Search

The road that crosses the Haibat Sultan Mountain in the northern part of Iraq; is one of the dangerous roads in this region. To perform a slope stability analysis for the dangerous parts of the road, we have used Bejerman’s Method. We have reviewed satellite images of the road and all those potential areas were checked in the field; accordingly, eleven stations were recognized. Landslide Possibility Index was determined at the studied stations following Bejerman’s field method. The road climbs the southern face (dip slope) of the mountain through very hard carbonate rocks of the Pila Spi Formation, where the bedding planes daylight in the slope face near the road cuts. This produced many large landslides. Along the northern face of the mountain, the road runs through soft clastic rocks where joint planes in the rock mass intersect and daylight in the slope face near the road cut. In order to prevent future wedge failures, a 30 m offset was created from the toe of the slope to the road. In almost all cases, the Landslide Possibility Index indicated a moderate to very high likelihood for failure along all road cuts.

This paper presents the analyses of toppling response of layered reverse-dip slopes under the influence of geometric factors of slope angle, strata thickness and dip. The toppling response of reverse-dip slopes under different geometric factors is obtained by using the discrete element code UDEC. Then, a prediction model for toppling deformation is developed by utilizing support vector machine and the toppling-prone combinations of these geometric factors are determined from a total of 120 samples of reverse-dip slopes. The study has shown that the geometric model is a quarter of a spheroid with a slope angle of 80°, a strata dip of 80°, and a strata thickness of 0.19 m as the center. The length of the long equatorial radius of the spheroid is 31° (strata dip axial), that of the short equatorial radius is 21° (slope angle axial), and the polar radius is 0.075 m (strata thickness axial). And the ratio of long equatorial radius, short equatorial radius, and polar radius is 2.48:1.68:1.00.

Rocky desertification is an economic, social, and environmental problem, which refers to the processes and human activities that transform a karst area covered by vegetation and soil into a rocky landscape. The effects of different types of soil cover on ecohydrological processes during the revegetation of areas undergoing karst rocky desertification remain unclear. Taking different measures for different ecohydrological situations will benefit re-vegetation in karst rocky desertification areas. Monthly/heavy rainfall hydrochemical data and the δ13C of dissolved inorganic carbon (DIC) in karst water samples from January 2017 to December 2019 were obtained. This revealed the controlling mechanisms on hydrochemical processes by δ13CDIC under different soil cover conditions in the dip/anti-dip slopes of a karst trough valley in Ganxi Town, Chongqing City, southwestern China. Hydrochemical variations are controlled by climate, soil, and vegetation and show clear seasonality. The δ13CDIC values (−16.88‰ to −3.49‰) in the study area were higher than the theoretical value (−14.00‰). In addition, it was observed that rain accelerated soil erosion (R2=0.7) in the karst trough valley and human activities (exogenous acid) resulted in DIC loss. The slopes, soil, and bare rock cover on the dip slope were different from that on the anti-dip slope, leading to the difference in their re-vegetation statuses. In this study, we found that different vegetation restoration schemes and treatment measures should be implemented between the dip and anti-dip slope. The protection of soil and water resources, especially soil, is the key to ecological restoration in rocky desertification areas.

Landslide dams can be very dangerous, with inundation occurring via rising waters upstream, and flooding downstream via dam breaching. Here, we report on a landslide that dammed the Mangapoike River in eastern North Island, New Zealand. The landslide is a low-angle wedge failure in the Miocene weak rock sandstones and mudstones of the Tolaga Group, forming a landslide dam (volume c. 8 million m3) and a lake 50 m deep with a surface area of 0.35 km2, before explosives were used to form a dam spillway to decrease lake level. The landslide formed along an escarpment in northwest-dipping sandstones, and is characterised by a linear lateral scarp, a headscarp, and a bedding-plane rupture surface, which controlled the landslide block geometry. The headscarp and lateral scarp have developed along propagating vertical fractures. The slide surface is a smoothed, northwest-dipping bedding plane, and intersects the vertical fractures in the lateral scarp, forming a wedge. While the principal failure mechanism was sliding involving a single large wedge-shaped block, the rapid movement led to disintegration of most of the block. Part of the detached slide block remained intact, but most of the displaced mass forming the landslide dam is disaggregated blocks in a sandy-silty matrix. Rainfall and meteoric groundwater probably did not initiate failure. Instead, river incision of the dip slope toe, and overpressurisation of fluids that are known to accumulate in sandstones overlain by impermeable mudstones in the region, probably decreased the effective stress along the existing bedding plane, initiating failure.

On May 12, 2019, a landslide occurred near a construction site of a reservoir dam along the left bank of the Wulong River, Qinghai Province, China. Video footage showed that the entire failure process of the landslide lasted for 15 min. Although an excavator that parked on the foundation pit was buried and the Wulong River was blocked, this landslide did not cause any casualties. Based on field investigations, 3D laser scanning, unmanned aerial vehicle observations, and borehole surveys, this study aims to reveal the cause and initiation mechanisms of the landslide. The landslide developed on a typical dip slope with thick-bedded conglomerates intercalated with a few mudstone layers. The slide mass mainly consisted of conglomerates with a dip angle varying from 20 to 40°, failing along bedding plane contacts with the underlying muddy intercalation. Numerous tension cracks had developed in the upper part of the slope due to stress relaxation during the process of bank slope evolution associated with rapid river incision. These cracks damaged the integrity of the rock mass and promoted rapid rainfall infiltration. The water infiltrated into the slope and deteriorated the mechanical properties of the rock mass, which resulted in long-term deterioration of the slope stability conditions. In addition, the temperature of Tongren County was below zero for 5 months in a year, hence the freeze–thaw cycle of the water filled in the cracks would have reduced the shear strength further. There were 10 days of continuous rainfall before the landslide occurred, and the cumulative precipitation in 2018 and 2019 was also significantly more than that of previous years. Three primary factors are involved in the landslide event: (1) thick-bedded conglomerates intercalated with a few mudstone layers with contrasts in strength, (2) development of numerous relaxation cracks, and (3) long-term rainfall accumulation.

The major regions of Taiwan consist of high-relief terrain exposed to frequent typhoons and earthquakes. Recently, thousands of potential large-scale landslides have been delineated via remote sensing analysis and field surveys. However, little attention has been paid to the stability of colluvium, which is a potential hazard. This study investigated a paleo-rockslide site in detail and proposes a geological model to explain the failure mechanism. The studied area is in Jiasian, Southern Taiwan, and the site is a dip slope consisting of Miocene sedimentary rocks. Detailed topographic features, including residual slip surfaces, platforms, scarps, and colluviums, are identified using the slope map of a 1- m airborne remotely sensed digital elevation model. Platforms beneath the residual slip surfaces represent the topographic features of the paleo-rockslide, an interpretation validated by field works and core analysis. The platforms consist of a displaced rock mass (DRM) with a gentle bedding dip angle and interbedded structure that has been preserved. A geological model is established according to the data compiled; outcrops of DRM and colluviums on bedrock were delineated in the geological map and profiles. Outcrops of shear off, buckling, and compressive ridges within the alternating sandstone and shale are distributed at the toe of the residual slip surfaces. A geological model with identified topographic features is adopted to establish the geomorphological evolution of the site. A buckling-induced rockslide model in the dip slope of the interbedded layers is proposed, and potential future slope failure scenarios can be evaluated using the geomorphological evolution model.

A slow-moving landslide on the Huafan University campus, which is located on a dip slope in northern Taiwan, has been observed since 1990. However, reliable monitoring data are difficult to acquire after 2018 due to the lack of continuous maintenance of the field measurement equipment. In this study, the multitemporal interferometry (MTI) technique is applied with Sentinel-1 SAR images to monitor the slow-moving landslide from 2014–2019. The slow-moving areas detected by persistent scatterer (PS) pixels are consistent with the range of previous studies, which are based on in situ monitoring data and field surveys. According to the time series of the PS pixels, a long period gravity-induced deformation of the slow-moving landslide can be clearly observed. Moreover, a short period seasonal surface fluctuation of the slow-moving landslide, which has seldom been discussed before, can also be detected in this study. The seasonal surface fluctuation is in-phase with precipitation, which is inferred to be related to the geological and hydrological conditions of the study area. The MTI technique can compensate for the lack of surface displacement data, in this case, the Huafan University campus, and provide information for evaluating and monitoring slow-moving landslides for possible landslide early warning in the future.

Geological structures precondition hillslope stability as well as the processes and landslide mechanisms which develop in response to deglaciation. In areas experiencing glacier retreat and debuttressing, identifying landslide preconditions is fundamental for anticipating landslide development. Herein, the ~ 150 M m3 Mueller Rockslide in Aoraki/Mount Cook National Park, New Zealand, is described; and we document how preconditions have controlled its morphology and development in response to thinning of the adjacent Mueller Glacier. A combination of geomorphological and geotechnical mapping—based on field, geophysical and remote sensing data—was used to characterise the rock mass and morphology of the rockslide and surrounding hillslope. Mueller Rockslide is identified as a rock compound slide, undergoing dominantly translational failure on a dip slope. The crown of the rockslide is bounded by several discontinuous, stepped scarps whose orientation is controlled by joint sets; these scarps form a zone of toppling that is delivering rock debris to the main rockslide body. Surface and subsurface discontinuity mapping above the crown identified numerous joints, fractures and several scarps that may facilitate continued retrogressive enlargement of the rockslide. The presence of lateral release structures, debuttressing of the rockslide toe and steeply dipping bedding suggest that the rockslide may be capable of evolving to a rapid failure.

To clarify the scale effect of slope deformation, this study investigates the behaviors of dip slopes with various heights and geological properties using centrifuge and numerical modeling. Three types of physical and numerical models with different rock layer thicknesses and weak plane angles were constructed for analysis and validation. The models were subject to toe submersion to simulate the wetting deterioration condition. Based on the analysis results, the deformation, sliding, and debris accumulation of small slopes (a few meters high) may be insignificant. However, the deformation behaviors of higher slopes with the same angle (with a height of tens to a hundred meters) can be more severe and affect the whole slope, especially if the slope has a high weak plane angle with alternating thin rock layers. Some early warning signs, such as bulging-induced tension cracks close to the toe or the relative sliding of layers at the slope surface or crest, can produce more massive landslides or debris accumulation of the dip slopes, especially for high slopes.

Anti-dip slope that fails in the form of flexural toppling is commonly encountered in rock engineering. This paper presents an approach to calculate the local failure probability of the anti-dip slope susceptible to flexural toppling. The realization of this approach consists of four major steps: (1) establishing geo-mechanical model of the slope and generating physical parameters randomly using Monte Carlo simulation, (2) determining the demarcation of the toppling and sliding failure zones, (3) evaluating the stability state of each single column, and (4) deriving the local failure probability by an iterative calculation. A case study of the Mari landslide is analyzed by employing the proposed approach, and the Maxwell model is applied to reduce physical parameters with time. The results show that the instability grade increases gradually throughout the whole evolution process of the slope. In the incipient stage, particular attention should be paid to the middle–upper columns, which have the highest failure probabilities. However, as the slope deformation increases, all the columns should be taken into account since they have approximately the equal possibility of failure. A simplified slope model is employed to perform a parametric analysis. The results show that (1) the local failure probability of the slope tends to decrease with increases in the rock friction angle, rock tensile strength or interface friction angle, while increasing the rock unit weight leads to a higher probability of local failure; (2) the computation results are more sensitive to the uncertainty in the interface friction angle than that in the other three above-mentioned parameters; and (3) the maximum failure probability depends on the geometric parameters, including the column interface angle, slope angle, crest angle, slope height and column thickness.

The past decade has witnessed increasing case studies on the application of 3D discrete element modeling to assess potential rockslide disasters. The assessment is usually based only on the influence area related to kinematic process and final deposition by the simulation. Currently, the hazard of the rockslide-structure interaction is not well defined, and only a few studies have quantality this behavior with a parametric analysis. A dip slope disaster case history on 18 August 1997 in Taiwan was simulated in this study using discrete element method (DEM). The landslide intensely damaged a five-floor building complex of the Lincoln community and caused 28 death. This study first gathered historical aerial images, geology maps of 1:50,000 scale, post-disaster investigation reports, and in-situ photos to clarify the geological and geometry conditions of the dip slope and its spatial relationship to the Lincoln community. Most importantly, a 3D geomechanical model was developed for the numerical study. With the advantage of DEM analysis on large deformation problems, the entire impact process of the dip slope failure was simulated, starting from rock mass sliding to collision and breaking during movement, impacting on the structural buildings and progressive failure of the structures. The simulated results agree well with the field observation after the incident in 1997. The parametric results show that the configuration of the geological discontinuity dominates the magnitude of the potential sliding block, and the rockslide-structure interactions are affected by the relative location between rock slope and buildings and the strengths of rock mass and structure elements. Overall, the 3D DEM-based simulation provides qualitative information on the impact process of the rockslide and the damage states of the building complex. This validated numerical approach can be a valuable tool for assessing the building vulnerability to rockslide with scenario study.

As the scale and depth of mines increase, large deformations of high-steep slopes progressively become prominent. Compared with the ordinary cables, negative Poisson’s ratio (NPR) cables can provide a constant resistance force and high deformation inhibition during slope deformation, avoiding the occurrence of slope instability hazards. Consequently, the control effects on the toppling failures of slopes were necessary to be researched. Changshanhao open-pit gold mine was taken as an example; based on the field geological investigation and rock mechanics testing, a three-dimensional engineering geological model of open-pit mine was constructed. Subsequently, the stability of open pit in current situation and final boundary situation was estimated with FLAC3D software, for the potential slope vulnerable areas to be comprehensively identified. Finally, the control effects of ordinary cables and NPR cables on the instable W13 slope section were compared and studied through FLAC3D simulations, and the reinforcement effects of NPR cable on the anti-dip slope were proved as significant; meanwhile, the corresponding reinforcement methods in the failure mine areas were proposed, laying a reference for the instability failure control and reinforcement of similar anti-dip slopes.

Recent studies of the form and development of rock slopes have focused on the properties of materials as geomorphic controls. In the absence of structural controls, rock mass strength has been found to be an important determinant of slope form. In the fold mountains of the southern and southwestern Cape Province, South Africa, rock slopes on quartzite have developed to forms controlled by rock mass strength (strength equilibrium slopes), structure, and denudational processes. Contingency table analysis indicates that the rock properties of greatest significance as determinants of the form of strength equilibrium slopes are intact rock strength and the spacing of joints and other geological discontinuities. On undercut, unbuttressed rock masses and on buttressed (dip slope) forms, parting roughness is a key factor in slope development by virtue of the effect of parting roughness on shear strength. Roughness measurements, tilt tests, and field observation indicate that the effective friction angle of the quartzite is approximately 55°.

A large catastrophic rock avalanche with a total volume of ~18.0 × 106 m3 occurred at 5:38 am, 24th June 2017, at Xinmo Village, Maoxian, Sichuan, China, resulting in 102 casualties (10 deaths, 3 injuries, and 89 missing). We have been conducting a geological and geomorphological investigation in and around the Xinmo landslide site since 2015, and we present our results here, including data obtained before and after the landslide event. The landslide, which had an initial volume of 4.46 × 106 m3 of its source area, was induced by rainfall on a previous landslide scar near the ridge top. This initial landslide then struck and remobilized older landslide deposits in the middle and lower parts of the slope, which subsequently buried Xinmo Village at the landslide toe. The landslide occurred on a dip slope of Triassic calcareous psammitic and pelitic schists. The bedding plane, which dips downslope to the south with an orientation of N80°W/48°S, and high-angle NE–SW striking joints bounded the landslide source area at its base and sides, respectively. Satellite image analysis and field observations of the slope of the landslide scar before and after the landslide strongly suggest that the beds in the source area had already begun gravitationally deforming (e.g., buckling) prior to the 2017 landslide. Moreover, pits on the slip surface were likely the result of the dissolution of calcareous material. Dissolution probably reduced the rock strength along the bedding plane. A rainfall event from the 16th to 24th of June 2017 probably dominated the groundwater drainage, and finally triggered the catastrophic rock avalanche. In addition to the 2017 landslide, the hillslope just to the east of the Xinmo landslide exhibits pronounced gravitational slope deformation, including “A-tent”-like structures and warps induced by buckling. This suggests that this slope could also fail like the Xinmo rock avalanche during a future rainfall or earthquake event.

A dip slope contains weak planes in the same dip direction along the slope face. In this study, a discrete element simulation was implemented to investigate the behavior of a dip slope under shaking table tests. The simulated dip slope model was first verified by testing under different horizontal excitations. Then, the influence of the slope angle and dynamic force on the deformation characteristics of the dip slopes was explored. The simulations provide detailed descriptions of the deformation processes and potential sliding mechanisms associated with the dip slopes. The results of this study are summarized as follows: (1) Two types of slope sliding, namely differential and complete, were recognized. The model with a dip angle lower than 20° was more stable, and differential sliding developed gradually during external excitation. In the model with a dip angle higher than 20°, the external excitation easily triggered complete sliding. (2) For threshold slope angles higher than 20°, the behavior of the dip slope model changed from deformation to sliding, and the displacement within the models increased with increasing slope angle. (3) An increase in frequency led to a decrease in the trigger time for slope sliding. In addition, the slope angle was negatively correlated with the triggering time for sliding. (4) The amplification factor of peak ground displacement (PGD) increased as the slope angle increased. The amplification factors corresponding to low excitation frequencies were considerably lower than those for high excitation frequencies. In contrast to the trends for PGD, the amplification factor of peak ground acceleration (PGA) decreased as the slope angle increased.

At 5 am 24th June 2017, a catastrophic landslide hit Xinmo Village, Maoxian County, Sichuan Province, China. The slide mass rushed down from an altitude of 3400m and traveled 2700 m in a high velocity. The 13 million m3 deposition buried the whole village and caused about 100 deaths. The source area of the landslide is located in a high steep slope, average slope angle is 40o and maximal angle is 65o. The strata are interbedded Triassic Zagunao Formation metamorphic sandstone and slate with the dip slope angle of 45°. Based on high-resolution satellite remote sensing image, UAV image, DEM data, and field investigation, failure mechanism, travel features, and deposit characteristics were analyzed. The results showed that this landslide was influenced by Songpinggou Fault zone. According to the topography before the failure, the landslide is located in the back scarp of an antecedent landslide induced by Diexi Earthquake in 1933. The bedding slope provided potential rupture surface. Historical seismic activities and long-term gravitational deformation caused rock mass accumulated damages. Weathering and precipitation weakened the rock mass and finally induced shearing and tension failure. A huge block detached from the top rock slope, pushed the past landslide deposits in the middle part, rushed out of the slope bottom in a high velocity and buried the Xinmo Village. The rapid movement entrained and brought the soil into the Songping Gully which recoiled with and bounced back from the opposite mountain.

This study investigated the effect of internal discontinuity on the dynamic response of a dip slope and evaluated the performance of Newmark’s theory on the sliding of a dip slope with multi-slip planes. A series of shaking table tests were performed under various geometric conditions to explore the dynamic behavior of a dip slope under different external excitations. The test results, including for deformation processes and critical accelerations, under various slope angles, slope sizes, and seismic intensities were examined and further compared with Newmark’s theory. The results of this study are summarized as follows: (1) two types of slope sliding (differential and complete) were determined. (2) Increasing the slope angle and the height of sliding mass tended to shorten the duration of slope deformation. (3) Critical acceleration of the slope increased gradually with increasing peak ground accelerations of input excitations; when the slope height and dip angle increased, the critical acceleration decreased. (4) The triggering time became earlier as the frequency of input excitation increased; the magnitude of sliding mass greatly depended on the amplitude of the input excitation. (5) By comparing critical acceleration between the experimental and theoretical results, Newmark’s theory was determined to overestimate critical acceleration during seismic-induced dip slope failure. This may cause unsafe evaluations, and sliding along existing discontinuities develops more easily in reality.

The Cotswold Hills, southwest UK, are properly described as a cuesta, with a steep, west-facing scarp slope and a plateau-like dip slope. Drainage reflects this surface morphology, with most rivers flowing southeast along topographic and stratigraphic dip. Here, we compare two superficially highly similar rivers – the Frome and Churn – whose sources are nearly coincident, but whose behaviour dramatically diverges thereafter. We examine longitudinal profiles, channel steepness, predicted discharge, and valley shapes, using digital topographic data. River discharge and water hardness/temperature values were obtained at seven sites on the Churn and nine on the Frome over a two-year sampling campaign, delineated into summer and winter phases. Nearly 100 borehole records were interrogated from the two catchments in order to assess groundwater level variations. The Frome, flowing west against regional dips, develops a steep course and has carved a deep and wide valley that exposes the full sequence of Cotswold Jurassic stratigraphy. On the other hand, discharge and channel gradients are lower for the dip-slope Churn, whose valley exposes less stratigraphy and fewer springs. Our measurements of river water hardness and temperature suggest that a greater proportion of groundwater flows into the Frome, regulating discharge and maintaining baseflow over summer. We suggest that flank uplift of the Cotswolds is at least part of the reason for the higher incision rates of the River Frome, leading to its intersecting a greater number of highly transmissive fractures that contribute to its discharge. In turn, the increased discharge could positively impact local incision rates.

On June 24, 2017, a catastrophic landslide (Xinmo landslide) occurred on the left bank of Songping river in Diexi town, Sichuan Province, China. Based on field investigations, this paper tries to reveal the cause and mechanism of the initiation and development of the Xinmo landslide. Xinmo landslide is located in the so called “Minshan block.” This tectonic block is very active and generates many earthquakes. Among them, the 1933 Diexi Ms 7.5 earthquake which had an indispensable effect on the occurrence of the Xinmo landslide, whose distance to the recent Xinmo landslide is only 8.7 km. The 1933 earthquake triggered the collapse of the Qianxin gully, which damaged the rock mass forming the source of the Xinmo landslide and creating a free prominent ridge. The later 1976 Songpan Ms 7.2 earthquake and the 2008 Wenchuan Ms 8.0 earthquake further damaged the integrity of the rock mass in the source area of the 2017 Xinmo landslide. The Xinmo landslide developed on a typical bedding dip slope with metasandstone intercalated with a few thin bedded slate layers. The slate intercalation gives the slope a very low shear strength in the dip direction and the long term rainfall may have softened the slip zone and the locked section. These two aspects have promoted the occurrence of Xinmo landslide.

Slope failure is a widely observed phenomenon in the mountainous areas in Taiwan due to rainy climatic and fragile geological conditions. Landslides easily occur after intense rainfall, especially from typhoons, and, accordingly, cause a great loss of human life and property. At the northern end of the Western Foothill belt in northern Taiwan, Huafan University is founded on a dip-slope about 20° toward the southwest composed of early Miocene alternations of sandstone and shale. Data from continuous monitoring using inclinometers and groundwater gauges reveal that 6–10 mm/month of slope creeping occurs, and a potential sliding surface is then detected about 10–40 m beneath the slope surface. To understand the potential runout process of the dip-slope failure at the campus, particle flow code 3D models based on a discrete element method are applied in this study. Results of the simulation reveal a critical value of the friction coefficient to be 0.13 and that more than 90% of the campus buildings will slide down in 100 s when the friction coefficient is reduced to half the critical value. The weakening of the shear zone due to the rise of groundwater during rainstorms is assumed to be the main factor. Some suggestions for preventing landslide disasters are to construct catchpits to drain runoff and lower the groundwater table and to install a sufficient number of ground anchors and retaining walls to stabilize the slope.

Several related pre-event environment indices coupled with a 200-year event of Typhoon Morakot were used in this study to analyse landslide risk/scale for mapping and verifying the danger grade of watershed landslides. Risk analysis was modelled using maximum daily rainfall of the tested event as the hazard factor, and a complex indicator derived from indices of return period, road development and green deterioration as the vulnerability factor. The vulnerability factor was then modified using the slope to adjust the weight for excluding the flat areas and increasing impact of steep areas. A comprehensive indicator integrated from indices of river concave, headward erosion and dip slope was provided as the hotspot of potential large-scale landslides which were modified by vegetation index to correct sediment yield due to antecedent effects. Finally, sites with high potential large-scale landslide could be interpreted by the danger grade calculated from collapse risk/scale analysis. The results show that the higher the danger grade, the greater the collapse ratio; and the coefficient of determination for the relationship is greater than 0.9. The model developed in this study for accurately estimating the risk/scale of rainfall-induced landslide can be fulfilled.

Dip-slope mapping is a fundamental task for landslide investigation and mitigation. However, most dip-slope mapping methods involve visual interpretations and manual processes that are inevitably subjective and time consuming. The advent of high-resolution digital elevation models (DEM) and increases in computing power have provided opportunities to improve the dip-slope mapping process. This study proposes a polygon auto-tracing method for generating dip-slope maps based on airborne Light Detection and Ranging (LiDAR) data and a customized spatial analysis toolset developed in Python. This method requires the input of strata boundaries produced for sedimentary terrain based on 2 m resolution LiDAR DEMs. The method begins by deriving the raster layer of the dip direction of the bedding, and it then executes a series of raster calculations among the three raster layers slope, aspect, and dip direction to extract the dip-slope raster cells. Using the clustering pattern of the dip-slope raster cells, we implement the Point-Density analysis tool to determine the dip-slope areas. The ArcGIS ModelBuilder platform is used to lay out an automated workflow for the proposed polygon auto-tracing method using the customized toolset. For demonstration purposes, we successfully mapped 298 dip slopes in the study area, which frequently experiences dip-slope landslides and is located in the sedimentary terrain of northern Taiwan. The dip-slope mapping results were compared and validated against two government-funded visually interpreted dip-slope maps. Our dip-slope mapping results were also used in a daylight analysis along major freeways to identify potential locations of daylighted dip slopes.

Based on the combination of FLAC3D software and strength reduction method, the applicability of three kinds of instability criterion of the stability of dip slopes with interbeddings of weak and hard rocks is studied. Then the failure process, failure mode and stability of the slopes are analyzed. The results show that: (1) the maximum unbalance rate affects the final calculated results; there is no certain relation between the convergence of calculation and the slope stability. The convergence of the displacement curves of key points and the ultimate displacement values should also be concerned to determine the slope stability. The maximum unbalance rate and the amplitude of the reduction affect the determination of the characteristic point in the displacement curve. It is difficult to quantitatively evaluate the shear strain rate when judging the slope stability, the judgment is not convenient and the error is large. Combining with calculation convergence criterion and feature point displacement mutation criterion is helpful to improve the accuracy of judgment on the limit state of the slope. (2) Slope deformation and failure process can be roughly divided into four stages qualitatively; the rock mass has buckling failure can be divided into three stages according to the deformation characteristics. The potential shear export of slope with buckling failure locates above the slope toe. Different combinations of weak and strong rock thickness does not affect the failure mode of slope, which all bellows to buckling failure mode, but it will affect the slope stability coefficient; with the increase of the thickness of strong rock and weak rock, the stability coefficient increases. If the thickness of the strong rock increases, the stability coefficient increases as well when the thickness ratio is constant.

The 17 June 2017 rock avalanche in the Karrat Fjord, West Greenland, caused a tsunami that flooded the nearby village of Nuugaatsiaq and killed four people. The disaster was entirely unexpected since no previous records of large rock slope failures were known in the region, and it highlighted the need for better knowledge of potentially hazardous rock slopes in remote Arctic regions. The aim of the paper is to explore our ability to detect and locate unstable rock slopes in remote Arctic regions with difficult access. We test this by examining the case of the 17 June 2017 Karrat rock avalanche. The workflow we apply is based on a multidisciplinary analysis of freely available data comprising seismological records, Sentinel-1 spaceborne synthetic-aperture radar (SAR) data, and Landsat and Sentinel-2 optical satellite imagery, ground-truthed with limited fieldwork. Using this workflow enables us to reconstruct a timeline of rock slope failures on the coastal slope here collectively termed the Karrat Landslide Complex. Our analyses show that at least three recent rock avalanches occurred in the Karrat Landslide Complex: Karrat 2009, Karrat 2016, and Karrat 2017. The latter is the source of the abovementioned tsunami, whereas the first two are described here in detail for the first time. All three are interpreted as having initiated as dip-slope failures. In addition to the recent rock avalanches, older rock avalanche deposits are observed, demonstrating older (Holocene) periods of activity. Furthermore, three larger unstable rock slopes that may pose a future hazard are described. A number of non-tectonic seismic events confined to the area are interpreted as recording rock slope failures. The structural setting of the Karrat Landslide Complex, namely dip slope, is probably the main conditioning factor for the past and present activity, and, based on the temporal distribution of events in the area, we speculate that the possible trigger for rock slope failures is permafrost degradation caused by climate warming. The results of the present work highlight the benefits of a multidisciplinary approach, based on freely available data, to studying unstable rock slopes in remote Arctic areas under difficult logistical field conditions and demonstrate the importance of identifying minor precursor events to identify areas of future hazard.

Bedding dip has an important influence on soil detachment and flow hydrodynamics in a karst trough valley. The laboratory rainfall simulation was conducted with three bedding dips (bare slope, dip slope and anti-dip slope) under three rainfall intensities (30, 60, 90 mm h−1). The characteristics of soil detachment and hydrodynamic parameters were assessed, including water flow shear stress, stream power, unit stream power and unit flow energy. The significant effects of bedding dips and rainfall intensities and their interactions on soil detachment and hydrodynamic parameters were examined. The results showed that (1) the soil detachment rate decreased with increasing rainfall duration, and the soil detachment rate in 30° bedding dip of dip slope was much larger than those in bare slope and anti-dip slope in most rainfall intensities; (2) the 60° bedding dip of dip slope was the threshold that controlled the stream power, unit stream power and unit flow energy increased or decreased under different rainfall intensities; and (3) the soil detachment rate had extremely significant positive power relationships with water flow shear stress, stream power, unit stream power and unit flow energy. Meanwhile, the stream power was the most suitable parameter for predicting soil detachment in a karst trough valley slope. Therefore, these results could provide useful information for soil erosion prediction in a karst trough valley.

Existing fan-delta depositional models for lacustrine basins do not adequately address significant wave- and storm-related processes. However, in many lakes, such high-energy processes can be effectively driven by winds. As such, the prevailing wind direction determines the propagation direction of wind-induced waves. Observations from modern examples show that wave-dominated deposits commonly exist on one side of the lake, and their sedimentary processes are completely distinct from those on the opposite side. However, equivalent deposits have seldom been identified from subsurface data. We present an ancient example from the Upper Tongbomiao Formation in the Tanan Depression (Tamtsag Basin, Mongolia), which was previously interpreted as a fan-delta depositional system. Based on extensive core investigations, eighteen lithofacies, six lithofacies associations and two genetic deposition systems are identified, and a new sedimentological interpretation is proposed comprising a wave-dominated clastic littoral system in the western half-graben dip slope and a fluvial-dominated fan-delta system in the eastern half-graben. Sediments within the eastern half-graben unit include braidplain, fan-delta front and prodelta environments, while those within the western half-graben dip slope unit comprise dominantly alluvial fan, wave-reworked beach, storm-affected shoreface and offshore sediments. The strikes of the sediments in the western half-graben dip slope unit are parallel to the westward shoreline trend, while the progradation direction of sediments in the eastern half-graben unit is perpendicular to the eastern shoreline. This indicates approximately northwestward-propagating waves that were possibly driven by southeasterly winds, which has implications for understanding the prevailing wind direction in Northeast Asia during the depositional period. Other factors contributing to the preservation of these two distinct sedimentary systems are the paleotopography and subsequent climate shift towards more humid climatic conditions which intensified sediment supply and hydrodynamic conditions that were able to rework the sediments.

Natural soils often exhibit rotated transverse anisotropy due to various geological processes (e.g., tectonic movement, filling and soil deposition), and the trend of soil strength usually changes with depth. This study combines rotated transverse anisotropy with non-stationary random field (RF) to investigate the reliability and failure mechanism of a slope under undrained conditions. Two scenarios of non-stationary RF are considered: (a) the trend of soil strength increases along depth; (b) the trend increases along the direction perpendicular to bedding. It is found that the expected performance levels of slope reliability would be significantly different under different directions of the trend. When the undrained shear strength increases along the direction perpendicular to bedding, the changes of slope reliability and sliding consequence would be sensitive to the dip angle of strata. Besides, the failure mechanism can be affected by the direction of the trend and strata orientation. Generally, shallow failure is more likely to occur on the dip slope when soil strength increases along the direction perpendicular to bedding, while for reverse slope with soil strength increasing perpendicularly to the bedding, deep failure mechanism is significantly dominant.

A natural hillslope developing into a landslide shows ground cracks and topographic deformation. Geomorphological and subsurface investigations using appropriate methodology are essential to understand the failure mechanisms and stability of a hillslope. Huafan University campus located on a dip slope in northern Taiwan is facing a potential landslide hazard. Slope movement was detected through the development of ground cracks and persistent deformation of campus buildings and facilities. To monitor the sliding behavior of the dip slope, a nail network consisting of 144 ground monitoring points was set in 2001, and its coordinates were measured using conventional traverse surveying twice a year until 2017. The 17-year surficial surveying results were presented as a time series of displacements with constraints of geometry and distribution of ground cracks and underground observations. The long-term surveying results reveal multiple potential sliding blocks within the Huafan University campus. A model of landslide movement with a listric sliding surface is proposed. Additionally, from the velocity field derived from the monitoring points, the horizontal strain rates of the slope are estimated. The pattern of strain rates indicates that a plausible fault passing through the campus may have affected the movement of the dip slope. The long-term surface monitoring of a potential landslide slope in this study provides a reliable and economical way to understand the mechanism of movement behavior of the slope and evaluate slope stability.

Large rock avalanches often result in loss of life and catastrophic damage to infrastructure far from their initial failure positions, predominantly due to their tremendous volumes, high velocities and long runouts. Studies of the surface morphologies and internal structures of rock avalanche deposits can reveal evidence of their movement and deposition mechanisms. Through field survey, satellite image interpretation and particle-size distribution analysis, we studied the ancient, long-runout Linka rock avalanche, which is next to the Nujiang River, southeast Tibetan Plateau. The Linka rock avalanche, with a source volume of ~310 Mm3 originated from a high, steep dip slope and then transformed into a channelized rock avalanche, showing high mobility with a superelevation back-calculated maximal velocity of 42 m/s, a travel distance of ~6200 m and a Fahrboschung of 0.24. The slope failure sequence consisted of an initial failure of an outer limestone slab and a second failure of an inner sandstone slab. The limestone avalanche had 2 or 3 surges, while the sandstone avalanche probably had only one surge. The high mobility of the Linka rock avalanche predominantly resulted from a buckling failure occurred on a high relief source, low-energy dissipation during the channelized flow, intensive rock fragmentation in the basal facies and possible water lubrication when propagating bi-directionally along the Waqu River. Our findings for the Linka rock avalanche support previous knowledge that multiple mechanisms have different roles at different stages in a long runout rock avalanche.

Geometry of planner geological structures can interact with topographic slope and cause different types of slope failure (e.g. wedge failure, dip slope failure, and toppling etc.). This study focus on how the tectonic foliation influences the landslide pattern in the southern Central Range of Taiwan. The tectonic foliations in this area range from pencil cleavage to schistosity depending on the increasing of metamorphic grade, and different foliations have different influences on the landslide behaviors. To describe the relation between foliation and topographic slope, we create the θ D value as the angle between the foliation dip direction azimuth and the topographic downslope direction azimuth at a given location. The location of landslides in the area with pencil cleavage has no preferential θ D value, and it suggests the landslide distribution has no correlation with foliation. The location of landslides in the area with well-developed slaty cleavage is mostly in the lower θ D value, which suggests the landslides are more likely located in the area where the foliation dip direction is parallel to the topographic downslope direction. The location of landslide in the area with schistosity is mostly in the high θ D value area, which suggests the landslides are more likely located in the area where the foliation dip direction is opposite to the topographic downslope direction.