Search

This paper presents a novel method for generating and shaping reverse energy flow through the interference of light fields from a minimal number of point light sources. Until now, reverse energy flow has only been observed using complex light fields, such as optical vortices or cylindrical vector beams, limiting the formation of reverse energy flow near the optical axis. We demonstrate both analytically and numerically that unbounded regions of reverse energy flow can be achieved with just two point light sources, positioned asymmetrically at specific angles (e.g., 90 or 45 degrees) and with particular polarization states. The results indicate that the relative reverse energy flow can be enhanced by increasing the number of sources to three or four, adjusting their polarization, or introducing a vortex phase singularity. The presence of an initially embedded asymmetry in the fields under consideration leads to the formation of a non-uniform distribution of spin and orbital angular momentum density. Variations in the polarization state, as well as the introduction of a vortex phase singularity, allow for changing the distribution of angular momentum density while maintaining the presence of a reverse energy flow. We also explore the feasibility of implementing the obtained results using sectional phase diffractive optical elements, which will enhance the energy efficiency of the generated fields compared to point sources. [ABSTRACT FROM AUTHOR]

Interference of two and four light beams with linear or circular polarization is studied analytically and numerically based on the Richards–Wolf formalism. We consider such characteristics of the interference fields as the distribution of intensity, polarization, and spin angular momentum density. The generation of light fields with 1D and 2D periodic structure of both intensity and polarization is demonstrated. We can control the periodic structure both by changing the polarization state of the interfering beams and by changing the numerical aperture of focusing. We consider examples with a basic configuration, as well as those with a certain symmetry in the polarization state of the interfering beams. In some cases, increasing the numerical aperture of the focusing system significantly affects the generated distributions of both intensity and polarization. Experimental results, obtained using a polarization video camera, are in good agreement with the simulation results. The considered light fields can be used in laser processing of thin films of photosensitive (as well as polarization-sensitive) materials in order to create arrays of various ordered nano- and microstructures. [ABSTRACT FROM AUTHOR]

Photosensitive materials are widely used for the direct fabrication of surface relief gratings (SRGs) without the selective etching of the material. It is known that the interferometric approach makes it possible to fabricate SRGs with submicron and even subwavelength periods. However, to change the period of the written SRGs, it is necessary to change the convergence angle, shift a sample, and readjust the interferometric setup. Recently, it was shown that structured laser beams with predetermined, periodically modulated polarization distributions can also be used to fabricate SRGs. A structured laser beam with the desired polarization distribution can be formed with just one polarizing optical element—for example, the so-called depolarizer, a patterned micro-retarder array. The use of such stacked elements makes it possible to directly control the modulation period of the polarization of the generated laser beam. We show that this approach allows one to fabricate SRGs with submicron periods. Moreover, the addition of q-plates, elements effectively used to generate cylindrical vector beams with polarization singularities, allows the efficient formation of fork polarization gratings (FPGs) and the fabrication of higher-order fork-shaped SRGs. Full control of the parameters of the generated FPGs is possible. We demonstrate the formation of FPGs of higher orders (up to 12) by only adding first- and second-order q-plates and half-wave plates to the depolarizers. In this work, we numerically and experimentally study the parameters of various types of SRGs formed using these stacked polarizing elements and show the significant potential of this method for the laser processing of photosensitive materials, which often also serve as polarization sensors. [ABSTRACT FROM AUTHOR]

We propose a method for generating three-dimensional light fields with given intensity and phase distributions using purely phase transmission functions. The method is based on a generalization of the well-known approach to the design of diffractive optical elements that focus an incident laser beam into an array of light spots in space. To calculate purely phase transmission functions, we use amplitude encoding, which made it possible to implement the designed elements using a single spatial light modulator. The generation of light beams in the form of rings, spirals, Lissajous figures, and multi-petal "rose" distributions uniformly elongated along the optical axis in the required segment is demonstrated. It is also possible to control the three-dimensional structure of the intensity and phase of the shaped light fields along the propagation axis. The experimentally generated intensity distributions are in good agreement with the numerically obtained results and show high potential for the application of the proposed method in laser manipulation with nano- and microparticles, as well as in laser material processing. [ABSTRACT FROM AUTHOR]

The polarization sensitivity of azopolymers is well known. Therefore, these materials are actively used in many applications of photonics. Recently, the unique possibilities of processing such materials using a structured laser beam were demonstrated, which revealed the key role of the distribution of polarization and the longitudinal component of light in determining the shape of the nano- and microstructures formed on the surfaces of thin azopolymer films. Here, we present numerical and experimental results demonstrating the high polarization sensitivity of thin azopolymer films to the local polarization state of an illuminating structured laser beam consisting of a set of light spots. To form such arrays of spots with a controlled distribution of polarization, different polarization states of laser beams, both homogeneous and locally inhomogeneous, were used. The results obtained show the possibility of implementing a parallel non-uniform patterning of thin azopolymer films depending on the polarization distribution of the illuminating laser beam. We believe that the demonstrated results will not only make it possible to implement the simultaneous detection of local polarization states of complex-shaped light fields but will also be used for the high-performance fabrication of diffractive optical elements and metasurfaces. [ABSTRACT FROM AUTHOR]