Search

To assess the performance of femoral orthopedic implants, they are often attached to cadaveric femurs, and biomechanical testing is performed. To identify areas of high stress, stress shielding, and to facilitate implant redesign, these tests are often accompanied by finite element (FE) models of the bone/implant system. However, cadaveric bone suffers from wide specimen to specimen variability both in terms of bone geometry, and mechanical properties, making it virtually impossible for experimental results to be reproduced. An alternative approach is to utilize synthetic femurs of standardized geometry, having material behavior approximating that of human bone, but with very. small specimen to specimen variability. This approach allows for repeatable experimental results and a standard geometry for use in accompanying FE models. While the synthetic bones appear to be of appropriate geometry to simulate bone mechanical behavior, it has not, however, been established what bone quality they most resemble, i.e., osteoporotic or osteopenic versus healthy bone. Furthermore, it is also of interest to determine whether FE models of synthetic bones, with appropriate adjustments in input material properties or geometric size, could be used to simulate the mechanical behavior of a wider range of bone quality and size. To shed light on these questions, the axial and torsional stiffness of cadaveric femurs were compared to those measured on synthetic femurs. A FE model previously validated by the authors to represent the geometry of a synthetic femur, was then used with a range of input material properties and change in geometric size, to establish whether cadaveric results could be simulated. Axial and torsional stiffnesses and rigidities were measured for 25 human cadaveric femurs (simulating poor bone stock) and three synthetic 'third generation composite' femurs (3GCF) (simulating normal healthy bone stock) in the midstance orientation. The measured results were compared, under identical loading conditions, to those predicted by a previously validated three-dimensional finite element model of the 3GCF at a variety of Young's modulus values. A smaller FE model of the 3GCF was also created to examine the effects of a simple change in bone size. The 3GCF was found to be significantly stiffer (2.3 times in torsional loading, 1.7 times in axial loading) than the presently utilized cadaveric samples. Nevertheless, the FE model was able to successfully simulate both the behavior of the 3GCF, and a wide range of cadaveric bone data scatter by an appropriate adjustment of Young's modulus or geometric size. The synthetic femur had a significantly higher stiffness than the cadaveric bone samples. The finite element model provided a good estimate of upper and lower bounds for the axial and torsional stiffness of human femurs because it was effective at reproducing the geometric properties of a femur Cadaveric bone experiments can be used to calibrate FE models' input material properties so that bones of varying quality can be simulated. [DOI: 10.1115/1.2401178] Keywords: biomechanics, finite element analysis, cadaveric femur, torsional stiffness, axial stiffness

This study proposes a novel hybrid total knee replacement (TKR) design to improve stress transfer to bone in the distal femur and, thereby, reduce stress shielding and consequent bone loss. Three-dimensional finite element (FE) models were developed for a standard and a hybrid TKR and validated experimentally. The Duracon knee system (Stryker Canada) was the standard TKR used for the FE models and for the experimental tests. The FE hybrid device was identical to the standard TKR, except that it had an interposing layer of carbon fibre-reinforced polyamide 12 lining the back of the metallic femoral component. A series of experimental surface strain measurements were then taken to validate the FE model of the standard TKR at 3000 N of axial compression and at 0 degreeof knee flexion. Comparison of surface strain values from FE analysis with experiments demonstrated good agreement, yielding a high Pearson correlation coefficient of R(2)= 0.94. Under a 3000N axial load and knee flexion angles simulating full stance (0O degree, heel strike (200 degrees, and toe off (600 degrees during normal walking gait, the FE model showed considerable changes in maximum Von Mises stress in the region most susceptible to stress shielding (i.e. the anterior region, just behind the flange of the femoral implant). Specifically, going from a standard to a hybrid TKR caused an increase in maximum stress of 87.4 per cent (O0 degree from 0.15 to 0.28 MPa), 68.3 per cent (200 degrees from 1.02 to 1.71 MPa), and 12.6 per cent (600 degrees from 2.96 to 3.33 MPa). This can potentially decrease stress shielding and subsequent bone loss and knee implant loosening. This is the first report to propose and biomechanically to assess a novel hybrid TKR design that uses a layer of carbon fibrereinforced polyamide 12 to reduce stress shielding. [ABSTRACT FROM AUTHOR]

Biomechanical studies on femur fracture fixation with orthopaedic implants are numerous in the literature. However, few studies have compared the mechanical stability of these repair constructs in osteoporotic versus normal bone. The present aim was to examine how changes in cortical wall thickness of intact femurs affect biomechanical characteristics. A three-dimensional, linear, isotropic finite element (FE) model of an intact femur was developed in order to predict the effect of bicortical wall thickness, t, relative to the femur's mid-diaphyseal outer diameter, D, over a cortex thickness ratio range of 0 < or = t/D < or = 1. The FE model was subjected to loads to obtain axial, lateral, and torsional stiffness. Ten commercially available synthetic femurs were then used to mimic 'osteoporotic' bone with t/D = 0.33, while ten synthetic left femurs were used to simulate 'normal' bone with t/D = 0.66. Axial, lateral, and torsional stiffness were measured for all femurs. There was excellent agreement between FE analysis and experimental stiffness data for all loading modes with an aggregate average percentage difference of 8 per cent. The FE results for mechanical stiffness versus cortical thickness ratio (0 < or = t/D < or = 1) demonstrated exponential trends with the following stiffness ranges: axial stiffness (0 to 2343 N/mm), lateral stiffness (0 to 62 N/mm), and torsional stiffness (0 to 198 N/mm). This is the first study to characterize mechanical stiffness over a wide range of cortical thickness values. These results may have some clinical implications with respect to appropriately differentiating between older and younger human long bones from a mechanical standpoint. [ABSTRACT FROM AUTHOR]

Biomechanical investigations are increasingly using commercially available synthetic femurs as surrogates for human cadaveric femurs. However, the rate of force application in testing these artificial femurs appears to be chosen arbitrarily without much consideration to their visco-elastic time-dependent nature. The aim of this study, therefore, was to examine the effect of loading rate on the mechanical behaviour of synthetic femurs. Ten left, medium, fourth-generation composite femurs (Model 3403, Pacific Research Laboratories, Vashon, WA, USA) were fixed distally into cement-filled steel cubic chambers for mounting into a mechanical tester. In randomized order, each of the ten femurs was loaded at rates of 1, 2.5, 5, 7.5, 10, 20, 30, 40, 50, and 60 mm/min to obtain axial, lateral, and torsional stiffness. Axial stiffness showed an aggregate average value of 1742.7 +/- 174.7 N/mm with a high linear correlation with loading rate (R2 = 0.80). Lateral stiffness yielded an aggregate average value of 56.9 +/- 10.2 N/mm and was linearly correlated with loading rate (R2 = 0.85). Torsional stiffness demonstrated an aggregate average value of 176.9 +/- 14.5 N/mm with a strong linear correlation with loading rate (R2 = 0.59). Despite the high correlations between stiffness and speed, practically this resulted in an overall average difference between the lowest and highest stiffness of only 4 per cent. Moreover, no statistical comparisons between loading rates for axial, lateral, or torsional test modes showed differences (p > or = 0.843). Future biomechanical investigators utilizing these synthetic femurs need not be concerned with loading rate effects over the range tested presently. This is the first study in the literature to perform such an assessment. [ABSTRACT FROM AUTHOR]

Biomechanical assessments of orthopaedic fracture fixation constructs are increasingly using commercially available analogues such as the fourth-generation composite femur (4GCF). The aim of this study was to compare cancellous screw purchase directly between these surrogates and human femurs, which has not been done previously. Synthetic and human femurs each had one orthopaedic cancellous screw (major diameter, 6.5 mm) inserted along the femoral neck axis and into the spongy bone of the femoral head to a depth of 30 mm. Screws were removed to obtain pull-out force, shear stress, and energy values. The three experimental study groups (n = 6 femurs each) were the 4GCF with a 'solid' cancellous matrix, the 4GCF with a 'cellular' cancellous matrix, and human femurs. Moreover, a finite element model was developed on the basis of the material properties and anatomical geometry of the two synthetic femurs in order to assess cancellous screw purchase. The results for force, shear stress, and energy respectively were as follows: 4GCF solid femurs, 926.47 +/- 66.76 N, 2.84 +/- 0.20 MPa, and 0.57 +/- 0.04 J; 4GCF cellular femurs, 1409.64 +/- 133.36 N, 4.31 +/- 0.41 MPa, and 0.99 +/- 0.13 J; human femurs, 1523.29 +/- 1380.15N, 4.66 +/- 4.22 MPa, and 2.78 +/- 3.61J. No statistical differences were noted when comparing the three experimental groups for pull-out force (p = 0.413), shear stress (p = 0.412), or energy (p = 0.185). The 4GCF with either a 'solid' or 'cellular' cancellous matrix is a good biomechanical analogue to the human femur at the screw thread-bone interface. This is the first study to perform a three-way investigation of cancellous screw purchase using 4GCFs, human femurs, and finite element analysis. [ABSTRACT FROM AUTHOR]

The mechanical behaviour of human scapholunate ligaments is not well described in the literature with regard to torsion. In this study, intact scapholunate specimens were mechanically tested in torsion to determine whether a simultaneous tensile load was generated. Human intact scapholunate specimens (n = 19) were harvested. The scaphoid and lunate bones were potted in square chambers using epoxy cement, while the interposing ligament remained exposed. Each specimen was mounted rigidly in a specially designed test jig and remained at a fixed axial length during all tests. Specimens were subjected to a torsional load regime that included cyclic preconditioning, ramp-up, stress relaxation, ramp-down, rest, and torsion to failure. Torque and axial tension were monitored simultaneously. The relationship between torsion and tension was determined. Graphs of torque versus tension were generated, from which outcome measures were extracted. Tests demonstrated a clear relationship between applied torsion and the resulting generation of tension for the ligament during ramp-up (torsion-to-tension ratio, 38.86 +/- 29.00 mm; linearity coefficient R2 = 0.89 +/- 0.15; n = 19), stress relaxation (torsion-to-tension ratio, 23.43 +/- 15.84 mm; R2 = 0.90 +/- 0.09; n = 16), and failure tests (torsion-to-tension ratio, 38.81 +/- 26.39mm; R2 = 0.77 +/- 0.20; n = 16). No statistically significant differences were detected between the torsion-to-tension ratios (p = 0.13) or between the linearity (R2) of the best-fit lines (p > 0.085). A strongly coupled linear relationship between torsion and tension for the scapholunate ligament was exhibited in all test phases. This may suggest interplay between these two parameters in the stabilization of the ligament during normal motion and for injury cascades. [ABSTRACT FROM AUTHOR]

Orthopaedic fracture fixation constructs are typically mounted on to human long bones using cortical screws. Biomechanical studies are increasingly employing commercially available synthetic bones. The aim of this investigation was to examine the effect of the screw pull-out rate and canal reaming on the cortical bone screw purchase strength in synthetic bone. Cylinders made of synthetic material were used to simulate unreamed (foam-filled) and reamed (hollow) human long bone with an outer diameter of 35&VeryThinSpace;mm and a cortex wall thickness of 4&VeryThinSpace;mm. The unreamed and reamed cylinders each had 56 sites along their lengths into which orthopaedic cortical bone screws (major diameter, 3.5&VeryThinSpace;mm) were inserted to engage both cortices. The 16 test groups (n&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;7 screw sites per group) had screws extracted at rates of 1&VeryThinSpace;mm/min, 5&VeryThinSpace;mm/min, 10&VeryThinSpace;mm/min, 20&VeryThinSpace;mm/min, 30&VeryThinSpace;mm/min, 40&VeryThinSpace;mm/min, 50&VeryThinSpace;mm/min, and 60&VeryThinSpace;mm/min. The failure force and failure stress increased and were highly linearly correlated with pull-out rate for reamed (R2&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.60 and 0.60), but not for unreamed (R2&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.00 and 0.00) specimens. The failure displacement and failure energy were relatively unchanged with pull-out rate, yielding low coefficients for unreamed (R2&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.25 and 0.00) and reamed (R2&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.27 and 0.00) groups. Unreamed versus reamed specimens were statistically different for failure force (p&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.000) and stress (p&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.000), but not for failure displacement (p&VeryThinSpace;&VeryThinSpace;=&VeryThinSpace;&VeryThinSpace;0.297) and energy (0.054&VeryThinSpace;<&VeryThinSpace;p&VeryThinSpace;<&VeryThinSpace;1.000). This is the first study to perform an extensive investigation of the screw pull-out rate in unreamed and reamed synthetic long bone. [ABSTRACT FROM AUTHOR]

Intramedullary nails are commonly used to repair femoral fractures. Fractures in normal healthy bone often occur in the young during motor vehicle accidents. Although clinically beneficial, bone refracture and implant failure persist. Large variations in human femur quality and geometry have motivated recent experimental use of synthetic femurs that mimic human tissue and the development of increasingly sophisticated theoretical models. Four synthetic femurs were fitted with a T2 femoral nailing system (Stryker, Mahwah, New Jersey, USA). The femurs were not fractured in order to simulate post-operative perfect union. Six configurations were created: retrograde nail with standard locking (RS), retrograde nail with advanced locking 'off' (RA-off), retrograde nail with advanced locking 'on' (RA-on), antegrade nail with standard locking (AS), antegrade nail with advanced locking 'off' (AA-off), and antegrade nail with advanced locking 'on' (AA-on). Strain gauges were placed on the medial side of femurs. A 580N axial load was applied, and the stiffness was measured. Strains were recorded and compared with results from a three-dimensional finite element (FE) model. Experimental axial stiffnesses for RA-off (771.3 N/mm) and RA-on (681.7 N/mm) were similar to intact human cadaveric femurs from previous literature (757±264N/mm). Conversely, experimental axial stiffnesses for AS (1168.8N/mm), AA-off (1135.3 N/mm), AA-on (1152.1 N/mm), and RS (1294.0 N/mm) were similar to intact synthetic femurs from previous literature (1290±30N/mm). There was better agreement between experimental and FE analysis strains for RS (average percentage difference, 11.6 per cent), RA-on (average percentage difference, 11.1 per cent), AA-off (average percentage difference, 13.4 per cent), and AA-on (average percentage difference, 16.0 per cent), than for RA-off (average percentage difference, 33.5 per cent) and AS (average percentage difference, 32.6 per cent). FE analysis was more predictive of strains in the proximal and middle sections of the femur-nail construct than the distal. The results mimicked post-operative clinical stability at low static axial loads once fracture healing begins to occur. [ABSTRACT FROM AUTHOR]

Abstract Background Management of tibial fractures associated with soft tissue injury remains controversial. Previous studies have assessed perfusion of the fractured tibia and surrounding soft tissues in the setting of a normal soft tissue envelope. The purpose of this study was to determine the effects of muscle contusion on blood flow to the tibial cortex and muscle during reamed, intramedullary nailing of a tibial fracture. Methods Eleven adult canines were distributed into two groups, Contusion or No-Contusion. The left tibia of each canine underwent segmental osteotomy followed by limited reaming and locked intramedullary nailing. Six of the 11 canines had the anterior muscle compartment contused in a standardized fashion. Laser doppler flowmetry was used to measure cortical bone and muscle perfusion during the index procedure and at 11 weeks post-operatively. Results Following a standardized contusion, muscle perfusion in the Contusion group was higher compared to the No-Contusion group at post-osteotomy and post-reaming (p < 0.05). Bone perfusion decreased to a larger extent in the Contusion group compared to the No-Contusion group following osteotomy (p < 0.05), and the difference in bone perfusion between the two groups remained significant throughout the entire procedure (p < 0.05). At 11 weeks, muscle perfusion was similar in both groups (p > 0.05). There was a sustained decrease in overall bone perfusion in the Contusion group at 11 weeks, compared to the No-Contusion group (p < 0.05). Conclusions Injury to the soft tissue envelope may have some deleterious effects on intraosseous circulation. This could have some influence on the fixation method for tibia fractures linked with significant soft tissue injury.

Abstract Background A variety of techniques are available for fixation of femoral shaft fractures following total hip arthroplasty. The optimal surgical repair method still remains a point of controversy in the literature. However, few studies have quantified the performance of such repair constructs. This study biomechanically examined 3 different screw-plate and cable-plate systems for fixation of periprosthetic femoral fractures near the tip of a total hip arthroplasty. Methods Twelve pairs of human cadaveric femurs were utilized. Each left femur was prepared for the cemented insertion of the femoral component of a total hip implant. Femoral fractures were created in the femurs and subsequently repaired with Construct A (Zimmer Cable Ready System), Construct B (AO Cable-Plate System), or Construct C (Dall-Miles Cable Grip System). Right femora served as matched intact controls. Axial, torsional, and four-point bending tests were performed to obtain stiffness values. Results All repair systems showed 3.08 to 5.33 times greater axial stiffness over intact control specimens. Four-point normalized bending (0.69 to 0.85) and normalized torsional (0.55 to 0.69) stiffnesses were lower than intact controls for most comparisons. Screw-plates provided either greater or equal stiffness compared to cable-plates in almost all cases. There were no statistical differences between plating systems A, B, or C when compared to each other (p > 0.05). Conclusions Screw-plate systems provide more optimal mechanical stability than cable-plate systems for periprosthetic femur fractures near the tip of a total hip arthroplasty.

Abstract Background The bone loss associated with revision surgery or pathology has been the impetus for developing modular revision total hip prostheses. Few studies have assessed these modular implants quantitatively from a mechanical standpoint. Methods Three-dimensional finite element (FE) models were developed to mimic a hip implant alone (Construct A) and a hip implant-femur configuration (Construct B). Bonded contact was assumed for all interfaces to simulate long-term bony ongrowth and stability. The hip implants modeled were a Modular stem having two interlocking parts (Zimmer Modular Revision Hip System, Zimmer, Warsaw, IN, USA) and a Monoblock stem made from a single piece of material (Stryker Restoration HA Hip System, Stryker, Mahwah, NJ, USA). Axial loads of 700 and 2000 N were applied to Construct A and 2000 N to Construct B models. Stiffness, strain, and stress were computed. Mechanical tests using axial loads were used for Construct A to validate the FE model. Strain gages were placed along the medial and lateral side of the hip implants at 8 locations to measure axial strain distribution. Results There was approximately a 3% average difference between FE and experimental strains for Construct A at all locations for the Modular implant and in the proximal region for the Monoblock implant. FE results for Construct B showed that both implants carried the majority (Modular, 76%; Monoblock, 66%) of the 2000 N load relative to the femur. FE analysis and experiments demonstrated that the Modular implant was 3 to 4.5 times mechanically stiffer than the Monoblock due primarily to geometric differences. Conclusions This study provides mechanical characteristics of revision hip implants at sub-clinical axial loads as an initial predictor of potential failure.

Comminuted proximal humerus fractures are often repaired by metal plates, but potentially still experience bone refracture, bone "stress shielding," screw perforation, delayed healing, and so forth. This "proof of principle" investigation is the initial step towards the design of a new plate using alternative materials to address some of these problems. Finite element modeling was used to create design graphs for bone stress, plate stress, screw stress, and interfragmentary motion via three different fixations (no, 1, or 2 "kickstand" [KS] screws across the fracture) using a wide range of plate elastic moduli (E P  = 5-200 GPa). Well-known design optimization criteria were used that could minimize bone, plate, and screw failure (i.e., peak stress < ultimate tensile strength), reduce bone "stress shielding" (i.e., bone stress under the new plate ≥ bone stress for an intact humerus, titanium plate, and/or steel plate "control"), and encourage callus growth leading to early healing (i.e., 0.2 mm ≤ axial interfragmentary motion ≤ 1 mm; shear/axial interfragmentary motion ratio <1.6). The findings suggest that a potentially optimal configuration involves the new plate being manufactured from a material with an E P of 5-41.5 GPa with 1 KS screw; but, using no KS screws would cause immediate bone fracture and 2 KS screws would almost certainly lead to delayed healing. A prototype plate might be fabricated using alternative materials suggested for orthopedics and other industries, like fiber-metal laminates, fiber-reinforced polymers, metal foams, pure polymers, shape memory alloys, or 3D-printed porous metals., (© 2024 John Wiley & Sons Ltd.)

Bone fracture plates are usually made from titanium alloy or stainless steel, which are much stiffer than bone. However, overly stiff plates can restrict axial interfragmentary motion at the fracture leading to delayed callus formation and healing, as well as causing bone "stress shielding" under the plate leading to bone atrophy, bone resorption, and plate loosening. Consequently, there have been many prior efforts to develop nonmetallic bone fracture plates with customized material properties using synthetic fibers (e.g., aramid, carbon, glass) in polymer resin. Even so, plant fibers (e.g., flax, roselle, sisal) offer additional advantages over synthetic fibers, such as availability, biodegradability, less toxicity during processing, lower financial cost, and recyclability. As such, there is an emerging interest in using plant fibers alone, or combined with synthetic fibers, to reinforce polymers for various applications. Thus, this is the first review article on the material properties and engineering performance of innovative bone fracture plates made from composite materials reinforced by plant fibers alone or supplemented using synthetic fibers. This article presents material-level fiber properties (e.g., elastic modulus, ultimate strength), material-level plate properties (e.g., fatigue strength, impact toughness), and bone-plate engineering performance (e.g., overall stiffness, plate stress), as well as discussing general findings, study quality, and future work. This article may help engineers and surgeons to design, fabricate, analyze, and utilize novel bone fracture plates.

Background: This study experimentally validated a computationally optimized screw number and screw distribution far cortical locking distal femur fracture plate and compared the results to traditional implants., Methods: 24 artificial femurs were osteotomized with a 10 mm fracture gap 60 mm proximal to the intercondylar notch. Three fixation constructs were used. (i) Standard locking plates secured with three far cortical locking screws inserted according to a previously optimized distribution in the femur shaft (n = 8). (ii) Standard locking plates secured with four standard locking screws inserted in alternating plate holes in the femur shaft (n = 8). (iii) Retrograde intramedullary nail secured proximally with one anterior-posterior screw and distally with two oblique screws (n = 8). Axial hip forces (700 and 2800 N) were applied while measuring axial interfragmentary motion, shear interfragmentary motion, and overall stiffness., Findings: Experimental far cortical locking plate results compared well to published computational findings. Far cortical locking femurs contained the highest axial motion within the potential ideal range of 0.2-1 mm and a sheer-to-axial motion ratio < 1.6 at toe-touch weight-bearing (700 N). At full weight-bearing (2800 N), Standard locking-plated femurs had the only axial motion within 0.2-1 mm but had an excess shear-to-axial motion ratio. Nail-implanted femurs underperformed at both forces., Interpretation: For toe-touch weight-bearing, the far cortical locking construct provided optimal biomechanics to allow moderate motion, which has been suggested to encourage early callus formation. Conversely, at full weight-bearing, the standard locking construct offered the biomechanical advantage on fracture motion., Competing Interests: Declaration of competing interest Emil H. Schemitsch previously received personal fees and research support from Zimmer Biomet. Radovan Zdero previously received “in kind” research support from Zimmer Biomet. No conflicts exist for the other authors., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The goal of this article was to review studies on distal humerus fracture plates (DHFPs) to understand the biomechanical influence of systematically changing the plate or screw variables. The problem is that DHFPs are commonly used surgically, although complications can still occur, and it is unclear if implant configurations are always optimized using biomechanical criteria. A systematic search of the PubMed database was conducted to identify English-language biomechanical optimization studies of DHFPs that parametrically altered plate and/or screw variables to analyze their influence on engineering performance. Intraarticular and extraarticular fracture (EAF) data were separated and organized under commonly used biomechanical outcome metrics. The results identified 52 eligible DHFP studies, which evaluated various plate and screw variables. The most common plate variables evaluated were geometry, hole type, number, and position. Fewer studies assessed screw variables, with number and angle being the most common. However, no studies examined nonmetallic materials for plates or screws, which may be of interest in future research. Also, articles used various combinations of biomechanical outcome metrics, such as interfragmentary fracture motion, bone, plate, or screw stress, number of loading cycles to failure, and overall stiffness (Os) or failure strength (Fs). However, no study evaluated the bone stress under the plate to examine bone "stress shielding," which may impact bone health clinically. Surgeons treating intraarticular and extraarticular distal humerus fractures should seriously consider two precontoured, long, thick, locked, and parallel plates that are secured by long, thick, and plate-to-plate screws that are located at staggered levels along the proximal parts of the plates, as well as an extra transfracture plate screw. Also, research engineers could improve new studies by perusing recommendations in future work (e.g., studying alternative nonmetallic materials or "stress shielding"), clinical ramifications (e.g., benefits of locked plates), and study quality (e.g., experimental validation of computational studies)., Competing Interests: The authors declare no conflicts of interest., (Copyright © 2024 Radovan Zdero et al.)

Study Design: In-vitro cadaveric biomechanical study., Objectives: Long posterior spinal fusion is a standard treatment for adult spinal deformity. However, these rigid constructs are known to alter motion and stress to the adjacent non-instrumented vertebrae, increasing the risk of proximal junctional kyphosis (PJK). This study aimed to biomechanically compare a standard rigid construct vs constructs "topped off" with a semi-rigid construct. By understanding semi-rigid constructs' effect on motion and overall construct stiffness, surgeons and researchers could better optimize fusion constructs to potentially decrease the risk of PJK and the need for revision surgery., Methods: Nine human cadaveric spines (T1-T12) underwent non-destructive biomechanical range of motion tests in pure bending or torsion and were instrumented with an all-pedicle-screw (APS) construct from T6-T9. The specimens were sequentially instrumented with semi-rigid constructs at T5: (i) APS plus sublaminar bands; (ii) APS plus supralaminar hooks; (iii) APS plus transverse process hooks; and (iv) APS plus short pedicle screws., Results: APS plus transverse process hooks had a range of motion (ie, relative angle) for T4-T5 and T5-T6, as well as an overall mechanical stiffness for T1-T12, that was more favourable, as it reduced motion at adjacent levels without a stark increase in stiffness. Moreover, APS plus transverse process hooks had the most linear change for range of motion across the entire T3-T7 range., Conclusions: Present findings suggest that APS plus transverse process hooks has a favourable biomechanical effect that may reduce PJK for long spinal fusions compared to the other constructs examined., Competing Interests: Declaration of Conflicting InterestsThe author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article.