Search

Total hip replacement is one of the most successful orthopedic operations in modern times. Osteolysis of the femur bone results in implant loosening and failure due to improper loading. To reduce induced stress, enhance load transfer, and minimize stress, the use of Ti-6Al-4V alloy in bone implants was investigated. The objective of this study was to perform a three-dimensional finite element analysis (FEA) of the femoral stem to optimize its shape and analyze the developed deformations and stresses under operational loads. In addition, the challenges associated with the manufacturing optimization of the femoral stem using large strain-based finite element modeling were addressed. The numerical findings showed that the optimized femoral stem using Ti-6Al-4V alloy under the normal daily activities of a person presented a strains distribution that promote uniform load transfer from the proximal to the distal area, and provided a mass reduction of 26%. The stress distribution was found to range from 700 to 0.2 MPa in the critical neck area of the implant. The developed computational tool allows for improved customized designs that lower the risk of prosthesis loss due to stress shielding. [ABSTRACT FROM AUTHOR]

The automotive industry continuously enhances vehicle design to meet the growing demand for more efficient vehicles. Computational design and numerical simulation are essential tools for developing concept cars with lower carbon emissions and reduced costs. Underground roads are proposed as an attractive alternative for reducing surface congestion, improving traffic flow, reducing travel times and minimizing noise pollution in urban areas, creating a quieter and more livable environment for residents. In this context, a concept car body design for underground tunnels was proposed, inspired by the mako shark shape due to its exceptional operational kinetic qualities. The proposed biomimetic-based method using computational fluid dynamics for engineering design includes an iterative process and car body optimization in terms of lift and drag performance. A mesh sensitivity and convergence analysis was performed in order to ensure the reliability of numerical results. The unique surface shape of the shark enabled remarkable aerodynamic performance for the concept car, achieving a drag coefficient value of 0.28. The addition of an aerodynamic diffuser improved downforce by reducing 58% of the lift coefficient to a final value of 0.02. Benchmark validation was carried out using reported results from sources available in the literature. The proposed biomimetic design process based on computational fluid modeling reduces the time and resources required to create new concept car models. This approach helps to achieve efficient automotive solutions with low aerodynamic drag for a low-carbon future. [ABSTRACT FROM AUTHOR]

Natural polyphenols found in plants are secondary metabolites and act as natural antioxidants. Phenols prevent lipid oxidation by donating their hydrogen to free radicals generated between reactions of oxygen with unsaturated fatty acids. This work aims to examine turmeric extract for its capacity to act as an antioxidant and pour point depressant additive in biolubricants. The study involved extracting turmeric rhizome and analyzing the extract using the gas chromatography-mass spectrometry (GC-MS) and Fourier-transform infrared spectroscopy (FTIR) techniques to identify phenolic compounds and the nature of bonds in terms of abundance peak areas. The yield of concentrated turmeric rhizome extract by weight was 3.7%. The FTIR analysis revealed O-H band at 3336 cm−1, C-H asymmetric and symmetric stretching at 2940 and 2834 cm−1, C=C cyclic ring at 1680–1515 cm−1. The phenols detected by the GC-MS technique are phenol, 2 -methoxy-3-(2-propenyl) occupying 36.3% area at 16.5 min retention time and Phenol, 2-methoxy-4-(2-propenyl)-, acetate having 3.8% area at 3.8 min retention time. The results show promising capacity of turmeric rhizome extract to act as antioxidant and pour point depressant additive in biolubricants. [ABSTRACT FROM AUTHOR]

Finite element modeling for designing and optimizing lightweight titanium aerospace components requires advanced simulation tools with adequate material modeling. In this sense, a hybrid strategy is proposed in this work to identify the parameters of the Johnson–Cook plasticity and damage laws using a combined direct-inverse method. A direct calibration method for plasticity law is applied based on the literature-reported data of strain-stress curves from experimental tensile tests at different temperatures and strain rates. The triaxiliaty-dependent fracture parameters of the Johnson–Cook damage law at reference conditions of strain rate and temperature (d1, d2, and d3) are calibrated with the direct method based on new data of experimental evolution of computed average fracture strain with the average stress triaxiality. The validation is performed with numerical results from an accurate micromechanics-based Ti64 model. The inverse calibration method is used to determine the strain rate and temperature-dependent damage parameters (d4 and d5) through large strain simulations of uniaxial tensile tests. The numerical results, including average strain and necking profile at fracture, are then utilized to calculate stress triaxiality by the Bridgman criterion for adjusting parameters d4 and d5. The calibrated model yields a 2.1% error for plasticity and 3.4% for fracture predictions. The experimental and simulated load-bearing capacity using the micromechanics damage model differed by only 1%. This demonstrates that the SC11–TNT model of Ti64 is reliable for identifying the Johnson–Cook damage law through the accurate use of inverse methods. The hybrid calibration strategy demonstrates the potential capability of the identified Johnson–Cook model to accurately predict the design load-carrying capacity of Ti64 aerospace components under different deformation rates and temperatures while accounting for material damage effects. [ABSTRACT FROM AUTHOR]

3D-printed thermoplastic parts with continuous fiber reinforcement are known to offer mechanical performance that is highly dependent on design variables and printing parameters. In this work, the role of the reinforcement distribution on the mechanical response of glass fiber-reinforced thermoplastics printed using the fused filament fabrication (FFF) technique is evaluated. Laminates with alternating and continuous reinforcement architecture as well as different fiber orientations such as isotropic (0°, 90°, and 45°) and concentric configurations are characterized from monotonic tensile and flexural loads. The resulting superior macromechanical performance in terms of higher stiffness and strength achieved in samples reinforced with alternating fiber plies is correlated with the micromechanical fractography characteristics and interlaminar shear capacity. [ABSTRACT FROM AUTHOR]