Search

Lime mud, a kind of industrial waste that produced in paper mill, was proposed as CO2 sorbent in calcium looping process. The carbonation performance of the lime mud was investigated in a dual‐fixed bed reactor (DFR) and a thermogravimetric analyzer (TGA). The carbonation kinetics of the lime mud in the chemical reaction controlled stage was analyzed by a surface reaction‐controlled kinetic model. The results show that the lime mud presents much poorer carbonation performance during the chemical reaction controlled stage compared with the limestone, mainly due to the high content of chlorine in the lime mud. A prewash treatment process was used to decrease the chlorine content to mitigate the sintering of the lime mud when calcined at high temperature. After prewash treatment, the prewashed lime mud shows much higher CO2 capture capacity during the chemical reaction controlled stage compared with the lime mud. A prolonged carbonation process successfully further enhances the microstructure and improves the carbonation performance of the prewashed lime mud in the chemical reaction controlled stage. The lime mud can be effectively used as CO2 sorbent in calcium looping process after prewash treatment and the following prolonged carbonation treatment.

Sweden is one of the largest exporters of pulp and paper products in the world. It follows that huge quantities of sludge rich in carbonaceous organic material and containing heavy metals are generated. This paper carried out a comparative environmental analysis of three different technologies, which can be adopted to produce biochar and recover energy from the biosludge, using landfilling as the reference case. These three thermochemical biosludge management systems—using incineration, pyrolysis, and hydrothermal carbonization (HTC)—were modeled using life cycle assessment (LCA). Heat generated in the incineration process (System A) was considered to be for captive consumption within the kraft pulp mills. It was assumed that the biochars—pyrochar and hydrochar—produced from pyrolysis (System B) and HTC (System C), respectively, were added to the forest soils. The LCA results show that all the alternative systems considerably improve the environmental performance of biosludge management, relative to landfilling. For all systems, there are net reductions in greenhouse gas emissions (–0.89, –1.43, and –1.13 tonnes CO 2 -equivalent per tonne dry matter biosludge in Systems A, B, and C, respectively). System B resulted in the lowest potential eutrophication and terrestrial ecotoxicity impacts, whereas System C had the least acidification potential. The results of this analysis show that, from an environmental point of view, biochar soil amendment as an alternative method for handling pulp and paper mill biosludge is preferable to energy recovery. However, an optimal biochar system needs to factor in the social and economic contexts as well.

This Editorial introduces a Special Issue of papers from the SEE International Conference RADAR 2019, which took place in Toulon, France, 23–27 September 2019. The papers are expanded versions of ones that were judged in the reviewing process to be of the highest quality and relevance. Benefitting from the unique location of the conference centre on the French Riviera, the conference was given the theme ‘Sensing from sea to space’, attracting nearly 400 attendees from 26 countries from all over the world (Figure 1). Engineers and researchers coming from private or public sector (universities and laboratories) shared their knowledge and experience on radar topics of common interests from physics to signal processing, from sensor validation to system design, and also on emerging technologies based on artificial intelligence; all topics being supported by 200 papers presented either in oral (150 papers in 36 sessions), or poster sessions (50 papers). Figure 2 shows the range of topics of the papers. 1 FIGURE Conference attendees by country 2 FIGURE Conference paper topics

This is a review of the literature published in 2018 related to the prevention of water pollution by or recovery of beneficial materials from wastewater produced in the pulp and paper industry. This review includes the following main sections: cleaner production, biological treatment, and physico-chemical treatment. PRACTITIONER POINTS: Converting pulp and paper treatment sludges to value-added materials can be efficient cleaner production technique. Modeling and dynamic simulation techniques of biological treatment along with optimization methods can improve the effluent quality out of a paper mill. Hybrid treatment systems can have a synergistic effect on the treatment of pulp and paper effluents.

To relief the water shortage crisis in China, the Chinese government has initiated a series of clean production (CP) measures to reduce the freshwater consumption and wastewater discharge from paper industry. In this study, a new CP technology was introduced in the paper industry to reuse tissue paper mill effluent water as intake water of corrugated paper mill. The feasibility and impact of the new CP technology was investigated in three different scales, laboratory experiments, pilot-scale testing, and long-term implementation. Results show that the water quality of treated tissue paper mill effluent water is competitive with that of freshwater and some water quality indexes are even better, indicating that treated tissue paper mill effluent water is a suitable alternative to replace the freshwater as intake water for the corrugated paper mill. By reusing tissue paper mill effluent water as intake water of corrugated paper mill, most physical properties of different corrugated paper layers are improved or similar as those by using freshwater as intake water in all different scale experiments. Moreover, the new CP technology significantly reduced the freshwater consumption for the corrugated paper mill, eliminated the wastewater discharged from the tissue paper mill, and at the same time, lowered the operation cost for both paper mills in terms of freshwater consumption and wastewater treatment cost. Total 216,000 RMB will be saved every year with an assumption that tissue paper mill provides annual daily average 2000 cubic meter of effluent water to corrugated paper mill every day. © 2017 American Institute of Chemical Engineers Environ Prog, 2017

This study sought to verify the readability of e-paper devices under various conditions. The experimental conditions included various stages of illuminance, different font sizes, and different contrasts. More than 100 participants participated in the experiments from the young to the elderly. The subjects read and compared the e-paper, backlit LCD, and conventional paper under the various conditions.

A novel paper‐based biofuel cell with a series/parallel array structure has been fabricated, in which the cell voltage and output power can easily be adjusted as required by printing. The output of the fabricated 4‐series/4‐parallel biofuel cell reached 0.97±0.02 mW at 1.4 V, which is the highest output power reported to date for a paper‐based biofuel cell. This work contributes to the development of flexible, wearable energy storage device.

The United States Environmental Protection Agency (EPA) developed Toxic Release Inventory (TRI) using information submitted by different industries in the United States. This research examines the contaminants released by paper manufacturing industry in the United States and Ohio over time and what paper manufacturers are doing to diminish the quantities of chemical wastes generated, released to the environment, or managed by other means. It is understood that there is a reduction in the Risk-Screening Environmental Indicators (RSEI) scores from 2002 to 2014 in all the states, which can be related to the adaptation of recycling or reusing of the chemicals in various other manufacturing processes. The other significant observation inferred from the analysis is that the facilities in the states such as Wisconsin, Louisiana, South Carolina, Connecticut, and Pennsylvania based on the economic feasibility or recycling prospects, they are generating higher quantities of the selected chemical resulting in the higher RSEI scores respectively for the above-mentioned states. This article demonstrates the application of the risk-screening indicators model to a large database to analyze pollution data. © 2017 American Institute of Chemical Engineers Environ Prog, 36: 808–814, 2017

Indented writing on thermal paper made with either one, two, or three sheets of paper above the thermal paper has been visualized by the controlled application of heat to the thermal paper at temperatures below the paper's normal color change temperature. Indentations created by applying a variable pressure to a steel letter stamp showed that, with one sheet above the thermal paper, indentations were more visible at lower pressures than with either two or three sheets above. Handwriting from 20 volunteers produced indented writing graded with most of the text clear and easy to read for all samples with one sheet above, half the samples with two sheets above and eight samples with three sheets above. Comparison with ESDA showed that, with three sheets above, there was a statistically significant difference (p < 0.01), with heating producing more samples than ESDA with most of the text clear and easy to read.

Regulatory policies to manage land application of organic materials are risk based, with focus on the quality of these residuals. The Ontario Ministry of the Environment and Climate Change (MOECC) determined that limited information was available on pulp and paper biosolids (PPB) with respect to human enteric pathogens. To address this data gap, MOECC conducted an extensive survey (2005-2006) across Ontario to characterize the microbiological quality of PPB. Quantitative testing was performed for fecal indicators (, enterococci, ) and enteric pathogens (, , , and ) using matrix-validated methods. Comparative benchmark materials (soils and soil amendments) were analyzed concurrently for risk comparison. Results showed that detection rates in PPB were low, 5 to 25% for pathogens and

This paper presents the design, manufacturing and measurements of antennas on paper, realized using ink-jetprinting of conductive inks based on nano-silver particles (nSPs). The extraction of the substrate characteristicssuch as the dielectric constant and dielectric loss is performed using a printed ring resonator technique. Thecharacterization of the nSPs conductive inks assesses different parameters as sintering time and temperature.Two antennas are realized corresponding to the most common needs for Wireless Sensor Networks (WSN) inTrains Environment. The first one is a patch antenna characterized by a broadside radiation pattern and suitedfor operation on metallic structures. The second one is a quasi-yagi antenna, with an end fire radiation patternand higher directivity, without requiring a metallic ground plane. Both antennas present a good matching (S11 < -20 dB and S11 < -30 dB, respectively) and acceptable efficiency (55 % and 45 %, respectively) for the papersubstrate used at the center frequency of 2.4 GHz, corresponding to the first channel of the IEEE 802.15.4 band.

Porous pots were used to mimic, on a laboratory scale, an industrial activated sludge plant from a thermomechanical pulp and news print paper mill. Trace metal additions of Ca, Co, Cu, Fe(III), and Mg were found to improve chemical oxygen demand removal from 82% to 86 to 87%. Copper (0.1 to 1.0 mg/L) was also found to be beneficial in significantly inhibiting the growth of filamentous bacteria, contributing to a reduction of 20 to 45% in sludge volume index (SVI) with improved settle ability and decreased bulking. However, at levels of 1.0 mg/L and higher, the concentration of Cu in the porous pot effluent would potentially exceed guidelines for receiving waters. The fate and impact of Cu was affected by the presence of other trace metals, in particular Mg and Ca. The addition of Mg or Ca along with 0.5 mg/L Cu increased the amount of Cu in the aqueous phase to levels that would potentially exceed government environmental guidelines. Calcium addition was also found to inhibit the effect of Cu in reducing filamentous bacteria and SVI.

An analytical model for low-consistency repulping linking pulp material properties, consistency, temperature, and rotor and vat geometry is provided, which allows for accurate prediction of the time and energy required for repulping in both a 0.25 m3 laboratory-scale repulper and a 15 m3 industrial-scale repulper. The model assumes that all deflaking work is done by the repulper rotor in the rotor-swept volume by turbulence generated by the rotor and that no deflaking occurs in the rest of the vat. Rotor shaft power is split linearly between the breakup of waste paper and dissipation by turbulence. Comparing the model predictions and experimental data for different pulp types, vat fill levels, and pulp suspension consistencies yields a correlation of R2 = 0.99 between all experimental results and the model predictions given the condition of fully turbulent (Reynolds-independent) repulper rotor operation. The efficiency of the laboratory repulper is reduced from that predicted by the model for very low vat fill levels. This is due to a loss of effectiveness of the baffles at these low levels as indicated by solid body motion of the suspension and reduced rotor power number. This indicates that thorough mixing is a requirement to maximize repulping efficiency. Repulping time and energy savings can be accomplished by increasing the suspension consistency and the rotor-swept volume/vat volume ratio by either increasing rotor size or reducing vat volume, all while ensuring complete mixing and circulation in the vat.

This study evaluates the treatment efficiency of a horizontal subsurface-flow constructed wetland (HSSF-CW) for the removal of chloro-organic compounds from pulp and paper mill wastewater. The surface area of the HSSF-CW unit was 5.25 m² and was planted with Colocasia esculenta. The wastewater was characterized for different chloro-organic compounds, that is, adsorbable organic halides (AOX), chlorophenolics, and chlorinated resin and fatty acids (cRFAs). Under a hydraulic retention time of 5.9 days, the average AOX, chlorophenolics, and cRFA removal from wastewater was 87, 87, and 93%, respectively. Some of the chlorophenolics were found to accumulate in the plant biomass and soil material. The mass balance studies show that a significant fraction of chlorophenolics and cRFA was degraded in the constructed wetland system. Modeling studies were carried out to estimate the first-order area-based removal rate constants (k) for chemical oxygen demand removal. The HSSF-CW was found to be an effective treatment technology for the remediation of pulp and paper mill wastewater.

The appearance or printing quality of paper surfaces is mostly characterized by their glossiness, measured with a glossmeter as specular reflectance. The gloss properties of a base paper substrate can be improved after application of a poly(styrene-co-maleimide) nanoparticle coating under pure conditions or in the presence of different vegetable oils. The specular gloss properties of 11 different nanoparticle paper coatings have been determined under 75 degrees and 85 degrees incident light angles, with good relation between values along parallel (machine) and perpendicular (transverse) direction. The gloss properties for the different coatings have been further related to the surface topography. Therefore, the statistical and spatial surface roughness parameters have been studied in detail at two length scales including non-contact profilometry (1 x 1 mm(2)) and atomic force microscopy (2 x 2 m(2)). Based on values of the Rayleigh parameter for non-contact profilometry, the surfaces can be considered as optically rough. The gloss values cannot be directly related to statistical surface roughness parameters. Otherwise, an experimental power-law model for gloss has been proposed as a function of (/Sq) with correlation length and root-mean-square roughness Sq. A best-fit model illustrates that gloss properties of various nanoparticle paper coatings mainly relate to the spatial surface roughness parameters determined from non-contact profilometry. (c) 2015 Wiley Periodicals, Inc. Col Res Appl, 41, 596-610, 2016

Latent fingerprint deposits on thermal paper sourced from the U.S., China, the U.K., and Australia have been visualized by heating. U.S. and Chinese sourced paper produced two distinct types of fingerprint development. In one type (type 1), the paper dye colors where the deposit is present (as previously reported) and in the other type (type 2) the 'inverse' of this gives paper coloring only in areas not coincident with the deposit. Both development types gave identifiable fingerprints, the majority fading within 24 h of heating. Fingerprint development from U.K. and Australian sourced paper was exclusively type 1 and resistant to fading. Temperatures for fingerprint visualization were higher for U.S. paper (64-71°C) and Chinese paper (75-95°C) than for U.K. and Australian sourced paper (43-50°C). Particularly for Chinese sourced paper, these temperatures were within a few degrees of the normal paper color temperature. A mechanism for type 2 fingerprint development is proposed.

In a rapidly urbanizing global society, the issue of solid waste management has become even more challenging in recent times. Manufacturing of paper, an integral part of human civilization, generates a substantial amount of effluent sludge, which invariably needs extra monetary resources to dispose-off in millions of tons annually around the world. Currently, most of the widely practiced disposal options, landfilling and incineration, invariably pose serious environmental risks to immediate neighborhoods as well as to society at large. Recent stricter environmental legislations and general public awareness have been forcing paper producers to follow a sustainable approach in dealing with residual biomass generated at their facilities. At the same time, reducing waste at source and recycling have become an integral part of waste management of some responsible companies and governments of the industrialized world have also taken a number of initiatives in this regard. This review presents a holistic overview on current practices in dealing with paper sludge and their environmental and economic implications. Also presented is a comprehensive discussion on emerging biorefinery trends leading to value-added utilization of primary, secondary and mixed biosolids originating from effluent treatments plants, especially from paper mill operations.

The commercialization of electronic paper displays has brought the consumer a truly comfortable and mobile viewing experience, even in bright daylight conditions. We review the display standards activities that support the quality manufacturing of these products and helps drive their market expansion.

This paper describes a new e-paper system, which is suitable for office applications. As a replacement of paper based work, it is necessary to have the same readability as paper, capability of handwriting, and convenience of IT equipment. In order to satisfy these requirements, there are three main features of this system. One is a high resolution electrophoretic display (EPD) which provides printed paper image quality. Another is binary display driving which provides high speed image writing on a high resolution display. The last is an original EPD control scheme which gives quick page turning or handwriting performance.

This work was supported by the industrial strategic technology development program funded by MKE/KEIT under grants 10079974 and Samsung research funding center for future technology through Samsung Electronics

The application of industrial residuals in agriculture may raise concerns about soil and crop metal accumulation. A complete study using a fractionation scheme would reveal build-up in metal pools occurring after material addition and predict the transformation of metals in soil between the different forms and potential metal release into the environment. An experimental study was conducted from 2000 to 2008 on a loamy soil at Yamachiche, Quebec, Canada, to evaluate the effects of repeated annual addition of combined paper mill biosolids when applied alone or with several liming by-products on soil Cu, Zn, and Cd fractions. Wet paper mill biosolids at 0, 30, 60, or 90 Mg ha and calcitic lime, lime mud, or wood ash, each at 3 Mg ha with 30 Mg paper mill biosolids ha, were surface applied after seeding. The soils were sampled after 6 (soybean [ (L.) Merr.]) and 9 [corn ( L.)] crop years and analyzed using the Tessier fractionation procedure. Results indicated that biosolids addition increased exchangeable Zn and Cd, carbonate-bound Cd, Fe-Mn oxide-bound Zn and Cd, organically bound Cu and Zn, and total Zn and Cd fractions but decreased Fe-Mn oxide-bound Cu in the uppermost 30-cm layer. With liming by-products, there was a shift from exchangeable to carbonate-bound forms. Even with very small metals addition, paper mill and liming materials increased the mobility of soil Zn and Cd after 9 yr of application, and this metal redistribution resulted into higher crop grain concentrations.