Search

Lithium–sulfur batteries (LSBs) have emerged as promising power sources for high‐performance devices such as electric vehicles. However, the poor energy density of LSBs owing to polysulfide shuttling and passivation has limited their further market penetration. To mitigate this challenge, two‐dimensional (2D) siloxene (2DSi), a Si‐based analog of graphene, is utilized as an additive for sulfur cathodes. The 2DSi is fabricated on a large scale by simple solvent extraction of calcium disilicide to form a thin‐layered structure of Si planes functionalized with vertically aligned hydroxyl groups in the 2DSi. The stoichiometric reaction of 2DSi with polysulfides generates a thiosulfate redox mediator, secures the intercalation pathway, and reveals Lewis acidic sites within the siloxene galleries. The 2DSi utilizes the corresponding in‐situ‐formed electrocatalyst, the 2D confinement effect of the layered structure, and the surface affinity based on Lewis acid–base interaction to improve the energy density of 2DSi‐based LSB cells. Combined with the commercial carbon‐based current collector, 2DSi‐based LSB cells achieve a volumetric energy density of 612 Wh Lcell−1 at 1 mA cm−2 with minor degradation of 0.17% per cycle, which rivals those of state‐of‐the‐art LSBs. This study presents a method for the industrial production of high‐energy‐dense LSBs.

The development of sulfur cathodes with high areal capacity and high energy density is crucial for the practical application of lithium–sulfur batteries (LSBs). LSBs can be built by employing (ultra) high‐loading sulfur cathodes, which have rarely been realized due to massive passivation and shuttling. Herein, microspheres of a carbon–carbon nitride composite (C@CN) with large mesopores are fabricated via molecular cooperative assembly. Using the C@CN‐based electrodes, the effects of the large mesopores and N‐functional groups on the electrochemical behavior of sulfur in LSB cells are thoroughly investigated under ultrahigh sulfur‐loading conditions (>15 mgS cm−2). Furthermore, for high‐energy‐density LSBs, the C@CN powders are pelletized into a thick free‐standing electrode (thickness: 500 μm; diameter: 11 mm) via a simple briquette process; here, the total amount of energy stored by the LSB cells is 39 mWh, corresponding to a volumetric energy density of 440 Wh L−1 with an areal capacity of 24.9 and 17.5 mAh cm−2 at 0.47 and 4.7 mA cm−2, respectively (at 24 mgS cm−2). These results have significantly surpassed most recent records due to the synergy among the large mesopores, (poly)sulfide‐philic surfaces, and thick electrodes. The developed strategy with its potential for scale‐up successfully fills the gap between laboratory‐scale cells and practical cells without sacrificing the high areal capacity and high energy density, providing a solid foundation for the development of practical LSBs.

This work was financially supported by and Chonnam National University, 2016 and the RD No. 2019R1C1C1007745, the National Research Foundation of Korea (NRF) grant funded by the Korea government (Ministry of Science, ICT & Future Planning; No. 2019R1A4A2001527).

Solar-energy-driven water purification is a promising technology for obtaining clean water during the current global climate crisis. Solar absorbers with high light absorption capacity and efficient energy conversion are critical components of solar-driven water evaporation and purification systems. Herein, we demonstrate that porous reduced graphene oxide (rGO)-based composite spheres facilitate efficient water evaporation and effective organic pollutant adsorption from water. Most solar light (>99% for 1 mm thick composites) is absorbed by the porous rGO-based composite spheres floating on water and is subsequently converted into heat, which is efficiently transferred to water at the air-water interface. Evaporation efficiency via energy conversion by the floating sphere composites reaches ∼74%. The increase in surface temperature of water also contributes to improving the adsorption capacity of the rGO-based composite spheres for organic pollutants. Furthermore, the composites can effectively block ultraviolet radiation, preventing the chemical reaction of water pollutants into harmful components.

The fluids of fascinating nanomaterials have recently been reported to exhibit liquid crystalline (LC) phases, and these mesophases have attracted significant interest in both fluid physics and cutting-edge applications; graphitic carbon nitride (g-CN), a type of 2D semiconducting polymers, has gained significant attention in recent years for optoelectronic and catalytic applications. However, g-CN has been studied on a powder material, which suffers from limited dispersibility, difficult recovery, and low surface accessibility. In this study, we report that controlled g-CN, which has high-aspect ratio and expanded interlayer spacing, can exhibit its true LC phase in concentrated sulfuric acid. By utilizing its LC phase, more importantly, we could fabricate a g-CN fiber for the first time.

The lithium-polysulfide (LiPS) dissolution from the cathode to the organic electrolyte is the main challenge for high-energy-density lithium-sulfur batteries (LSBs). Herein, we present a multi-functional porous carbon, melamine cyanurate (MCA)-glucose-derived carbon (MGC), with superior porosity, electrical conductivity, and polysulfide affinity as an efficient sulfur support to mitigate the shuttle effect. MGC is prepared via a reactive templating approach, wherein the organic MCA crystals are utilized as the pore-/micro-structure-directing agent and nitrogen source. The homogeneous coating of spherical MCA crystal particles with glucose followed by carbonization at 600 °C leads to the formation of hierarchical porous hollow carbon spheres with abundant pyridinic N-functional groups without losing their microstructural ordering. Moreover, MGC enables facile penetration and intensive anchoring of LiPS, especially under high loading sulfur conditions. Consequently, the MGC cathode exhibited a high areal capacity of 5.79 mAh cm−2 at 1 mA cm−2 and high loading sulfur of 6.0 mg cm−2 with a minor capacity decay rate of 0.18% per cycle for 100 cycles.

In this study, anatase titania was utilized to prepare a durable photocatalytic paint with substantially enhanced photoactivity towards NO oxidation. Consequently, to alleviate the choking effect of photocatalytic paint and incorporate self-cleaning properties, the parent anatase titania was modified with Al(OH)3 and a number of organosilane (tetraethyl orthosilicate, propyltrimethoxysilane, triethoxy(octadecyl)silane, and trimethylchlorosilane) coatings. A facile hydrolysis approach in ethanol was employed to coat the parent titania. To facilitate uniform dispersion in photocatalytic paint and strong bonding with the prevailing organic matrix, it is necessary to avail both hydrophobic and hydrophilic regions on the titania surface. Therefore, during the preparation of modified titania, the weight proportion of the total weight of alkyl silane and trimethylchlorosilane was adjusted to a ratio of 1:1. As the parent titania has few hydrophilic portions on the surface, tetraethyl orthosilicate was coated with an organic silane having an extended alkyl group as a hydrophobic group and tetraethyl orthosilicate as a hydrophilic group. When these two silane mixtures are hydrolyzed simultaneously and coated on the surface of parent titania, a portion containing a large amount of tetraethyl orthosilicate becomes hydrophilic, and a part containing an alkyl silane becomes hydrophobic. The surface morphology and the modified titania’s optical attributes were assessed using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), UV-Vis diffuse reflectance spectroscopy (DRS), and electrochemical impedance spectroscopy (EIS) analysis. Based on the advanced characterizations, the NO removal mechanism of the modified titania is reported. The modified titania coated at 20 wt.% on the ceramic substrate was found to remove ~18% of NO under one h of UV irradiation. An extensive UV durability test was also carried out, whereby the coated surface with modified titania was exposed to 350 W/m2 of UV irradiance for 2 weeks. The results indicated that the coated surface appeared to preserve the self-cleaning property even after oil spraying. Hence, facile hydrolysis of multiple organosilane in ethanol could be a viable approach to design the coating on anatase titania for the fabrication of durable photoactive paint.

Modifying the physical, chemical structures of graphitic carbon nitride (g-CN) to improve its optoelectronic properties is the most efficient way to meet a high photoactivity for clean and sustainable energy production. Herein, a higher monomeric precursor for synthesizing improved micro-and electronic structure possessing g-CN was prepared by high-concentrated sulfuric acid (SA) treatment of bulk type g-CN (BCN). Several structural analyses show that after the SA treatment of BCN, the polymeric melon-based structure is torn down to cyameluric or cyanuric acid-based material. After re-polycondensation of this material as a precursor, the resulting g-CN has more condensed microstructure, carbon and oxygen contents than BCN, indicating that C, O co-doping by corrosive acid of SA. This g-CN shows a much better visible light absorption and diminished radiative charge recombination by the charge localization effect induced by heteroatoms. As a result, this condensed C, O co-doped g-CN shows the enhanced photocatalytic hydrogen evolution rate of 4.57 µmol/h from water under the visible light (>420 nm) by almost two times higher than that of BCN (2.37 µmol/h). This study highlights the enhanced photocatalytic water splitting performance as well as the provision of the higher monomeric precursor for improved g-CN.

Large particulate photocatalysts allow efficient recovery or installation into the substrate, while limiting possible light-catalyst interaction or mass/charge-transfer. In this study, we developed monodisperse organic single-crystal monoliths with controllable dimensions in the range of 10–100 μm. These were prepared on a 10-g scale by a solution-processed molecular cooperative assembly between melamine (M) and trithiocyanuric acid (TCA) and then transformed into the corresponding g-CN (MTCA-CN) by thermal polycondensation. Molecular precursors that are tightly bound in the crystal undergo polycondensation without losing their macroscopic properties depending on the dimensions of MTCA, thereby changing the microstructure, electronic structure, and photocatalytic activity. Such dimensional tunability enables the fulfillment of various catalytic requirements such as particle size, light absorption, charge separation, band edge potential, and mass transfer. As a proof-of-concept, it was shown that MTCA-CN is tailored to have a high rate of evolution of hydrogen (3.19 μmol/h) from glucose via photoreforming under AM1.5G by using MTCA-100 crystals, leading to the formation of g-CN with the more positive highest occupied molecular orbital (HOMO) level. This study highlights the possibility of developing photocatalysts for practical use and obtaining value-added products (VAPs) without losing the photocatalytic activity relevant for wastewater treatment.

Rechargeable lithium&ndash, sulfur batteries (LSBs) are emerging as some of the most promising next-generation battery alternatives to state-of-the-art lithium-ion batteries (LIBs) due to their high gravimetric energy density, being inexpensive, and having an abundance of elemental sulfur (S8). However, one main, well-known drawback of LSBs is the so-called polysulfide shuttling, where the polysulfide dissolves into organic electrolytes from sulfur host materials. Numerous studies have shown the ability of porous carbon as a sulfur host material. Porous carbon can significantly impede polysulfide shuttling and mitigate the insulating passivation layers, such as Li2S, owing to its intrinsic high electrical conductivity. This work suggests a scalable and straightforward one-step synthesis method to prepare a unique interconnected microporous and mesoporous carbon framework via salt templating with a eutectic mixture of LiI and KI at 800 &deg, C in an inert atmosphere. The synthesis step used environmentally friendly water as a washing solvent to remove salt from the carbon&ndash, salt mixture. When employed as a sulfur host material, the electrode exhibited an excellent capacity of 780 mAh g&minus, 1 at 500 mA g&minus, 1 and a sulfur loading mass of 2 mg cm&minus, 2 with a minor capacity loss of 0.36% per cycle for 100 cycles. This synthesis method of a unique porous carbon structure could provide a new avenue for the development of an electrode with a high retention capacity and high accommodated sulfur for electrochemical energy storage applications.

In this study, sludges generated from Ti-based flocculation of dye wastewater were used to retrieve photoactive titania (S-TiO

For the purpose of atmospheric NO removal, anatase TiO

The purpose of the study was to effectively treat algae bloomed water while using a Ti-based coagulant (TiCl4) and recover photoactive novel anatase TiO2 from the flocculated sludge. Conventional jar tests were conducted in order to evaluate the coagulation efficiency, and TiCl4 was found superior compared to commercially available poly aluminum chloride (PAC). At a dose of 0.3 g Ti/L, the removal rate of turbidity, chemical oxygen demand (COD), and total phosphorus (TP) were measured as 99.8%, 66.7%, and 96.9%, respectively. Besides, TiO2 nanoparticles (NPs) were recovered from the flocculated sludge and scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX), and X-ray diffraction (XRD) analysis confirmed the presence of only anatase phase. The recovered TiO2 was found to be effective in removing gaseous CH3CHO and NOx under UV-A lamp at a light intensity of 10 W/m2. Additionally, the TiO2 mixed mortar blocks that were prepared in this study successfully removed atmospheric nitrogen oxide (NOx) under UV irradiance. This study is one of the first to prepare anatase TiO2 from flocculated algal sludge and it showed promising results. Further research on this novel TiO2 concerning internal chemical bonds and shift in the absorbance spectrum could explore several practical implications.

We report an electrochemical sensor based on three-dimensional porous amorphous carbon (3DPAC) for the sensitive and selective determination of gallic acid (GA). The tailor-made carbon was prepared via salt-templating in which the organic molecular precursor, i.e., glucose, was simply ground and carbonized with a eutectic mixture of LiBr and KBr at 800 °C in an inert atmosphere. Salt removal from the carbon-salt mixture with water yielded 3DPAC with a hierarchical porous structure and oxygen-containing functional groups. When employed as an electrochemical sensor, 3DPAC exhibited remarkable sensitivity (0.1045 µA pM−1 cm−2) with a lower detection limit of 0.434 pM at a signal-to-noise ratio of 3 and a linear response up to 1–150 pM for determination of GA. Under optimized test conditions, 3DPAC showed a superior peak current response for GA as compared to the glassy carbon electrode. In addition, ascorbic, uric, and caffeic acids did not interfere with the voltammetric detection of GA in terms of selectivity, stability, and repeatability. We envision that 3DPAC can provide a promising platform for the development of electrochemical sensors.

A polymer hydrogel composed of alginate/humic acid/Fe-aminoclay was fabricated and utilized as a potential adsorbent for the removal of strontium ions (Sr 2 + ) from aqueous solution. The effects of adsorbate concentration, reaction pH, and time on the removal efficiency of Sr 2 + were investigated. The results revealed that the adsorption capacity increases as the Sr 2 + concentration increased from 1 to 10 ppm, which might be due to the more available adsorption sites. An additional increase in the Sr 2 + concentration had no effect. The optimal pH and reaction time for the removal of Sr 2 + were identified as pH 7 and 24 h, respectively, with an adsorbent dosage of 20 mg. The adsorption isotherm was fitted to the Freundlich model with a maximum Sr 2 + adsorption capacity of 45.65 mg g−1. The kinetic study showed that the adsorption behavior followed a pseudo-second-order kinetics. The hydrogel showed good selectivity toward Sr 2 + even in the presence of competitive cations having a higher concentration than Sr 2 + . From the above results, it is expected that this biocompatible hydrogel material can be used as an adsorbent for the removal of radioactive strontium.

The poor absorption of visible light and rapid recombination of photoexcited charge carriers are the two main factors responsible for the low photocatalytic activities of g-CN under sunlight. To mitigate these technical challenges, we utilize molten-salt synthesis based on alkali metal iodide. The high reactivity of LiI/KI does not allow the polycondensation of triazine dicyanamide intermediates further into PTI, the degree of which depends on the initial weight ratio of eutectic mixture to molecular precursor. This enables the controlled introduction of cyano functional groups with K+-coordination and decomposition of tri-s-triazine into triazine. The resulting all-in-one g-CN-I displays a photocatalytic hydrogen evolution reaction rate of 147 and 60 μmol/h from water under visible light and sunlight, respectively, which are 76 and 7 times higher than those of bulk g-CN. This study demonstrates the significant improvement in the photocatalytic activity of g-CN achievable through the synergistic combination of structural functionalities.

In this study, sludges generated from Ti-based flocculation of dye wastewater were used to retrieve photoactive titania (S–TiO2). It was heterojunctioned with graphitic carbon nitride (g-CN) to augment photoactivity under UV/visible light irradiance. Later the as-prepared samples were utilized to remove nitrogen oxides (NOx) in the atmospheric condition through photocatalysis. Heterojunction between S–TiO2 and g-CN was prepared through facile calcination (@550 °C) of S–TiO2 and melamine mix. Advanced sample characterization was carried out and documented extensively. Successful heterojunction was confirmed from the assessment of morphological and optical attributes of the samples. Finally, the prepared samples’ level of photoactivity was assessed through photooxidation of NOx under both UV and visible light irradiance. Enhanced photoactivity was observed in the prepared samples irrespective of the light types. After 1 h of UV/visible light-based photooxidation, the best sample STC4 was found to remove 15.18% and 9.16% of atmospheric NO, respectively. In STC4, the mixing ratio of S–TiO2, to melamine was maintained as 1:3. Moreover, the optical bandgap of STC4 was found as 2.65 eV, where for S–TiO2, it was 2.83 eV. Hence, the restrained rate of photogenerated charge recombination and tailored energy bandgap of the as-prepared samples were the primary factors for enhancing photoactivity.

AgPd alloy nanoparticles deposited on carbon nitride have been synthesized by a facile one-step reduction method and exhibit high catalytic activity at near room temperature (30 °C) for formic acid dehydrogenation, both under visible light and in darkness. The study proves that using the synergistic combination of alloying effects and metal-support interactions greatly enhances the catalytic activity of Pd-based nanocatalysts for hydrogen generation.

The growing demand for rechargeable batteries with high energy density has triggered research on batteries based on polyvalent cations such as Ca

Although sodium hybrid capacitors (NHCs) have emerged as one of the most promising next-generation energy storage systems, further advancement is delayed primarily by the absence of high-performance battery-type anodes. Herein, we report a nature-inspired synthesis route to prepare hard carbon anodes with high capacity, rate capability, and cycle stability for dual-carbon NHCs. Shape- and size-controllable crystal aggregates of inexpensive triazine molecules are utilized as reactive templates that perform triple duties of structure-directing agent, porogen, and nitrogen source. This enables the fine control of microstructure/morphology/composition and thereby electrochemical reactions toward Na-ion. The resulting hard carbon optimized in terms of lateral size, interlayer spacing, and surface affinity of graphene-like layers achieves a specific capacity of ∼380 mAh/g after 100 cycles at a current density of 250 mA/g mainly

A series of N-doped mesoporous carbon (NMC) materials are synthesized by the co-pyrolysis of an N-containing compound and carbon sources using a modified nanocasting method. The physicochemical properties are manipulated by changing the amount of resol precursors to permit the usage of these materials in the desired applications. As anodes for Li-ion batteries, the prepared NMC2, which has the highest number of hydrogenated N functional groups, delivers a high discharge capacity of 900, 700, and 600 mAh g−1 at current densities of 0.5, 1, and 2 A g−1, respectively, after 200 cycles of discharging and charging. Even at an extremely high current density of 10 A g−1, the NMC2 electrode delivers a discharge capacity of 300 mA g−1. In addition, in Na-ion batteries, NMC3, which has the highest pyridinic N content and average pore diameters, exhibits a discharge capacity of 163 mAh g−1 at 1 A g−1 over 500 cycles. Hence, an intimate relationship between the key physicochemical parameters and electrochemical properties of NMC materials are established for use of these materials in specific applications. The obtained results demonstrate that the fabricated NMC materials possess superior characteristics in comparison to those of most state-of-the-art porous carbon materials.

For the purpose of atmospheric NO removal, anatase TiO2/g-CN photocatalytic composites were prepared by using a facile template-free calcination route in atmospheric conditions. Considerably fiscal NP400 and laboratory-grade melamine were used as the precursor of the composites. Additionally, samples were prepared with different wt. ratios of TiO2 and melamine by using two distinct calcination temperatures (550 °C/600 °C). The morphological attributes of the composites were assessed with X-ray diffraction, scanning and transmission electron microscopy, infrared spectroscopy, and X-ray photoelectron spectroscopy. Additionally, the optical traits were evaluated and compared using UV–visible diffuse reflectance spectroscopy and photoluminescence analysis. Finally, the photodegradation potentials for atmospheric NO by using the as-prepared composites were assessed under both UV and visible light irradiation. All the composites showed superior NO oxidation compared to NP400 and bulk g-CN. For the composites prepared by using the calcination temperature of 550 °C, the maximum NO removal was observed when the NP400 to melamine ratio was 1:2, irrespective of the utilized light irradiation type. Whereas for increased calcination temperature (600 °C), the maximum NO removal was observed at the precursor mix ratio of 1:3 (NP400:melamine). Successfully narrowed energy bandgaps were perceived in the as-prepared composites. Moreover, a subsequent drop in NO2 generation during NO oxidation was observed under both UV and visible light irradiation. Interestingly, higher calcination temperature during the synthesis of the catalysts has shown a significant drop in NO2 generation during the photodegradation of NO.

A 3D cubic structure of mesoporous graphitic carbon nitride (3D-g-CN) was fabricated by nano casting using the mesoporous silica hard template KIT-6. The abundant intrinsic amine functionalities of 3D-g-CN were applied as a selective adsorbent for silver ions using the unique affinity of silver and amine functionalities. The large surface area of 3D-g-CN resulted in increased amine functionalities at the surface and enabled it to form complexes with silver ions. As a result, almost 400 mg/g of silver ion could be removed from 100 mM of initial solution at 293.15 K. The isotherm of silver ion adsorption onto 3D-g-CN was described by the Freundlich and Sips models and indicated heterogeneity of the adsorbent surface. Thermodynamic parameters determined from temperature dependent isotherms were verified by the endothermic silver ion adsorption process of 3D-g-CN. The adsorption capacity of silver ion on 3D-g-CN was maintained during several reuses without a significant decrease in capacity. Overall, the results indicate that 3D-g-CN has intrinsic amine functional groups with a large surface area and could therefore be utilized as an efficient selective adsorbent of silver ions for water purification.

Graphitic carbon nitride (g-C3N4) is widely considered as a promising visible-driven photocatalyst. It is a type of inexpensive, air-stable, and non-toxic material that has been proven to exhibit high performance in photocatalysis. For more efficient use of solar energy, it is necessary to enhance the light absorption of g-C3N4. To take advantage of the near-infrared (NIR) region of the solar energy, g-C3N4 was combined with upconversion nanoparticles (UCNPs), in this study. The UCNPs can convert NIR photons into ultraviolet (UV) and visible light, which can then activate the g-C3N4 photocatalyst. The use of visible and NIR light sources improves the photocatalytic activity of the UCNPs/g-C3N4 nanocomposite. In order to optimize the photocatalytic efficiency of the nanocomposite, the absorption and emission wavelengths of the UCNPs were tuned by controlling the lanthanide dopant composition where the core UCNPs were coated with an inner active shell and an outer inert shell. It is shown in this study that the nanocomposite can exhibit excellent photocatalytic activities under simulated solar light illumination.

Bacterial pathogens of water origin have potential public threats thus suggesting the need of developing efficient and sustainable water disinfection strategies from waterborne pathogens. We set out to synthesize different controlled morphologies of graphitic carbon nitride (g-C

We propose a nanostructured Mn-doped V2O5 lithium-ion battery cathode material that facilitates cathodic charge transport. The synthesis strategy uses a layered compound, vanadium(III) jarosite, as the precursor, in which the Mn2+ ions are doped uniformly between the vanadium oxide crystal layers. Through a two-step transformation, the vanadium jarosite was converted into Mn2+-doped V2O5. The resulting aliovalent doping of the larger Mn cations in the modified V2O5 structure increases the cell volume, which facilitates diffusion of Li+ ions, and introduces oxygen vacancies that improve the electronic conductivity. Comparison of the electrochemical performance in Li-ion batteries of undoped and the Mn2+-doped V2O5 hierarchical structure made from layered vanadium jarosite confirms that the Mn-doping improves ion transport to give a high cathodic columbic capacity (253 mAhg–1 at 1C, 86% of the theoretical value, 294 mAhg–1) and excellent cycling stability.

A high-yielding synthesis of a series of polyimide dendrimers, including decacyclene- and perylene-containing dendrimer D6, in which two types of polyimide dyes are present, is reported. In these constructs, the branching unit is represented by trisphenylamine, and the solubilizing chains by N-9-heptadecanyl-substituted perylene diimides. The photophysical properties of the dendrimers have been studied by absorption, steady-state, and time-resolved emission spectroscopy and pump–probe transient absorption spectroscopy. Photoinduced charge-separated (CS) states are formed on the femtosecond timescale upon visible excitation. In particular, in D6, two different CS states can be formed, involving different subunits that decays independently with different lifetimes (ca. 10–100 ps).

We report utilization of graphitic carbon nitride (g-CN) as an electrocatalyst for dye-sensitized solar cells (DSSCs). Crystalline poly(triazine imide) based g-CN was synthesized via a modified ionothermal method, and deposited onto the counter electrodes along with a conductive additive and a sacrificial polymer binder. The resulting DSSCs exhibited a power conversion efficiency (7.8%) comparable to that of conventional Pt catalyst (7.9%), confirming the excellent catalytic activity of poly(triazine imide) g-CN as a non-precious metal electrocatalyst.

Organic graphitic carbon nitride nanoparticles (NP-g-CN), less than 30 nm in size, were synthesized and evaluated for photodynamic therapy (PDT) and cell imaging applications. NP-g-CN particles were prepared through an intercalation process using a rod-like melamine-cyanuric acid adduct (MCA) as the molecular precursor and a eutectic mixture of LiCl-KCl (45:55 wt%) as the reaction medium for polycondensation. The nano-dimensional NP-g-CN penetrated the malignant tumor cells with minimal hindrance and effectively generated reactive oxygen species (ROS) under visible light irradiation, which could ablate cancer cells. When excited by visible light irradiation (λ > 420 nm), NP-g-CN introduced to HeLa and cos-7 cells generated a significant amount of ROS and killed the cancerous cells selectively. The cytotoxicity of NP-g-CN was manipulated by altering the light irradiation and the BP-g-CN caused more damage to the cancer cells than normal cells at low concentrations. As a potential non-toxic organic nanomaterial, the synthesized NP-g-CN are biocompatible with less cytotoxicity than toxic inorganic materials. The combined effects of the high efficacy of ROS generation under visible light irradiation, low toxicity, and bio-compatibility highlight the potential of NP-g-CN for PDT and imaging without further modification.

Although numerous research efforts have been made for the last two decades, the chronic problems of lithium-sulphur batteries (LSBs), i.e., polysulfide shuttling of active sulphur material and surface passivation of the lithium metal anode, still impede their practical application. In order to mitigate these issues, we utilized polyimide functionalized glass microfibers (PI-GF) as a functional separator. The water-soluble precursor enabled the formation of a homogenous thin coating on the surface of the glass microfiber (GF) membrane with the potential to scale and fine-tune: the PI-GF was prepared by simple dipping of commercial GF into an aqueous solution of poly(amic acid), (PAA), followed by thermal imidization. We found that a tiny amount of polyimide (PI) of 0.5 wt.% is more than enough to endow the GF separator with useful capabilities, both retarding polysulfide migration. Combined with a free-standing microporous carbon cloth-sulphur composite cathode, the PI-GF-based LSB cell exhibits a stable cycling over 120 cycles at a current density of 1 mA/cm2 and an areal sulphur loading of 2 mgS/cm2 with only a marginal capacity loss of 0.099%/cycle. This corresponds to an improvement in cycle stability by 200%, specific capacity by 16.4%, and capacity loss per cycle by 45% as compared to those of the cell without PI coating. Our study revealed that a simple but synergistic combination of porous carbon supporting material and functional separator enabled us to achieve high-performance LSBs, but could also pave the way for the development of practical LSBs using the commercially viable method without using complicated synthesis or harmful and expensive chemicals.

Bacterial pathogens of water origin have potential public threats thus suggesting the need of developing efficient and sustainable water disinfection strategies from waterborne pathogens. We set out to synthesize different controlled morphologies of graphitic carbon nitride (g-C3N4) polymer, evaluate their comparative effects on the generation of reactive oxygen species (ROS), and investigate potential applications in water purification systems. Characterization of the synthesized microstructures of g-C3N4, such as melamine-cyanuric acid (MCA)-based rosette-type, rod-type, 2D hexagonal, and 3D cubic mesoporous silica was accomplished using Fourier transform infrared (FT-IR), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), X-ray diffractometry (XRD), and transmission electron microscopy (TEM). The microbial inhibitory potential of 2D g-C3N4 photocatalyst against waterborne Escherichia coli, Staphylococcus aureus, and Salmonella typhimurium was evaluated based on the effective activity of 2D g-C3N4 upon visible light excitations. The microbicidal efficiency of 2D g-C3N4 was evident within 30 min of visible light exposure via direct interaction, while other microstructures of g-C3N4 demonstrated only slight antimicrobial effects after 120 min, with insufficient ROS generation. The antimicrobial and ROS-generating effects of 2D g-C3N4 depended on the type and surface area of the synthesized 2D g-C3N4 material. Considering its availability and excellent disinfection activity, 2D g-C3N4 obtained from simple and convenient facile synthesis is a promising solar-driven photocatalyst for clearing microbial contamination from water.

Simple organic cooperative assembly of triazine molecules leads to three-dimensional macroscopic assemblies of low-dimensional graphitic carbon nitrides (g-CNs), for example, nanoparticles, nanotubes, and nanosheets. The approach enables the characterization of the cooperative properties and photocatalytic activities of low-dimensional g-CN materials in hydrogen evolution reactions from water under visible light. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Graphitic carbon nitride (g-CN) is a promising heterogeneous metal-free catalyst for organic photosynthesis, solar energy conversion, and photodegradation of pollutants. Its catalytic performance is easily adjustable by modifying texture, optical, and electronic properties via nanocasting, doping, and copolymerization. However, simultaneous optimization has yet to be achieved. Here, a facile synthesis of mesoporous g-CN using molecular cooperative assembly between triazine molecules is reported. Flower-like, layered spherical aggregates of melamine cyanuric acid complex (MCA) are formed by precipitation from equimolecular mixtures in dimethyl sulfoxide (DMSO). Thermal polycondensation of MCA under nitrogen at 550 °C produces mesoporous hollow spheres comprised of tri-s-triazine based g-CN nanosheets (MCA-CN) with the composition of C3N4.14H1.98. The layered structure succeeded from MCA induces stronger optical absorption, widens the bandgap by 0.16 eV, and increases the lifetime of photoexcited charge carriers by twice compared to that of the bulk g-CN, while the chemical structure remains similar to that of the bulk g-CN. As a result of these simultaneous modifications, the photodegradation kinetics of rhodamine B on the catalyst surface can be improved by 10 times.

Uncontrolled hemorrhage is a leading cause of potentially preventable death. The most effective commercial hemostatic products employ layered clays. Due to safety concerns only a product containing kaolin is currently recommended by the U. S. Department of Defense. A problem related to layered clays, including kaolin, is their cytotoxicity. Also, material left in the wound can lead to thrombosis and other adverse effects. Recently, it has been shown that pure silica mesocellular foams (MCF) with cell window sizes >20 nm are effective in promoting blood clotting. Here, we tested the potency and cytotoxicity of layered clays in comparison to MCF with a cell window size of 26 nm (MCF-26) in vitro. The results showed that the potencies of MCF-26 and layered clays in promoting clotting were comparable. Effects on cell viability were assessed with relevant primary human cell types. The cytotoxic effects of all compounds were cell type-specific and most sensitive were endothelial cells. The IC50 values of MCF-26 were in the mg ml−1 range and its cytotoxicity was ∼1–2 orders of magnitude lower than the cytotoxicity of layered clays. Further, MCF-26 did not adhere strongly to cell surfaces and was not taken up by cells as observed for the layered clays. This suggests that it would be easier to remove MCF-26 from wounds. Altogether, the results suggest that MCF-26 would be effective and safer than currently used hemostatic agents.