ارزیابی مدیریتهای مختلف آبیاری بهمنظور هوشمندسازی سامانه آبیاری بارانی.

In Iran, pressurized irrigation systems cover a large area of agricultural land, but water use efficiency remains low because farmers tend to do deficit (over) - irrigation due to their lack of knowledge on crop water requirements. To address this issue, irrigation systems can be automated, and it is important to estimate crop water requirements accurately. This can be done based on soil moisture deficit or meteorological data. The water required can then be applied using a volume meter or by determining irrigation time based on sprinkler flow rate. The study aimed to compare crop water requirement estimates based on soil moisture deficit and meteorological data, as well as the amount of water applied using volume and time-based methods. Methodology The study was conducted in the research farm of Razi University, Kermanshah, Iran, on a sprinkler irrigation system equipped with pressure and flow measuring devices, pressure switches, and electrical valves. The field was under corn cultivation, and four types of irrigation management were evaluated, which included a combination of two methods of determining crop water requirement (soil moisture deficiency and meteorological data) and two methods of irrigation application (time or volume). The four treatments were soil moisture - time (MT), soil moisture - volume (MV), weather - time (WT), and weather - volume (WV). The crop water requirement was calculated using the Penman Monteith formula based on daily weather data. Soil moisture was measured at different depths one day before irrigation, and the soil moisture deficit was calculated to determine the crop water requirement based on soil moisture. The irrigation volume for each sprinkler in the irrigation cycle was calculated using equations 1 and 2. V= ∑_i=1ⁿ ETc_i* s_m*s_i/e_a Method 1: Based on meteorological data (2) V = d*s_m*s_i/e_a Method 2: Based on soil moisture deficiency where V is the irrigation volume, d is the water deficit depth in the root zone, n is the number of days after the previous irrigation, and Sm and Sl are the distance between the laterals and sprinklers respectively (21 m * 21m), and e_a is the irrigation application efficiency (0.8). In the volumetric-based method (treatments WV and MV), the volume of water applied was measured using a water meter with a precision of 0.1 liters, and irrigation was stopped after passing the required volume of water. In the time-based method (treatments WT and MT), the irrigation time was calculated by dividing the irrigation volume by the average flow rate of the sprinklers (3 liters per second), and irrigation was stopped after the calculated duration. The actual sprinkler flow rate was calculated based on the volume of applied water and irrigation time in each treatment and irrigation round. Crop yield was measured at the time of harvest in the studied treatments and a control treatment managed by the Faculty of Agriculture. The irrigation treatments were not applied in the first month of the growth period due to field limitations. Results and discussion The results show that the crop water requirement calculated based on meteorological data at the beginning and end of the growing period was more than the method based on soil moisture. In total, the amount of crop water requirement calculated based on soil moisture was 8% more than meteorological based method. The volume of applied water in treatments of MT and WT was 14 and 8% more than in MV and WV treatments, respectively. The actual flow rate of sprinklers was different from the design flow rate due to irrigation situations in other parts of the farm. The average discharge of sprinklers (12 irrigation events) in WT, MT, WV, and MV treatments was 2.79, 3.03, 3.27, and 3.12 l/s, respectively. The irrigation time in volume and time-based methods also showed a significant difference. The irrigation time in MT and MV treatments was 10 and 18% longer than in WT and WV treatments, respectively. The final grain yield, applied water, and crop water productivity (based on the treatment application period) are presented in Conclusions The study found that due to the non-uniformity of sprinkler discharge, applying irrigation by volume method is better than the time-based method. The results suggest that the MV treatment, which determined the amount of irrigation based on soil moisture deficit and applied it using a volumetric method, is a suitable option for automating sprinkler irrigation systems in the studied region. [ABSTRACT FROM AUTHOR]