Search

To investigate the seismic behavior of composite columns with high-strength concrete-filled steel tube flanges and honeycomb steel webs (STHHC) after being subjected to freeze-thaw cycles, 36 full-scale STHHCs were designed with the following main parameters: the shear span ratio (λs), the axial compression ratio (n0), the number of freeze-thaw cycles (Nc), the concrete cubic compression strength (fcu), and the steel ratio of the section (αs). Compared with existing experimental data, the validity of the finite element modeling method was verified. Parameter analysis was conducted on 36 full-scale STHHCs to obtain the hysteresis curve of the composite columns and to clarify the impact of the different parameters on the skeleton curve, the energy dissipation capacity, the stiffness degradation, and the ductility of the composite columns. The results showed that the hysteresis curves of all specimens after freeze-thaw cycles exhibited an ideal shuttle shape, reflecting that this kind of composite column has good energy dissipation ability and freeze-thaw resistance. The specimens' maximum bulging deformation and maximum stress both occurred at the column base. Finally, the restoring force model of this kind of composite column is therefore established, and design recommendations based on these results are proposed. [ABSTRACT FROM AUTHOR]

To investigate the axial compression behavior of composite columns with high-strength concrete-filled steel tube flanges and honeycombed steel web (STHHC) under load during freeze–thaw cycles, 48 full-scale composite column specimens were designed with different parameters: the restraint effect coefficient (ξ), concrete strength (fcu), number of freeze–thaw cycles (nd), slenderness ratio (λ), space–height ratio (s/hw), and hole–height ratio (d/hw). The finite element models of STHHC composite columns were simulated using ABAQUS finite element software (Version: 2021). The modeling method's rationality was verified by comparing simulation results with experimental outcomes. Based on the finite element model, a parametric analysis of the composite columns under freeze–thaw cycles was conducted, analyzing their failure modes and load-bearing processes. The results indicate that the bearing capacity of the STHHC increased with increases in ξ and fcu, and decreased with a rise in λ. In contrast, the influence of s/hw and d/hw on the ultimate bearing capacity of the composite columns was relatively minor. An equation for calculating the axial bearing capacity of the STHHC composite columns under freeze–thaw cycles was derived using statistical regression methods and considering the impact of different parameters on the axial compressive performance of the composite columns, laying the foundation for the promotion and application of this type of composite column in practical engineering projects. [ABSTRACT FROM AUTHOR]

To study the eccentric compression mechanical properties of ECC and UHPC filled-in double steel tubular (EUFDST) composite columns, 35 full-scale EUCFDST composite column specimens were designed by ABAQUS software with the slenderness ratio (λ), UHPC cylinder compressive strength (fcu), inner and outer steel tubular strength (fy1, fy2), inner and outer steel tubular thickness (t1, t2), inner and outer steel tubular diameter ratio (Ω), eccentricity (e), and fiber content (γ) as the main parameters. By comparison with the simulation of the existing test, the correctness of the finite element modeling is verified. The parameter analysis of 35 full-scale EUFDST composite columns was carried out to obtain the eccentric load-mid-span deflection curve of the specimens. The failure mechanism, ductility coefficient, and stiffness degradation of the composite columns under different parameters were analyzed, and the section of the composite column was verified to satisfy the plane section assumption. The variation trend of maximum load-bearing capacity and the ductility of composite columns under different parameter conditions was obtained. By introducing the eccentricity correction coefficient and slenderness ratio correction coefficient, the calculation equation of the eccentric maximum load-bearing capacity of EUCFDST composite columns is statistically regressed, which provides a basis for the practical use of these columns. [ABSTRACT FROM AUTHOR]

This study explored the axial compression behavior of elliptical concrete-filled steel tubes with encased steel considering spherical-cap gap (GSECFST) composite short columns. We designed 25 composite column specimens by varying the steel tube yield strength (fty), steel skeleton yield strength (fsy), concrete cubic compression strength (fcu), steel tube thickness (t), steel skeleton sectional area (As), the long and short half-axis ratio (a/b), the gap ratio (Xsg), and the slenderness ratio (λ). Based on the nonlinear constitutive models of the materials and the nonlinear contact effect among materials, the ABAQUS 6.20 finite element software established the refined finite element models of these composite short columns. Also, the rationality of the finite element modeling with a spherical-cap gap was verified by comparing it with the existing experimental results. The influence regularity of various parameters on the load (N)-displacement (Δ) curves, bearing capacity, initial stiffness, and ductility of the composite short columns was obtained. In addition, the failure modes, N-Δ process, sectional strain distribution, and gap feature index of the constraint partition model for GSECFST axial compression short columns were revealed. The results showed a weakened interaction between the elliptical steel tube and concrete. Also, the axial compression bearing capacity, initial stiffness, and core concrete ductility were reduced because of the spherical-cap gap. As fty, fsy, fc, and Asy increased, the axial bearing capacity, initial stiffness, and ductility of GSECFST composite short columns improved significantly but decreased with increasing of a/b, Xsg, and λ. When the gap ratio of the spherical crown was less than 4%, the outer steel tubes in the mid-span area of the GSECFST composite short columns buckled in the direction of the elliptical short axis under axial compression, and the concrete expanded outward and crushed. The failures were similar to those of the specimens without the spherical-cap gap. Based on the sectional constraint partition model, we propose the calculation formula of axial compression bearing capacity for GSECFST composite short columns. Consequently, this study is a reference for the elastic-plastic analysis of frame systems with similar composite columns. [ABSTRACT FROM AUTHOR]

In order to investigate the mechanical behavior of FRP-reactive powder concrete composite tanks with floating tops (FRPCTs) subjected to gravity, twenty-two full-scale FRPCTs were designed with varying parameters for the inner diameter of the storage tank (D) and the thickness of the reactive powder concrete (tc). Based on nonlinear constitutive models and the contact of the materials, and considering tank–liquid coupling, three-dimensional finite element refined models of FRPCTs were established under gravity with ADINA8.5 finite element software, and finite element models of FRPCTs under gravity were verified based on theoretical frequency formulae and existing static tests. Then, the influence of the regularity of different parameters on the equivalent stress, hoop stress, radial stress, and axial stress of the FRPCTs was obtained, and the stress distributions of FRPCTs were clearly described. The results show that the natural frequency of FRPCTs increases gradually with an increase in the height of the tank liquid (Hw); however, the natural frequency of FRPCTs reduces with an increase in D. The equivalent stress, hoop stress, radial stress, and axial stress of the FRP plate and RPC decrease slowly with an increase in tc. The axial stress of the inner RPC increases with an increase in D. The equivalent stress of the inner FRP plate subjected to gravity is distributed in a W shape, the hoop stress, and the axial stress of the FRPCTs are distributed in a U shape, and the radial stress of the inner FRP plate is distributed in an I shape. The maximum displacement occurs in the middle of the FRPCTs, and the bonding between the FRP plate and the concrete is better. Finally, a calculation formula for the variation in the regularity of the tc is developed with different D, and design and construction suggestions for FRPCTs are given, which can provide technical support for the application of the FRPCTs in practical engineering. [ABSTRACT FROM AUTHOR]

The article discusses the accomplishments of the Communist Party of China (CPC) in improving the lives of Chinese citizens and the country's economy in the past 100 years, particularly in establishing a modern socialist country. Also cited are the economic data of China as detailed in the book "Chinese Economic Performance in the Long Run," how the CPC protected the country's sovereignty and national security, and China's market-oriented economic reforms.

In this paper, the cathodic microarc plasma electrolysis (CMPE) was tentatively performed to degrade the phenol in aqueous solution by vapor-gaseous envelope discharge around the Ti cathode. Degradation efficiency of phenol was measured and the intermediate products were evaluated. The suspended particles in solution were analyzed and the decomposition mechanism of phenol in the process of cathodic microarc plasma degradation was discussed. The instantaneous current efficiency reached a peak value firstly and then decreased with the discharge time. In the cathodic plasma region, the Cl substituted the hydrogen on benzene ring in the initial time, which was replaced by a hydroxyl immediately, then the polyhydroxy phenol was easily decomposed. In addition, optical emission spectroscopy was carried out to characterize the plasma features during the CMPE process. The temperature of electron around the microarc discharge envelope reached about 4000 K; thus the phenol was partly carbonized to become graphite particles. CMPE is a promising approach to degrade quickly the phenol in wastewater. [ABSTRACT FROM AUTHOR]