Search

Widening the methodology of chromophore analysis in pulp and paper science, a sensitive gas-chromatographic approach with electron-capture detection is presented and applied to model samples and real-world historic paper material. Trifluoroacetic anhydride was used for derivatization of the chromophore target compounds. The derivative formation was confirmed by NMR and accurate mass analysis. The method successfully detects and quantifies hydroxyquinones which are key chromophores in cellulosic matrices. The analytical figures of merit appeared to be in an acceptable range with an LOD down to approx. 60 ng/g for each key chromophore, which allows for their successful detection in historic sample material. [ABSTRACT FROM AUTHOR]

The detection of individual chromophores that contribute to the overall discoloration of paper or pulp (“yellowing”) is a challenge because these substances are only present in extremely small amounts (ppm to ppb range). In this work, paper spray (PS) coupled with mass spectrometry was used to detect a low-concentrated cellulosic key-chromophore, 2,5-dihydroxyacetophenone (DHAP). Sensitivity was enhanced by derivatization with Girard's reagent T (GT). DHAP was successfully detected in historic paper samples and also was applied to model papers in order to investigate different factors that influence its generation: temperature, time, relative humidity, and the presence of iron ions, by means of a full factorial design. The main factors, temperature and relative humidity, have the most impact on the generation of DHAP, but the interactions between the factors are also significant and are therefore important for the degradation process. The historical papers containing DHAP were then compared to the artificially aged samples. The results were confirmed by independent, accurate mass measurements. [ABSTRACT FROM AUTHOR]

A novel approach to measure the degree of acetylation in biopolymers applying a combination of Zemplén-deacetylation by sodium methanolate and GC–MS methodology is introduced. The development focuses on very low limits of detection to cover also samples with extremely low degrees of acetylation which hitherto eluded accurate determination. Free acetic acid or inorganic acetates, often present in biopolymer samples, do not disturb the quantification. Two techniques to measure the Zemplén-released methyl acetate were comparatively assessed, direct injection of the liquid phase and a SPME-based approach, the former being more straightforward, but being inferior to the latter in sensitivity. By applying isotopically labeled methyl acetate released from 4- O -( 13 C 2 -acetyl)-vanillin as the internal standard, influences, such as varying moisture contents, are corrected, improving the overall method reliability to a large extent. The combination of Zemplén-release of acetyl groups in biopolymers as methyl acetate, in connection with its accurate quantification by SPME–GC–MS, was found to be the method of choice for routine, yet very accurate analysis of a wide range of acetylation degrees of biopolymers, showing satisfying analytical parameters along with easy handling and widest applicability. Limit of detection for acetylated cellulose samples is 0.09 nmol/mg, for hemicellulose samples 0.48 nmol/mg. [ABSTRACT FROM AUTHOR]

Abstract: Gas chromatographic analysis of complex carbohydrate mixtures requires highly effective and reliable derivatisation strategies for successful separation, identification, and quantitation of all constituents. Different single-step (per-trimethylsilylation, isopropylidenation) and two-step approaches (ethoximation–trimethylsilylation, ethoximation–trifluoroacetylation, benzoximation–trimethylsilylation, benzoximation–trifluoroacetylation) have been comprehensively studied with regard to chromatographic characteristics, informational value of mass spectra, ease of peak assignment, robustness toward matrix effects, and quantitation using a set of reference compounds that comprise eight monosaccharides (C5–C6), glycolaldehyde, and dihydroxyacetone. It has been shown that isopropylidenation and the two oximation-trifluoroacetylation approaches are least suitable for complex carbohydrate matrices. Whereas the former is limited to compounds that contain vicinal dihydroxy moieties in cis configuration, the latter two methods are sensitive to traces of trifluoroacetic acid which strongly supports decomposition of ketohexoses. It has been demonstrated for two “real” carbohydrate-rich matrices of biological and synthetic origin, respectively, that two-step ethoximation–trimethylsilylation is superior to other approaches due to the low number of peaks obtained per carbohydrate, good peak separation performance, structural information of mass spectra, low limits of detection and quantitation, minor relative standard deviations, and low sensitivity toward matrix effects. [Copyright &y& Elsevier]

Degraded celluloses are becoming increasingly important as part of product streams coming from various biorefinery scenarios. Analysis of the molar mass distribution of such fractions is a challenge, since neither established methods for mono- or disaccharides nor common methods for polysaccharide characterization cover the intermediate oligomer range appropriately. Size exclusion chromatography (SEC) with multi-angle laser light scattering (MALLS), the standard approach for celluloses, suffers from decreased scattering intensities in the lower-molar mass range. The limitation in the low-molecular range can, in principle, be overcome by calibration, but calibration standards for such “short” celluloses are either not readily available or structurally remote and thus questionable. In this paper, we present the calibration of a SEC system— for the first time – with monodisperse cellooligomer standards up to about 3400 g mol −1 . These cellooligomers are “short-chain celluloses” and can be seen as the “true” standard compounds, by contrast to commonly used standards that are chemically different from cellulose, such as pullulan, dextran, polystyrene, or poly(methyl methacrylate). The calibration is compared against those commercial standards and correction factors are calculated. Calibrations with non-cellulose standards can now be adjusted to yield better fitting results, and data already available can be corrected retrospectively. [ABSTRACT FROM AUTHOR]