Search

The goal of this study was to develop an image analysis algorithm for quantifying the effects of remodelling on cortical bone during early fracture healing. An adaptive thresholding technique with boundary curvature and tortuosity control was developed to automatically identify the endocortical and pericortical boundaries in the presence of high-gradient bone mineral density (BMD) near the healing zone. The algorithm successfully detected boundaries in more than 47,000 microCT images from 12 pairs of healing ovine osteotomies and intact contralateral tibiae. Resampling techniques were used to achieve data dimensionality reduction on the segmented images, allowing characterisation of radial, circumferential, and axial distributions of cortical BMD. Local (transverse slice) and total (whole bone) remodelling scores were produced. These surrogate measures of cortical remodelling derived from BMD revealed that cortical changes were detectable throughout the region covered by callus and that the localised loss of cortical BMD was highest near the osteotomy. Total remodelling score was moderately and significantly correlated with callus volume and mineral composition (r > 0.64, p

Abstract Background Gray horses are predisposed to equine malignant melanoma (EMM) with advancing age. Depending on the tumor’s location and size, they can cause severe problems (e.g., defaecation, urination, feeding). A feasible therapy for EMM has not yet been established and surgical excision can be difficult depending on the location of the melanoma. Thus, an effective and safe therapy is needed. Naturally occurring betulinic acid (BA), a pentacyclic triterpene and its synthetic derivate, NVX-207 (3-acetyl-betulinic acid-2-amino-3-hydroxy-2-hydroxymethyl-propanoate) are known for their cytotoxic properties against melanomas and other tumors and have already shown good safety and tolerability in vivo. In this study, BA and NVX-207 were tested for their permeation potential into equine skin in vitro in Franz-type diffusion cell (FDC) experiments after incubation of 5 min, 30 min and 24 h, aiming to use these formulations for prospective in vivo studies as a treatment for early melanoma stages. Potent permeation was defined as reaching or exceeding the half maximal inhibitory concentrations (IC50) of BA or NVX-207 for equine melanoma cells in equine skin samples. The active ingredients were either dissolved in a microemulsion (ME) or in a microemulsion gel (MEG). All of the formulations were transdermally applied but the oil-in-water microemulsion was administered with a novel oxygen flow-assisted (OFA) applicator (DERMADROP TDA). Results All tested formulations exceeded the IC50 values for equine melanoma cells for BA and NVX-207 in equine skin samples, independently of the incubation time NVX-207 applied with the OFA applicator showed a significant time-dependent accumulation and depot-effect in the skin after 30 min and 24 h (P

This study was designed as proof of principle and safety test of the novel technique, the Immediate Stabilization System (ISS). The technique is designed to immediately stabilize polymer-augmented pedicle screws (PAS) in deficient bone and avoid complications of loosening pedicle screws at the bone-screw interface, especially in osteoporotic patients. A polymer sleeve was designed as augmentation to improve screw anchorage after drilling the screw hole. By applying ultrasonic energy, the polymeric tube was molded into the pores of the host bone forming a strong and uniform bond with the adjacent bone. The original screw was then implanted into the denser bony environment leading to an enhanced immediate stability. The ISS-treated implants were compared to conventionally placed pedicle screws in ex-vivo cadaver bones (2 sheep spines, n = 6 implants per spine, total 12 screws) and in-vivo in a spinal sheep model (Swiss alpine sheep, n = 5, 4 implants per animal, total 20 screws). The primary stability of ISS-treated pedicle screws was increased in ex-vivo bone (+24% insertion torque (IT)) and in-vivo (+32.9% IT) in sheep spine. Removal torque (RT) was lower in the in PAS tested for 8 weeks in-vivo. The ISS technology demonstrated improved anchorage of pedicle screws in ex-vivo cadaver bones as well as in-vivo studies in sheep spine.

ObjectiveThe objective of this study was to retrospectively assess the effect of Radiofrequency Volumetric Tissue Reduction (RFVTR) on hypertrophic turbinates and clinical outcome in brachycephalic dogs when included in multi-level surgery (MLS).Study designClinical retrospective multicenter study.Animals132 client-owned brachycephalic dogs.Methods132 brachycephalic dogs with high-grade Brachycephalic Obstructive Airway Ayndrome (BOAS) and hypertrophic turbinates were treated with RFVTR as part of MLS of the upper airways. Intranasal obstruction was evaluated by computer tomography (CT) and antero-/retrograde rhinoscopy before and 6 months after RFVTR. The clinical records, the CT images and the rhinoscopy videos were reviewed and clinical evolution was evaluated using a standardized questionnaire. The data was scored semi-quantitatively.ResultsIn this study, 132 patients were included for a follow-up period of 120 weeks. RFVTR resulted in minor complications, including serous nasal discharge within the first postoperative week in all dogs, and intermittent nasal congestion between 3-8 weeks after treatment in 24.3% of the patients. Rhinoscopy and CT follow-ups were available for 33 patients. Six months after treatment intranasal airspace was increased (p = 0.002) and the presence and overall amount of mucosal contact points was reduced (p = 0.039).ConclusionMLS with RFVTR led to a significant reduction in turbinate volume at the 6-month follow-up examination and significant clinical improvement over a long-term period of 120 weeks. This suggests the viability of RFVTR as a turbinate-preserving treatment for intranasal obstruction in dogs with BOAS.Clinical significanceRFVTR is a minimally invasive turbinoplasty technique for intranasal obstruction in dogs with BOAS and can be included in MLS without increasing complication rates.

To date, several types of airway stents are available to treat central airway obstructions. However, the ideal stent that can overcome anatomical, mechanical and microbiological issues is still awaited. In addition, therapeutic effect and self-elimination of these stents are desirable properties, which pose an additional challenge for development and manufacturing. We aimed to create a prototype bioresorbable tracheal stent with acceptable clinical tolerance, fit and biocompatibility, that could be tested in a rabbit model and in the future be further optimized to enable drug-elution and ensure local therapeutic effect. Twenty-one New Zealand White Rabbits received five different types of bioresorbable tracheal stents, 3D-printed from poly(D,L-lactide-co-ε-caprolactone) metacrylates. Various configurations were tested for their functionality and improved until the best performing prototype could undergo detailed in vivo assessment, regarding clinical tolerance, migration and biocompatibility. Previously tested types of 3D printed stents in our preliminary study required improvement due to several problems, mainly related to breakage, unreliable stability and/or migration within the trachea. Abandoned or refined pre-prototypes were not analyzed in a comparative way. The final best performing prototype stent (GSP2 (Group Stent Prototype 2), n = 8) allowed a transoral application mode and showed good clinical tolerance, minimal migration and acceptable biocompatibility. The good performance of stent type GSP2 was attributed to the helix-shaped surface structure, which was therefore regarded as a key-feature. This prototype stent offers the possibility for further research in a large animal model to confirm the promising data and assess other properties such as bioresorption.

Abstract Background Therapies using electromagnetic field technology show evidence of enhanced bone regeneration at the fracture site, potentially preventing delayed or nonunions. Methods Combined electric and magnetic field (CEMF) treatment was evaluated in two standardized sheep tibia osteotomy models: a 3-mm non-critical size gap model and a 17-mm critical size defect model augmented with autologous bone grafts, both stabilized with locking compression plates. CEMF treatment was delivered across the fracture gap twice daily for 90 min, starting 4 days postoperatively (post-OP) until sacrifice (9 or 12 weeks post-OP, respectively). Control groups received no CEMF treatment. Bone healing was evaluated radiographically, morphometrically (micro-CT), biomechanically and histologically. Results In the 3-mm gap model, the CEMF group (n = 6) exhibited higher callus mineral density compared to the Control group (n = 6), two-fold higher biomechanical torsional rigidity and a histologically more advanced callus maturity (no statistically significant differences). In the 17-mm graft model, differences between the Control (n = 6) and CEMF group (n = 6) were more pronounced. The CEMF group showed a radiologically more advanced callus, a higher callus volume (p = 0.003) and a 2.6 × higher biomechanical torsional rigidity (p = 0.024), combined with a histologically more advanced callus maturity and healing. Conclusions This study showed that CEMF therapy notably enhanced bone healing resulting in better new bone structure, callus morphology and superior biomechanical properties. This technology could transform a standard inert orthopedic implant into an active device stimulating bone tissue for accelerated healing and regeneration.

Structural muscle changes, including muscle atrophy and fatty infiltration, follow rotator cuff tendon tear and are associated with a high repair failure rate. Despite extensive research efforts, no pharmacological therapy is available to successfully prevent both muscle atrophy and fatty infiltration after tenotomy of tendomuscular unit without surgical repair. Poly(ADP-ribose) polymerases (PARPs) are identified as a key transcription factors involved in the maintenance of cellular homeostasis. PARP inhibitors have been shown to influence muscle degeneration, including mitochondrial hemostasis, oxidative stress, inflammation and metabolic activity, and reduced degenerative changes in a knockout mouse model. Tenotomized infraspinatus were assessed for muscle degeneration for 16 weeks using a Swiss Alpine sheep model (n = 6). All sheep received daily oral administration of 0.5 mg Talazoparib. Due to animal ethics, the treatment group was compared with three different controls from prior studies of our institution. To mitigate potential batch heterogeneity, PARP-I was evaluated in comparison with three distinct control groups (n = 6 per control group) using the same protocol without treatment. The control sheep were treated with an identical study protocol without Talazoparib treatment. Muscle atrophy and fatty infiltration were evaluated at 0, 6 and 16 weeks post-tenotomy using DIXON-MRI. The controls and PARP-I showed a significant (control p < 0.001, PARP-I p = 0.01) decrease in muscle volume after 6 weeks. However, significantly less (p = 0.01) atrophy was observed in PARP-I after 6 weeks (control 1: 76.6 ± 8.7%; control 2: 80.3 ± 9.3%, control 3: 73.8 ± 6.7% vs. PARP-I: 90.8 ± 5.1% of the original volume) and 16 weeks (control 1: 75.7 ± 9.9; control 2: 74.2 ± 5.6%; control 3: 75.3 ± 7.4% vs. PARP-I 93.3 ± 10.6% of the original volume). All experimental groups exhibited a statistically significant (p < 0.001) augmentation in fatty infiltration following a 16-week period when compared to the initial timepoint. However, the PARP-I showed significantly less fatty infiltration (p < 0.003) compared to all controls (control 1: 55.6 ± 6.7%, control 2: 53.4 ± 9.4%, control 3: 52.0 ± 12.8% vs. PARP-I: 33.5 ± 8.4%). Finally, a significantly (p < 0.04) higher proportion and size of fast myosin heavy chain-II fiber type was observed in the treatment group. This study shows that PARP-inhibition with Talazoparib inhibits the progression of both muscle atrophy and fatty infiltration over 16 weeks in retracted sheep musculotendinous units.

The goal of this study was to develop an image analysis algorithm for quantifying the effects of remodelling on cortical bone during early fracture healing. An adaptive thresholding technique with boundary curvature and tortuosity control was developed to automatically identify the endocortical and pericortical boundaries in the presence of high-gradient bone mineral density (BMD) near the healing zone. The algorithm successfully detected boundaries in more than 47,000 microCT images from 12 pairs of healing ovine osteotomies and intact contralateral tibiae. Resampling techniques were used to achieve data dimensionality reduction on the segmented images, allowing characterisation of radial, circumferential, and axial distributions of cortical BMD. Local (transverse slice) and total (whole bone) remodelling scores were produced. These surrogate measures of cortical remodelling derived from BMD revealed that cortical changes were detectable throughout the region covered by callus and that the localised loss of cortical BMD was highest near the osteotomy. Total remodelling score was moderately and significantly correlated with callus volume and mineral composition (r > 0.64, p < 0.05), suggesting that the cortex may be a source of mineral needed to build callus. [ABSTRACT FROM AUTHOR]

Abstract Bone fractures commonly repair by forming a bridging structure called callus, which begins as soft tissue and gradually ossifies to restore rigidity to the bone. Virtual mechanical testing is a promising technique for image-based assessment of structural bone healing in both preclinical and clinical settings, but its accuracy depends on the validity of the material model used to assign tissue mechanical properties. The goal of this study was to develop a constitutive model for callus that captures the heterogeneity and biomechanical duality of the callus, which contains both soft tissue and woven bone. To achieve this, a large-scale optimization analysis was performed on 2363 variations of 3D finite element models derived from computed tomography (CT) scans of 33 osteotomized sheep under normal and delayed healing conditions. A piecewise material model was identified that produced high absolute agreement between virtual and physical tests by differentiating between soft and hard callus based on radiodensity. The results showed that the structural integrity of a healing long bone is conferred by an internal architecture of mineralized hard callus that is supported by interstitial soft tissue. These findings suggest that with appropriate material modeling, virtual mechanical testing is a reliable surrogate for physical biomechanical testing.

Objective: The objective of this study was to retrospectively assess the effect of Radiofrequency Volumetric Tissue Reduction (RFVTR) on hypertrophic turbinates and clinical outcome in brachycephalic dogs when included in multi-level surgery (MLS). Study design: Clinical retrospective multicenter study. Animals: 132 client-owned brachycephalic dogs. Methods: 132 brachycephalic dogs with high-grade Brachycephalic Obstructive Airway Ayndrome (BOAS) and hypertrophic turbinates were treated with RFVTR as part of MLS of the upper airways. Intranasal obstruction was evaluated by computer tomography (CT) and antero-/retrograde rhinoscopy before and 6 months after RFVTR. The clinical records, the CT images and the rhinoscopy videos were reviewed and clinical evolution was evaluated using a standardized questionnaire. The data was scored semi-quantitatively. Results: In this study, 132 patients were included for a follow-up period of 120 weeks. RFVTR resulted in minor complications, including serous nasal discharge within the first postoperative week in all dogs, and intermittent nasal congestion between 3–8 weeks after treatment in 24.3% of the patients. Rhinoscopy and CT follow-ups were available for 33 patients. Six months after treatment intranasal airspace was increased (p = 0.002) and the presence and overall amount of mucosal contact points was reduced (p = 0.039). Conclusion: MLS with RFVTR led to a significant reduction in turbinate volume at the 6-month follow-up examination and significant clinical improvement over a long-term period of 120 weeks. This suggests the viability of RFVTR as a turbinate-preserving treatment for intranasal obstruction in dogs with BOAS. Clinical significance: RFVTR is a minimally invasive turbinoplasty technique for intranasal obstruction in dogs with BOAS and can be included in MLS without increasing complication rates. [ABSTRACT FROM AUTHOR]

Abstract Background A new locking screw technology, named variable fixation, has been developed aiming at promoting bone callus formation providing initial rigid fixation followed by progressive fracture gap dynamisation. In this study, we compared bone callus formation in osteotomies stabilized with standard locking fixation against that of osteotomies stabilized with variable fixation in an established tibia ovine model. Methods A 3 mm tibial transverse osteotomy gap was stabilized in three groups of six female sheep each with a locking plate and either 1) standard fixation in both segments (group LS) or 2) variable fixation in the proximal and standard fixation in the distal bone segment (group VFLS3) or 3) variable fixation in both segments (group VFLS6). The implantation site and fracture healing were compared between groups by means of radiologic, micro tomographic, biomechanical, and histological investigations. Results Compared to LS callus, VFLS3 callus was 40% larger and about 3% denser, while VFLS6 callus was 93% larger and its density about 7.2% lower. VFLS3 showed 65% and VFLS6 163% larger amount of callus at the cis-cortex. There wasn’t a significant difference in the amount of callus at the cis and trans-cortex in groups featuring variable fixation only. Investigated biomechanical variables were not significantly different among groups and histology showed comparable good healing in all groups. Tissues adjacent to the implants did not show any alteration of the normal structure in all groups. Conclusions Variable fixation promoted the formation of a larger amount of bone callus, equally distributed at the cis and trans cortices. The histological and biomechanical properties of the variable fixation callus were equivalent to those of the standard fixation callus. The magnitude of variable fixation had a biological effect on the formation of bone callus. At the implantation site, the usage of variable fixation did not raise additional concerns with respect to standard fixation. The formation of a larger amount of mature callus suggests that fractures treated with variable fixation might have a higher probability to bridge the fracture gap. The conditions where its usage can be most beneficial for patients needs to be clinically defined.

Abstract Background and Aims Autologous keratinocyte sheets constitute an important component of the burn wound treatment toolbox available to a surgeon and can be considered a life‐saving procedure for patients with severe burns over 50% of their total body surface area. Large‐scale keratinocyte sheet cultivation still fundamentally relies on the use of animal components such as inactivated murine 3T3 fibroblasts as feeders, animal‐derived enzymes such as trypsin, as well as media components such as fetal bovine serum (FBS). This study was therefore aimed to optimize autologous keratinocyte sheets by comparing various alternatives to critical components in their production. Methods Human skin samples were retrieved from remnant operative tissues. Cell isolation efficiency and viability were investigated by comparing the efficacy of porcine‐derived trypsin and animal‐free enzymes (Accutase and TrypLESelect). The subsequent expansion of the cells and the keratinocyte sheet formation was analyzed, comparing various cell culture substrates (inactivated murine 3T3 fibroblasts, inactivated human fibroblasts, Collagen I or plain tissue culture plastic), as well as media containing serum or chemically defined animal‐free media. Results The cell isolation step showed clear cell yield advantages when using porcine‐derived trypsin, compared to animal‐free alternatives. The keratinocyte sheets produced using animal‐free serum were similar to those produced using 3T3 feeder layer and FBS‐containing medium, particularly in mechanical integrity as all grafts were liftable. In addition, sheets grown on collagen in an animal‐free medium showed indications of advantages in homogeneity, speed, reduced variability, and differentiation status compared to the other growth conditions investigated. Most importantly, the procedure was compatible with the up‐scaling requirements of major burn wound treatments. Conclusion This study demonstrated that animal‐free components could be used successfully to reduce the risk profile of large‐scale autologous keratinocyte sheet production, and thereby increase clinical accessibility.

To date, several types of airway stents are available to treat central airway obstructions. However, the ideal stent that can overcome anatomical, mechanical and microbiological issues is still awaited. In addition, therapeutic effect and self-elimination of these stents are desirable properties, which pose an additional challenge for development and manufacturing. We aimed to create a prototype bioresorbable tracheal stent with acceptable clinical tolerance, fit and biocompatibility, that could be tested in a rabbit model and in the future be further optimized to enable drug-elution and ensure local therapeutic effect. Twenty-one New Zealand White Rabbits received five different types of bioresorbable tracheal stents, 3D-printed from poly(D,L-lactide-co-ε-caprolactone) metacrylates. Various configurations were tested for their functionality and improved until the best performing prototype could undergo detailed in vivo assessment, regarding clinical tolerance, migration and biocompatibility. Previously tested types of 3D printed stents in our preliminary study required improvement due to several problems, mainly related to breakage, unreliable stability and/or migration within the trachea. Abandoned or refined pre-prototypes were not analyzed in a comparative way. The final best performing prototype stent (GSP2 (Group Stent Prototype 2), n = 8) allowed a transoral application mode and showed good clinical tolerance, minimal migration and acceptable biocompatibility. The good performance of stent type GSP2 was attributed to the helix-shaped surface structure, which was therefore regarded as a key-feature. This prototype stent offers the possibility for further research in a large animal model to confirm the promising data and assess other properties such as bioresorption. [ABSTRACT FROM AUTHOR]

Background: Muscle edema formation and inflammatory processes are early manifestations of acute rotator cuff lesions in sheep. Histological analysis of affected muscles revealed edema formation, inflammatory changes, and muscle tissue disruption in MRs. Hypothesis: Edema contributes to inflammatory reactions and early muscle fiber degeneration before the onset of fatty infiltration. Study Design: Controlled laboratory study. Methods: Osteotomy of the greater tuberosity, including the insertion of the infraspinatus tendon, was performed on 14 sheep. These experimental animal models were divided into 2 groups: a nontrauma group with surgical muscle release alone (7 sheep) and a trauma group with standardized application of additional trauma to the musculotendinous unit (7 sheep). Excisional biopsy specimens of the infraspinatus muscle were taken at 0, 3, and 4 weeks. Results: Edema formation was histologically demonstrated in both groups and peaked at 3 weeks. At 3 weeks, signs of muscle fiber degeneration were observed. At 4 weeks, ingrowth of loose alveolar and fibrotic tissue between fibers was detected. Fatty tissue was absent. The diameter of muscle fibers increased in both groups, albeit to a lesser degree in the trauma group, and practically normalized at 4 weeks. Immunohistology revealed an increase in macrophage types 1 and 2, as well as inflammatory mediators such as prostaglandin E2 and nuclear factor kappa-light-chain-enhancer of activated B cells. Conclusion: Early muscle edema and concomitant inflammation precede muscle fiber degeneration and fibrosis. Edema formation results from tendon release alone and is only slightly intensified by additional trauma. Clinical Relevance: This study illustrates that early edema formation and inflammation elicit muscle fiber degeneration that precedes fatty infiltration. Should this phenomenon be applicable to human traumatic rotator cuff tears, then surgery should be performed as soon as possible, ideally within the first 21 days after injury. [ABSTRACT FROM AUTHOR]

In vitro testing of implant materials bioactivity is important and the current methods take time. Here, the authors report on the development of a faster titration based method for assessing the mineralization activity of materials and validate the method in vitro and in vivo using titanium surfaces.

Reinforced hydrogels represent a promising strategy for tissue engineering of articular cartilage. They can recreate mechanical and biological characteristics of native articular cartilage and promote cartilage regeneration in combination with mesenchymal stromal cells. One of the limitations of in vivo models for testing the outcome of tissue engineering approaches is implant fixation. The high mechanical stress within the knee joint, as well as the concave and convex cartilage surfaces, makes fixation of reinforced hydrogel challenging. Methods. Different fixation methods for full-thickness chondral defects in minipigs such as fibrin glue, BioGlue®, covering, and direct suturing of nonenforced and enforced constructs were compared. Because of insufficient fixation in chondral defects, superficial osteochondral defects in the femoral trochlea, as well as the femoral condyle, were examined using press-fit fixation. Two different hydrogels (starPEG and PAGE) were compared by 3D-micro-CT (μCT) analysis as well as histological analysis. Results. Our results showed fixation of below 50% for all methods in chondral defects. A superficial osteochondral defect of 1 mm depth was necessary for long-term fixation of a polycaprolactone (PCL)-reinforced hydrogel construct. Press-fit fixation seems to be adapted for a reliable fixation of 95% without confounding effects of glue or suture material. Despite the good integration of our constructs, especially in the starPEG group, visible bone lysis was detected in micro-CT analysis. There was no significant difference between the two hydrogels (starPEG and PAGE) and empty control defects regarding regeneration tissue and cell integration. However, in the starPEG group, more cell-containing hydrogel fragments were found within the defect area. Conclusion. Press-fit fixation in a superficial osteochondral defect in the medial trochlear groove of adult minipigs is a promising fixation method for reinforced hydrogels. To avoid bone lysis, future approaches should focus on multilayered constructs recreating the zonal cartilage as well as the calcified cartilage and the subchondral bone plate.

Abstract Background Objective of this study is a feasibility-test comparing hock- and footpad-injection in rats with inoculated MatLyLu - adenocarcinoma tumor model. This study compares the development of an adenocarcinoma model (MatLyLu) in 12 Copenhagen rats. Two groups (n = 6) of animals were inoculated with 1 × 106 MatLyLu tumor cells solved in 0.1 ml NaCl either by footpad or hock injection. All animals were examined before tumor inoculation and before euthanasia using a 3.0 Tesla MRI. Histological evaluation of all organs was performed post mortem. Results Both types of injection were able to induce the adenocarcinoma model using MatLyLu tumor cells. The primary tumor could be visualized in MRI and confirmed histologically. Comparing the risk of reflux and the maximum injection volume during injection, the hock injection was superior to the footpad injection (less reflux, less anatomical restrictions for larger volumes). The hock injection induces a faster tumor growth compared to the footpad injection. As consequence the maximum level of long term discomfort after hock injection was reached earlier, even if it grew on a not weight bearing structure. Early lymph node tumor metastasis could not be observed macroscopically nor detected histologically. Therefore the reproducibility of the MatLyLu tumor model is questionable. Conclusion Hock injection is a feasible alternative technique compared with footpad-injection in rats. It provides a save and easy injection method for various early-terminated applications with the potential to increase animal welfare during tumor models in rats.

Tendon defects require multimodal therapeutic management over extensive periods and incur high collateral burden with frequent functional losses. Specific cell therapies have recently been developed in parallel to surgical techniques for managing acute and degenerative tendon tissue affections, to optimally stimulate resurgence of structure and function. Cultured primary human fetal progenitor tenocytes (hFPT) have been preliminarily considered for allogeneic homologous cell therapies, and have been characterized as stable, consistent, and sustainable cell sources in vitro. Herein, optimized therapeutic cell sourcing from a single organ donation, industrial transposition of multi-tiered progenitor cell banking, and preliminary preclinical safety of an established hFPT cell source (i.e., FE002-Ten cell type) were investigated. Results underlined high robustness of FE002-Ten hFPTs and suitability for sustainable manufacturing upscaling within optimized biobanking workflows. Absence of toxicity or tumorigenicity of hFPTs was demonstrated in ovo and in vitro, respectively. Furthermore, a 6-week pilot good laboratory practice (GLP) safety study using a rabbit patellar tendon partial-thickness defect model preliminarily confirmed preclinical safety of hFPT-based standardized transplants, wherein no immune reactions, product rejection, or tumour formation were observed. Such results strengthen the rationale of the multimodal Swiss fetal progenitor cell transplantation program and prompt further investigation around such cell sources in preclinical and clinical settings for musculoskeletal regenerative medicine.

Diverse cell therapy approaches constitute prime developmental prospects for managing acute or degenerative cartilaginous tissue affections, synergistically complementing specific surgical solutions. Bone marrow stimulation (i.e., microfracture) remains a standard technique for cartilage repair promotion, despite incurring the adverse generation of fibrocartilagenous scar tissue, while matrix-induced autologous chondrocyte implantation (MACI) and alternative autologous cell-based approaches may partly circumvent this effect. Autologous chondrocytes remain standard cell sources, yet arrays of alternative therapeutic biologicals present great potential for regenerative medicine. Cultured human epiphyseal chondro-progenitors (hECP) were proposed as sustainable, safe, and stable candidates for chaperoning cartilage repair or regeneration. This study describes the development and industrial transposition of hECP multi-tiered cell banking following a single organ donation, as well as preliminary preclinical hECP safety. Optimized cell banking workflows were proposed, potentially generating millions of safe and sustainable therapeutic products. Furthermore, clinical hECP doses were characterized as non-toxic in a standardized chorioallantoic membrane model. Lastly, a MACI-like protocol, including hECPs, was applied in a three-month GLP pilot safety evaluation in a caprine model of full-thickness articular cartilage defect. The safety of hECP transplantation was highlighted in xenogeneic settings, along with confirmed needs for optimal cell delivery vehicles and implantation techniques favoring effective cartilage repair or regeneration.

Background: Arthroscopic repair of large rotator cuff tendon tears is associated with high rates of retear. Construct failure often occurs at the suture-tendon interface. Patch augmentation can improve mechanical strength and healing at this interface. Purpose: To introduce a novel technique for suture-free attachment of an overlaid patch and evaluate its biomechanical strength and biological performance. Study Design: Descriptive and controlled laboratory studies. Methods: An established ovine model of partial infraspinatus tendon resection and immediate repair was used. After a nonwoven polyethylene terephthalate patch was overlaid to the resected tendon, a barbed microblade was used to draw fibers of the patch directly into the underlying tissue. In vivo histological assessment of healing was performed at 6 and 13 weeks after implantation. Ex vivo models were used to characterize primary repair strength of the suture-free patch fixation to tendon. Additional ex vivo testing assessed the potential of the technique for patch overlay augmentation of suture-based repair. Results: The in vivo study revealed no macroscopic evidence of adverse tissue reactions to the interlocked patch fibers. Histological testing indicated a normal host healing response with minimal fibrosis. Uniform and aligned tissue ingrowth to the core of the patch was observed from both the tendon and the bone interfaces to the patch. There was no evident retraction of the infraspinatus muscle, lengthening of the tendon, or tendon gap formation over 13 weeks. Ex vivo testing revealed that direct patch interlocking yielded tendon purchase equivalent to a Mason-Allen suture (150 ± 58 vs 154 ± 49 N, respectively; P =.25). In an overlay configuration, fiber interlocked patch augmentation increased Mason-Allen suture retention strength by 88% (from 221 ± 43 N to 417 ± 86 N; P <.01) with no detectable difference in repair stiffness. Conclusion: Testing in an ovine model of rotator cuff tendon repair suggested that surgical interlocking of a nonwoven medical textile can provide effective biomechanical performance, support functional tissue ingrowth, and help avoid musculotendinous retraction after surgical tendon repair. Clinical Relevance: The novel technique may facilitate patch augmentation of rotator cuff repairs. [ABSTRACT FROM AUTHOR]