Search

Ultrasonic vibration superimposed milling (UVSM) with an oscillating movement of the specimen in the direction of the tool axis is an efficient method for the generation of microstructured functional surfaces. The application of end milling cutters with a diameter smaller than the length and the width of the surface to be structured generally results in recuts and path overlaps. In order to avoid surface recutting, a small lead angle was realized by slightly tilting the ultrasonic system with the specimen. The overlapping area of two adjacent paths was kinematically simulated for different widths of cut (from 70% to 90% of the tool diameter). Cutting experiments were carried out by UVSM of X46Cr13 and X40CrMoV5-1 steel specimens to investigate the influence of the width of cut on the surface generated in the overlapping area and also the adherence of a subsequently deposited CVD diamond layer. For this purpose, 3-D laser scanning microscopy and SEM analysis were applied. The knowledge gained allows for designing UVSM processes, especially regarding 3-D freeform surfaces with defined microstructures subjected to CVD diamond coating. [ABSTRACT FROM AUTHOR]

Ultrasonic vibration superimposed face milling enables the generation of predefined surface microstructures by an appropriate setting of the process parameters. The geometrical reproducibility of the surface characteristics depends strongly on the plastic material deformation. Thus, the precise prediction of the emerging surface microstructures using kinematic simulation models is limited, because they ignore the influence of material flow. Consequently, the effects of plastic as well as elastic deformation are investigated in depth by finite element analysis. Microstructured surfaces resulting from these numerical models are characterized quantitatively by areal surface parameters and compared to those from a kinematical simulation and a real machined surface. A high degree of conformity between the values of the simulated surfaces and the measured values is achieved, particularly with regard to material distribution. Deficits in predictability exist primarily due to deviations in plastic deformation. Future research can address this, either by implementing a temperature consideration or adapting specific modeling aspects like an adjusted depth of cut or experimental validated material parameters. [ABSTRACT FROM AUTHOR]

Ultrasonic vibration superimposed face milling enables the generation of predefined surface microstructures by an appropriate setting of the process parameters. The geometrical reproducibility of the surface characteristics depends strongly on the plastic material deformation. Thus, the precise prediction of the emerging surface microstructures using kinematic simulation models is limited, because they ignore the influence of material flow. Consequently, the effects of plastic as well as elastic deformation are investigated in depth by finite element analysis. Microstructured surfaces resulting from these numerical models are characterized quantitatively by areal surface parameters and compared to those from a kinematical simulation and a real machined surface. A high degree of conformity between the values of the simulated surfaces and the measured values is achieved, particularly with regard to material distribution. Deficits in predictability exist primarily due to deviations in plastic deformation. Future research can address this, either by implementing a temperature consideration or adapting specific modeling aspects like an adjusted depth of cut or experimental validated material parameters.

The importance of functional surfaces is continuously growing in the context of increasing demands on the sustainability of performance, resource efficiency and manufacturing costs of technical systems. For example, microstructured substrate surfaces can contribute to enhance the adhesion of layers, which in turn ensure the wear protection of a highly loaded component. Many microstructuring processes require a system change, entailing high costs. However, the ultrasonic vibration superimposed machining (UVSM) can be implemented as a finishing process. Due to its defined cutting-edge geometry and kinematics, UVSM represents a suitable method for a reliable generation of predefined surface microstructures. In order to optimize the process regarding the tool wear behavior and thus the geometrical characteristics of the surface microstructure, experimental investigations are carried out to find the most suitable combination of heat treatment condition of the martensitic stainless-steel X46Cr13 and various cutting materials. A vibration system for workpiece-side excitation is used for the experimental cutting tests. The most promising results were obtained within the combination of cemented carbide as a cutting tool and soft annealing as a heat treatment condition. They serve as a base for extensive investigations on the effects of substrate microstructuring to the adhesion of chemical vapor deposition (CVD) diamond layers to steel. [ABSTRACT FROM AUTHOR]

Diamond coatings applied by chemical vapor deposition (CVD) provide extraordinary properties concerning hardness and wear resistance, which enables an increase of the performance or lifetime of highly stressed components. In particular, the combination of steel substrates and diamond coatings allows for numerous applications in several sectors of industry. However, there are significant challenges considering the coating adhesion strength. For example, the mismatch concerning the thermal expansion of steel and diamond commonly leads to a delamination of the coating. Thus, a suitable pre-treatment of the substrate surface is compulsory. With the aim of improving CVD diamond coating adhesion, ultrasonic vibration superimposed machining (UVSM) is applied when doing face milling on steel X46Cr13 specimens. The vibration direction is parallel to the tool axis and perpendicular to the feed direction. The tool wear and the surface microstructure are determined by 3D laser scanning microscopy. The investigations show, that predefined microstructuring of the substrate surface by UVSM contributes to an enhancement of the CVD diamond coating adhesion, especially regarding coatings with a thickness up to 10 µm. This can be referred to a better distribution or a reduction of thermally induced residual stresses in the diamond layer. However, a reliable generation of deterministic microstructures by UVSM significantly depends on the wear behavior of the tool. Uncoated cemented carbide grades exhibit considerable deficits reflecting in rapid tool wear. Therefore, adapted tool coatings are experimentally investigated, which result in an increase of the tool life and a reduction of the geometrical deviations of the microstructures. With an appropriate system of surface microstructure and coating, for example for tribological applications substantial improvements in terms of wear resistance and coefficient of friction are expected. [ABSTRACT FROM AUTHOR]

The importance of functional surfaces is continuously growing in the context of increasing demands on the sustainability of performance, resource efficiency and manufacturing costs of technical systems. For example, microstructured substrate surfaces can contribute to enhance the adhesion of layers, which in turn ensure the wear protection of a highly loaded component. Many microstructuring processes require a system change, entailing high costs. However, the ultrasonic vibration superimposed machining (UVSM) can be implemented as a finishing process. Due to its defined cutting-edge geometry and kinematics, UVSM represents a suitable method for a reliable generation of predefined surface microstructures. In order to optimize the process regarding the tool wear behavior and thus the geometrical characteristics of the surface microstructure, experimental investigations are carried out to find the most suitable combination of heat treatment condition of the martensitic stainless-steel X46Cr13 and various cutting materials. A vibration system for workpiece-side excitation is used for the experimental cutting tests. The most promising results were obtained within the combination of cemented carbide as a cutting tool and soft annealing as a heat treatment condition. They serve as a base for extensive investigations on the effects of substrate microstructuring to the adhesion of chemical vapor deposition (CVD) diamond layers to steel.