Back to Search
Start Over
Physical vapour deposition of diamond-like carbon coatings on a 7075-T6 substrate for corrosion protection at long and short fatigue lives
- Publication Year :
- 2017
-
Abstract
- Purpose 7075-T6 is the most widespread structural aluminium alloy due to its high mechanical strength. However, use of this alloy in critical aeronautic, maritime, and automotive sectors is limited by the susceptibility of T6 treatment to cracking and pitting corrosion. To improve fatigue behaviour in aggressive environments, several authors have proposed the use of different coatings to protect the substrate. Studies have investigated the application of thin hard coatings on light alloys by physical vapour deposition (PVD). Different contributions of residual stresses, thermal modification of the substrate, and mechanical interaction between the coating and aluminium substrate were investigated. The purpose of this paper is to investigate the rotating bending fatigue behaviour (R=−1) of 7075-T6 PVD diamond-like carbon (DLC)-coated specimens in air and in a corrosive environment. Tests were conducted at different applied stresses. Scanning electron micrographs of the fracture surface are provided to investigate the influences of mechanical and environmental driving forces on the failure mechanism. Design/methodology/approach The paper conducted an experimental study of the fatigue resistance of DLC coatings on a 7075-T6 substrate for corrosion protection at long and short fatigue lives, which includes rotating bending fatigue tests, step-loading fatigue test procedure, tests in aggressive environment (methanol), tests at high and low fatigue lives, analysis of the fracture surface, and analysis of the driving forces. Findings Tests performed in air showed that the coating anticipates crack nucleation for high applied loads, whereas for lower loads, the difference among fatigue curves decreases. This result is very interesting from an industrial standpoint because the obtained material shows improved corrosion and wear resistance, without the fatigue resistance loss generally associated with hard coatings. The methanol environment accelerates crack nucleation and propagation, resulting in a sensible deterioration of the fatigue behaviour. A minimum soaking time seems to be necessary before the damaging effect of the environment begins. The coating has a certain protective effect against the environment, but this protection is insufficient for the specimen to achieve fatigue limits beyond those of the uncoated specimens. This deficiency can be related to small pores or defects in the coating, which allow contact between the substrate and the environment. Further tests are necessary to verify whether there exists a load under which the fatigue behaviour of the coated specimens is better than that of the uncoated specimens. Crack nucleation due to fatigue occurs close to the outer surface for all observed samples. For coated samples tested at the lowest stress level, crack nucleation seems to be located below the surface. This observation means that premature coating cracking, which characterises the nucleation mechanism at higher loads, did not occur at lower stress levels. The fracture surface of uncoated samples was clearly damaged by the aggressive solution, justifying the poor fatigue resistance. Research limitations/implications The obtained data do not represent actual S-N curves, which would necessitate a larger number of tests with proper statistics. Nevertheless, some indications of the DLC effects on 7075-T6 specimens in air and methanol environments can be deduced. The step-loading technique seems to be critical for tests in corrosive environments, probably because the total soaking time in the corrosive environment is generally higher than it is for the single-run test. Originality/value The originality of the paper lies in the application of the step-loading test procedure to quickly detect the mechanical and chemical driving forces that control the damage and structural integrity of light alloys components in very aggressive environments.
- Subjects :
- Materials science
Nucleation
chemistry.chemical_element
02 engineering and technology
engineering.material
Thin hard coating
Corrosion
0203 mechanical engineering
Coating
Residual stress
Aluminium
Pitting corrosion
Aluminium alloy
Composite material
Fatigue
7075-T6
Civil and Structural Engineering
Mechanical Engineering
Methanol
Metallurgy
Step-loading
021001 nanoscience & nanotechnology
Fatigue limit
Settore ING-IND/14 - Progettazione Meccanica e Costruzione di Macchine
020303 mechanical engineering & transports
chemistry
Mechanics of Materials
visual_art
engineering
visual_art.visual_art_medium
0210 nano-technology
Subjects
Details
- Language :
- English
- Database :
- OpenAIRE
- Accession number :
- edsair.doi.dedup.....d62924b344d95409b22cc1e6876b8da1