Search

Abstract Background The Naples Prognostic Score (NPS), integrating inflammatory and nutritional biomarkers, has been reported to be associated with the prognosis of various malignancies, but there is no report on intrahepatic cholangiocarcinoma (ICC). This study aimed to explore the prognostic value of NPS in patients with ICC. Methods Patients with ICC after hepatectomy were collected, and divided into three groups. The prognosis factors were determined by Cox regression analysis. Predictive efficacy was evaluated by the time-dependent receiver operating characteristic (ROC) curves. Results A total of 174 patients were included (Group 1: 33 (19.0%) patients; Group 2: 83 (47.7%) patients; and Group 3: 58 (33.3%) patients). The baseline characteristics showed the higher the NPS, the higher the proportion of patients with cirrhosis and Child-Pugh B, and more advanced tumors. The Kaplan-Meier curves reflect higher NPS were associated with poor survival. Multivariable analysis showed NPS was an independent risk factor of overall survival (NPS group 2 vs. 1: HR = 1.671, 95% CI: 1.022–3.027, p = 0.009; NPS group 3 vs. 1: HR = 2.208, 95% CI: 1.259–4.780, p = 0.007) and recurrence-free survival (NPS group 2 vs. 1: HR = 1.506, 95% CI: 1.184–3.498, p = 0.010; NPS group 3 vs. 1: HR = 2.141, 95% CI: 2.519–4.087, P = 0.001). The time ROC indicated NPS was superior to other models in predicting prognosis. Conclusions NPS is a simple and effective tool for predicting the long-term survival of patients with ICC after hepatectomy. Patients with high NPS require close follow-up, and improving NPS may prolong the survival time.

Abstract Effective thermal management is quite urgent for electronics owing to their ever-growing integration degree, operation frequency and power density, and the main strategy of thermal management is to remove excess energy from electronics to outside by thermal conductive materials. Compared to the conventional thermal management materials, flexible thermally conductive films with high in-plane thermal conductivity, as emerging candidates, have aroused greater interest in the last decade, which show great potential in thermal management applications of next-generation devices. However, a comprehensive review of flexible thermally conductive films is rarely reported. Thus, we review recent advances of both intrinsic polymer films and polymer-based composite films with ultrahigh in-plane thermal conductivity, with deep understandings of heat transfer mechanism, processing methods to enhance thermal conductivity, optimization strategies to reduce interface thermal resistance and their potential applications. Lastly, challenges and opportunities for the future development of flexible thermally conductive films are also discussed.

In order to build green mines, goaf is often filled, supported, and sealed with a high-water material to eliminate a series of environmental problems and safety hazards caused by goaf. In this study, ordinary Portland cement, sulphoaluminate cement, and alkali-activated cement were used as binders to prepare full-tailings high-water materials for filling, with various water-to-cement ratios. The compressive strength development of consolidated tungsten tailings specimens prepared with various curing binders was observed, and the influence of various water–cement ratios on the strength development was analyzed. The environmental impact of mine backfill materials was assessed according to the life cycle theory (LCA), and these mine backfill materials were prepared by using various binders. The results show that when the water-to-binder ratio is 3, the strength of alkali-activated cement can reach 3 MPa at 28 days; at that ratio, the microstructure of alkali-activated cement is more compact. Through LCA analysis, the environmental load of alkali-activated cement is shown to be significantly lower than that of either Portland cement or sulphoaluminate cement; the LCA results show that the primary energy consumption using alkali-activated cement is reduced from the Portland and sulphoaluminate cements by 1319.32 MJ and 945 kg, respectively. These unusual reduction percentages are achieved because the production of alkali-activated cement by LCA does not have any negative environmental impact—the production of alkali-activated cement, with its primary component being industrial byproduct slag, so that the use of alkali-activated cement in tailings’ consolidation has a positive environmental impact.

Low-frequency distributed acoustic sensing (LF-DAS) is a diagnostic tool for hydraulic fracture propagation with far-field monitoring using fiber optic sensors. LF-DAS senses strain rate variation caused by stress field change due to fracture propagation. Fiber optic sensors are installed in the monitoring wells in the vicinity of a fractured well. From the strain responses, fracture propagation can be evaluated. To understand subsurface conditions with multiple propagating fractures, a laboratory-scale hydraulic fracture experiment was performed simulating the LF-DAS response to fracture propagation with embedded distributed optical fiber strain sensors under these conditions. The experiment was performed using a transparent cube of epoxy with two parallel radial initial flaws centered in the cube. Fluid was injected into the sample to generate fractures along the initial flaws. The experiment used distributed high-definition fiber optic strain sensors with tight spatial resolutions. The sensors were embedded at two different locations on opposite sides of the initial flaws, serving as observation/monitoring locations. We also employed finite element modeling to numerically solve the linear elastic equations of equilibrium continuity and stress–strain relationships. The measured strains from the experiment were compared to simulation results from the finite element model. The experimentally derived strain and strain-rate waterfall plots from this study show the responses to both fractures propagating, while the fracture at the lower position took most of the fluid during the experiment. Interestingly, a fracture first began propagating from the upper flaw of the two flaws, but once the lower fracture was initiated, it grew much faster than the upper fracture. Both fibers were intercepted by the lower fracture, further verifying the strain signature as a fracture is approaching and intersecting an offset fiber. [ABSTRACT FROM AUTHOR]