmol L−1. The MIP sensor showed selective molecular recognition for LAC in the presence of structurally related molecules. The proposed PPy/PE sensor exhibited good stability, as well as excellent reproducibility and repeatability. Based on the results obtained, the PPy/PE is found to be highly promising for sensitive detection of LAC. Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Institute of Exact and Natural Sciences of Pontal Federal University of Uberlandia, 1600 20 St., Ituiutaba, Minas Gerais State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State FAPESP: 2017/25329–6 FAPESP: 2018/12131–6 FAPESP: 2019/13818–8 CNPq: 408783/2018–4 CNPq: 443315/2014–0 CNPq: 447668/2014–5 CAPES: 88887.368610/2019–00 FAPEMIG: APQ-02078-15 FAPEMIG: APQ-02905-15

Silver nanoparticle (AgNP)-decorated cellulose filter paper (FP), a low-cost point-of-use (POU) water disinfection system, can supply affordable and safe drinking water for people in desperate need, especially in rural areas in developing countries. However, owing to the unstable immobilization of AgNPs, silver can leach into the treated drinking water from the FP and exceed the World Health Organization (WHO) drinking water limit (

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein, we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including a pressure of 3.8 MPa, temperature of 80 °C, and 3 min of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. The wicking speed in the fabricated paper strips was slightly lower than that of non-processed paper, resulting from a reduced paper pore size after hot pressing. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in a two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper devices from this fabrication process are potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

info:eu-repo/grantAgreement/EC/H2020/787410/EU The work was also partially funded by the Nanomark collaborative project between INCM (Imprensa Nacional - Casa da Moeda). Publisher Copyright: © 2021 The Author(s). Published by IOP Publishing Ltd. Titanium dioxide nanoparticles and nanostructured thin films were simultaneously synthesized using a microwave-assisted hydrothermal method. The synthesis formed very fine particles, appearing as nanospheres in the 11 nm size range. As for the nanostructured films, they have displayed similar structural characteristics to the nanoparticles, with thickness of 130 nm. These films covered uniformly and homogenously the Whatman paper, while maintaining its flexibility. The materials processed had their photocatalytic activity assessed from rhodamine B degradation under solar radiation (91% degradation after 40 min for the powder material and 68% after 6 h for the nanostructured thin films). Reusability experiments were also carried out, revealing superior performance concerning the Degussa P25, the most common photocatalyst used. The results of the present work can be thought as an option for the existing photocatalysts activated under solar light, namely for water purification, as it simultaneously produces enhanced photocatalytic powders and photocatalytic papers fully disposable and that can be easily recycled. publishersversion published

Paper is a common material that is promising for constructing microfluidic chips (lab-on-a-paper) for diagnostics and drug delivery for biomedical applications. In the past decade, extensive research on paper-based microfluidics has accumulated a large number of scientific publications in the fields of biomedical diagnosis, food safety, environmental health, drug screening and delivery. This review focuses on the recent progress on paper-based microfluidic technology with an emphasis on the design, optimization and application of the technology platform, in particular for medical diagnostics and drug delivery. Novel advances have concentrated on engineering paper devices for point-of-care (POC) diagnostics, which could be integrated with nucleic acid-based tests and isothermal amplification experiments, enabling rapid sample-to-answer assays for field testing. Among the isothermal amplification experiments, loop-mediated isothermal amplification (LAMP), an extremely sensitive nucleic acid test, specifically identifies ultralow concentrations of DNA/RNA from practical samples for diagnosing diseases. We thus mainly focus on the paper device-based LAMP assay for the rapid infectious disease diagnosis, foodborne pathogen analysis, veterinary diagnosis, plant diagnosis, and environmental public health evaluation. We also outlined progress on paper microfluidic devices for drug delivery. The paper concludes with a discussion on the challenges of this technology and our insights into how to advance science and technology towards the development of fully functional paper devices in diagnostics and drug delivery.

There is growing demand for simple to operate, sensitive, on-site quantitative assays to investigate concentrations of drug molecules in pharmaceutical preparations for quality assurance. Here, we report on the development of two colorimetric analysis methods for the study the antibiotic doxycycline hyclate (DOX) and the nasal decongestant oxymetazoline hydrochloride (OXY), in solution as well as in their respective formulations. We compare a UV/vis spectrophotometry method with a color change recorded on a microfluidic paper-based analytical device (μPAD). Detection is based on the pharmaceutical compounds coupling with diazotized 4-aminoacetophenone (DAAP) under alkaline conditions to produce colored azo-dye products. These azo-compounds were monitored by absorbance at 425 nm for DOX and 521 nm for OXY, with linear calibration graphs in the concentration range of 0.5–35 mg L−1 (DOX) and 1.0–40 mg L−1 (OXY) and limits of detection of 0.24 mg L−1 (DOX) and 0.32 mg L−1 (OXY). For the μPAD method, color intensity was measured from photographs and a linear increase was observed at concentrations from above approximately 15 mg L−1 for both compounds and up to 35 mg L−1 for DOX and 40 mg L−1 for OXY. The developed methods were also applied to the formulated pharmaceuticals and no interference was found from the excipient. Thus, the paper-based device provides an inexpensive, simple alternative approach for use outside centralized laboratories with semi-quantitative capability.

The growing need for reliable analytical tools to perform measurements at the point-of-need has prompted the development of novel sensors that are low cost, portable, sensitive, easy to use, and capable of multiplexed analysis. Miniaturization of the sensors into microfluidic platforms has become a promising approach to achieve these self-contained sensors. However, traditional microfluidics often require relatively expensive and complicated pumping mechanisms that increase the cost and limit the portability of the sensors. From a material perspective, paper is an attractive substrate for constructing point-of-need sensors because of its affordability, vast availability, and self-pumping ability, particularly when combined with electrochemical detection. In this mini-review, we discuss various strategies to achieve multiplexing or simultaneous detection of multiple analytes in electrochemical paper-based devices and provide a brief guide on selecting the detection strategy based on the electrochemical property of the analytes.

A novel nacre-like flame-retardant paper based on graphene oxide (GO), and phytic acid (PTA) is fabricated via evaporation-induced self-assembly. This facile method is time saving and low energy consuming. A facile approach is proposed to improve thermal oxidative stability of GO paper by in situ phosphorus doping during flame exposure. Then fire-alarm system is designed based on the high-temperature thermal reduction characteristic of GO. The GO paper functionalized with PTA (GO-PTA) can provide ultrasensitive, reliable and longtime fire early-warning signal. Fire alarm can be triggered at approximately 0.50 s when GO-PTA samples are attacked by fire. Phosphorus atoms are in situ doped into graphene layers during fire exposure, endowing GO-PTA paper with outstanding thermal oxidative stability, and thus alarm duration time of GO is greatly improved. The work develops advanced fire detection and early-warning sensors that provide reliable and continuous signals, which provide more available time for fire evacuation.

The sensitive quantitative analysis of trace heavy metallic elements (Cd, Mn, Cr, and Cu) in aqueous solutions was achieved successfully through the combination of filter paper enrichment with laser-induced breakdown spectroscopy. Filter paper was enriched with 0.4 mL aqueous solutions to form a homogeneous sample layer on the surface of the metallic target. Considering the limits of detection, the values deduced with calibration curves already exhibited the high performance of the proposed method at several hundred or 10 μg/L (Cd 0.165, Mn 0.035, Cr 0.012, and Cu 0.078 mg/L), lower than or comparable to those using other similar methods. The LIBS results agreed reasonably well with those from ICP-MS for real samples. All results showed that our method was suitable and accurate for rapid on-site detection of trace metals in aqueous solutions. This indicates that filter paper enrichment combined with laser-induced breakdown spectroscopy is a feasible approach to wastewater quality monitoring.

Simultaneous enhancement in water flux and removal efficiency during the filtration process remains a big challenge for separation membranes. The porous structure of the filter paper can provide many channels for water transportation, but the separation performance is generally poor. The purpose of this study is to develop a new kind of filter paper consisting of ultralong hydroxyapatite (HAP) nanowires, cellulose fibers (CFs) and double metal oxide (LDO) nanosheets, and to achieve the simultaneous enhancement of both water flux and removal efficiency for high-performance dye separation. In this work, a novel kind of LDO/HAP/CF nanocomposite filter paper consisting of ultralong HAP nanowires and CFs and LDO nanosheets has been developed for rapid water filtration and highly efficient dye adsorption. Positively charged LDO nanosheets can adsorb on the surface of negatively charged ultralong HAP nanowires and embed in the porous networked structure of the LDO/HAP/CF nanocomposite filter paper, which can provide a porous structure for rapid water transportation and can adjust the pore size of the nanocomposite filter paper. As a result, the pure water flux of the LDO/HAP/CF nanocomposite filter paper can be adjusted. The optimized pure water flux of the LDO/HAP/CF nanocomposite filter paper can reach 783.6 L m-2 h-1 bar-1, which is 1.51 times that of the HAP/CF filter paper without LDO nanosheets (518.6 L m-2 h-1 bar-1). More importantly, the adsorption capacity of LDO nanosheets is high for dye molecules, the rejection percentage of Congo red (CR) by the as-prepared HAP/CF filter paper is only 59.8%, and its water flux is 534.7 L m-2 h-1 bar-1. The optimized rejection percentage and water flux of the LDO/HAP/CF nanocomposite filter paper for CR are significantly enhanced (98.3% and 736.8 L m-2 h-1 bar-1, respectively) compared to those of the HAP/CF filter paper. The size of LDO nanosheets has a significant effect on the water flux and dye rejection percentage of the LDO/HAP/CF nanocomposite filter paper. The as-prepared LDO/HAP/CF nanocomposite filter paper is promising for the applications in highly efficient purification of wastewater containing dye molecules.

Nickel nanoparticles supported by commercial carbon paper (CP) are prepared by pulsed laser deposition with deposition time of 3, 6, and 12 min as a catalyst for urea electro-oxidation. The surface conditions and the morphologies of the prepared electrodes have been characterized by Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Urea electro-oxidation reaction in KOH solution on the Ni/CP electrodes is investigated by cyclic voltammetry and chronoamperometry. The results show that the electrode with less Ni nanoparticle agglomeration shows higher peak current density, which was achieved in the 3 min deposition samples when normalized by electroactive surface areas. However, the highest current normalized by the area of the carbon paper was achieved in the 6 min deposition sample due to the larger quantity of Ni nanoparticles. All the samples show good stability. Our results suggest that the low density, low cost, and environmental friendly CP can be used as support for Ni nanoparticle as a catalyst for urea electro-oxidation. It thus has great potential for many applications involving urea oxidation, such as wastewater treatments.

Over the past decades, paper-based lateral flow immunoassays (LFIAs) have been extensively developed for rapid, facile, and low-cost detection of a wide array of target analytes in a point-of-care manner. Conventional home pregnancy tests are the most significant example of LFAs, which detect elevated concentrations of human chorionic gonadotrophin (hCG) in body fluids to identify early pregnancy. In this work, we have upgraded these platforms to a higher version by developing a customized microfluidic paper-based analytical device (μPAD), as the new generation of paper-based point-of-care platforms, for colorimetric immunosensing. This will offer a cost-efficient and environmentally friendly alternative platform for paper-based immunosensing, eliminating the need for nitrocellulose (NC) membrane as the substrate material. The performance of the developed platform is demonstrated by detection of hCG (as a model case) in urine samples and subsequently indicating positive or negative pregnancy. A dual-functional silane-based composite was used to treat filter paper in order to enhance the colorimetric signal intensity in the detection zones of μPADs. In addition, microfluidic pathways were designed in a manner to provide the desired regulated fluid flow, generating sufficient incubation time (delays) at the designated detection zones, and consequently enhancing the obtained signal intensity. The presented approaches allow to overcome the existing limitations of μPADs in immunosensing and will broaden their applicability to a wider range of assays. Although, the application of the developed hCG μPAD assay is mainly in qualitative (i.e., positive or negative) detection of pregnancy, the semi-quantitative measurement of hCG was also investigated, indicating the viability of this assay for sensitive detection of the target hCG analyte within the related physiological range (i.e., 10–500 ng/mL) with a LOD value down to 10 ng/mL.

Lithium-ion (Li-ion) batteries have been fabricated in various ways to improve flexibility. Flexibility could be enhanced via active materials, separators, electrodes, and electrolytes, which could then be integrated to form flexible electronic devices with promising electrochemical properties compared to traditional non-flexible Li-ion batteries. Recent progress towards flexible Li- ion batteries fabrication, materials, and their electrochemical properties are investigated in this review. Additionally, recent developments in electronic devices utilizing flexible batteries and their future applications are explored. Portable and wearable electronics, as the primary beneficiaries of the flexible, rechargeable, and high-performance Li-ion batteries, are examined. In the end, various applications and challenges of flexible batteries in healthcare and various energy storage systems, considering practical implementation, are argued.

Inorganic salt modified paper substrates were developed and utilized in microfluidic paper based sampling coupled with potentiometric ion sensors for the determination of heavy metals, such as Cd2+ and Pb2+. The application of paper based sampling without any paper substrate pre-treatment were characterized with super Nernstian response, while the paper substrates with inorganic salt pre-treatment were characterized with standard Nernstian response. The application of inorganic salt modified paper substrates was found advantageous when the cation of the salt in the conditioning solution was the same as the primary cations of the ion-selective electrodes (ISEs). A relatively high concentration of inorganic salts during pre-treatment of the paper substrates, namely Cd(NO3)2 or Pb(NO3)2 with subsequent measurement of cadmium(II) and lead(II), by Cd2+- and Pb2+-ISEs, respectively was needed to sustain Nernstian response of sensors. It was also found that paper substrates facilitate sorption of metal ions onto the paper substrates, with stronger binding strength given to Pb2+ over Cd2+. Moreover, the metal-paper interactions suggest concentration dependent sorption-desorption of metal ion, which can have direct limitations of the use of paper based analytics for the determination of low analyte concentration of heavy metals. Nanyang Technological University The authors would like to thank NTU-India Connect Research Internship Program for financial support of Ms Tharini Saravana Sundaram from Coimbatore Institute of Technology, India.

Abstract Tissue paper softness relies on two major factors, the bulk softness, which can be indicated by the elasticity of the sheet, and surface softness. Measurement of surface softness is complicated and often requires a multi-step process. A key parameter defining surface softness is the topography of the surface, particularly the crepe structure and its periodicity. Herein, we present a novel approach to measure and quantify the tissue paper surface crepe structure and periodicity based on the detection of waviness along the sample using laser scanning confocal microscopy (LSM) and X-ray tomography (XRT). In addition, field emission scanning electron microscope (FESEM) was used to characterize the tissue paper surface. We demonstrate that surface topography is directly correlated to the erosion of the doctor blade, which is used to remove the dry tissue paper from the Yankee cylinder. Because of its accuracy and simplicity, the laser confocal microscopy method has the potential to be used directly on the production line to monitor the production process of the tissue paper. XRT revealed more structural details of the tissue paper structure in 3D, and it allowed for the reconstruction of the surface and the internal structure of the tissue paper. Graphic abstract

A superhydrophobic paper with excellent robustness was fabricated by roll coating with modified nano-TiO2. First, nano-TiO2 particles were hydrophobically modified by γ-aminopropyltriethoxysilane and 1H, 1H, 2H, 2H-perfluorooctyltriethoxysilane (POTS). Then the paper coating composed of modified nano-TiO2 particles as pigments and epoxy resin (EP) as adhesives was coated on a paper surface to create the desired surface morphology and surface energy. Compared with the uncoated filter paper, the prepared paper showed an improved rough surface morphology owing to the uniform layer of TiO2 microclusters deposited on the fiber network. The superhydrophobic paper exhibited water contact angles (WCA) about 153° ± 1.5°, and water sliding angles (WSA) about 3.5° ± 0.5°, low surface adhesion and excellent bounce ability. The superhydrophobic paper can withstand a variety of wear and tear, such as tape stripping and knife scraping. The as-prepared superhydrophobic paper showed mechanical durability even after 20 wear cycles with sandpaper,thus sustaining excellent superhydrophobicity on the filter paper surface. Moreover, it remains fully functional even in environments with high concentrations of acid and alkali for 96 h. The superhydrophobicity was not affected after storage for 6 months in a natural environment. It was confirmed that the superhydrophobic paper surface exhibited excellent chemical stability, long-term stability and self-cleaning properties. The entire production process was operated under normal environment, without complex equipment; and, as such, has the possibility for large-scale production and application in industry.