Search

Mineral oil has traditionally been used as a cooling fluid in power transformers, but its low biodegradability and low fire point have motivated the search of alternatives. In this work, six different dielectric fluids have been studied, including four vegetable liquids, from sunflower, rapeseed, soybean, and palm, one synthetic ester and a mineral oil used for comparison. These oils were subjected to an accelerated thermal ageing in glass vessels at 150°C for four weeks (672 hours) in presence of Kraft insulating paper. Different oils parameters were measured during the ageing, i.e. breakdown voltage, dielectric dissipation factor, permittivity, DC resistivity, density, kinematic viscosity, flash and fire points, interfacial tension, acidity, and dissolved gases; additionally, the degree of polymerisation (DP) of the paper was measured. Results showed that the changes of the natural esters properties, except for the palm oil, were similar along the ageing time. Palm oil results were similar to those of the mineral oil, whereas synthetic ester showed a behaviour similar to natural esters. The kraft paper degradation was higher in the mineral oil, followed by the synthetic ester and the palm oil. No significant differences were found in the ageing with the natural esters. This work was supported in part by the European Union’s Horizon 2020 Research and Innovation Program, through the Marie Sklodowska-Curie, under Grant 823969, and in part by the Ministry of Economy, through the National Research Project: Gestión del Ciclo de Vida de Transformadores Aislados con Fluidos Biodegradables, under Grant PID 2019-107126RBC22.

Temperature compensation occupies a significant function in the insulation condition evaluation of converter transformer bushings based on the Frequency Domain Spectroscopy (FDS), which could influence the accuracy of its insulation diagnosis. In order to accurately obtain the variation law of FDS at different temperature, a Resin Impregnated Paper (RIP) insulation bushing for converter transformer was designed by the equivalence of maximum electric field, coaxial cylinder structure and RIP materials. The increment law of dielectric parameters both dissipation factor and capacitance at wideband frequency (1mHz ~ 10kHz) was measured for a quality RIP insulation samples at the temperature from 30°C to 100°C. 1) Under the uniform temperature, it was found that the value of dissipation factor was rising with the frequency from 10 Hz to 0.001Hz, while the tendency was reversed at the frequency from 100Hz to10kHz. 2) The minimum value of tan $\delta $ from 0.001Hz to 10kHz could be driven to higher frequency moving (10Hz to 10kHz) by the action of temperature rising 30°C to 100°C.3) The effect of temperature on the lower frequency 0.001Hz ~ 1Hz tan $\delta $ of RIP insulation closely conformed to the index law of Arrhenius equation, while it was in accordance with the linear decrease at higher frequency 1kHz ~ 10kHz. The effect of temperature on dissipation factor could be eliminated by curve segment shifting based the experiment equation, which it at 0.001Hz dissipation factor could be eliminated by curve shifting based the index equation originated Arrhenius equation. The method is beneficial to eliminate the influence of temperature on the dielectric spectroscopy test results, and then to eliminate the influence of temperature on the dielectric spectroscopy diagnosis of RIP bushings.

Transmission schemes taking both sum rate and fairness into account for dirty paper coding (DPC) based MIMO downlink communications are investigated in this paper. In contrast to existing works which have mostly focused on maximizing the sum rate, we first investigate the problem of finding the maximal sum rate achieved by DPC when the qualitative notions of fairness such as max-min fairness and proportional fairness are employed. This corresponds to a nonconvex problem and cannot be solved by usual weighted sum rate techniques. Several efficient methods for finding the optimal solutions are presented in this paper when the order of users is adjustable during DPC encoding. Simulation results show surprisingly and impact greatly on the design of practical systems that it is often possible to achieve the sum rate capacity with absolute fairness, i.e., an equal rate for each user, when multiple encoding orders of users are used during transmission. When sum rate capacity and absolute fairness cannot be achieved at the same time, the optimal tradeoff between sum rate and fairness is also provided for a general class of quantitative fairness measures.

The main purpose of this paper is to present the methodology for calculating the electromagnetic behaviour of real integrated circuit (IC) parts using a no-mesh local Finite Differential Method (FDM). Furthermore, the comparison of computational results and measurements is presented. All considerations are based on typical long transmission lines (TLs) in modern ICs. The obtained results have been analysed in detail and compared with measured values. The measurement data are de-embedded using the test board model. This problem is illustrated in this paper based on a practical example of the Multi-Conductor Transmission Lines test structure whose electrical responses to various excitations are presented and analysed in detail.

With the wide application of vegetable insulating oil in power transformers, it is essential to investigate the influence of moisture on the frequency domain dielectric spectrum (FDS) analysis in order to propose an accurate moisture assessment method for vegetable oil-paper insulation system. In this regard, various vegetable oil-paper samples are prepared in a laboratory environment. FDS curves for all samples are obtained at different moisture contents and operating temperatures. A new method to estimate the moisture content in insulation paper is proposed based on the low-frequency characteristic quantity. Also, the effect of operating temperature and water migration between the oil and paper insulation on the FDS analysis is investigated. Based on this analysis, a compensation factor is introduced to eliminate the influence of temperature on paper moisture assessment. Furthermore, an improved normalization method for the temperature effect on the FDS of vegetable oil-paper insulation with different moisture contents is proposed. The proposed moisture assessment and temperature normalization methods are validated thorough their application on an operating power transformer.

Oil-paper insulation as an irreplaceable insulation system in the electrical power transformer is inevitably suffering the water intrusion on working condition, which will make dielectric performance degraded and insulation aging accelerated. In high interest of explaining the deterioration effect of absorbing moisture on the dielectric properties of oil-paper insulation system and corresponding mechanism, the space charge and trap level characteristics are investigated for the specially prepared oil-impregnated pressboards with different moisture contents. The Pulsed Electro Acoustic and Isothermal Surface Potential Decay experiments are performed to test the space charge distributions and evaluate the trap level depths, respectively. It is indicated that the polarity of injected space charges is alternated with the decaying rate being raised when the absorbing moisture is aggravated in oil-impregnated pressboards. The charge carriers are more prone to be captured by the shallow-level traps that have been introduced by water permeation near pressboard surface than the intrinsic deep-level traps inside pressboard. The captured charge carries accounts for the significantly exacerbated space charge accumulation as manifested by the surface charges of oil-impregnated pressboards.

For current steganalysis of the image content-adaptive steganography, there are multiple problems to be improved, such as high difficulty and low accuracy, when detecting images with various contents and textures. For this problem, an improved steganalytic method is proposed in this paper based on the pre-classification and feature selection. First, using the features extracted based on the dependency analysis of image adjacent data, the images with various content and texture complexities are pre-classified as multiple clusters by the K-means algorithms. Then, the performance of existing various steganalytic features are analyzed for different clusters of images, and the optimal features for each cluster are selected for final classification. The experimental results show that the detection accuracy could be improved by the proposed method, and the rationality and availability are also verified. At the same time, the analysis and experimental results in this paper also show that the images with rich content and complex texture should be paid more attention both in steganography and in steganalysis.

Power transformers are considered as one of the main parts of any power system. Because of their importance and high cost, it is important to check the state of the insulation system inside them from time to time. Dissolved gas analysis test as well as Furan compounds analysis has been widely used as recommended methods to assess the transformer insulation system state. This paper introduces an empirical form that can predict the degree of polymerization of the paper insulation system inside the transformer by measuring Furan compounds. This proposed empirical form is validated by comparing its results with other methods reported in the literature in two different case studies. Subsequently, the proposed formula is used to predict the lifetime and the insulation system state of a transformer that operates in Abo Sultan steam power plant in Egypt. The 2-FAL had been measured five times for this transformer in the period between 2013 and 2015. Depending on these five measurements, an equation that can predict 2-FAL level inside this transformer in relation to its age has been proposed. This proposed equation is validated by comparing the measured and estimated 2-FAL in the period between 2016 and 2019. According to the attained results, it was found that the insulation system inside the investigated transformer seems to face a serious problem and this transformer cannot remain in service after 2027. Finally, the paper introduced a general technique that can be used for any transformer in order to predict its remaining lifetime.

Delivering confidential messages in wireless network is gaining continuous attraction as a fundamental building block for the Internet of things (IoT). This paper overviews the confidential message transmission techniques in broadcast channel (BC) where a transmitter serves multiple users by delivering confidential messages to their intended users. Each confidential message must be prevented from extracting its information by any unintended users. First, we consider a basic network consisting of two users. In the two-user BC, the secret dirty paper coding (S-DPC) achieves the secrecy capacity region. However, since the DPC requires a high computational complexity for characterizing the capacity region, two sub-optimal transmission techniques with low complexities are explained. Second, we extend our discussion to the network including more than two users. For $K$ -user BC with confidential messages, the optimal transmission scheme and the secrecy capacity region have not yet been derived. Instead of presenting the optimal scheme, we explain two sub-optimal transmission techniques and compare their features and performances. In conclusion, we discuss the open problems in the confidential message transmission for networks with more than two users.

Recently, it has been shown that channel feedback helps to enhance the physical layer security (PLS) of communication systems. The current use of feedback focuses on generating secret keys protecting the transmitted messages, and this feedback scheme is proved to be optimal for some physically degraded channel models. In this paper, we revisit the model of the state-dependent wiretap channel with the noncausal state at the transmitter, which plays an important role in the PLS of the wireless communication systems. We propose a new feedback scheme for this model and show that the proposed new scheme performs better than the already existing secret key-based feedback scheme. The results of this paper are further explained via a Gaussian example.

Voice-over IP (VoIP) technology is a kind of digital transmission technology based on IP network. It is one of the important methods to use voice service in VoIP as steganographic carrier to ensure secure transmission. However, the traditional steganographic code has some problems, such as low embedding efficiency and weak concealment, which cannot meet the requirements of VoIP streaming media information hiding for the security of secret information. Therefore, a steganographic algorithm combining F5 and simplified wet paper code (SWPC) algorithm is proposed. The main idea is to embed secret messages in each row of the carrier matrix using the F5 algorithm, and then the SWPC algorithm is used to embed the columns according to the wet and dry characteristics of the wet paper code without affecting the results before row embedding. We use the VoIP streams encoded by the ITU-T G.729a codec as a carrier to verify the proposed scheme. The experimental results demonstrate that the proposed scheme can achieve relatively better IP speech data steganographic transparency and that it can outperform F5-WPC and SWPC approaches.

This paper investigated the influence of paper-wrapped on the deposition of sulfur corrosion on the insulation winding (paper-wrapped copper conductor) in oil-immersed insulation containing dibenzyl disulfide (DBDS). The distribution of sulfur corrosion deposit on a 500-kV electric reactor was investigated and analyzed, and the properties of oil were analyzed. Aging experiments were also conducted for oil-paper insulation with 500-mg/kg DBDS under IEC 62535 corrosion test condition. The corrosion degree of insulation winding was evaluated, and the properties of oil were also discussed. Results showed that the enwinding pattern of the insulating paper on the copper conductor affected the deposition distribution of copper sulfide to be an alternate appearance of a non-corroded crevice and a strip-shaped corrosion deposit on the copper conductor according to the results of field and laboratory. Furthermore, for the insulation winding, the increased number of paper layers on the copper conductor led to the aggravation of sulfur corrosion, prevented the diffusion of copper ions in the oil, and accelerated the formation of acids, which co-affected the properties of the oil. The enwinding of insulating paper on the copper conductor led to the appearance of a tiny crevice on the insulation winding, which is an important occurrence precondition of crevice corrosion. Finally, the mechanism underlying crevice corrosion for insulation winding was theorized as electrochemical corrosion leading to copper sulfide formation.

The ReaxFF molecular dynamics simulation and Monte Carlo method were adopted to analyze the pyrolysis process of cellulose in insulating papers from the perspective of microscopic atom. Molecular dynamics failed to continuously describe the motion behavior of an atom. According to this principle, the system can only calculate the atomic state on the node and then move the atom by a time step to continue calculating the atom. This paper would put forward the optimal step setting method of cellulose thermal decomposition in insulating paper: setting one step every other 0.1 fs. Specifically, for small molecules with a simple structure, such as H2O, the step size was set to 0.4 fs or less, while the step size of macromolecules with complex structures (CH2O2) should be set to 0.2 fs or less. In addition, the relationship between the step size and the temperature to which the system was heated was given as well in this paper. In previous literatures, empirical values were used to set the step size. This study would not only provide a theoretical basis for the study on the bond formation and fracture process of cellulose pyrolysis products, but also offer the data and guidance for related fields in the future, thus rendering an efficient simulation process.

The condition of a power transformer can be predicted based on the contents of the transformer oil. One of the most common parameters that are observed in the transformer oil is 2-Furaldehyde, a compound that is produced due to the aging of Kraft paper. Although the optical characterization of 2-Furaldehyde has been widely reported, the fundamental theories of the observation of the optical absorbance peaks have not been elaborated. This study investigates the optical characteristics of 2-Furaldehyde in the near infrared region. Ten samples with different concentrations of 2-Furaldehyde were prepared and verified using the conventional method. The samples were then characterized using optical spectroscopy method with 50 mm path length cuvettes. Three peaks were observed at 1610 nm – 1640 nm, 1100 nm – 1115 nm and 860 nm – 890 nm wavebands and were correlated to the overtones of the aromatic C-H stretch in 2-Furaldehyde. The appearance of these overtones corresponding to the Morse Oscillation Theory was discussed. This fundamental knowledge is significant in developing a portable optical device that enables the detection of 2-Furaldehyde on site.

Frequency domain spectroscopy (FDS) technique is widely applied in the condition assessment of the oil-paper system in power transformers. However, the synergistic effect generated by moisture and temperature on the FDS data cannot be analyzed by the existing model since the single independent variable (moisture or temperature) is considered in the construction of the model. To quantify such the synergistic effect, a novel method that utilized for normalizing (or standardizing) the FDS curve is reported based on the theory of the power series and fitting analysis. The present findings reveal that the reported method is capable of predicting the dielectric loss (tan $\delta$ ) curve under diverse test conditions, in which the average error is less than 7%. The synergistic effect can be also explored by using the extracted feature parameters. The potential application is then proved to make up for the measurement errors during the FDS test, the findings are expected to promote the moisture analysis of the transformer insulation.

In this short paper, our main objective is to construct binary locally repairable codes (LRCs) with good properties. Two constructions of LRCs with short lengthes are proposed. The first one is that define a u-linearly independent set (u-LIS) of an LRC with disjoint repair groups (DRGs) and enlarge it into another one with bigger size to construct new LRCs. The second is puncturing check matrices of known codes to construct new LRCs. As an application, many new binary LRCs are constructed from distance optimal linear codes, which are also locality optimal according to the Cadambe-Mazumdar (C-M) bound.