Distribution of Water in Soil under Drip Irrigation by Moment Analysis using Different Discharges.

Background and Objectives Water shortage and the need for its optimal use in arid and semi-arid regions, including Iran, has led water officials and farmers to use modern irrigation systems, such as drip irrigation with the aim of making optimal use of water resources. Drip irrigation has been welcomed in most parts of the world due to its high efficiency and the possibility of irrigation in different environmental conditions. The most important reason for the superiority of drip irrigation over other irrigation methods is the controllable amount of water for each plant. Drip irrigation is a method in which water is poured out of the net at low pressure through an orifice or device called an emitter and dripped into the bottom of the plant. This irrigation system, like other methods, requires accurate knowledge of the parameters affecting it to achieve the desired efficiency. One of the most important parameters for the irrigation system is the distribution of moisture in the soil and in fact the shape of the moist bulb. Therefore, knowledge of how to distribute water in the soil is essential for the proper design and management of subsurface drip irrigation systems. Since testing is very difficult and time consuming to detect the shape of moisture distribution in the soil, the use of numerical and analytical simulation can be an effective and efficient way to design these systems. Methodology In order to determine the progress of the moisture front in drip irrigation, first the soil texture type and physical properties of the soil were determined. It should be noted that the emitter flow rate was measured and adjusted in volume at the beginning of the test to minimize the difference between the emitter flows along the three side tubes. Evaluation experiments were performed with three outflows of 2, 4 and 6 liters per hour. With the start of the system, the progress of the moisture front at different times was measured by digging a trench using a scale. Numerical simulation of moisture front progress was performed using HYDRUS model based on Richard equation and analytical simulation was performed using Moment Analysis. HYDRUS software was used to numerically simulate the progress of the moisture front. The simulation range was considered to be 100 cm by 100 cm on the two-dimensional plane. In these simulations, 3956 nodes are used to represent the entire simulation range and also, relevant equations were used to calculate the two-dimensional spatial Moment of the wetting pattern . Findings The simulations show that the initial volumetric moisture content is 0.11 and the saturation volumetric moisture content is 0.380 and the water dispersion rate increases over time on the x and z axes. With increasing flow, the maximum dispersion is in the x-axis, which occurs in flow of 6 liters per hour. The result for flow of 6 liters per hour based on the data used is slightly higher than the desired value. The reason why the value of M00 in the flow rate of 6 liters per hour is higher than expected, is that in the simulation flow rate of 6 liters per hour change in the size of the inlet diameter and the amount of flux changes the amount of water entering the soil and moistens a large volume of soil. Due to the different amount of moisture applied to the area at different times, the value of 𝑧𝑐, 𝜎𝑥 2, 𝜎𝑧 2 is different and has caused a change in the size of the oval in different flows. The increase in the size of the ovals indicates the high dispersion of water in that area. The results showed that the Moment analysis was able to express the position of the center of mass of water distributed in the soil with correlation coefficient of 0.986 in linear mode and 0.982 in logarithmic mode. By comparing the values of diameter and depth obtained from the HYDRUS and the drawn ovals, it can be concluded that both methods provide close results. The accuracy of the Moment analysis method in simulating different types of moisture patterns resulting from drip irrigation under different flows with the use of different volumes of water is similar to the HYDRUS model and therefore it is possible to use this feature to predict the pattern of moisture from a certain flow using a specific volume of water . Conclusion In this study, the accuracy of Moment analysis in simulating various moisture patterns resulting from drip irrigation under different flows with the use of different volumes of water was investigated and the possibility of using this feature to predict the pattern of moisture from a given flow using a specific volume of water checked. In order to investigate the Moment of the amount of water distributed in the soil by subsurface drip irrigation, simulation was performed by two-dimensional HYDRUS software for three discharges of 2, 4 and 6 liters per hour with an inlet water volume of 12 liters. Then, using the results of simulation of moisture distribution range by a programming language including MATLAB software, and by calculating the Moments, it was determined that the Moments are able to express the position of the center of mass of water distributed in the soil and how it is distributed relative to x and z axes. The increase in the size of the ovals indicates that more water is distributed in that area. Comparing the diameters and depths of the moisture front between the simulated HYDRUS model and the Moment analysis model, it was found that the Moment analysis is an efficient way to study the distribution of water moisture by drip irrigation and this method can be used as an alternative input to estimate parameters. [ABSTRACT FROM AUTHOR]