Search

In the European Union, increasing attention is already being paid not only to the development of renewable energy sources, but also to the establishment of solutions to achieve local energy self-sufficiency while increasing the role of citizens in managing the energy they generate. This approach is expected both to have a positive impact on the environment and the reduction of greenhouse gas emissions, and to enhance energy security—both in economic and civic terms by, i.a., combating energy poverty. The development of local energy communities promoted in the EU is supported i.a. by energy cooperatives. These contribute to the efficient harnessing of renewable energy potential in rural and urban-rural areas, and have been developing in Poland for several years now. In their previous studies, the authors of this research paper attempted to verify the generation (number, type and capacity of installed sources) and consumption (energy demand) configurations in which an energy cooperative would be a viable solution for prosumers who might establish it. However, over the past few years, the conditions for prosumers and the method of their accounting with the electricity seller have changed radically in Poland (shift from net metering to net billing). This situation has opened up space for further research and encouraged the authors to revisit the problem of analyzing the viability of establishing energy cooperatives in relation to the rules of operation of individual prosumers. This research was carried out for three scenarios, and the horizon of the analyses conducted and described extends to 2045. The comparative analysis included energy consumers without their own generation sources, prosumers with a photovoltaic generation installation covered by the net billing model, as well as a scenario involving prosumers' cooperation within an energy cooperative, which by law is settled in the net metering model. Conclusions from the research and simulations made it possible to confirm the claim that, despite changes in the rules of prosumer billing, developing energy independence in the energy community formula results in a significant reduction in the cost of purchasing electricity (even several times lower purchase costs in the timeframe analyzed) and can lead to a reduction in the payback time of investments in generation sources even by a factor of two. The results presented in this research paper open up space for further research. The outcomes allow us to assume that energy cooperatives—in the organizational and institutional model in Poland—are a good tool for reducing the phenomenon of energy poverty on a local scale. [ABSTRACT FROM AUTHOR]

With the rapid development of the information age, smart meters play an important role in the smart grid. However, there are more and more attacks on smart meters, which mainly focus on the identity authentication of smart meters and the security protection of electricity consumption data. In this paper, an efficient lightweight smart meter authentication scheme is proposed based on the Chinese Remainder Theorem (CRT), which can realize the revocation of a single smart meter user by publishing a secret random value bound to the smart meter identity. The proposed scheme not only protects the security of smart meter electricity consumption data by using encryption, but also resists identity attacks from both internal and external adversaries by using hash functions and timestamps. Experiment shows that the proposed scheme has lower computation overhead and communication overhead than other authentication schemes and is more suitable for smart meter authentication. [ABSTRACT FROM AUTHOR]

Energy efficiency is an important issue in industry, especially with the ever-increasing consumption of electrical energy. The power quality and the traceability of metering devices are essential when integrating energy metering systems for energy efficiency. This management requires an understanding of electrical current events such as pulse and transient currents. Current transducers are widely used to measure these electrical current events up to a few megahertz. Their use makes it possible to measure not only the main current flowing through the transducer, but also the bypass current that affects electrical equipment. Calibration of these sensors up to a few megahertz then becomes an essential step. Currently, most calibration methods are limited to 100 kHz frequency for a current of 10 A. This paper presents an improvement of a traceable calibration methodology for current transducers up to 10 A and 1 MHz, thus increasing, by 10 times, the current level for such high frequency applications. This calibration methodology is based on a metrological traceability chain (uninterrupted link to the International System of Units) with respect to a calculable current shunt and is currently the only traceable method for calibrating current transducers at 10 A and up to 1 MHz. The uncertainty obtained for the transimpedance ratio is less than 0.2%, which is considerably reduced with respect to the existing capabilities. [ABSTRACT FROM AUTHOR]

Metrological characterisation of static energy meters under realistic low power quality conditions is a basic requirement for proper grid control and fair energy billing. The paper reports about a new proposed methodology, where the meters are tested under conditions directly recorded at installation sites. The waveforms of voltages and currents are sampled using a portable instrument; they are reproduced in laboratory conditions with a phantom power generator, with a bandwidth covering up to the 40th harmonic. The recording site is a photovoltaic energy production facility, having a a nominal power of 50 kW, at the coupling section to the grid. These waveforms were then reproduced in the laboratory, and tested on different models of single- and three-phase commercial static energy meters; the models chosen represent both energy meters used by energy providers at the point of common-coupling, and also meters typically used for in-line monitoring by end users. The quantity of interest is the reading error of the measured energy, when tested with the conditions reproduced from the on-field measurements, in comparison with a reference meter. All tested energy meter models comply with the present international documentary standards, which require tests under low power quality conditions; nevertheless, there are models that show unacceptable errors (up to 25%) in the measurement of active energy when tested with the on-field recorded waveforms. This suggests that the standardised testing waveforms might, in some cases, be not fully representative of the actual conditions encountered in the field. [ABSTRACT FROM AUTHOR]